Search Documents

By J. A. Bownocker

THE EXISTENCE of petroleum in the rocks of Ohio and Indiana seems to have been first shown by wells dug for salt. The fuel, however, was objectionable owing to its odor and inflammability. Not until the brake well was drilled in 1859 did the people appreciate the value of rock oil, and then they at once began plans to secure the coveted fuel.. The first successful well in these two states was near . Macksburg, in southeast .Ohio, where at a depth of 59 ft. (17 m.) :oil was found in commercial quantity (1860). A year later this fuel was secured on Cow Run, in the same county, and at about the same time in Noble, Morgan and perhaps other counties in that part of Ohio. The second great step in the production of oil in Ohio and Indiana was taken in 1884 when the reservoir of natural gas in the Trenton limestone of northwest Ohio was tapped, and where a year later oil was secured in the same formation. Petroleum in this limestone was obtained in Indiana in 1889.1 The third step in the production of oil' in Ohio and Indiana is associated with the Clinton sand of Ohio. Natural gas in large volume was discovered in that rock at Lancaster, in 1887, and the area has been extended until it has become the largest individual producer in the world. The presence of natural gas in such great volume all but demonstrated to the driller that-oil lay hidden near by. Soon the search for it was started but not until 1899 was petroleum in commercial quantity found in the Clinton sand, and a large pool was not located in it until 1907. The fourth step in the development of the industry was taken in 1913, when the pool in Sullivan County, in western Indiana, was opened. The producing rock is the Huron sandstone, which is the topmost member of the Mississippian system.2

Jan 2, 1920

By Rees D. Rawlings, C. W. A. Newey

The aging characteristics of an Fe-11 at. pct Mo alloy have been studied by means of light metallography together with density, Young&apos;s modulus, and hardness measurements. The results were consistent with the precipitation of a single intermetallic compound during aging; overaging was slow relative to that in other iron-based binary alloys. The solution treatment temperature had a small effect on the rate of hardening whereas deformation prior to aging had a marked effect on both the rate of hardening and the peak hardness. The density data indicate that the compound precipitated is Fe3MO2 and not the Laves phase Fe2Mo. Analysis of the modulus and density results gave values for the time exponent for precipitate growth of approximately 1.0 and 1.5 for the alloy aged with and without prior deformation, respectively. DETAILED studies of precipitation hardening in bcc matrices have been confined largely to the effects of carbides and nitrides. In view of this and the growing technological interest in intermetallic compound strengthening, e.g., in maraging steels, a study of precipitation in iron-based alloys with a low interstitial content has been undertaken. This paper is concerned with the aging behavior of an Fe-11 at. pct Mo alloy; the mechanical behavior of the alloy will be reported later. The early work of sykes on Fe-Mo alloys showed that precipitation of the intermetallic compound was accompanied by an increase in hardness and a decrease in volume of the material. More recent surveys of the strengthening associated with precipitation have been made3-5 and, in particular, Elsen and wassermann4 showed that deformation prior to aging increased the rate of hardening. These latter workers also followed the precipitation process by means of dilatometry, electrical resistivity, and lattice parameter measurements. Their results confirmed that there is a decrease in volume on aging. Except for the work of Hornbogen on an Fe-20 at. pct Mo alloy, neither clustering nor the precipitation of a nonequilibrium phase has been observed in Fe-Mo alloys. Studies of alloys of lower molybdenum content475 indicate that the equilibrium intermetallic compound is precipitated during aging. However, there is some doubt concerning the nature of the equilibrium precipitate phase. According to the phase diagram constructed by Hansen,8 the phase should be precipitated. This phase has a rhombohedra1 crystal structure which is characterized by the formula Fe706,&apos; although the composition of the molybdenum-rich boundary corresponds approximately to Fe3Mo2. The version of the diagram proposed by Sinha, Buckley, and Hume-Rother indicates that the A phase, a Laves phase Fe2Mo, should be precipitated. Their observation of a Laves phase supports the earlier findings of Bechtoldt and Vacher,13 although, in a recent study of the system by means of diffusion couples, Rawlings and Newey did not detect the phase. The work presented here describes the effect of solution-treatment temperature, aging temperature, and prior deformation on the aging characteristics of the alloy as revealed by light metallography together with hardness, density, and Young&apos;s modulus measurements. In addition the density data are used in an attempt to determine the compound precipitated during aging. EXPERIMENTAL PROCEDURE A 29-kg ingot of the alloy was cast at R.A.R.D.E., Fort Halstead, from deoxidized, Japanese electrolytic iron and sintered molybdenum. The ingot was homogenized for 6 hr at 1473°K and then worked, with intermediate anneals, into 6- and 16-mm-diam rods and 6-mm plate. Chemical analysis of the alloy gave, wt pct: Mo, 17.5 (11 at. pct); C, 0.003; Si, 0.002; S, 0.005; P, <0.002; and02, 0.0098. Solution treatments were carried out under a dynamic argon atmosphere in a vertical, "crusilite" element, furnace which had a facility for rapid quenching into iced water. Except for the study of the effect of solution treatment temperature, all specimens were solution-treated at 1573" * 2°K for 1 hr. Salt baths were used for the aging treatments. Specimens for hardness, density, and Young&apos;s modulus measurements were produced, after heat treatment, from the stock rod or bar using a precision silicon carbide slitting wheel. As described later, the quenching treatment produced local plastic strain in the stock material; consequently, care was taken to ensure that the specimens were not prepared from these regions. Those specimens used in the studies of the effects of prior deformation on the aging behavior were strained in compression in a Denison universal testing machine. Specimens for light metallographic observations were mechanically polished on successively finer grades of diamond paste down to and then etched in either alcoholic ferric chloride or in a 2 pct nital solution. Vickers diamond pyramid hardness data were obtained using a 30-kg load. At least five impressions were averaged for each determination. Density measurements were made using a displacement technique in which each specimen was weighed in air and in dibromoethane at 296°K. The specimens were cylindrical and weighed 3 to 4 g; all weighings were made on a balance reading to 1 x 10"5 g. For each specimen the mean value of five weighings was used to calculate the density. The density of the dibromoethane was determined using the displacement procedure and a standard nickel specimen. The error in an absolute density value was estimated to be HI.01 pct. To obtain the density as a function of aging time a single specimen was used and the density meas-

Jan 1, 1969

By A. A. Smith, J. S. Smart, A. J. Phillips

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By A. J. Phillips, A. A. Smith, J. S. Smart

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By C. R. Fettke

In 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northwest of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and LUX. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J. Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey. Stratigraphic Position of the Producing Sand The producing sand at Hamilton Corners is encountered at depths of from 364 to 560 ft., depending on the location of the well and the topog-

Jan 1, 1928

By I. E. Rosenzweig

THE problem considered in this paper is as follows: An arbitrary horizontally stratified area is given. The electrical properties of this area are characterized by a function p(z) (Fig. 1), which shows the relationship between resistivity p of thes oil and the depth z. For such general case the apparent resistivity p* will be computed, by FIG. 1.-GRAPH OF FUNCTION p(z) FIG. 2.-GRAPH OF p(Z) FOR n HOMO-GENEOUS LAYERS. earth-resistivity measurements carried out by any given configuration of electrodes. General solutions of this problem appear to be very important for interpretation of field results of resistivity measurements, concerning structural investigations. Such solutions have been given by many authors for the special case of a finite number of homogeneous layers (Fig. 2)1-4 as well as for the more general case of continuously rang-ing resistivities. 5-8

Jan 1, 1939

By D. W. Fuerstenau

MEASUREMENT of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions.1,2 Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus." The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes. The assembled apparatus is shown schematically in Fig. 2. To eliminate CO2 from the solutions, all experiments are conducted in a nitrogen atmosphere. Nitrogen, used to drive solutions through the plug, is passed through a bottle of concentrated KOH solution to remove CO2 (9). A 9-liter ballast reservoir (10) is used to maintain a more nearly uniform pressure. A series of stopcocks controls the direction of flow nitrogen to the flasks (11). Tubes of as-carite prevent backflow of CO2 into the system (12). Driving pressure, which can be set at any desired value, is measured with either a water manometer (13) or a mercury manometer (14). Reservoir flasks have side arms for making pressure corrections for the difference in water levels in the flasks. Streaming potentials are measured by the circuit illustrated in Fig. 2. The electrodes from the plug are connected through mercury wells (15) to a reversing switch (16), which reverses the polarity of the electrodes depending on the direction of flow of solution through the plug. The streaming potential is measured with a Leeds and Northrup type K2 potentiometer (17). Proper choice of null instrument is important because Eq. 1 assumes that the current which escapes through the measuring instruments is negligible. An ordinary galvanometer cannot be used to determine the null point because

Jan 1, 1957

Mark R. Lamb, Torres, Sonora, Mexico (communication to the Secretary*): I have read Mr. Merrill&apos;s paper with much interest, and cannot but accept his challenge as regards the cost of the clean-up at the Homestake mill. If I understand him correctly, the two men take the precipitates from the presses in about six hours, and do nothing towards refining them. If that is so, it would correspond to the work four men do here in about eight hours—that is, to clean the box and to place the precipitates in the driers. In order to make a fair comparison, the bullion in each case should be stated in ounces, since it is as diflicult to precipitate silver as gold, and our bullion is mostly silver. Bullion to the value of $50,000 is equivalent to a weight of about 2,500 oz. At our last clean-up eight standard bars, each 1,100 oz. in weight, were made, which equals a total weight of 8,800 oz&apos;. Four men had the precipitates drying by 8 p.m. This plant, the Minas Prietas works of Charles Butters & Co., at Minas Prietas, has square-bottomed electrolytic vats, an arrangement which necessitates the handling of all the precipitates in buckets. The Butters plant at Virginia City, Nev., is equipped with conical vats, and probably could make a still better showing under similar conditions. Another point is that common labor only is required. (Ordinary laborer&apos;s wages at Minas Prietas are $0.70 gold.) I may say also that, except for the convenience of the refinery, the box could be cleaned monthly, instead of bi-monthly, at only a slight additional expense. The comparison, if made a few months ago, would have been much more in favor of the electrolytic process, as the tailings handled at that time contained a large quantity of copper, and the amount of zinc-dust required would have been enormous.

Jan 1, 1904

By H. A. Doerner

PROPOSALS to use hydrocarbon or natural gases for the reduction of zinc from oxide materials may be traced back through Patent Office files to the early years of the present century. Natural gas at rates cheap enough to compete with solid fuels has been available at or near one major zinc district for more than a decade. That the seemingly meritorious and economically interesting applications of these proposals have not devel-oped into workable processes for direct production of zinc by natural gas cannot be completely ascribed to the proverbial conservatism of the zinc industry. It is possible to produce spelter commercially in normal times from zinc oxide and carbonaceous reducing agents without having a very precise understanding of the chemistry of the process. The reduc-tion by hydrocarbons is not, however, in this class, and the technical complexity of this reduction metallurgy and chemistry prohibits solution of the inherent difficulties by the "hit and miss" methods that are some-times thought to be practical. In a thermodynamic study of the chemistry of zinc smelting, Maier1 made a preliminary study of the chemistry of the use of methane for reducing zinc oxide by thermodynamic means, pointing out that the following reactions, the limits of which could be theoretically predicted, were important: ZnO + CH4 = Zn(gas) + CO + 2H2 [1] CH4 = C -I- 2H2 [2] ZnO + CO = Zn(gas) + CO2 [3] ZnO + H2 = Zn(gas) + H2O [4] Other possible reactions, not discussed in the reference quoted, are: CO2 + CH4 = 2CO + 2H2 [5] H2O + CH4 = CO + 3H2 [6]

Jan 1, 1933

By Joseph W. Richards

The Ashio copper-mine of the Furukawa Mining Co. is situated 18 miles from Nikko, and 109 miles north of Tokyo, near the center of Japan. The mine-waters are run over scrap-iron, whereby most of the copper is precipitated as cement-copper, leaving iron sulphate with some copper sulphate in solution. After using in the wet concentrating ore-dressing plant, the waste water contains clay and ore-slimes. The only avenue of disposal of this water is the Watarese river; but as this flows through valleys in which the water is used for irrigating the rice-crops, it is necessary to purify and clarify the water before discharge. The water amounts to from 600 to 700 cu. ft. (from 17 to 20 cu. m.) per minute, and averages about 0.00028 per cent. of copper, representing more than 18 tolls of copper per month. The water carries H2SO4, FeSO4, Fe2(SO4)3, CuSO, and other metallic sulphates in solution, and clay, ore-fines, slimes and basic iron sulphates as suspended matters. To purify and clarify the water, precipitation by milk of lime has been used, in three different ways, as follows: I. First Method, Copper not Recovered. Milk of lime was run into the water, and the mixture run through six settling-ponds, and then through a sand filter into

Jan 1, 1913

The following officers and committee chairmen were elected: Honorary Chairman, Herbert Hoover; Chairman, Elmer A. Sperry, New York; Vice-Chairman and Chair-man of the Executive Committee, John W. Lieb, New York; Vice-Chairman, C. E. Grunsky (Pacific Coast), San Francisco; C. F. Kettering (Middle West), Detroit; Execu-tive Secretary, Maurice Holland; Executive Committee: Gano Dunn, George W. Fuller, Maurice Holland, Frank B. Jewett, John W. Lieb, H. J. McGraw, Calvin W. Rice, W. E. Wickenden, all of New York; Dugald C. Jackson, Cambridge, Mass.; 0. C. Merrill, Washington, D. C.; Charles F. Scott, New Haven, Conn.; Elmer A. Sperry, Brooklyn, N. Y.; Finance Committee. John W. Lieb; Technical Program Committee: D. C. Jackson; Transporta-tion Committee: F. B. Jewett; Entertainment Committee: 0. C. Merrill; Publicity: J. H. McGraw; Promotion and Attendance: George W. Fuller.

Jan 5, 1928

By Thomas E. Garnar

Zirconium and hafnium are curious elements because they are almost always found together in nature. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium&apos;s chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and Von-Heresey detected it using x-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO4) and less commonly as the oxide baddeleyite (ZrO2). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. Zircon is always a coproduct from TiO2 mining and processing. During World War I it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s when Zircon Rutile, Ltd. began mining at Byron Bay on the east coast of Australia that zircon was first used as a foundry sand. Later in the 1940s, NL Industries, Humphreys Gold Corp., and E. I. du Pont de Nemours & Co., Inc. began production of zircon sands from fossil beaches in northeast and northcentral Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties as well as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by South Africa and the US. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, China, Thailand, and Brazil. Undeveloped heavy mineral beach sand reserves containing zircon are known to occur in Egypt, Malawi, Senegal, and Tanzania. Locations are shown in Fig. 1. Mineralogy Zirconium and hafnium are always present together in naturally occurring compounds. Most commonly they form as the silicate sometimes containing iron, calcium, sodium, manganese, and other elements. Less commonly they are found as oxides in combination with titanium, thorium, calcium, and iron. Zircon is the most common form. It is extremely resistant to weathering, therefore, often it is present in ancient beach sands and placer deposits. Although resistant to alteration from external sources, it is vulnerable to internal alteration as the result of thorium and uranium substituting for zirconium either in the zircon lattice or in solid solution. Alteration to the metamict state takes place as radioactive emanations from these elements disorder the crystal lattice, accompanied by hydration, reduction in specific gravity, and changes in color. The mineralogy of zircon and baddeleyite and variation of physical and chemical properties are shown in Table 1. The effects of zircon&apos;s internal alteration and darkened color can be corrected by heating to 1000°C for 30 min or so. A certain time-temperature relationship makes it possible for decolorization and reordering of the crystal lattice to take place when heating at higher temperatures for shorter periods or at lower temperatures for longer periods. After heating, x-ray diffraction patterns are sharper, the grains may be harder, and except for particles of malacon, the grains will be white or colorless in the absence of grain surface coatings. The color change is only temporary and the particles slowly darken with time. Zircon fluoresces light yellow in shortwave ultraviolet light. If exposed to ultraviolet light for extended periods of time, white (calcined) zircon turns purple. With time the induced color begins to fade and eventually disappears (e.g., calcined Florida zircon exposed to ultraviolet light for 24 hr still retains faint, but discernible, purple color after six months).

Jan 1, 1983

By L. W. Saperstein, D. Yeung, L. B. Phelps

Introduction The success of preventive methods for the mitigation of coal mine drainage formation will require a marriage of the minimization of initial coal mine drainage formation, the minimization of toxic fluid formation after toxic material disposal, the minimization of the mobilization and transpor¬tation of formed toxic fluids, and the maximization of the rate of diultion and attenuation of the formed toxic fluids. This paper contributes to the understanding of factors af¬fecting mobilization and dilution and attenuation of formed toxic fluids. When water containing a salt content different from in situ pore water in the soil is passed through a body of soil, the concentration of salts in the outflow will gradually change composition in a manner that depends on the kinds of hydraulic processes that occur in the soil. These processes are molecular diffusion, lateral dispersion, longitudinal dispersion, chemical reactions or exchange, physical adsorp¬tion, and biological retardation. This note considers only the first three processes. These three microscopic processes can be analyzed statistically on a probability basis. Such results, confirmed experimentally, indicate that a tracer introduced instantaneously as a point source will tend to form a Gaussian normal distribution as it moves downstream (Todd, 1964). Dilution During Flow The closed-form soltuion for pulse or instantaneous injec¬tion of a tracer during confined flow in a homogeneous porous medium shows that the maximum tracer concen¬tration at a point in space, x, after the time interval, t*, is given by [ ] where Aa is the effective flow cross-sectional area; A is the column cross-sectional area; a is soil porosity; M is mass of the injected tracer; C is concentration of the tracer in the permeating fluid and is a function of x and t*; D is the longitudinal dispersion coefficient; and va is the interstitial fluid velocity (Klotz and Moser, 1974). Therefore, the following conclusion can be made: • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, and a fixed mass of injected tracer, M, Cmax will decrease as the time of peak outflow concen¬tration t* increases. • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, a fixed mass of injected tracer, M, and a constant interstitial fluid velocity, va Cmax will decrease as the distance of travel, x, increases. • For a medium of constant cross sectional area, A, con¬stant soil porosity, a, a constant mass of injected tracer, M, and a fixed distance of travel, x, Cmax will decrease as D/va increases. Klotz and Moser (1974) concluded that D is about proportional to no.3 where r) is the kinematic viscosity; D is about proportional to a-3 where a is soil porosity; D in¬creases with increasing grain size; D increases as grains become less spherical; D increases with greater grain rough¬ness and angularity; D increases with increasing uniformity coefficient; and D is significantly affected by grain size and uniformity coefficient. The remaining parameters are not significant. Numerical Simulation Studies Numerical simulation studies were used to investigate the nature of flow and the optimum length of a toxic package within a saturated porous medium of fixed dimensions and configuration (Fig. 1). The width and position of the package was maintained constant (Phelps et al., 1981). Results indicate that if the package extends throughout the length of the model, the flow is vertically downward and

Jan 1, 1984

By Gerard Matthes

WITHIN the last three years, aerial mapping has made wonderful progress. Its three sources of development in North America may be enumerated as follows: (1) The work of the U. S. Army Air. Service and Corps of Engineers at the McCook Experimental Field, Dayton, Ohio. This is generally regarded as the backbone of this class of endeavor in the United States. (2) In Canada, a great deal has been accomplished in a practical way by methods that have not even been tried out in the United States. Under the leadership of the late Doctor Deville, the Dominion Land Surveyors have turned out reconnaissance maps of large areas at very, small cost. (3) Private capital has contributed a great deal toward development of aerial mapping in a practical way in the United States. Prominent in this regard stands the Fairchild Aerial Surveys, Inc. which has spent large sums in research and development work, especially in the construction of aerial cameras. Its camera is, at present, the official camera of the U. S. Army and Navy Air Services, also, of the Canadian and Brazilian governments. Aerial photographic surveying is a flexible process and adapted to a variety of uses. To date, it has proved. of direct practical value for engineering projects such as reservoir and power transmission surveys, railroad location, drainage, harbor front studies; also, for many commercial purposes, tax assessment, city planning, forest surveys, and lawsuits. In a few instances, aerial photographs have been used successfully by geologists as base maps on which to record field observations, thereby dispensing with pacing and compass surveys. There is reason to believe that, eventually, the aerial map will find wide application in the work of geologists. The reason for advancing this opinion is that aerial maps have, in other fields, proved more complete as regards detail than maps made by standard processes of surveying and drafting, and often are more accurate than the latter. At the present time, five distinct uses are being made of aerial photographs: There is the "oblique" photograph taken at an angle with the horizon; it is used extensively for illustrations in newspapers, magazines, and advertisements. Also, for reconnaissance purposes, it has been found of great practical value. For illustrating reports of engineers and geologists, it offers many obvious advantages. In the Canadian Surveys, maps have been compiled from oblique photographs.

Jan 3, 1925

By M. E. Wadsworth, I. B. Cutler

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the ( potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum ( potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the i potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as pH, reagent concentration, and floc size and density.2 Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By R. F. Sheldon

The discovery of the Carlin deposit was the result of discriminating geologic research and prospecting devoted to the objective of finding a gold deposit that could be mined by open pit methods. By the late 1950s, Newmont Mining Corp. was becoming increasingly concerned about the trend of rapidly rising underground mining costs unless bulk mining methods could be applied. The desirability of finding an open-pittable gold deposit was apparent. The attention of Newmont geologists was directed to Nevada by the publication of two papers: "Paleozoic rocks in North-central Nevada" (1958) and "Alinements of Mining Districts in North-central Nevada" (1960), both authored or co-authored by Ralph J. Roberts of the United States Geological Survey. John Livermore, geologist of Newmont Exploration Ltd., attended a talk given by Roberts in Ely, Nevada in the summer of 1961. These papers and the address by Roberts gave details concerning the Roberts Mountain overthrust, a 483 km (300-mile) long, shallowdipping fault which pushed clastic and volcanic rocks of early and middle Paleozoic age eastward over younger marine formations. Subsequent uplift and doming with consequent erosion had locally removed the upper plate strata exposing windows of lower plate carbonate rocks. Roberts noted that the principal mineral deposits of the region, including gold, were associated with these windows which exhibited a preferred alinement. In the summer and fall of 1961 Newmont&apos;s exploration geologists John Livermore and J. Alan Coope began a systematic examination of gold occurrences associated with these windows, aided by further discussion with geologists of the US Geological Survey. Attention was directed to the Lynn and Carlin windows, particularly to those formations lying immediately above and below the Roberts Mountain fault. It was appreciated at the time that many of the gold occurrences in the region were unusual in that no colours were obtained even when panning high grade samples. A large number of rock samples were collected and analysed using fire assaying procedures, and background values for gold were established. This systematic rock sampling resulted in the identification of a distinct area of anomalous gold values, and a block of claims was staked in late October, 1961. These claims, plus an adjoining optioned 32.4 ha (80 acres) of ground, cover the main area of the present Carlin gold mine. Prior to snowfall that winter, one of the bulldozed assessment pits required to establish a claim&apos;s discovery exposed 24 m (80 ft) of mineralization assaying 0.007 kg/t (0.22 oz per st) gold. In the spring of 1962 a program of trenching, sampling, and geological mapping followed by rotary drilling was underway. Other properties in the area were acquired. The generally undistinguished nature of the dolomitic siltstones and silty dolomitic limestones hosting the micron-sized gold particles, coupled with the lack of visually associated guide minerals, made identification of the gold bearing areas very difficult. The entire drill column had to be assayed to ensure that values were not overlooked, as very often sections that might be assumed to be waste turned out to be high grade. On September 10, 1962 a high grade intersection of 24 m (80 ft) assaying over 0.03 kg/t (1 oz per st) gold was encountered in the third hole drilled. An expanded program of both rotary and diamond drilling led to the further delineation of the ore body. By December 1963, the exploration program had established an initial reserve of 10 Mt (11 million st) grading 0.01 kg/t (0.32 oz per st) gold. A 1.8 kt/d (2,000 stpd) processing plant was constructed and the first gold bullion was poured in May, 1965, just two years and eight months after the discovery hole was drilled. REFERENCES Roberts, R.J., Holz, P.E., Gilluly, J., and Ferguson, H.G., 1958, "Paleozoic Rocks in North-central Nevada," Bulletin American Association of Petroleum Geologists, Vol. 42, No. 12. Roberts, R.J., 1960, "Alinements of Mining Districts in North-central Nevada," Professional Paper 400-B, US Geological Survey, Article 9.

Jan 1, 1985

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By Ionel I. Gardescu

In connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,&apos; an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the displacement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S6, R4, the sand reservoir R, R1, R², F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415Ib. per sq. in. with no free gas present. This was ascertained by closing off all the outlet valves and determining the coefficient of compressibility of the system by means of the displacement chamber D. Much difficulty was encountered in eliminating all of the free gas masses from the oil reservoir. The dead oil originally present in the

Jan 1, 1932