Search Documents

By Morris M. Fine, Norwood B. Melcher

As a raw material, prereduced pellets can be considered symptomatic of the quiet revolution taking place in the quality and grade of blast furnace burdens for the past decade. In 1954, the average analysis of ores from U.S. ranges in the Great Lakes area was 50.86% Fe (natural), 10.22% SiO2, and 10.90% moisture; ten years later, the average was 56.67% Fe (natural), 8.13% SiO2, and 6.17% moisture. The advance in Canada was even more pronounced in a lesser number of years. In 1957 the average product of Canadian ore-producing areas was 51.62% Fe (natural), 8.59% Si02, and 8.02% moisture; in 1964, the average grade was 59.59% Fe (natural), 6.27% SiO2, and 3.94% moisture.2 These dramatic data are testimony to the giant strides made in iron ore improvement, and the next logical step is prereduction. Prereduction can well be considered as a beneficiation step in which oxygen is the gangue. Since the ultimate objective of milling and smelting is iron metal, non-metallic constitutents in general, whether oxygen or silica, are contaminants. The past and continuing attack aimed at lowering the silica content of concentrates is succeeding. One need only thumb through the Grade Name listings of the American Iron Ore AssociationVo note that virtually all commercial pellets contain less than 8% silica, many are lower than 6%, and a few below 45%. With natural technical evolution, it is expected "many" rather than "few" will ultimately be in the last category and further mechanical concentration will have reached the point of diminishing returns. At this level, oxygen would constitute the only major diluent worthy of attack.

Jan 7, 1966

By C. F. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by some typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects. [ ] In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

Jan 1, 1928

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE studies of the mechanism of precipitation and of the resulting property changes in aluminum-silver alloys1-3 have presented some new concepts of the aging reaction-concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.1,4 These platelets grow in lateral dimensions and in thickness with aging time until they are thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstätten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuous precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 EXPERIMENTAL PROCEDURE The alloys were made using 99.97 per cent Al or distilled magnesium, with

Jan 1, 1943

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1964

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By J. A. Heskett

NEW ZEALAND is dependent on the outside world for its ferro goods, yet it can boast of at least two well-defined iron-ore deposits; namely, Para Para limonite, 3 Fe203 + 21120 also found as lower hydrated oxides, and Taranaki iron-sand, a combined magnetite and ilmenite, 2FeO + 2Fe203 + FeO + Ti02. The former is of massive variety and the FIG. 1.-VIEW OF WORKS SHOWING IRON-SAND DEPOSITS, ALSO WHARF AND BREAK¬WATER IN THE DISTANCE. latter granular and mixed with various proportions of fine shell and siliceous sand well water-worn. This latter deposit forms the greater portion of the beach sands of the west coast of the North Island of New Zealand. It is so fine that the whole of a sample passed through a sieve of 40 meshes to the inch. The ilmenite cannot be detected by the microscope, as in the titaniferous ores of the Adirondacks, nor can it be magnetically separated, as in the titaniferous ore of Natashkwan, Canada. To all appearances it is a chemical compound of the double oxides of iron and titanium and not a mechanical mixture, as is the ore of the Adirondack deposits.

Jan 8, 1920

By Alan Morris

Season cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes arc fairly well understood and means for its prevention are inexpensive and effective, so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,' in discussing a paper by Hatfield and Thirkell, says: " He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultaneous corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack. Dr. McAdam3 has investigated the effect of corrosion on the fatigue limit of brasses, among other materials. He directed a stream of either fresh or salt water against the specimen while it was undergoing fatigue test. The corrosion-fatigue limits thus determined may be considerably lower than the endurance limit without coincident corrosion. The exact

Jan 1, 1930

By G. E. Agar, P. L. De Bruyn

Flotation is an important example of a chemical process by which one solid may be separated from other solids in a mixture. In contrast to other chemical processes such as leaching and smelting, separation of solids by flotation is characterized by the establishment of contact among three phases. In froth flotation these three phases are the solid to be floated, an aqueous electrolyte solution, and a gas, usually air. The gaseous phase may be re- placed by an organic liquid phase or this organic liquid phase may be added deliberately as a fourth phase. To gain an understanding of the flotation sys- tem, it is therefore necessary to study the chemical and physical properties of surfaces and to establish the effect of changes in composition of the bulk phases on the nature of the three interfaces, solid-gas, solid-liquid and liquid- gas. With very few exceptions inorganic solids are completely wetted by the aqueous phase so that the first step in flotation is to replace partially the solid-liquid interface by a solid-gas interface. This displacement process is accomplished by the addition of suitable reagents to the aqueous phase. The resultant surface reaction leaves the solid surface with a hydrophobic film. Although the primary objective of these reagent additions is to alter the solid surface, chemical reactions between the added chemical species and those species derived from the dissolution of the solids are unavoidable. For a quantitative description of such reactions and for the determination of the feasibility of a proposed reaction, we rely on available thermodynamic data. The application of thermodynamic principles to flotation systems has contributed much to our understanding of flotation. The changes in thermodynamic properties such as free energy and chemical potential are accessible to experimental determination, and a knowledge of their magnitude allows us to develop and predict a chemical mechanism oy which a solid becomes floatable. In this chapter it will be assumed that the reader has a working knowledge of the general principles of thermodynamics and solution chemistry. A complete discussion of the physical chemistry of flotation must include a treatment of solubility relations, complex ionic equilibria, reaction potential, and the elements of electrochemistry, especially those dealing with reversible electrical cells. The principles related to all of these features of the flotation system will not be discussed in this chapter. The discussion will be concerned with the thermodynamics and electrochemistry of surfaces and the electrical double layer model of the interface.

Jan 1, 1962

By H. L. Stone, A. O. Garder

A numerical method of solving the partial differential equations which describe the one-dimensional displacement of oil by gas has been presented. Possible extension of the method to treat multidimensional flow is discussed, and the limitations of this extension are indicated. Using this method, it is possible to allow for the existence of a gas cap, the presence of any number of gas-injection or oil-production wells and the evolution of dissolved gas from the oil. It is also possible to allow for variation in the cross-sectional area, elevation, porosity and permeability of the reservoir. The influence of relative permeability and the force of gravity in the direction of flow upon the displacement is considered. The influence of capillary pressure upon the flow and the effect of gravity in the direction perpendicular to flow are neglected. The physical properties 01 the fluids are considered to be Junctions of pressure only, and equilibrium between contiguous phases is assumed. The numerical calculations can be readily carried out by the use of a digital computer. Several example analyses have been performed using the IBM 704 computer, and about one-third of an hour of computing time was required per case. Reservoir behavior predicted by use of this numerical method was compared to data obtained by other methods for three cases — complete pressure maintenance, dissolved-gas drive and gas-cap drive. The independent solutions to these problems were obtained by analytical solution, laboratory experiment and field data, respectively. Agreement of the numerical solution with data from these sources was good; this agreement establishes the convergence and accuracy of the numerical method. INTRODUCTION Most petroleum reservoirs can be produced by any one of several alternative programs. When a reservoir is produced by primary methods, production economics can be influenced by controlling the number and location of wells and the flow rate of each well. An even greater influence may be achieved by augmenting the recovery of oil obtainable by primary methods. This can be accomplished by injection of fluids such as water, natural or enriched gas or a bank of light liquid hydrocarbons. Selection of the most desirable operation requires a means of predicting the reservoir behavior which will result from each of the several alternative programs. The purpose of this paper is to present a mathematical method for predicting the behavior of reservoirs produced by gas-cap drive, dissolved-gas drive or pressure maintenance by gas injection. The method described herein takes cognizance of phase changes caused by a decline or an increase (due to gas injection) in reservoir pressure, of the presence of a gas cap and of the effect of gravity on the flow of gas and oil. Relative permeability relationships are used to define the flow properties of the rock. Allowance is made for variation in cross-sectional area, elevation, permeability and porosity of the reservoir. Both the influence of capillary pressure upon the flow and pressure gradients in the gas cap are neglected. Whenever a liquid phase and a gas phase are in contact, they are assumed to be in equilibrium. The physical properties of the fluids are considered to be functions of pressure only. Therefore, if the method is to be used to predict the effects of a gas-injection program, mixtures of the injected gas and formation crude should-have the same physical properties as mixtures of formation gas and crude. The equations to be presented in this paper apply only to a one-dimensional case; therefore, they neglect the influence of gravity in the direction transverse to the flow. As is well known, this gravitational influence may lead to overriding of oil by gas. Consequently, this procedure as presented is most applicable to long, thin reservoirs for which gravity overriding is not important. On the other hand, the equations presented can be generalized to treat multidimensional flow and, hence, to consider gravity overriding, if desired. A word of caution on two points is advisable here, however. First, the authors have not demonstrated the accuracy of the numerical technique for multidimensional flow. Second, and more important, capillary pressure will often be of importance in multidimensional problems. Obviously, in such cases a generalization of the

By Roderick K. Davey

Introduction in any business, it is essential that we select those alternatives which are not only technically feasible, but will be the most profitable to the business m terms of corporate objectives Some of the studies and activities requiring support of financial analysis to select the alternatives which most closely satisfy the management objectives and technical considerations are as follows 1 ) Cutoff grade determination. 2) Ore reserve estimation. 3) Production forecasts (long- and short-term) for an operating mine, development of a new mine, or expansion of an existing mine. 4) Evaluation of haulage alternatives. 5) Evaluation of equipment.

Jan 1, 1979

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The-Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend .a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and. assurance is given that most careful service will be rendered to them.

Jan 6, 1915

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940