Search Documents

By Frank R. Van Horn

It is customary to ascribe two general modes of occurrence to natural gas, namely, shale gas which, as the name indicates, is found in shale, and reservoir gas, which occurs in sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts. Historical Outline The oldest well producing reservoir gas in the district was drilled in 1886 in Newburg for what was then known as the Cleveland Rolling Mill Co. This well was 3,000 ft. deep, and was thought to have reached the "Clinton" formation. Two "sands" showing small amounts of oil were recorded in the Niagara limestone at depths of 2,658 and 2,686 ft. This is about the horizon of the so-called Newburg sand which has proved to be of some importance as a source of gas and oil by recent drilling operations. The rock pressure was reported to be 400 to 500 lb. per square inch, but since the volume was only 14,000 to 16,000 cu. ft. daily, the well was not only considered unsuccessful but was thought to prove the absence of high-pressure gas in commercial quantities in the Cleveland district.

Jan 1, 1917

By David R. Mitchell, E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are-presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and conform, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance comes and jigs are usually dispensed with, and other methods, such as the Hydro-tator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh.

Jan 1, 1950

By E. S. Davenport

IT is indeed an honor and a responsibility to have been selected to present the thirty-fourth in this series of Henry Marion Howe lectures, established to perpetuate the memory of a great teacher and one of America's outstanding scientists. Previous Howe lecturers have established high standards for this annual AIME event. It has been my good fortune to have enjoyed close association with five of these former lecturers; namely, Bain, Grossmann, Johnston, Sosman, and Vilella, all of whom have been prominently identified with the research activities of the organization with which I am connected. Some years ago I had an opportunity to examine a letter written by Professor Howe in 1904. This document was particularly interesting to me since I never had the privilege of personal acquaintance with Professor Howe and do not recall even having seen him during his long and active career. In view of the fact that the letter dealt, to some extent, with matters related to the subject of today's lecture, I would like to quote briefly from it. The letter is datelined, "Bad Kissingen, June 11, 1904." The salutation reads, "Dear Bradley," which suggests that it was probably addressed to Bradley Stoughton, who, I believe, was working with Howe at Columbia University at that time. The letter reads, in part, as follows: "Austenite and Martensite. I have not examined what Osmond says in his new book. His former remarks about austenite I found very confusing, indeed unintelligible. I think we can reconcile matters well enough for the present by assuming that martensite is a transition step between austenite at one end and ferrite and cementite at the other. Above critical range for steel of 0 to 1.80 carbon, austenite is normal state; below Ar1, ferrite and cementite are normal." The letter then continues with a discussion of Osmond's ideas on metallographic nomenclature, particularly his use of the terms martensite, troostite, and sorbite, including the following pointed comment: "For common purposes it seems to me unwise to drag them in, and much simpler to confine ourselves to the end stages Austenite Ferrite plus Cementite Osmond does not really know his own mind— or does not clarify his ideas to others—as to nomenclature." Thus we see that, as far back as 1904, the transformation of austenite, and the products of that

Jan 1, 1958

By H. A. Guess

Introduction. History and Production Statements. Southeast Missouri is the oldest of the large producing districts of the United States. The first recorded production from disseminated ores was in 1869, although for many years prior to that time lead had been milled from shallow pockets, and steady growth in production has been shown ever since, the greatest increases being during the past five years. The production by years for each of the operating companies from 1869 to 1907, inclusive, is given in Table I. In Table 11. is given the production by years from 1908 to 1912, inclusive, for the district as a whole, showing the tonnage of crude ore mined, yield in concentrates, average assay of concentrates; yield in metallic lead both per ton of crude ore and in total; also approximate value of the yearly production. It is interesting to note that the production for the 5-yr. period 1908 to 1912, inclusive, is practically equal to the total previous production, viz., the 39-yr. period 1869 to 1907, the summary being as follows:

Jan 1, 1915

By Thomas N. Walthier

ROSPECTING for uranium in the East is hampered by the lack of bedrock exposure due to extensive overburden and residual soil. But, despite the problems of this physiographic province, it has not been ignored in the search for radioactive materials. Since 1951 both the U.S. Geological Survey and the Atomic Energy Commission have had field parties in the eastern U.S. Tempo of private prospecting is increasing, and many discoveries have resulted. AEC work so far has been concentrated in the areas of most numerous discoveries-Pennsylvania, New Jersey, and New York. Accounts of uranium mineralization in the eastern U.S. are found in the old literature and one site in the Mauch Chunk area of Pennsylvania has been known since 1874. In 1949 McKeown examined the original occurrence there and found another southeast of the town. The deposit appeared to have commercial possibilities and a short period of production began in July 1954

Jun 1, 1955

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By C. W. Gennet

Announcement was made in the spring of 1926 that the Boston & Maine R. R. Co. had contracted with the well-known German steelmakers, Messrs. Fried Krupp, for the manufacture of 15,000 tons of basic open-hearth steel rails at the Rheinhausen Works, for delivery to Boston, Mass. The manufacture of rails in the United States has for many years been almost a national pride, and as this feeling is chiefly the result of a long-time liberal and consistent patronage of American rails by American railroads, it is not strange that this somewhat unusual announcement should arouse more than ordinary interest. Since the end of the World War, the importation of foreign rail has been fairly large, principally because the newly created economic conditions have rendered some American competition more difficult, but the tonnage imported, for the most part, has been made up of small orders for miscellaneous use; and the contract referred to constitutes the largest single importation of foreign rail in over ten years. In 1915, the Algoma Steel Co. of Sault Ste. Marie, Canada, supplied the Illinois Central R. R. with 30,000 tons of rails,' and various other American roads with smaller amounts. In 1902, 1903 and 1904, large tonnages of rail from abroad were purchased, the Louisville & Nashville R. R. alone obtaining 30,000 tons from German mills. It is the object of this paper to present, in what is believed to be a new and concise form, figures showing the production and consumption of rails in the United States, and to record some of the testing and inspection results of the recent Krupp rails; also, to direct attention to two quite unique departures from American practice that were regular features of the Krupp process and which are worthy, it is thought, of careful study. Production and Consumption of Rails in the United States Table 1 shows the tonnage of rail produced in the United States and the amount imported, exported, and consumed by years since 1849. That, evidently, was the first year of record, for the statistics of the American Iron and Steel Institute and its predecessor, the American Iron and

By G. H. Gronhovd, W. H. Oppelt

Complete gasification to produce synthesis gas for manufacture of synthetic chemicals and fuels offers possibilities for utilization of the vast lignite fuel deposits in the U.S. The design of a slugging, fixed-bed, pressure gasification pilot Plant is described. Results are presented for initial operation of the plant at moderate pressure and using low-temperature char as fuel. Gasification of solid fuels is becoming increasingly important in the future overall energy picture, both in this country and abroad. Snythesis gas from gasification of coal consists chiefly of carbon monoxide and hydrogen, and after suitable purification and modification this gas can be used in the production of synthetic ammonia, methanol, higher alcohols, and synthetic liquid fuels, or as a reducing gas in the metallurgical field.' Most synthesis gas used in this country is made from natural gas, petroleum oils, and refining tail-gases, but the direct gasification of coal will become more attractive as costs of petroleum oils and natural gas increase.' A gasification process designed for use with brown coal and lignite was developed by the German Lurgi Co. prior to World War 11. In this process a fixed bed of lump-sized fuel is gasified with steam and oxygen at pressures ranging from 370 to 440 psi. Effective heat exchange between the ascending high-temperature gases and the descending solid fuel results in low gas outlet temperatures, high thermal efficiency, and favorable oxygen consumption. Lurgi gasifiers are used commercially for the production of synthesis gas or as a substitute for coal gas in many countries, including Germany, Czechslovakia, Great Britain, South Africa, Australia and Pakistan.3-6 The chief disadvantage of the conventional Lurgi gasifier which operates under nonclinkering conditions is that large quantities of excess steam must be supplied with the oxygen-steam mixture to reduce the temperature in the fuel bed below fusion temperature of the ash. Most of the steam leaves the gasifier undecomposed with the product gas and, after cooling, produces large amounts of dilute liquor. Evaluation of fixed-bed gasification experiments using dry-ash removal indicated that by increasing the oxygen concentration in the oxygen-steam blast the temperature in the combustion zone could be raised high enough to operate under slagging conditions. 7-8 Operation of a fixed-bed pressure gasifier under slagging conditions would reduce the steam requirements and the volume of waste liquor and would increase the steam decomposition, the overall thermal efficiency of the process, and the rate of gas production per unit cross sectional area of the gasifier. Because the Lurgi gasification process, modified for slagging operation, offered possibilities for efficient gasification of American lignite, the Bureau of Mines decided to investigate the process on a pilot-plant scale at the Grand Forks, N. D., Lignite Research Laboratory. DESIGN Description of Pilot Plant: A flowsheet of the Grand Forks slagging gasification pilot plant is presented in Fig. 1. The gasifier unit consits of the coal lock, the gas generator, and the slag lock. The fuel, which is periodically charged to the coal lock, moves by gravity flow into the generator and is continuously gasified by an oxygen-steam mixture introduced at the bottom of the gasifier. Molten slag is formed at the hearth and flows through a central taphole into a water quench bath. The slag-water slurry is periodically discharged from the slag lock. Process steam is generated and superheated in separately-fired, oil-burning units. Oxygen is supplied to the gasifier from a gas storage bank located some distance from the pilot plant. The capacity of the oxygen storage bank is about 130,000 standard cu ft at 2200 psig. Liquid oxygen is delivered by truck and is converted to gas during the filling operation. The superheated steam and oxygen are metered separately, then mixed and fed to the gasifier tuyeres. The gas generator is surrounded by a water jacket. The steam formed is separated in the steam drum and then discharged to the gas offtake, thus equaliz-

Jan 1, 1961

By W. L. Fink, L. A. Willey

This paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium relations have been determined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and aluminum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith † suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extentl,2,3 The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are distinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns. Previous Investigations The solid solubility of magnesium in aluminum has been well established by the work of Dix and Keller4, Schmid and Siebe15, and Saldau and Sergeev6. There is no agreement as to the composition of the magnesium constituents at the aluminum end of the binary aluminum-magnesium system. Hanson and Gayler7 report Mg2Al3; Boyer8 found that the alloy

Jan 1, 1937

By J. E. Kirby, L. B. Schnitz, H. E. Stamm III

The production history of a gas-cap-drive reservoir was reproduced by calculations, and predictions were made for operations under primary depletion, pressure maintenance by gas injection, and pressure maintenance by water injection. Although the general equations used in this analysis have been available to the industry for a number of years, the procedure has not had extensive use because of the unusually large time requirements for developing numerical results. The use of digital computing equipment for processing the calculation work generally reduced the time usually required for an extensive analysis of this type. Calculation techniques were developed that were equally applicable for solving the gar-cap-drive problem, whether digital computing equipment or desk calculators are used. These techniques are outlined and the procedures are illustrated by the field problem. INTRODUCTION The analysis of a gas-cap-drive res-ervoir requires the simultaneous solution of the volumetric balance1 and displacement2 equations. Equations for the analysis of combination drive reservoirs were presented by Wooddy and Moscrip in a previous paper." These equations permit the evaluation of possible operating processes in order that the optimum method of pro- ducing the reservoir may be determined. Although these equations represent the basic technique known for the detailed analysis of gas-capdrive reservoirs, the calculation processes are quite complex and time consuming; hence, the procedure has not had extensive use. Recently, these equations were satisfactorily applied with the aid of a digital computer to investigate the completion history of a gas-cap-drive reservoir under the following operating methods: primary depletion, depletion under full pressure maintenance by gas injection, and depletion under full pressure maintenance by water injection. The use of digital computing equipment substantially reduced the time necessary for making the computations and permitted a more concise investigation of the reservoir's depletion history than was possible when the desk calculator was used. This more rigorous investigation also permitted a detailed analysis of the calculation procedures necessary in the solution of the gas-cap-drive problem. This paper outlines the procedure of analyzing a gas-cap-drive reservoir and illustrates the process with an actual field problem. CHARACTERISTICS OF THE RESERVOIR ANALYZED Production in the field under consideration is obtained from a Frio formation of Oligocene age at a depth of approximately 5,740 ft sub-sea. The accumulation, which is bounded on the flanks by strand lines, is semirectangular in shape with gentle narrowing toward the base of the structure as shown by the sand limits and completion map in Fig. 1. The reservoir development indicates an oil column of 319 ft that is defined by gas-oil and oil-water contacts. Basic data relative to the characteristics of the formation and the formation fluids are shown in Table 1. The formation exhibits considerable shaliaess and thinning near the oil-water contact indicating that little or no benefit will be received from natural water influx. This is substantiated by the fact that wells completed near the original oil-water contact have not produced water. A sizeable gas cap is present; however, considerable faulting is in evidence, and it is believed that only a limited portion of the gas cap will aid in oil displacement and pressure maintenance. Although the reservoir was in an initial stage of depletion, it was believed that as soon as the equilibrium gas saturation in the oil zone was exceeded and a number of upstructure wells were invaded by the expanding gas cap, the resulting high gas-oil ratio production would rapidly dissipate the natural drive and lead to limited oil recoveries and inefficient reservoir operation. This analysis evaluated the effectiveness of the primary displacement mechanism and

Jan 1, 1958

By William F. Butler, Mo-Hung Che

DEVELOPMENT OF MONEY AND MONEY STANDARDS This chapter is concerned with the rise, and then the decline and fall, of gold and silver as monetary metals. As a first step in tracing the history of this process, it is necessary to consider the nature of money, and the manner in which different forms of money have developed over the centuries. The origins of money go back into deepest antiquity. Once men ceased to be pure nomads and entered into even a rudimentary form of society such as clans or tribes, money had to be invented The first step was barter as farmers or hunters swapped their surplus products for things produced by artisans such as shoes, clothing, and simple tools. But such barter trading is inconvenient even in primative societies It is difficult to match up buyer and seller at any point in time There are problems in arriving at viable and acceptable terms of exchange. The accumulation of savings-wealth-is complicated. No one can be sure that a pile of furs, or wheat, or certainly fish or game can be used in the future to trade for other goods or services. So even prehistoric man saw the need for money. There was a need first for something to serve as a medium of exchange This was an essential first step in the process of specialization-or the division of labor. A farmer, a hunter, or a shoemaker could only devote his full efforts to his trade if he could be sure that he could exchange his surplus production for the other things he needed for existence. This required a medium of exchange-a form of money which would be broadly acceptable. Money was needed for two other reasons Some system of market prices was essential to facilitate the exchange of goods and services. This required some form of common denominator-some standard of value-to govern the exchange process. And there was also need for something to serve as a store of value, a place to put any excess production (savings) with the assurance that it can be used in the future to acquire a general range of goods and services. As a result, money, in one form or another, developed at a very early state in civilization. Yet the centuries have been marked by a search for a form of money which will possess in full measure all of the attributes in money-a reliable and universally acceptable medium of exchange, standard of value, and store of value. -A wide variety of things have been used as money at one time or another: shells, beads, stones, feather, metals, and even the teeth of sharks and dogs. Some of these things were obviously of little or no practical value. They were used because people had confidence in their continued acceptance as a medium of exchange. As the world evolved and as trading ex-

Jan 1, 1976

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By G. W. Preckshot, J. W. Gorman

MOLTEN metals offer an excellent medium for the study of molecular diffusion and interphase transfer. In the absence of intermetallic compound formation, solutions of molten metals are solutions of elements. Therefore, complicating factors such as molecular structure, dissociation, association, polarization, and so on, are generally absent. Further, metals remain in the liquid state over a wide range of temperature. Thus, the effect of temperature on transport processes can be studied in more detail. Although some data are available for the diffusion of metals in the molten state at high temperatures,"""".'!' the most useful and accurate data are those for the diffusion of various elements in mercury at room temperature. The effective radius of diffusion for the various elements in mercury may be calculated from the Stokes-Einstein relation.'-These calculated radii are compared with the atomic and ionic radii calculated from X-ray data on crystals." The effective radii of diffusion of the alkali and alkali-earth metals correspond to those of the neutral atom; those of cadmium, silver, lead, zinc, thallium, bismuth, and tin correspond to ionic radii; and those of copper and gold indicate larger radii due to association with mercury or more likely, faulty diffusion data. Independent evidence"' supports the notion that alkali metals are uncharged in amalgams. The concept of metals moving free of their conductance electrons in the liquid state has been discussed by Eyring, et al,'" in connection with studies on the viscosity of pure molten metals. Considering the approximate nature of the tabulated atomic and ionic radii and the variance in the diffusion measurements, the application of the Stokes-Einstein equation to the diffusion of metals in mercury gives gratifying results. It is noted that a number of these metals have article radii eaual to or less than those of the solvent mercury.".'*,"' Soba1,'" sing the inaccurate Roberts-Austin20 data, indicated that the effective radius of diffusion might well be a function of temperature. Additionally in studies of mass transfer between phases, many conflicting opinions have been expressed concerning the assumption of equilibrium at the interface." ,","," The results of the present work on the diffusion of solid copper in molten lead throws light on the tempera- ture variation of the diffusion radius as well as the extent of the interfacial resistance. The theoretical background and experimental procedure are presented here in detail. Results on other systems will be presented in subsequent papers. Nomenclature The following nomenclature is used in the paper: A—cross-sectional area of diffusion column, sq cm C, C,—concentration of solution and saturated solution respectively, g per cc D,D'—-diffusivity, sq cm per sec e—Naperian base h—ratio, k/D k—mass-transfer coefficient, cm per sec L—diffusion column length, cm n—series index q—flux, g per sq cm-sec r—radius, cm or A R—-gas constant t—time, sec T—temperature, K V—volume, cc w—weight of copper-lead alloy on copper cylinder WT—-total copper transferred to lead diffusion, column, g Z—distance from top of diffusion column, cm 2'—distance from copper-lead interface, cm (2' = L-2) u,,—roots of diffusion equation Mathematical Apparatus The model shown in Fig. 1 applies to the diffusion of solid copper into molten lead. Here Fick's first law may be written where all terms are defined in the nomenclature. It is assumed that the volume of the lead column is constant. This is justified since experimental densities compared favorably with calculated densities based on perfect interstitial mixing. Thus there is no counter diffusion of lead. It is clear that 2 in Equation [I] should be measured relative to the interface which moves relative to the diffusion cell but not to the liquid phase. Hence, the frame of reference is the plane of the copper-lead interface. The diffusivity calculated at constant volume, D", is that defined by Hartly and Crank" and is designated herein as D. No Interfacial Resistance—The two situations of the presence and absence of interfacial resistance will be treated. The simplest is the latter which re-

Jan 1, 1959

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won't be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

By D. J. Weintritt, J. C. Cowan

Methods of studying oilfield mineral .scale deposition in the laboratory do not work for barium sulfate because only small nonadhering crystals ore formed. On the other hand, barium sulfate scale found in down-hole or surface equipment is strongly adhering and may contain very large crystals. Results suggest that most of the difference derives from the extremely low .solubility of barium sulfate. Firm adherence of scale and the consistent development of oriented crystals 100 microns and larger suggest a relationship between scale adherence and crysta1 growth. Data from this study indicate some reasons for barium sulfate's occurring as a deposit in oilfield waters. The unique characteristics as well as the associative properties of barium sulfate scale as related to calcium carbonate and calcium sulfate ere shown. INTRODUCTION The first observed deposition of barium sulfate scale in oilfield production equipment is unknown but probably coincides closely with the beginnings of the oil industry itself. Moore' described barite oolites in some producing wells in the Saratoga field, Tex., in 1914. Currently, positive identification of barium sulfate deposition is recorded in most of the major oil-producing areas of the United States. As efforts continue to identify the composition and functions of the materials found in scale deposits, the geographic and economic importance of the part played by barium sulfate will become even more important. This belief is based on the following Facts. 1. Many oil fields in the U.S. are in or entering their mature phase and the volume of produced water is increasing; thus, the cumulative effects of low-solubility minerals become more significant. 2. Secondary recovery techniques and increased emphasis on waste disposal systems require controlling the behavior of all constituents of water to prevent formation plugging. 3. The more general use of instrumental analysis has reduced the time and improved the accuracy of complete scale and water analysis. 4. Once formed, barium sulfate scale is resistant to present methods of chemical removal; therefore, costly mechanical methods are necessary. Thus, new methods of prevention and control will require specialized chemical techniques and better knowledge of the causes of scaling. Consider the results of some simulated field deposition studies illustrating this need (Fig. 1). The studies utilized a Scale Deposition Test Cell* and each coupon was exposed to 8,000 ml of a 300 me/liter solution of the various types of mineral scale. All tests were conducted at 140F. Only the calcium sulfate and calcium carbonate deposited scale. The solution containing 300 me/liter of barium sulfate exhibited copious amounts of precipitate, but none of the precipitate adhered. The fluids from the effluents were also allowed to impinge on glass slides. Fig. 1 shows the relative adherence of the three types of scale on unetched glass. The barium sulfate failed to deposit in the same manner as the calcium carbonate and calcium sulfate solutions.

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,' or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

THE. extraordinary volume of work done in this period, and the multiplicity of subject matter, make a year-by-year historical account undesirable, if the account is not to be an assembly of unrelated fragments. We shall, instead, undertake to narrate the development in this period of each of the branches of the subject separately, hoping that their interrelations will be self-evident. There is a certain arbitrariness in the selection of subject matter in the following sections. The development of important engineering alloys-for example, high-speed steel-is disregarded, for it is the primary purpose of this account to relate the advances in ideas, the growth of the science of metals; other historical accounts relate these parallel advances. Nor are advances in techniques stressed, though occasionally the most important are noted; nor is the progress described in allied fields such as welding, cutting, etc.; for though these developments have very frequently made possible the advances herein related, they are far too numerous to recount in anything short of a ponderous volume. There is a more serious arbitrariness, however; it is not an easy matter to draw the boundaries of physical metallurgy, and some contiguous subjects have been omitted that perhaps should have been included, such as, for example, corrosion, gases in metals, the magnetic behavior of metals and alloys, and certain other fields in the physics of metals. REACTIONS IN ALLOYS--DIFFUSION Many of the reactions occurring in alloys proceed by the operation of the process of diffusion in the solid state: the annealing of mixed powders to form alloys, the homogenization of castings or forgings, the freezing of alloys, the treatment of clad metals, the loss

Jan 1, 1948

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By R. G. Hite, R. G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mechanics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1984