Search Documents

By Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as sand-cast and as heat-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brinell and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. THE demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.1 Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergranular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about-950° F., quenching in oil or in cold or boiling water, and artificially aging

Jan 7, 1925

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-' in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.' The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By Raymond E. Byler

THE challenge of unprecedented need for more metals to meet present-day re-armament and domestic requirements is being met with minerals beneficiation projects of great number and variety, and with new and improved methods, techniques, and. equipment. Iron Range Developments Much attention has been given during the year to the tremendous program for beneficiation of taconites and intermediate iron ores which is progressing through large pilot-plant tests preparatory to full-scale production operations. The greatest activity has been directed toward concentration of magnetic taconites on the Mesabi Range. The Reserve Mining Co. has let $75 million in construction contracts for the 2 ½ million-ton-per-yr project (concentrates) at Beaver Bay, Minn., and is building a 300,000-ton-per-yr pilot plant to prove up the magnetic separation and pelletizing operations. Oliver Iron Mining Co. has a pilot plant under construction near Mountain Iron for concentrating magnetic taconites, and is operating experimentally a sintering and nodulizing plant on fine ore screenings and concentrates at Virginia to fully develop agglomeration technique. The Erie Mining Co. plant at Aurora continues its production of concentrates from magnetic taconites which was begun three years ago. No plans have been announced to treat the Mesabi Range nonmagnetic taconites, but F. D. Devaney, Pickands Mather and Co., is studying a new process for magnetically roasting lean ores to make them amenable to low-intensity magnetic concentration. W. R. Van Slyke, Cleveland-Cliffs Iron Co., calls attention to several noteworthy developments in the field of intermediate ores, perhaps the most significant of which has been the first commercial operation of a Dutch State Mines (DSM) cyclone plant at the Buckeye mine of the M. A. Hanna Co. The plant concentrates the +1/4 in. fraction by means of conventional heavy-media treatment after suitable crushing, screening, and washing. The -1/4 in. +65 mesh material is treated in two 12-in. cyclones, the -65 mesh fraction being sent to tailing storage. The plant is operating successfully on feed rates up to 120 tons per hr, and indicates that successful treatment of the fine fractions of Mesabi intermediate ores is imminent. Another commercial-size DSM plant was placed in operation late in the year by Cleveland-Cliffs at the Holman mine, and two additional ones are expected to be in operation next year. Various other methods are also in use at different plants for treatment of the fine fractions, including classification, abrasion milling followed by classification, jigging, and Humphrey spirals. Where it can be economically justified, it seems at present that heavy-media treatment of the -1/4 in. fine fraction will also come into increasing use on the intermediate ores. During 1951 a one-unit, heavy-media plant to treat hematitic crude ore was erected at the Ohio mine on the Marquette Range by Cleveland-Cliffs and plans for another plant at Humboldt to produce 2000 tons of concentrates annually is contemplated, as is also the construction of a plant for agglomera-

Jan 1, 1952

By J. J. Mulligan

Introduction Coal is found in every major geographic region through-out Alaska and in two offshore areas. Since about 1852, more than 100 small mines have opened and closed. In 1981 and 1982 production was almost entirely from one mine in central Alaska. Clearly, the utilization of Alaska's abundant coal resources presents political, economic, and technical problems that are far from solution. Location and Physical Features Figure 1 illustrates the geographical and geological similarity between Alaska and the western US. Alaska's Arctic region generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of the western US. The southcentral and southeastern regions have a similar resemblance to the Sierra Nevadas and the West Coast. The Arctic, the central, and the southcentral regions have major coal fields. The southeast region has scattered occurrences. The topographic, climatic, and economic characteristics of each are different. These differences have a large effect on practical mining methods. Description of Alaskan Coal Coal deposits known in Alaska are almost all of Cretaceous or Tertiary age, much younger than the Carboniferous coal deposits of eastern and midwestern states. Consequently, most Alaskan coals have a higher moisture content and a lower heat value. Most Alaskan coals also have a much lower sulfur content. Low volatile bituminous, and anthracite coals occur in Alaska, but most Alaskan coals range downward in rank from high volatile bituminous to subbituminous and lignite. Alaskan coals are similar to coals of the northern Great Plains and the Rocky Mountains. Arctic Region Northern Alaska Coal Fields Northern Alaska coal fields are by far the largest group of coal deposits in Alaska (Fig. 2). Coal-bearing rocks extend from the foothills of the Brooks Range about 160 km (100 miles) northward to within about 80 km (50 miles) of the Arctic coast. The principal known occurrences are between the Colville River and the western coast. However, coal has been found eastward almost to the Canning River and westward under the Arctic Ocean. The northern Alaska coal fields are in a series of Cretaceous rocks that suggest a deltaic depositional environment. The beds tend to occur in series of up to eight or nine beds totaling 6-9 m (20-30 ft) of coal. However, beds 6-12 m (20-40 ft) thick have been reported, and beds 1-3 m (3-10 ft) thick seem to be relatively common. Including thin seams, coal in some places makes up about 10% of the stratigraphic section. However, no area has been explored in sufficient detail to block out any large body of reserves or to make reliable estimates of the total resource. Observation points in drill holes and along river and stream banks are few and far between. Coals in northern Alaskan fields tend to range in rank from bituminous, where moderately folded and faulted in the foothills, to subbittuminous in the gently folded rocks under the coastal plain. Coals toward the eastern extremities of the coal fields may be of Tertiary age and lower in rank, but the same general correlation between degree of folding and increase in rank can be expected. Some higher rank coals in the foothills belt are known to have coking properties but most, and possibly all, require

Jan 1, 1984

By F. D. Weeks

The Salida smelting plant, owned by the Ohio & Colorado Smelting & Refining Co., is situated at an altitude of 7,000 ft., about 2 miles west of Salida, Colo., and 215 miles southwest of Denver. Salida is a division point on the Denver & Rio Grande R. R. where the narrow-gage line serving the San Juan region joins the through standard gage. This narrow-gage road also serves the coal and coke companies at Crested Butte and the lime quarries and mines at Monarch and Garfield, which are only 20 miles distant. These facts, together with the possibility of an appropriate site, doubtless influenced the builders to locate at this point. The smelting plant and yard occupy 80 acres of land on the northeast side of the Arkansas River. The slope of the ground is such as to permit of the ore being delivered by cars at a point 25 ft. above the feed floor; and in front of the furnaces there is a fall of 50 ft. for the slag dump. A recent purchase of river bottom has provided slag room for 20 years. As originally constructed, the plant consisted of four blast furnaces, 40 by 144 in. at tuyéres, two copper-matting furnaces, dust chamber, stack, power plant, blowers, sampling works, and one railroad trestle about 16 ft. from bed floor to rails. Later 12 hand roasters of excellent design were added and the practice of smelting leady matte in a copper-matting furnace was abandoned. Since the plant passed under the present management the equipment has been increased so that the following is a brief description of the same at this date: Two lead blast furnaces, 48 by 180 in. at tuyéres, 17 ft. 6 in. tuyéres to feed floor; four lead blast furnaces, 40 by 144 in. at tuyéres, 17 ft. 6 in. tuyéree to feed floor; two copper-matting furnaces, not used; blast-furnace flue, 900 ft.; area 245 sq. ft.; blast-furnace stack, 150 ft.; above furnace floor, 190 ft. When smelting a 500-ton charge per day, the gases approximate 63,700 cu. ft. per minute and travel at a speed of 260 ft. per minute. The slag is hauled by a 10-ton electric locomotive; the slag shells and settler refuse are elevated to a bin on the feed floor by an electric hoist. The matte is tapped in 1,600-lb. cakes and loaded into cars

Jan 1, 1916

By J. E. Miller, W. E. DeVaney, L. Stroud

During a recent phase study of a natural gas, two stable equilibrium liquid phases were observed at temperatures below —200°F and pressures above 200 psi. This paper reviews the published literature on the occurrence of multiple equilibrium liquid phases and presents analytical data for the vapor and two equilibrium liquid phases of the liquefied natural gas at five experimental conditions. In addition, data for 30 conditions of two-phase equilibria are included. INTRODUCTION The low-temperature phase behavior of gases, most of which contained helium, has been investigated in the laboratories of the Helium Activity for many years. Since 1952, experimental studies of these systems have been continuous as part of the research program at Amarillo, Tex. Because of their value to private industries interested in participating in the Helium Conservation Program, several "Open File" reports containing phase equilibria data for heliurn-bearing natural gases have already been released by the Helium Activity. A paper containing information on the general phase behavior, operating criteria and extensive vapor-liquid data for two helium-containing systems was recently published.2 Additional publications presenting experimental data on the phase relationships of various gas systems are now in process and will be available in the near future. PREVIOUS EXPERIMENTAL WORK Although the formation of multiple liquids has been reported for various systems, to our knowledge this paper is the only substantiated evidence of a vapor-liquid-liquid equilibria in a naturally occurring gas. In 1940, Vink, Ames, and others13 reported the presence of two liquid phases in a hydrocarbon system consisting of mixtures of crude oils, solvents and natural gas. Eilerts and co-workers; published data on the recombined fluids from a gas-condensate well. This condensed gas, containing approximately 76 per cent methane and 24 per cent ethane-plus, exhibited two distinct liquid phases. Weinaug and Bradley 14 observed "unusual" phase behavior in a reservoir mixture. These workers postulated that the anomalous phase behavior was due to the "imminent formation of a second liquid phase". Botkin, Reamer, Sage and Lacey 1 studied two California crude oils that exhibited multiple phases. Kohn and Kuratal0 recently reported two equilibrium liquid phases in the methane-hydrogen sulfide system. Roof and Crawfordl1 and Eakin, et a16 also have reported experiments with binary systems that formed two stable equilibrium liquid phases. APPARATUS AND PROCEDURE A U. S. Bureau of Mines Phase Equilibrium Apparatus was used in conducting this study. The apparatus and procedures employed in its operation have been previously described3 and will not be repeated in detail ill this report. Briefly, the apparatus consists of a windowed cell which can be maintained within ±0.5°F for temperatures between room temperature arid -320°F. Pressure within the cell can be maintained within 0.1 per cent of gauge reading up to 800 psig. Equilibrium vapor and liquid samples are obtained in special containers4 for analysis by a mass spectrometer. Although the accuracy of the analyzer is about ±0.1 mol per cent, the reproducibility of the phase-equilibrium apparatus is considered relatively poor. Values reported from methane and nitrogen are considered accurate to ±l.0 and ±0.6 mol per cent. Data for ethane-plus in the vapor are accurate within 0.2 mol per cent; liquid-phase data for this aggregate compolnent are accurate within 1.5 mol per cent. For helium in the vapor phase, the analytical data are accurate within 0.2 mol per cent; liquid-phase analyses for this component were obtained by the charcoal adsorption method described by Frost8 and are accurate within 0.006 mol per cent. All of these references to the accuracy of reported values are conservative estimates based upon a statistical treatment of reproducibility data obtained with the apparatus.

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

By R. L. Mauger, P. E. Damon, B. J. Giletti

This report includes the lead isotopic dating of a suite of galenas from Arizona and an application of the K-Ar method to the dating of a Laramide porphyry copper deposit, the Silver Bell Mining District. The lead isotopic data supports prior age assignments based upon geologic inference. The Silver Bell study illustrates the necessity of correlative geologic and petrographic investigations for the interpretation of the results of potassium-argon dating. LEAD ISOTOPIC DATING OF GALENAS FROM ARIZONA ORE DEPOSITS A group of galenas from Arizona ore deposits have been analyzed for lead isotope ratios. The results were used to calculate model ages by the. method of Russell, Stanton and Farquhar,l6 in which the age is calculated directly from the Pb206/Pb207 ratio. The use of Pb206/Pb207 ratios eliminates the errors inherent in measuring the abundance of Pb204. The Holmes-Houtermanns model is the other model commonly used for calculating model ages. Both models assume that any lead sample is composed of primeval and radiogenic components and the calculated age is the time at which the lead was extracted from its source area. Using the Holmes-Houtermanns model, a lead is ordinary if its isotopic ratios lie on an isochron. The growth curve that passes through the experimental point determines the U/Pb ratio in the source area. The RSF model assumes the source area for conformable leads is the mantle, that this has a uniform U/Pb ratio, and thus all ordinary leads must lie on a single growth curve, having a mantle U/Pb ratio. The definition of an ordinary lead differs between the models, and differences in age arise mainly from the assumptions made to evaluate parameters in the model equations. These assumptions depend on the hypothesis chosen to explain ore genesis. In the RSF Model, the Pb206/Pb207 ratio is derived as a function of time. The equation contains three undetermined parameters which are evaluated by assuming three known points lie on the curve. These are the following: 1) Primeval lead from the Canyon Diablo and Henbury meteorites, 2) Modern conformable leads which lie on Patterson&apos;s zero isochron, 3) Lead from the Bathurst, New Brunswick base metal deposits. The Bathurst deposits are postulated to be examples of "conformable base metal deposits", as proposed by Stanton.l9 A conformable deposit has a particular genetic history and, as a result, the orebody conforms to stratigraphic layering in the host rock. The metals are brought to the surface in volcanic rocks which originated in the mantle. Weathering products of these rocks, including sulfur and metals, accumulate in areas undergoing sedimentation. The formation of sulfide ion in the sediments by the action of sulfate reducing bacteria causes fixation of iron as pyrite. If the pyrite becomes concentrated in favorable stratigraphic horizons, any base metal deposit eventually formed by replacement of pyrite will have a strata bound character. Compaction and expulsion of pore water from the sediments at depth result in upward mobility of solutions containing soluble base metal chlorides. The strata with high pyrite content act as chemical traps for the base metal ions and replacement occurs. An important result of this general evolutionary model is that, if complete separation of lead and parent isotopes occurred during accumulation of the sediments, any ore deposit formed solely of metals derived from those sedimentary rocks will contain "conformable" lead. This would be true even if the actual ore deposit were formed at a later date by some epigenetic process. In this case, mineralization would be controlled by local conditions, and need not conform to stratigraphic layering. Also, any ore deposit containing lead derived from a mantle or mantle-like source, even though not conformable in Stanton&apos;s sense, will fall on the curve for conformable ores and thus give a meaningful model age. Model ages for Arizona galena deposits are listed in Table 1. Fig. 1 is a location map. Jerome-Humbolt District: Galenas from the United Verde mine at Jerome and the Iron King mine at Humbolt give model ages of 1750 m.y. and 1640 m.y. respectively. Both deposits are massive sulfide bodies in a host rock of older Precambrian

Jan 1, 1965

By A. D. Hill, R. S. Schechter, M. P. Walsh, I. H. Silberberg, M. J. Humenick

There are many uranium deposits which are too deep, too poor in quality or too small in extent to be economically strip mined. It now appears that this uranium can be mined using in situ leaching processes. A number of field tests have been, are being or will be conducted to demonstrate the feasibility of In site leaching. Preliminary results are encouraging, but a major question concerns the restoration of the mine site, which is generally contained within an aquifer. It is necessary to ensure that the quality of the water is not adversely affected by the mining operation. One component of the lixiviant is necessarily a cation and, during the course of mining, the ion exchange sites of the minerals in the mine zone become saturated with this cation. Ammonium is the cation now commonly used. Clearly, any restoration procedure or question involving the rate of cation migration with the groundwater all necessarily involve the process of ion exchange coupled with flow in porous media. The equations describing this process are presented in this paper and numerical solutions obtained. Preliminary results showing the effect of isotherm shape, cation exchange capacity, flow and dispersion are presented. These results demonstrate that in many situations cation migration in ground water will be slow.

Jan 1, 1979

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By E. A. Gulbransen, J. W. Hickman

Recent work by the authors1 on the oxide films formed on alloys of titanium and zirconium with nickel and copper indicated that an investigation of the oxides which form on alloys of copper and nickel might permit the relative rates of formation and diffusion of the ions of these metals to be determined. This binary system is of further interest since the alloys which form are of the solid solution type over the entire range. In addition nickel is much more oxidation resistant than copper. A comparison of the free energies of formation of the simple oxides which may occur on these alloys indicates that nickel oxide should be observed over the entire time and temperature ranges of oxidation for all alloy compositions~i In order for nickel oxide to predominate on the surface, it is necessary that nickel ions form and diffuse to the surface. Two factors which may influence the formation of nickel oxide may be the ionic sizes, where cu+ is o.,,6-,4 and ~i++ is o.,oh;, and the charges on the ions. On the basis of size, Ni++ should diffuse more readily than Cu+ while on the basis of charge, Cu+ should form more readily than Ni++. According to Uhlig2 passivity to corrosion in an alloy appears at a critical composition which for copper-nickel alloys is related to the tendency of the d band of electronic energy states to fill with elec-trans. This in in the copper- nickel alloys corresponds to 40 at. pct nickel at which composition Uhlig2 (quoting La Que&apos;s data) states that the alloy system becomes passive. Magnetic and specific heat data indicate that the d band of copper-nickel alloys is flied at 60 at. Pet Or or 4O at. pct nickel. Matt and Jones3 have shown that if, on alloying nickel with copper, one considers a copper atom to be identical with a nickel atom except for an extra electron (nickel has the configuration: 3ds 4s2 and copper: 3 dl0 4s) then at 60 at. pct copper or 40 at. pct nickel enough electrons are contributed by copper to fill the d band of the alloy. At this composition the magnetic susceptibility approximates zero according to Grew.4 Although the electron diffraction data will not determine the rates of the several reactions which may occur during oxidation, yet a determination of the structures of the surface oxides may yield information concerning the relationships, if any, which may exist between the oxide structures which form and that composition where the magnetic susceptibility approximates zero. It is quite possible, of course, that the mechanisms of the oxidation and corrosion reactions may be so widely different that no correlations between them may be possible. Survey OF Literature The metals, copper and nickel, which are face-centered cubic, form solid solution alloys which are face-centered cubic with no superstructure for all compositions. Three oxides of nickel have been investigated structurally by X ray diffraction. Of

Jan 1, 1949

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,&apos; and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,&apos; and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

Edward K. Landis, Philadelphia, Pa.: In studying Mr. Thackray&apos;s paper it seemed that a critical comparison of the results from different methods therein reported would he of interest. For this purpose Table I. was constructed by grouping all determinations made by the same method, and the probable errors were calculated. In this table all chemists titrating with permanganate (A1, E, F, G and 0 of Mr. Thackray&apos;s paper) are classed under "Emmerton;" those titrating with nitric acid (C, J, S and Y) under " Handy; " those re Probable error of result: a, ±0.0008996; b, ±0.000694; c, ±0.00107; d, ±0.00115; e, ±0.000674; f, ±0.000473; g, ±0.003675; h, ±20.0007959; i,0.000.5098; k, ±0.0008303. Probable error of single determination: a, ±0.001989; b, ±0.001547; c, ±0.00214; d, ±0.0023;e, ±0.00116;f, ±0.000818;g, ±0.0019;h, ±0.00224; i, 40.00143; k, ±0.00234. The formula for calculating the probable error is 0.6745, where N (N— 1)&apos; S is the sum of the squares of the differences from the mean and N is the number of determinations.

Jan 1, 1897

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana&apos;s gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

By William R. Patterson

ACCORDING to the phase diagram for the Mn-Ni system,&apos; the high-temperature, fcc y-manganese solid solution is stabilized to below room temperature, in the range approximately 22 to 28 wt pct Ni. However, pearson2 cites evidence in the literature showing that for manganese contents greater than about 75 wt pct the quenched phase in Mn-Ni alloys is fct. This is in keeping with zener&apos;s3 suggestion that in manganese-rich alloys the fcc high-temperature phase undergoes a diffusionless or martensitic transformation to a fct structure upon quenching. Work by Basinski and christian4 on manganese-rich compositions in the similar alloy system Mn-Cu established that in alloys of greater than about 82 wt pct Mn the y-manganese phase underwent a fee fct martensitic transformation upon quenching to room temperature. Striking evidence for this martensitic transformation was the highly twinned or banded microstructure, an example of which is shown in Fig. 1. Similar microstructures have also been found in quenched Mn-Cr5 and Mn-Au6 alloys. In the present investigation, we attempted to obtain similar evidence of a fcc — fct martensitic transformation in manganese-rich Mn-Ni alloys. Manganese alloys in the range 10 to 30 wt pct Ni were prepared by arc-melting, under argon, at atmospheric pressure. The alloys all were 50 g in size, and negligible weight loss occurred during melting. The starting materials were electrolytic manganese and nickel, both of 99.9+ pct purity. The alloys were subsequently homogenized 48 hr at 1750°F, hot-rolled 50 pct at 1700°F, annealed 2 hr at 1700°F, and water-quenched to room temperature. All heat treatment was done in purified argon. Both X-ray and metallographic techniques were used to examine the structures of the quenched alloys. X-ray diffractometer studies were conducted on powder specimens obtained from filings rean-nealed 2 hr at 1700°F in argon and water-quenched. Identification of the intensity peaks from the diffractometer counter traces showed that below about 10 to 12 pct Ni the y phase decomposed partially upon quenching to give an a- + ?-manganese structure. In the range approximately 12 to 25 pct Ni, the structure was found to be fct ? manganese with a c/a ratio approaching 1.0 at 25 pct Ni. Beyond approximately 25 pct Ni, the structure remained fcc. These results, including lattice-parameter determinations, are given in Table I. Metallographic examination. was carried out on specimens polished and etched after quenching, and also on polished specimens reannealed and quenched. In the first case, the distinctive twinning or banding so prevalent in Mn-Cu alloys was sought, while in the second, the surface relief effect generally regarded as being truly characteristic of a martensitic transformation was sought. The microstructure of representative alloys in the range 12 to 25 pct Ni is shown in Fig. 2. The structure of the Mn-15 pct Ni

Jan 1, 1965

By Douglas A. Blankenship, Randall G. Stickney

The corejacking test is a field test designed to measure the response of salt to known boundary conditions. A 1.0-m-diameter salt core is externally pressurized using curved flatjacks placed in the annulus surrounding the core. Time-dependent deformation of the salt is measured by monitoring the diametrical closure of an inner borehole. A finite element elastic analysis of the jack loading system has been performed. The purpose of this analysis was to determine if the original assumption of axisymmetric loading is correct. Six loading cases were investigated, each representing either hypothetical or previously encountered jack configurations.

Jan 1, 1982

By Fred Chappell

Pyrophyllite, a hydrous aluminum silicate, physically similar to talc, receives its name from the Greek word Pyr, for fire and phyllite, a rock or stone. Firestone refers to its first recorded use as firestones or hearthstones. Composition and Properties Pyrophyllite is an aluminum silicate A12O34SiO2H2O (alumina 28.3 pct, silica 66.7 [ ] pct, water 5.0 pct) (Table 1). Vanderbilt1 gives pH value of pyrophyllite as 5.6 to 8.4. Pyrophyllite is usually white or cream, though it may be found in shades of pale green, pale yellow, buff or light gray, and in darker shades and other colors principally due to oxidation of contained iron minerals. It is opaque to translucent in thin sections. Its hardness is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. Its luster is pearly to dull; it is recognized chiefly by its micaceous structure and cleavage, and its soft greasy feel. Two other varieties occur, one in which there are radiated needles in the crystalline form, and there is also a massive homogeneous structure found. Fine grinding reduces pyrophyllite to fiat plates or scales but aggregates of minute foliated plates may be formed.1 Distribution of Deposits Pyrophyllite is found in metamorphic rocks throughout the world but it is only in comparatively recent years that it has assumed much commercial importance. The principal

Jan 1, 1960

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30&apos; to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,&apos; in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.&apos; The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956