Search Documents

By AIME AIME

C. H. BENEDICT, chief metallurgist of the Calumet and Hecla Consolidated Copper Co., has pioneered for nearly half a century. Noted for his ammonia leaching process, lie has Iong been responsible for all Calumet and Hecla mill, concentrator, and reclaination plant flowsheets. His influence has spread far beyond his own organization. lie is dean of Lake Superior metallurgists and has contributed greatly toward raising his specialty-the country over-to an honored profession; not merely an honored profession but a profitable one for industry and the public. The leaching process which he developed in 1912 has, since 1915, produced for Calumet and Hecla 250,000 tons of copper from waste tailings at a cost per pound, in 1929, below five cents. It has yielded profits of $35,000,000. In the war just ended, this process proved the only one adaptable to the recovery of copper from gilding-metal¬clad steel strip, and Calumet and Hecla treated more than 50,000 tons of such scrap for the Government.

Jan 1, 1945

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in .he discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in he smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently n the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of he joined pieces (base metal). The filler metal, older or braze, is always of lower melting point than the base metal. Consequently with these) recesses there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Joining operations carried out at temperatures above 500°C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used.

Jan 1, 1975

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.' At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir's work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.' Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By John V. Beall

STREAM pollution caused by waste waters from mineral industry operations is a problem that has grown up with the industry. Its importance to each operator is dependent on the amount and type of waste he dumps into the rivers and streams; on whether this waste pollutes the waters sufficiently to make them unfit for potable water, irrigation, and conservation of wild life; and on whether this waste makes a safety or health hazard. Through the years our growing population and industry have made increasing demands on the mineral industries, the suppliers of the raw materials on which our industries are based; and we have met these demands at some sacrifice to the natural beauty and cleanliness of our country. However, that is often the unavoidable nature of the business, and along with the increased use of our

Jan 1, 1948

By Charles Jackson Abrams

MINING is one of the major industries of the Rocky Mountain region and since the United States became involved in the present World War, all mines have been called upon by the Government for the maximum production of the strategic metals necessary. Operating under the most adverse conditions, such as priority requirements, slow delivery of necessary material and equipment, labor shortages, and freezing of all wages, which still permitted some industries to pay higher rates than were allowable in the mines, thereby drawing labor from the mines; and the United States Employment Service continually giving mine labor certificates of availability; these and many other problems made mine operation particularly difficult. Yet, in spite of these obstacles, the mining industry, either through its own resources or through Government subsidies in the form of loans or premium prices for strategic metal, have and still are making an all-out effort to meet Government demands. They, without question, have played a major role in assisting the war effort.

Jan 1, 1945

By John H. Hearding

Induction heating, together with automatically controlled tempering and hardening is giving Oliver faster and more accurate bit sharpening, while experiments with bit taper promise to offer increased footage per bit.

Jan 10, 1953

By E. DeGolyer

WAR has wrought sharp and sudden changes in the pattern of the oil industry. The most obvious and most striking of such changes have been in the fields of transportation and refining. A third of the world's total oil production formerly started to market, tanker-borne, over the waters of the Gulf and Caribbean. Most of this oil went to our North Atlantic ports, supply points for the world's greatest consuming center. This tremendous traffic, disrupted by the loss of tankers as a result of requisition for military purposes and by the activity of enemy submarines, has had to be substituted largely by such lines of supply as could be improvised without loss of too much time. No single solution for this gigantic problem has been found nor is it likely to be entirely solved for some time to come. It has been solved in part, however, by rearrangement, reversals, and patching up of existing pipe-line systems; by overland transport of crude and products in tank cars on a scale never before attempted; by barging over inland waterways; and through the construction at long last of the "big-inch" line, the first leg of which is just being put into operation as far as Norris City, III. The tank-car traffic alone, reaching a peak of deliveries of 856,710 barrels per day into District 1 during the week ending Sept. 19, 1942, and accomplished at an expense of millions of dollars in extraordinary transportation costs, defrayed by the Defense Supply Corp. and by the mobilization of tank cars from all over the nation, is a story worth the telling but by some of those who directed it.

Jan 1, 1943

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By Randall L. Neal

This paper discusses the impact of taxes at the state and federal level on typical on-shore oil and gas exploration economics in the USA. Taxes considered are the windfall profits excise tax, state production (or severance) taxes, state income tax, and federal income tax. Also considered will be market prices for oil and gas in the USA. The effect of government take as a percent of revenue, on rate of return, discounted Payout, and discounted cumulative cash flow is shown on the attached tables. The conclusion drawn is that tax laws, while rarely the most important factor to be considered when drilling a well, can have significant impact on the profitability of oil and gas ventures, and should be considered when determining where to drill. Hypothetical exploration wells were analyzed for the impact of tax laws on project profitability. The results of this study show that when factors other than taxes are postulated to be the same (such as producing rate, capital, operating costs, and prices), cash flow can vary by as much as 68% due to the differences in the tax laws. Other significant findings for the cases studied include: (a) that discounted payout varied by as much as 1.8 years, (b) that rate of return differed by up to 67% and (c) the total tax rate as a percentage of revenue had a maximum variance of 33%.

Jan 1, 1982

References are in all cases to the earliest known editions. In the few cases where the first edition has been unavailable for consultation, the particular one studied is indicated. English translations are included when known, but not others. [ ]

Jan 1, 1942

Executive SIDNEY J. JENNINGS, Chairman GEORGE D.-BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman. CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 9, 1918

By L. R. Plitt, E. O. Lilge

Tests carried out with both kaolin and silica slurries show that flocculants of the polyacrylamide type can be used to improve the thickening performance of hydrocyclones. This thickening improvement demonstrates that contrary to previously held theories, flocs can be formed which are capable of resisting the shear forces in a hydrocyclone. For the 1.25-in.-diam cyclone used, optimum thickening occurs when the flocculant solution is injected into the slurry stream at or near the feed inlet. Hydrocyclones offer many distinct advantages over gravity thickeners. These advantages include simplicity, low initial and operating costs, small space requirements, and flexibility of operation. In spite of these advantages hydrocyclones have not been widely used as thickeners. The main reason for their lack of application is that hydrocyclones are unable to efficiently remove semicolloidal particles (less than 5 microns) from the suspending solution. In gravity thickeners, the fine particles can be induced to form particle aggregates, or flocs, which have the settling characteristics of large particles. In the hydrocyclone, however, it was always assumed that the existence of shear would prevent the formation of flocs.1-3 Thus, if no floc structure is retained, the thickening hydrocyclone must be designed so that its separation size is below the size of the smallest particle to be recovered. To obtain a very small separation size requires the formation of very high centrifugal forces, which necessitates the use of small-diameter cyclones. Small hydrocyclones have, in turn, very low throughput capacities which render them impractical for many industrial thickening applications. Thus, if the effects of flocculation cannot be utilized, the usefulness of hydrocyclones as thickeners remains limited to pulps which contain no very fine particles. It is well established that most substances acquire a surface electric charge when brought into contact with an aqueous medium. The repulsive interactions between similarly charged particles act to prevent flocculation. One method of flocculating a dispersion is to neutralize the repulsive surface charges by the addition of an electrolyte. The reduction of the electrostatic surface charge (Zeta potential) then permits the universal van der Waals attractive forces to operate between the atoms of the various particles and form particle aggregates. The lime additions used by thickener operators promotes flocculation by this mechanism. A second method of flocculating a dispersion is by the addition of long-chain macromolecules. In this case flocculation is brought about by a bridging mechanism in which the molecules are adsorbed with part of their length on two or more particles, thus forming a molecular bridge between the particles.4,5 The molecules also form bridges between themselves when a single particle is bonded to several polymer molecules. The type of bonding between the flocculant molecule and the particle may be hydrogen bonding, chemical bonding, or electrolytic attraction.6 The flour and glue which are used as thickener additives are believed to promote flocculation in this manner. In the past decade synthetic long-chain polymers with extremely high flocculating capabilities have been developed. The flocs formed by these new polymeric flocculants are larger and more shear-resistant than those formed by the presence of electrolytes.7 The advent of these flocculants raises the question: Are the flocs formed by these synthetic polymers stable enough to resist the liquid shearing forces in a hydrocyclone? The investigations reported in this paper were carried out in order to provide some answers to this question. EXPERIMENTAL WORK For the bulk of the test work a 5% slurry of commercially available kaolin with an average particle size of 5 microns was used. An initial evaluation of the available flocculants was carried out to determine which flocculant formed the most shear-resistant flocs. A combination of the techniques used by Healy7 and Booth8 was used for this purpose. This initial study revealed that the neutral high-molecular weight polyacrylamides produced the most shear-resistant flocs. One of these flocculants, Separan MGL*, was selected and then used for all the hydrocyclone tests. The flocculant was dissolved in water and added to the hydrocyclone as a dilute solution.

Jan 1, 1968

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 11, 1918

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT-M. RAYMOND Membership LEWIS W. FRANCIS KARL EILERS, Chairman J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY.1 Chairman. ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 2, 1919

INTERNATIONAL GEOLOGICAL CONGRESS. (For further particulars apply to the Secretary, 12th International Geological Congress, Victoria Memorial Museum, Ottawa, Canada ; cable address, Geocong, Ottawa.) The Coal Resources of the World.-Three quarto volumes of about 400 pages each, 8 1/4 by 10 3/4 in., and an atlas of about 70 maps in colors, 13 1/3 by 19 1/2 in., bound in heavy paper cover. Edition limited to 3,000 copies, One thousand copies will be reserved for members of the International Geological Congress, and the remainder of the edition will be distributed in the order in which applications are received. Price, $35 per set. Ready in July, 1913. This book is an inquiry made upon the initiative of the Executive Committee of the Twelfth International Geological Congress, with the assistance of geological surveys and mining geologists of different countries, published by: Morang & Co., Ltd., Toronto, Canada. Headquarters During Session at Toronto. The headquarters will be a t the University of Toronto, where there will be a branch post-office open at all hours and at which registered mail may be received or despatched, money orders sent or cashed, etc. A hank will be established at which money may be exchanged. A typewriting service will be maintained, also a telephone service and messenger service. Railway and steamship agents will also be in attendance. A restaurant service providing luncheon in the middle of the day will be arranged.

Jan 8, 1913

By Randall J. Essex

A massive mudslide blocked a river in Utah, impounding a 61 m (200 ft) deep lake. Under emergency conditions, a system was designed and constructed to: (1) drain the impounded lake; and (2) provide a permanent diversion for the river around the mudslide. The system consisted of a low level tunnel, a connecting vertical shaft daylighting close to the lake shore, control valves mounted within the tunnel, and an inlet channel between the lake and the shaft. This paper focuses on the problems and concerns surrounding the inlet channel excavation and the stabilization of the remaining vertical rock walls.

Jan 1, 1984

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By Edwin Ludlow

T HE OPEN FORUM on this subject called by Mr. Hoover at the recent meeting of the Institute' brought out a large number of very able papers, and a very full discussion of all the problems involved. The criticisms of the bituminous industry were: 1. That it was over-developed with the possible output nearly 50 per cent. in excess of the present requirements; that during the summer there were plenty of cars and no orders, and during the winter there were plenty of orders but no cars. 2. That the mines were not properly developed from an engineering standpoint, and that the recovery of the coal varies from 50 per cent. to 95 per cent. 3. That this industry, employing over 600,000 men, could, if running full time, release 100,000 men for other work. 4. That the studies made by the engineers of the Fuel Administration showed that the cost of production increased with a loss of time and that with a 50 per cent. operation the increase in cost was about 40 per cent.

Jan 1, 1920

By W. C. Hazen, A. V. Henrickson

URANIUM plant operations of the Kerr-McGee Oil Industries at Shiprock, N. M., began in December 1954. As originally designed, the plant treated Plateau carnotite ores by the acid cure process, which dissolved both uranium and vanadium minerals. After 16 hr of acid curing, the ore was conveyed to an agitator and leached for 2 hr in acid liquor at a pH of 1.0. The leach pulp was then separated at 100 mesh in a classifier, the sands continuing through a washing classifier circuit and the slimes going to a countercurrent decantation system of four thickeners.

Jan 9, 1957