Search Documents

By F. F. Colcord

THE electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years; and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the, composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. EFFECT OF COPPER CONTENT ON CONDUCTIVITY The first work, was to determine the specific conductivity of silver nitrate and copper nitrate solution. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was, then determined. The plotted results are shown in Fig. 1 and 2. The effect of increasing quantities of silver and, copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 50 g. per liter, as its

Jan 2, 1926

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

The results of a preliminary study of 113 ternary titanium-base alloys are described. The compositions investigated were as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships for these alloys were determined. THIS is the second in a series of papers describing some of the results of the exploratory work on titanium alloys being conducted at Battelle Memorial Institute for the Wright-Patterson Air Force Base. The work with the binary alloy systems has been described in a previous publication.' This paper describes ternary titanium-base alloys as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. As the preparation and fabrication of the 0.5-Ib experimental titanium alloy ingots to 14-ga sheet, as well as the methods of testing used in this work, have been described in the first paper of this series, Titanium Binary Alloys, no further discussion of these techniques will be given. Ternary Alloys Containing Carbon The following alloys of titanium, containing carbon and one other metal, were investigated: 1. 0.25 pct carbon; 1, 2.5, and 5 pct copper. 2. 0.25 pct carbon; 1, 2, and 3 pct silicon. 3. 0.25 pct carbon; 1, 2.5, and 5 pct vanadium. 4. 0.25 pct carbon; 2.5, 3.5, 5, 10, and 15 pct chromium. 5. 0.5 pct carbon; 2.5, 3.5, and 5 pct chromium. 6. 0.25 pct carbon; 1, 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 7. 0.5 pct carbon; 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 8. 0.25 pct carbon; 0.25, 0.5, 1, and 2 pct iron. 9. 0.25 pct carbon; 1, 2, and 3 pct cobalt.

Jan 1, 1951

By Clarence Zener

The heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an understanding will involve two distinct types of inquiry: (I) the direction of the transformation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed herein—steel—such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron-alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data 'being obtained from the simple binary and ternary equilibrium diagrams. Fundamental Equations In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body-centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may. be regarded as filling all the lattice positions of a given type. The introduction of the fundamental the of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1947

By Clarence Zener

The heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an understanding will involve two distinct types of inquiry: (I) the direction of the transformation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed herein—steel—such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron-alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data 'being obtained from the simple binary and ternary equilibrium diagrams. Fundamental Equations In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body-centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may. be regarded as filling all the lattice positions of a given type. The introduction of the fundamental the of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1947

By A. M. Gaudin

Activation of sphalerite with silver ions results from the exchange of two Ag ions for one Zn ion in the sphalerite lattice. The exchange is proportional to the logarithm of time and proceeds until either of the reactants is consumed. Sodium cyanide prevents the activation of sphalerite by controlling the ratio [Zn++]/[Ag+]' in solution. If sphalerite has already been activated with excess silver, cyanide ions can deactivate sphalerite provided oxygen is present. SOLUBLE: silver salts are effective activators for flotation of sphalerite with potassium ethyl xan-thate as collector.* Since sphalerite takes up large quantities of silver ions rapidly,2-4 investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hy-drosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Ii'inally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure. The specific surface of two samples from the 65/100-mesh sphalerite stock, measured by krypton gas adsorption," was 420 cm2 per g. Compared with spheres of the same size and specific gravity, the prepared mineral had five times as much surface. Results of a wet chemical analysis and of a spectro-graphic study are given in Table I. Manganese, nickel, tin, indium, thallium, cobalt, and magnesium were not detected spectrographically. All solutions were preparid by -adding reagent-grade chemicals to conductivitv water. which had been previously saturated with the desired gases. Nitrogen and oxygen were purified, but no attempt was made to purify the laboratory air. Radioanalysis was carried out with prepurified Ag110 tracer obtained from the Oak Ridge National Laboratory. The complete decay scheme for Ae is complex. Its primary emissions are 0.09 and 0.55 mev ß rays and 1.48 mev y raysB and its half-life is believed to be 270 days. In preparation of solutions of AgNO3, the amount of Ag110 added was negligible compared to that of the inert silver. Abstraction of silver from solution by sphalerite was measured after agitation of 1.5 g sphalerite with 20 ml of solution in 50-ml pyrex flasks. All sample preparations were carried out in a dry box so that the proper atmosphere could be maintained. After the mineral had been agitated in the silver nitrate solution, an aliquot of the solution and a sample of the wet mineral were transferred to separate counting vials and weighed. The solid sample was dried and re-weighed and the activity in both vials measured by means of a scintillation counter. With scintillation counting it is possible to count y radiation from the solid and liquid, a distinct advantage over the older ß-ray counting techdiques.4 All measurements of silver activity were made using a sodium-iodide well-type scintillation counter. The amount of zinc in solution was measured colorimet-rically by the monocolor method of Sandell.7 Activation Studies Exchange Between Zinc Ions and Silver Ions During Activation: The increase of Zn++ in solution during activation with Ag+ is shown in Table 11. These data indicate a replacement of one Zn++ by two Ag+. Analysis of a separate two-month agitation test indicated that the replacement of Zn++ by Ag+ was, as expected, in the molar ratio of 2.0.

Jan 1, 1958

By L. Webster Wickes

The bad effects of arsenic in commercial copper are well-known to metallurgists. The refining of copper by electrolysis eliminates practically all of the arsenic, provided certain requirements are fulfilled. The first, and most important, of these requirements is, that the voltage of the depositing current shall not be too high. It has been known for some time that the percentage of arsenic in the deposited copper increases with the voltage. To investigate the relation between the electro-motive force (e.m.f.) and the freedom of the precipitated copper from arsenic, the experiments were made, of which a brief summary is here given: I made three copper-arsenic alloys, containing respectively 3.56, 2.24 and 0.96 per cent. of arsenic. From these alloys I cast several anodes. For cathodes I used sheets of thin copper,

Jan 1, 1905

By Jeffrey L. Thompson, Kenneth A. Gutschick, Robert C. Freas, Robert S. Boynton

Lime, the "versatile chemical," is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or calcia, or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to much confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is usually made from high-calcium or high-magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high-calcium limes contain less than 5% MgO. When the lime is produced from a high-magnesium limestone, the product is referred to as dolomitic lime. Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 A.D. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from a scientific perspective. The production of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 15 to 20 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Calcination refers to a broad class of reactions, of which the lime/limestone reaction is just one, wherein a substance is heated to less than its melting point, resulting in a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [CaCO3 (limestone) + heat (1000° to 1300°C)= 100 CaO (quicklime) + CO2 T 5644 or CaCO3 • MgCO3 (limestone) 10084 + heat (900°C to 1200°C) CaO • MgO (quicklime) + 2CO2 T 56 4088] While there is nearly universal agreement about the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in Fig. 1. From this model it can be seen that calcination is a function of both temperature and CO2 pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the reaction interface must make its way through the lime to the exterior surface. Therefore, because calcination is limited by gas diffusion to the surface of the partially calcined limestone, natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in

Jan 1, 1983

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during February: Paul S. King, Wilmington, Del. William Kelly, Vulcan, Mich. A. Del Mar, South Pasadena, Cal. F. H. Armstrong, Vulcan. Mich. T. D. Babbitt, Nampa, Idaho. Reginald E. More, Toronto, Canada. H. L. Williams, Newtonville, Mass. Tom M. Owen, Broken Hill, Australia. F. W. Bacorn, Pittsburg, Pa. Percy E. Barbour, Candor, N. C. Huntington. Adams, Mexico, D. F. Karl Nibecker, Youngstown, Ohio. Clifton B. Johnson, New. York, N. Y. G. A. Reinhardt, Youngstown, Ohio. W. Spencer Hutchinson, Boston, Mass. Herbert B. Cox, Boston, Mass. F. Louis Grammer, Leesburg, Va. E. C. Pechin, Buchanan, Va. H. C. H. Carpenter, London, England.

Jan 3, 1914

By H. F. Yancey

PHYSICAL properties have been used for a long time in characterizing different kinds of coal, and physical properties, such as friability and slacking, have been included with chemical properties in grouping coals according to the widely used system of classification adopted by the U. S. Geological Survey. Nevertheless, the usefulness of physical properties for classifying the different ranks or kinds of coal has been limited because it has not been possible to express these properties in definite form as numerical values. Because of the present wide interest in the formulation and adoption of a satisfactory system of coal classification, the Northwest Experiment Station of the U. S. Bureau of Mines, in cooperation with the College of Mines of the University of Washington, has recently completed a study of the physical and chemical properties of approximately 100 different coals ranging from lignite to, anthracite. PURPOSE AND SCOPE For this investigation samples were collected in approximately 45 mines and prospects in Washington and 23 mines in other states. The following studies, in addition to proximate and ultimate analyses, were made of the samples: Determination of (1) friability, (2) slacking or weathering characteristics, (3) yield of products by low-temperature carbonization in a laboratory retort, and (4) agglutinating value. Most of the coals examined were subjected to each of the tests enumerated, but with coal of some ranks this was unnecessary in some instances, and in others it was not feasible to do the work involved.

Jan 1, 1932

By Harold Bloom, H. E. Hawkes

Streams and rivers are the principal channels into which the weathering products of rocks and their contained ores are funneled. The inorganic load of a stream system is a crude sample of all the earth materials in the drainage basin of the stream, and the heavy mineral assemblage of sediments is one of the oldest and most successful guides to certain kinds of bedrock ore in unexplored terrain. Early application of this method was made possible by the ease of separation and identification of heavy minerals in the field with the simplest equipment. Water analysis for traces of base metals became a practical possibility about eight years ago with the development of rapid chemical tests that could be carried out at the field site. Since that time the water method has been widely used in mineral reconnaissance, and a substantial number of discoveries have been reported. Here again, the techniques developed for this work were relatively simple and could be performed easily at the field site.

Nov 1, 1956

A New Microscopy and Its Pntentialities. By Charles S. Barrett. (Metals Technology, .April 1945) Physical Metallurgy Fundamental Principles Involved in Segregation in Alloy Castings. By R. M. Brick. (Metals Technology, Sept. 1944) A Stud) of Age-hardening Using the Electron Microscope and Formvar Replicas. By D. Harker and MI J. MurphyI (Metals Technology, June 1945) Standards for Identifying Complex Twin Relationships in Cubic Crystals. By C. G. Dunn. (Metals Technology, April 1945) Orientation Changes during Recrystallization in Silicon Ferrite. By C. G. Dunn (Metals Technology, April 1945) The Orientation Texture at the Surfacr of Cast RIetals. By Gerald Edmunds. (Metals Technology, Jan. 1945) (With discussion) Internal Friction of Single Crystals of Brass, Copper and Aluminum. By George H. Found. (Metals Technology, June 1945) (With discussion) Recrystallization of Aluminum in Terms of the Rate of Nucleation and the Kate of Growth. By W. A. Anderson and R. F. Mehl (Metals Technology, Feb. 1945) (With discussion) Copper and Copper-rich Alloys Textures, Anisotropy and Earing Behavior of Brass. By F. H. Wilson and R. ill. Brick. (Metals Technology, June 1945) (With discussion) Phantom Laminations in Brass. By Daniel R. Hull, H. F. Silliman and John R. Freeman, Jr. (Metals Technology, Jan. 19451 (With discussion) Corrosion of Yellow Brass Pipes in Domestic Hot-water Systems—a Metallographic Study. By E. P. Polushkin and Henry L. Shuldener. (Metals Technology, Oct. 1944) (With discussion) The .Alpha Solid Solution Field of the Copper-manganese-zinc system. By R. S. Dean, J. R. Long, T. R. Graham and .%. H. Robersori. (Metals Technology, June 1945) A White High-manganese Brass. Ry K. S. Dean, J. R. Long, T. R. Graham and C. W. Matthews. (Melds Technology, June 1945) Magnesium Alloys Oxidation Inhibitors in Core-sand Mixtures for Magnesium Castings. By O. Jay Myers. (Metals Technology, Feb. 1945) (With discussion) Grain Size and Properties of Sand-cast Magnesium Alloys. By R. S. Dusk and C. R. Phillips. (Metals Technology, Feb. 1945) (With discussion) Rater Quenching of 'Some Typical Magnesium Casting Alloys. By R. S. Busk and R. E. Anderson (With discussion)

Jan 1, 1945

By C. A. Fisher

THE advent of the Rocky Mountain States into prominence as an oil-producing region is comparatively recent. Scarcely more than a decade has passed since the number of producing oilfields in this part of the country were few and their combined yield small and relatively unimportant. However, oil was discovered and recorded near the present site of Lander, Wyo., as early as 1833 and in 1867, on the comple-tion of the Union Pacific R. R., the site of this oil discovery was located, among other things, as a natural resource of economic importance. In that year a well was drilled for oil, to a depth of 480 ft., near Evanston, Wyo., but later was abandoned. In 1883, the Lander district witnessed the successful completion of the first oil well in the state. In Colorado, oil was first produced from shallow open wells near Canon City and sold to prospectors in 1864; in 1887, the Florence oilfield was discovered and a commercial production developed. While the Rocky Mountain States have never gained the prominence as an oil-producing region attained by the Pacific Coast, Mid-Continent, or Gulf fields, a substantial and increasing production is being taken from the Rocky Mountain province. At the close of 1923, the oil industry in this region has 38 oil and 21 gas fields producing, or capable of producing, oil or gas in a commercial way with a combined annual yield of nearly 47,000,000 bbl. of oil, a daily refining capacity aggregating about 90,000 bbl., upwards of 17,000,000 bbl. of crude in storage, and an 8-in. pipeline, nearing completion, 600 miles long which will connect the most prolific oilfield of the Rocky Mountain States with a trunk pipeline between Mid-Continent and the east at Carrollton, Mo. Several of the larger standard and independent operating companies are now represented in this region and, in the last ten years, there has been developed at Casper one of the large refining centers of the west. Fig. 1 illustrates the rise in production of four of the larger fields, also in the total production of the state; in addition there is given the yield of the larger fields of Wyoming and Montana for 1923.

Jan 3, 1924

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd M.emoria1 Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense.

Jan 1, 1932

By W. V. Vietti, W. A. Oberlin

Crude petroleum produced in the Texas Panhandle oil field is both an asphalt and a paraffin-base oil and is further characterized by being a high-gravity crude with an extremely high cold test,. An eight-well composite of Panhandle crude showed the following characteristics: Gravity, 36.6° A. P. I. Viscosity: 61 sec. Saybolt at 100° F. 170 sec. Saybolt at 75° F. 1560 sec. Saybolt at 50° F. (stirring) Cold Test, 60° F. Distillation Test: Per Cent. Per Cent. Gasoline........................ 28.8 Wax........................... 19.2 Kerosene........................ 4.8 Asphalt........................ 13 .0 Gas oil......................... 30.7 Sulfur1......................... 0.8 Fuel oil......................... 34.7 Subsurface Conditions The original pressure in the formation in the Panhandle field closely approximated 420 Ib. gage or 435 Ib. absolute pressure. Temperatures taken indicate that the formation temperatures do not exceed 90° F. The temperatures in Table I are typical measurements taken on one lease. * A contribrition from the research department of the Marland Refining Co. of Oklahoma and the production engineering department of the Marland Oil Co. of Texas. 1 Smith [Analysis of Panhandle and Rig Lake Crudes. U. S. Bur. Mines, Circular No. 6014 (December, 1926)] found an average sulfur content of 0.6 per cent.

Jan 1, 1928

This fund was established in 1929 for support of research and especially refers to non-ferrous mining and metallurgy. It is administered under the Board by a committee consisting of the President and Secretary and three members selected by the Board. HOWE MEMORIAL LECTURE The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectarers for the years indicated: Albert Sauveur—1924 Bradley Stoughton—1927 John A. Mathews—1925 Henry D. Hibbard—1928 William Campbell—1926 John Howe Hall.—1929 JOINT ACTIVITIES The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers, and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Society This is a corporation organized by the American Institute of Mining Engineers, American Society of Mechanical Engineers, and the American lnstitute of Electrical Engineers, to hold the title and administer the property at 29 West 39th St. In 1916, the American Society of Civil Engineers was admitted, and each society now has an equal one-fourth interest in the ownership, occupancy, and administration of the building. . The cost of this property has been over two million dollars. A. I. M. E. representatives are: Arthur S. Dwight, John V. N. Dorr and H. A. Guess. Alfred U. Flinn, Secretary, 29 West 39th St., New York City. Engineering Foundation This is a fund established by the United Engineering Society in 1915 with a gift of $200,000 from Ambrose Swasey. Subsequent gifts had increased the fund to about $620,000 on March 1, 1929. The income of the fund is used to further research in science and engineering and to advance the profession of engineering and the good of mankind. A research project in alloys of iron is being conducted in

Jan 1, 1929

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great aggregates-preparation plant of the Six Companies, Inc. to supply. construction materials for Boulder Dam&apos; in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con¬tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

AT a luncheon attended by engineering leaders representing every section of the country, Col. Arthur S. Dwight, president of the American Institute of Mining and Metallurgical Engineers, and Charles F. Rand, chairman of the Engineering Foundation, past president of the Insti-tute and its present treasurer, on Thursday, July 20, were decorated with the Croix de Chevalier de la Legion d&apos;Honneur by the French Government for distinguished service in engineering tending to closer and more felici-tous relations between the two countries. The decorations were conferred by Consul General Gaston Liebert. In a speech extolling the war work of the American engineer, M. Liebert declared that Germany had been definitely foiled in her attempt to cripple France industrially for a generation by wrecking the coal mines of northern France. Three-fourths of these mines, M. Liebert said, were in full working order and the remainder will be in complete operation within two years. The Germans thought that it would take from 15 to 20 years to accomplish this. M. Liebert said that reconstruction is going on rapidly in northern France, two-thirds of whose indus-tries are now working. The French Government, he said, is planning water-power improvement on a vast scale, which will soon make unnecessary for France to import a single ton of coal. He urged that French students be sent to America to study engineering. In presenting the decorations, Consul General Liebert eulogized Colonel Dwight and Mr. Rand as personify-ing the spirit and service of the American engineer, which, he said, was a powerful factor in the victory over Germany. He spoke of the growing friendliness between the United States and France and described this ceremony as an epoch in international relations. Calvin W. Rice, secretary of the American Society of Mechanical Engineers, who presided, repeated that international unity among engineers was the dream of Andrew Carnegie, who saw in the efforts of the engineer and the scientist the hope of civilization. Mr. Rice said in part: In the Declaration of Independence occurs the statement that all men are created free and equal. Jefferson was familiar with the writings of Rousseau. In fact, he was a remarkable linguist notwithstanding that he wrote the Declaration of Independence when only 32 years of age. He was one of the very few ambassa-dors in the history of the United States who could speak the language of the country to which they were sent. The interpretation of the passage in the Declaration of Independence is that all men have equal opportunity, not that they are born with equal ability.

Jan 8, 1922