Search Documents

Jan 1, 1934

By Donald C. Moore

INTRODUCTION Published laboratory procedures used by the major crusher manufacturers for estimating crusher size are based upon techniques developed in the mid 1940's. Specifically, the two largest U.S. crusher manufacturers are using the Bond impact procedure. Although the procedure is still in use, there is little confidence in the results. Unless the laboratory results fall within a preconceived range, personal experience is used for selecting the number of crushers and connected horsepower (Coleman, 1978). There have been numerous theoretical studies of the communition of particles. However, no procedure has been widely acclaimed for predicting crusher power requirements. Experimental studies have included breakage by slow compression, slow speed impact and high speed impact. Theoretical results have increased our knowledge of the comminution process, but the procedures have not been capable of analyzing the complex mechanism of industrial crushing machines. The purpose of this chapter is to review the empirical crushing procedures that have been used, including advantages and disadvantages. A new procedure which has been in development at Allis-Chalmers Corp. from 1977 to 1982 is detailed. Actual results of the new procedure on a concentrator feasibility study are included. EXPERIMENTAL GOALS The goals of a laboratory crushability procedure are accurate predictions of: (1) Rock crushability, measured as energy per unit mass. (2) Crusher product size analysis. A procedure capable of predicting these parameters should be inexpensive and require a minimum amount of sample. CRUSHABILITY TESTS Bond Impact Procedure F. C. Bond (1946) detailed the development of the pendulum impact device that is still used by the leading crusher manufacturers (Bond; Rexnord, 1976). The device (Fig. 1) is comprised of two bicycle wheels with 13.6 kg steel hammers tangentially attached to the rims. The hammer faces are 50 mm apart at rest. On opposite ends of the hammers lifting

Jan 1, 1982

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By W. T. Read, W. Shockley

THE subject of this chapter is the application of the dislocation theory to two problems of physical metallurgy where the theory has been able to give definite predictions that subsequently have been verified by experimental observations. Much of the history of dislocation theory has consisted of the explanation of already established results on the basis of ad hoc assumptions. Scattered bits of fundamental theory were formulated as needed-in particular explanations. The result had the appearance of a hodgepodge of ingenious ideas and exciting but possibly artificial speculations. The review article by Koehler and Seitz in this volume gives an excellent picture of the breadth, diversity, and flexibility that have made dislocation theory attractive to speculative theorists, although occasionally bewildering to others. Since 1950, there have been two developments, which have helped to establish dislocation theory, on the one hand, as a systematic coherent body of theory and, on the other, as a means of making predictions that can be tested experimentally and thereby guide experiment into more fruitful channels. The first and easier of these developments has been the systematic derivation of the classes and properties of dislocations from fundamental crystallographic concepts. An example of one phase of this development is the rigorous treatment of

Jan 1, 1954

Jan 1, 1948

Jan 1, 1922

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By A. W. Ambrose, C. E. Beecher

It is the purpose of this paper to summarize data on unitization projects in Oklahoma and Kansas as obtained from replies to questionnaires sent out by the A. I. M. E. committee for these states. The information received indicates that unitization is growing rapidly in this area, but has not been in operation for a sufficient length of time to develop production history. It was impossible to obtain a record of all unitization projects in the time available. The magnitude of such projects is indicated by the fact that reports were received covering a total of 171,420 acres in Kansas and 49,350 acres in Oklahoma. Most of these units have been formed during the past 2 years, the greater number having been completed in 1929. It is anticipated that even more will be formed during the present year. The following important facts have been emphasized by answers to the questionnaire and discussion with various operators: 1. Unitization is growing rapidly, as evidenced by the number of units and the large total acreage now included in units as compared with practically no acreage 2 years ago. 2. Operators are convinced that unitization is reducing development and operating cost and they anticipate greater reductions as experience is gained in unit operation. 3. Producing units have not been in operation for a sufficient length of time to give significant production history from which to estimate the ultimate recovery of oil, but the general opinion seems to be that more oil will be recovered. 4. In view of the benefits to be derived from unitization, many operators are refusing to carry on wildcat operations unless a unit has been formed. If this attitude continues to grow there will be no large pools developed in Oklahoma and Kansas in the future except under unit control. Summary The following tabulation gives a condensed summary of the information received on unit operations in Oklahoma and Kansas, but does not include all units, because many were not reported.

Jan 1, 1930

By E. H. Crabtree, Neil S. Parker

THE custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or four concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to 1/2-in. size in a 3-ft Symons shorthead crusher. After crushing to 1/2-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, to pct and 5 pct of its feed. After No. 1 sampler, the material passes through a mixing barrel and is then crushed to 1/4-in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to too tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex Highweir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fagergrens. Copper-lead differential separation

Jan 1, 1947

By Paul A. Beck, John Towers, W. D. Manly

Recent work on grain growth in high purity aluminum and in a solid solution type alloy of aluminum and magnesium1 showed that the isothermal increase of the average grain diameter D with time follows the equation D = K(tg + A)2 Eq 1 Here tg is that portion of the total annealing time 1, which is available for grain growth, that is the annealing time less the time necessary for complete recrystallization. The parameters A and n depend only on the temperature. A has the dimension of time, and is usually of the same order of magnitude as the time for recrystallization: R. In some instances R may be substituted for A in Eq I. This is the case for example at long periods of annealing or at high temperatures, where both A and R become small in comparison with t. In such instances Eq I is simplified to D = K, tn Eq 2 For high purity aluminum the exponent n increases in the ratio of about I to 5 in. the temperature range of 350' to 6w°C. 70-30 brass has been long known to exhibit grain growth of the continuous type, such as occurs in pure metals. For this reason, it was of interest to determine whether grain growth in brass also follows Eq I and 2 as it does in aluminum. Isotherma1 grain growth data for 70-30 brass were published in recent years by R. S. French2 and by H. L. Walker.' Fig I shows a log D vs. log t plot of French's data, together with the 500, 600 and 700°C data by Walker for 42.8 pct reduction by rolling. In such a log D vs. log t plot Eq 2 corresponds to a straight line with a slope of n. As seen in Fig I, the data of French and the 600°C data of Walker can be represented by straight lines. However, the 500 and 7c0°C data of Walker give curved lines and the average slope of his 500°C line is very different from the slope of the line representing French's data for the same temperature. Furthermore the curvature of the 700°C line suggests a tendency for grain growth to stop after 8 hr. If confirmed, this would constitute a definite deviation from Eq 2, not explainable on the basis of the specimen thickness effect found in high purity aluminum.' Walker's specimens were 0.125 in., or 3.18 mm thick, while the deviation occurs at a grain size of approximately 0.4 mm. A further point of divergence arose recently, when J. E. Burke suggested4 on the basis of Walker's data, that, instead of Eq 2, grain growth in 70-30 brass follows the equation D - D, = K . tgn Eq 3 Here D, is the grain size as recrystallized at the temperature in question. Although it was possible to show5 that, for pure aluminum, for which isothermal grain growth has been carefully investigated, Eq 3 is incompatible with the experimental facts, the situation remained somewhat obscure with respect to 70-30 brass. In view of the discrepancies between the published data on brass from different

Jan 1, 1949

By John Towers, Paul A. Beck, W. D. Manly

Recent work on grain growth in high purity aluminum and in a solid solution type alloy of aluminum and magnesium1 showed that the isothermal increase of the average grain diameter D with time follows the equation D = K(tg + A)2 Eq 1 Here tg is that portion of the total annealing time 1, which is available for grain growth, that is the annealing time less the time necessary for complete recrystallization. The parameters A and n depend only on the temperature. A has the dimension of time, and is usually of the same order of magnitude as the time for recrystallization: R. In some instances R may be substituted for A in Eq I. This is the case for example at long periods of annealing or at high temperatures, where both A and R become small in comparison with t. In such instances Eq I is simplified to D = K, tn Eq 2 For high purity aluminum the exponent n increases in the ratio of about I to 5 in. the temperature range of 350' to 6w°C. 70-30 brass has been long known to exhibit grain growth of the continuous type, such as occurs in pure metals. For this reason, it was of interest to determine whether grain growth in brass also follows Eq I and 2 as it does in aluminum. Isotherma1 grain growth data for 70-30 brass were published in recent years by R. S. French2 and by H. L. Walker.' Fig I shows a log D vs. log t plot of French's data, together with the 500, 600 and 700°C data by Walker for 42.8 pct reduction by rolling. In such a log D vs. log t plot Eq 2 corresponds to a straight line with a slope of n. As seen in Fig I, the data of French and the 600°C data of Walker can be represented by straight lines. However, the 500 and 7c0°C data of Walker give curved lines and the average slope of his 500°C line is very different from the slope of the line representing French's data for the same temperature. Furthermore the curvature of the 700°C line suggests a tendency for grain growth to stop after 8 hr. If confirmed, this would constitute a definite deviation from Eq 2, not explainable on the basis of the specimen thickness effect found in high purity aluminum.' Walker's specimens were 0.125 in., or 3.18 mm thick, while the deviation occurs at a grain size of approximately 0.4 mm. A further point of divergence arose recently, when J. E. Burke suggested4 on the basis of Walker's data, that, instead of Eq 2, grain growth in 70-30 brass follows the equation D - D, = K . tgn Eq 3 Here D, is the grain size as recrystallized at the temperature in question. Although it was possible to show5 that, for pure aluminum, for which isothermal grain growth has been carefully investigated, Eq 3 is incompatible with the experimental facts, the situation remained somewhat obscure with respect to 70-30 brass. In view of the discrepancies between the published data on brass from different

Jan 1, 1949

Jan 1, 1925

(Members are urged to send in for, this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Aug. 10 to Sept. 10, 1915: Everett L. Booth, New York, N. Y. Raymond B. Ladoo, Cambridge, Mass. T. E. Sturtevant, Dover, N. J. Henry A. Tobelman, Ajo, Ariz. C. A: Filteau, New York, N. Y. R. B.Tinsley, B. Tinsley; Venezuela. Guy C. Riddell, Helena; Mont. ; E. H. Hamilton, Norfolk, Va. Joseph Leiner, New. York; N. Y. M. Yoshimura, Tokyo, Japan. Alfred W. G. Wilson, Ottawa, Canada. Van H. Manning has been appointed Director of the U.. S., Bureau of Mines, to succeed the, late, Dr. Joseph A. Holmes. Mr. Manning was Assistant Director of the Bureau. 0. M. Lewyn, formerly Mine. Superintendent for the Braden Copper Co., has accepted the position of Assistant Mine Manager with the Union Minière de Haut Katanga of South Africa.

Jan 10, 1915

By W. Kane, M. Karmis

Roof and rib failures in underground coal mines are one of the major problems facing the industry today. In addition to safety considerations, the resulting economic impact of such failures is staggering. Uncovering and replacing buried and damaged equipment and clearing entries can account for a large expenditure in lost man-hours and machinery. Yet, because of the complex nature of its formation, geological variability, and structural characteristics, coal mine roof strata is one of the least controlable of all mine design parameters. This is especially true along the leading (southeastern) edge of the Appalachian coalfields where considerable faulting and movement has contributed to hazardous coal mining roof conditions. During this research, a detailed study of several mines, in the southern Appalachian coalfields, was undertaken to determine the most prominent geomechanical factors affecting roof stability and to evaluate their influence in promoting unstable ground conditions. In order to accomplish this task, the major geological and geomechanical features found to be detrimental to coal mine roof within the Appalachian basin were identified and mapped in four Virginia mines. Statistical processing by chi-square and regression analysis was used to determine the influence of geology, mine-layout, and support methods on roof stability. It was found that some easily determined parameters can be successfully used to predict potentially unstable areas. A simplified roof classification system was developed based on these geomechanical parameters, which can be used to assess the stability of a particular roof type. A roof rating index was also devised capable' of expressing the probability of a failure under a given set geomechanical condition.

Jan 1, 1984

S., at Niagara Falls, as an expert chemist. There he was engaged in perfect.ing the various kinds of gases, and while thus employed was gassed several times, which so affected his heart and lungs that he was unable to withstand an attack of the influenza which developed into pneumonia, from which he died at the end of 24 hours. He was a member of St. Luke's Episcopal Church, Lebanon, and belonged to the Ancient Accepted Scottish Rite of Freemasonry, Lebanon Lodge 121, I. 0. 0. F. and Camp 65, P. 0. S. of A. Lieutenant Bernhardt Edward Heine Bernhardt Edward Heine, a lieutenant in the Aviation Service of the U. S. Army, died as the result of a fa1I1 in an aeroplane at Fort Sill, Okla., on Aug. 10, 1918. The accident occurred on Aug. 2, when the machine in which he was flying with Lieutenant Carsons fell from a height of 1500 ft.; Lieutenant Carsons was instantly killed, but Lieutenant Heine died from his injuries a week later. Lieutenant Heine was born at Mount Clemens, Mich., in 1895. After attending the local High School he entered the Michigan College of Mines, and became a Junior Member of the Institute while still a student. He graduated in 1916, with the degree of B. S. In 1914 he served as a transitman for the engineering department of the City of Hancock, Mich. Lieutenant Heine had been in the army since 1916, having been with the 'troops at 'the Mexican border. He had been in the Aviation Section since August, 1917.

Jan 1, 1920

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

MINING AND METALLURGICAL SOCIETY OF AMERICA San Francisco Section The San Francisco Section of the Mining and Metallurgical Society of America held a joint meeting with the local section of the American Institute of Mining Engineers at the Engineers' Club, San Francisco, on Tuesday, Apr. 16, 1918. The meeting was preceded by a dinner. Letters from the parent body in NewYork asking for the consideration of the proposed bill before Congress, and an expression of opinion relative to the appointment of a Federal Administrator of Mines justified the joint meeting of the local sections of the two mining societies, in that a more representative opinion of the engineers of California could he obtained. The meeting was called to order at 7:15 P.M. by Mr. Frank H. Probert acting as Chairman. About thirty engineers were present. Mr. Probert read a letter of March 14, from Secretary Huntoon, asking that the meeting be called. He read excerpts from Bulletin 117 of February 28, 1918, of the Mining and Metallurgical Society containing a copy of the proposed bill, so that all present might be advised of its essential contents. He briefly commented on the urgent need of such legislation and invited discussion of the subject. After long and thorough discussion on the part of the members present, Professor Lawson made the following motion: I move that a resolution expressing the sense of the joint meeting of the local sections of the American Institute of Mining Engineers and Mining and Metallurgical Society of America be forwarded to the secretaries of the two societies to the effect that we heartily approve of the purpose and intention of the bill designed to promote and stimulate the production of minerals necessary for the successful prosecution of the war; and that we suggest prices should be fixed for the period of the war and two years thereafter, and that these prices, guaranteed by the Government, should apply at the nearest shipping point to place of production of the minerals. This motion was carried. The meeting then adjourned, and a telegram was sent by Mr. Probert, the Chairman, to Mr. Huntoon, notifying him of the motion that had been carried at the meeting.

Jan 7, 1918

By F. Wartenweiler

Much has been written on milling and cyanidation as practiced on this gold field, therefore the purpose of this paper is to record its development only briefly and to describe in more detail the contemporary state of the science and art of this branch of metallurgy. It is a pleasing task, because a steady evolution is to be recorded. Definite trends influenced the development. Some have the stamp of original thought and observation; many have been achieved from a logical sequence of planned experimentation and research; while others have resulted from the drive of sheer necessity. The large scale of operations and capital outlay has compelled conservative progress. Banket ORe For a better understanding, a review of the characteristics of the ore may not be out of place. The Witwatersrand gold ore is named "banket" from the similarity of the oxidized outcrop ore to the Boer almond cake of that name. The inter bedded orebody is commonly called "reef." It is a conglomerate composed of various sizes of pebbles, principally non-gold-bearing white quartz, which constitute about 70 per cent of the bulk, within a matrix of cementing material consisting of fine-grained quartz, sericite, chlorite and chloritoid and containing the precious metals and mineral sulfides. Argillaceous components in the mil pulp may be as high as 32 per cent. Of the sulfide minerals, pyrite and pyrrhotite are predominant. Most base-metal sulfides are present, but sporadically and generally only found in highly concentrated mill products. In the latter, osmiridium is recovered in varying amounts; from 1 oz. in 3000 tons to 1 oz. in 10,000 tons of ore. Most of the oxidized ore has been mined, so milling is confined principally to the sulfide ore. A typical analysis of sulfide ore is: silica (SiO2), 86.76 per cent; pyritc (FeS2), 2.75; ferric oxide (Fe2o3), 2.65; alumina (Al2o3), 6.91; lime (CaO), tr.; magnesia (MgO), 0.70; sp. gr., 2.7. Milling grade at present price of gold (137 shillings per ounce) varies from 3.5 to 8.5 dwt., with one mine milling ore as high as 16 dwt. The

Jan 1, 1935

By Brandon H. Grove

In Austria's only producing field, at Zistersdorf, Erdoel Produktions-gesellschaft completed a single new producer, its well Gosting 6 coming in early in October for an average production of about 15 tons daily. For further testing within the proved part of the field this company's Gosting 7 was at the close of the year drilling in Pannonian strata at 760 m., and its Gosting 8 was rigging up. Outside of the proved area of the Zistersdorf field two further tests located on the Steinberg dome failed to find production in the known oil-bearing strata of the Sarmatian, and were deepened as wildcats into the Cretaceous Flysch. The first of these, Neusiedel 1, about one kilometer north of the known producing area, found oil in the Flysch beds at a depth of 1290 m. for an initial production of about 10 tons per day. The second test, Windisch Baumgarten la, is an old well previously considered a failure, which when deepened achieved a production of about 5 tons per day in the Flysch Inoceramus beds at 985 m. Neither of the foregoing wells is producing from a stratigraphically definable horizon, oil accumulation in the Flysch of this area being apparently controlled by tectonic breccias or related crevices.

Jan 1, 1937

By R. V. Norris

THE wage rates and working conditions in the anthracite. region of Pennsylvania have been governed for nearly 20 years by the award of the Anthracite Coal Strike Commission, appointed Oct. 16, 1902, by President Roosevelt. The report of this com-mission, made in March, 1903, was accepted and, with eight modifications made at various dates, has had .almost the force of law, and has kept this great indus-trial region free from strikes for almost a generation. In 1920, President Wilson appointed an Anthracite Coal Commission, and its report, accepted Aug. 30, 1920, governed wage conditions to April 1, 1922. Actually, the agreements have been for terms of two to four years, and lately, in 1916 and 1920, the employ-ees have continued at work pending the negotiation of new agreements which were made retroactive, and which have all been modifications of the original 1903 award. With the expiration, April 1, 1922, of the 1920 award approaching, Mr. Lewis, president, of the United Mine Workers of America, addressed a letter, on Feb. 20, to the operators, suggesting a meeting on March 15; this date was accepted by the latter, with the notation that the time was short. At the meeting, the Mine Workers presented 19 demands, and advised that if a satisfactory agreement was not reached by April 1.a suspension of mining would occur, contrary to the practice since 1916 of continuing work with a retro-active adjustment.

Jan 6, 1922