Search Documents

By G. P. Connell, R. E. Gilmore, J. H. H. Nicolls

The purpose of this paper is to suggest a procedure for indicating the dividing line between noncaking coals and those that have weakly caking properties. A laboratory agglomerating test as an aid in classifying weakly caking coals is outlined and its merits in comparison with the standard agglutinating method advanced by the U. S. Bureau of Mines are discussed. No attempt, however, is made to discuss in detail either the different methods for determining "caking" and "agglutinating" indices or the various systems of classification. Two methods, differing somewhat in procedure, have been employed and recognized as suitable for determining the caking or agglutinating values of coals; namely, those in which an inert material such as sand, electrode carbon, etc., has been mixed with the coal before being heated, and those in which the coal is carbonized alone. In all such methods, the coal with or without the inert material is in the finely divided state and the index or value sought is derived from the examination of the residue after heating in a closed crucible or other container. The procedure outlined by Selvig, Beattie and Clellandl is the most recent representative of the method using sand as inert material, while the agglomerating test described below is representative of the method in which the coal is carbonized alone. The standard volatile-matter determination affords a means for observing the coking properties of a coal, and this has been described by Rose2 as the simplest of all coking tests. According to him, "the resulting coke button will indicate whether the coal is noncoking, feebly coking or strongly coking," despite the fact that "almost every condition in this test is at variance with large-scale carbonizing practice." Lessing,3 the

Jan 1, 1934

By Jan M. Mutmansky, Gordon H. Walrod, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to l000ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1980

By Don L. Kendall, Martin G. Buehler

A simple physical model has been developed to fit carrier-removal data in silicon irradiated near room temperature with reactor spectrum neutrons. Commonly observed donor and acceptor defect energy levels are assumed to be introduced linearly with neutron fluence. The donor levels (in ev) are Ev + 0.16, Ev + 0.27, and Ev + 0.31 and the acceptor levels are Ec - 0.55, Ec - 0.40, and Ec - 0.1 7, where Ev and Ec are the valence and conduction band energies, respectively. The introduction rates of each level are adjusted to fit literature initial carrier-removal rate data. When normalized with respect to the Ev +0.27 level, the relative values of introduction rates are 5.3, 1.0, 3.1, 1.0, 2.0, and 20.0, respectively for the six levels indicated above. To fit p-f (hole concentration vs neutron fluence) and n-f (electron concentration us neutron fluence) data, the introduction rates are multiplied by a factor which preserves the relative values given above. This factor depends upon irradiation temperature, reactor energy spectrum, neutron fluence calibration, and oxygen content of silicon. An extensive study of the effect of neutrons on carrier-removal in silicon irradiated with reactor spectrum neutrons (E > 10 kev) has been given by Stein and Gereth1 (SG) and Curtis, Bass, and Germano' (CBG). They measured initial carrier-removal rates for both p- and n-type silicon over an impurity range typical of silicon devices. In this work, we attempt to fit a simple theory to this data to establish a usable relationship between hole and electron concentration, p and n, respectively, and neutron fluence f. The p-f and n-f relations are needed to assist in the design of neutron tolerant silicon devices and are needed to clarify presently used empirical resistivity-fluence relationships.3 Neutron damage in silicon produces a variety of defects ranging from simple point defects to defect clusters. For the purpose of this treatment, we assume that simple point defects dominate carrier-removal effects. In contrast to this view, stein4 has proposed that defect clusters are responsible for a significant portion of carrier-removal effects. In the following section, it is shown that the carrier-removal effect in n-type silicon with an electron concentration less than 1015 cm-3 can be explained adequately by assuming that the divacancy is the dominant defect and that its introduction rate is independent of the electron concentration. For electron concentrations greater than 1015 cm-= an additional acceptor defect center is needed, and for simplicity the A-center (vacancy-oxygen pair) has been chosen. Although the E-center (vacancy-phosphorus pair) can account for some of the results, the A-center was chosen because the E-center requires a more involved treatment which the presently available data do not justify. In p-type silicon three radiation-induced donor levels are assumed, namely the divacancy and two other centers of unspecified nature located at Ev + 0.16 ev and Ev to 0.31 ev. The donor divacancy at Ev + 0.27 ev is assumed to be introduced at the same rate in p-type as in n-type. However, this rate is too low to fit p-type initial carrier-removal data. The dominant centers in p-type silicon are assumed to be the Ev + 0.16 ev and Ev + 0.31 ev levels where the latter is not the divacancy. The introduction rates are chosen to fit initial carrier-removal rate data. Assuming that the introduction rates are independent of Fermi level, the ratio between them is fixed for subsequent p-f and n-f calculations. Using the same ratios, the initial carrier-removal rate data1,2 as well as p-f and n-f data1,5 can be fit provided the absolute value of the introduction rates are adjusted to account for irradiation temperature, reactor energy spectrum, neutron fluence calculation, and the oxygen content of silicon. THEORETICAL ANALYSIS This analysis is basically the same as that used by Hi116 to analyze electron damage in silicon except we express the degree to which an impurity level is ionized not in terms of the Fermi level, but in terms of carrier concentration. Landis and pearson7 have used the latter approach to analyze y-damage in silicon. Neutron-induced defects responsible for carrier-removal at room temperature are assumed to be simple point defects with no interaction between defects so that they may be represented by discrete energy levels. It is also assumed that no constituent of a defect complex is used up and defects stabilize shortly after irradiation. Defects are assumed to be introduced linearly with fluence according to the product Rtf where Rt is the defect introduction rate and f the neutron fluence. Taking into account the ionization of defects according to Fermi statistics, and considering charge neutrality where minority carriers are neglected, the n-f relation is where no is the preirradiation electron concentration. The parameter Nt is the electron concentration at which the ionized defect concentration is one-half the total defect concentration (Rtf) or where Et is the defect energy level. For silicon at 300°K, ni = 1.45 X 1010 cm-3 and Ei = Ev+ 0.542 ev which was determined using Ec — Ev = 1.11 ev and me* = 1.07 mo and mh* = 0.558m0. The spin degeneracy factor, which usually appears as a number multiplying the Nt/n term of Eq. [1], is taken as unity. In effect, this factor has been incorporated into the defect en-

Jan 1, 1970

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 1400°F. (760°C.), the metal becomes non-magnetic, and at the "As point," 1670°F. (910°C.), it undergoes a change in crystalline form to become gamma iron. In the range 1400 to 1670°F., it is sometimes called beta (0) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 2550°F. (1400°C.), it changes into delta (d) iron, which is identical with beta or non-magnetic alpha iron. Pure iron melts (in a hydrogen atmosphere) at 2795°F. (1535°C.); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures. (1) For example, in heating through the As point a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 27 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always the case. For example, the specific heat reaches a sharp maximum at the A2 point although no transformation occurs. Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals which are liquid at the melting point of iron only lead, silver, and bismuth refuse to dissolve to an appreciable extent. The non-metals presumably dissolve by virtue of the formation of an iron compound; for example, sulphur is thought to dissolve as the compound FeS. However, there is no satisfactory method of proving that this

Jan 1, 1944

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By N. Brown

IT has been observed that a hexagonal-close-packed crystal will undergo the same macroscopic displacements as an isotropic material if the basal plane is perpendicular to the axis of twist.&apos; Other orientations may produce both bending and twisting, but this analysis will be confined to pure torsion of a right circular cylinder. The z axis, the axis of twist, and the specimen axis are coincident. The displacements are given by Uq = rz, Ur = Uz = 0 [1] where 4 is the angle of twist per unit length. This requires rotational slip, as discussed by Frank&apos; and Wilman, which may be observed readily. The relative rotation of adjoining slip planes is simply produced by a movement of a planar grid of screw dislocations."." The screw dislocations are of the same sign and they move radially inward. For hexagonal-close-packed metals, the grid is hexagonal and the screw dislocations lie in the < 2110 > directions. The displacement of a point is the resultant of two displacements produced by intersecting screws sweeping over the point. The dislocations must pass over the point (r, o) in such a manner that its resultant displacement corresponds to the observed macroscopic displacement. If 6&apos; is measured from the [1010] direction, then for 0 < ? < ~/3, only the [1210] and 121101 type screw dislocations are needed to produce the required displacement. If n1 screws of type [1210] and n2 of type [2110] pass over a point, then, in order that Ur = 0 n, sin ? - n2 sin (/3 — 6&apos;) = 0. [2] If the tangential displacement is to be independent of 0, then n1 cos ? + n2cos (/3 —?) = N [3] where N is independent of ? and thus depends only on r. Nb is the tangential displacement where b is the Burgers vector. Since U? is a linear function of r, then N must be a linear function of r. If a2 is the outer radius and a, is the inner radius to which the plastic deformation has extended, then N = Nm2 r-a1 [4] This function meets the conditions that at

Jan 1, 1956

By Arthur Knapp

NO oil territory in the world has been so rich in large producing wells, in a comparatively small area, as the Baku field. Particularly is this true of the Bibi Eibat field, which formerly produced millions of "poods " of " gusher," or as it is called in Russia, "fountain" oil. The Bibi Eibat and Balachany fields have been exhausted of gas and ruined by water, but &apos; the Surachany and Benegadi fields are still fountain territories and: many outlying districts that have only been prospected produce rich fountains. The method of controlling fountains, or gushers, is the result of growth, along with the Russian system of drilling, where large diameters and riveted casing have been in vogue. The screw casing is seldom used except to exclude water. Formerly the method of finishing wells and the condition of the casing at the top of the well would not permit the use of gates, manifolds, and connections as is standard elsewhere. The life of the flowing wells is very short, particularly those 10 in. (25 cm.) or more in diameter, which produce large quantities of sand and often flow for but a few days and are then a complete loss. More than 1,000,000 poods in 24 hr. have been claimed in several instances, but in no case was the flow for more than a few days. The oil sands of this district are free uncemented sands and vary in thickness from paper thin to a maximum of 10 ft. (3 m.). The sands are interlaid with strata of soft clay. In spite of this, the practice has been to drill into such sands and produce from the open hole without screen or liners. Sometimes the casing is set below the oil sand but in this case holes from 21/2 to 3 in. in diameter are drilled opposite the oil sand, which would not have the effect of a screen. Fig. 1 is an outline of the fountain shield ready for the control of a fountain. It is composed of an inner and an outer covering made from rough boards. The framework is made of rough round poles. When a light flow is expected, only the inner lining is built; and when the fountain comes in unexpectedly, it is often possible to build only the outer cover. The bridge is for the purpose of renewing the blocks as they become worn by the flow. The lower block, as here shown, is made of hardwood and is bolted to the crossbeams with brass bolts. The grain end is toward the flow. The upper block, as shown here, is made of cast steel and is also bolted to the crossbeam with brass bolts.

Jan 1, 1921

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By F. W. Glaser, Benjamin Post

A LTHOUGH most transition metals form a wide variety of boride compounds, the existence of only one zirconium boride, ZrB2, had been established prior to this investigation.&apos; The crystal structure and some properties of a hitherto unreported zirconium boride, ZrB12, are described in this paper. Only one other dodecaboride of a transition metal, UB12, has been reported up to the present.&apos; Chemical analysis of the new compound showed 44 pct Zr and 56 pct B, compared with 41 pct Zr and 59 pct B computed for ZrB12. The difference is within the range of error of the analytical method employed. ZrB12 shows marked metallic properties. It is obtained as a fine black powder. Measurements of electrical resistivity were made at —79°C, + 22°C and +64°C. At 22°C the electrical resistivity is approximately 60 microhm-cm. Over this range the temperature coefficient of resistivity is +0.00162. The thermal conductivity at room temperature is 0.122 watts per cm per "C. The product of the electrical resistivity and thermal conductivity is therefore 8.05, which is not far from the normal Wiedemann-Franz ratio (approximately 7.5 at room temperature). These measurements were made on hot pressed samples which were not always high density specimens. The hardness of ZrB12 on the Rockwell A scale varies between 92 and 92.5. Crystal Structure Determination Single crystals of ZrB12 of a size suitable for X-ray diffraction analysis could not be obtained and powder samples had to be used. Filtered Cu radiation was used throughout. Powder diagrams were indexed on the basis of a face-centered cubic unit cell. After correction for film shrinkage, a Bradley and Jay extrapolation³ to ? = 90" indicated that a, = 7.408 ±0.002A. The volume of the unit cell is 406.5A.V he assumption that there are four "molecules" of ZrB12 per unit cell leads to an X-ray density of 3.63 g per cc. The measured density is 3.7 g per cc (as measured by the immersion method). Relative intensities of reflections were determined by integrating the intensities of diffraction peaks using the count register of a North American Philips wide range spectrometer. Intensities measured in this way showed good agreement with photographic intensities estimated visually using multiple film techniques. The usual Lorentz, polarization, and multiplicity corrections were applied to the observed intensity measurements. There are striking similarities between ZrB12, and UB12. The unit cell of the latter is also face-centered cubic and contains four molecules. a, = 7.473, compared with 7.408 for ZrB12. The radius ratio rB/rU is 0.57; rB/rZr is 0.54. In both ZrB12, and UB12 the four metal atoms in each unit cell are in special positions; only the boron positions need be determined. The latter may be inferred from the extent to which diffraction of X-rays by the 48 boron atoms reinforces or weakens the diffraction by the metal atoms. This effect is relatively much greater in the case of the zirconium compound. In their determination of the crystal structure of UB12, Berthaut and Blum&apos; assumed holohedral symmetry (space group Oh5 , Fm3m) and reported that the U atoms are in positions 4(a): 000; 01/2 1/2; ½ 0 ½ ; ½ ½; the boron atoms were reported to be in positions 48(i) with x = 1/6: ½xx; ½xx; x½x; x½x; xx½; xx½; ½xx; ½xx; x½x; x½x; xx½; xx½

Jan 1, 1953

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing&apos;. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing&apos;, There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry&apos;s law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H&apos; is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

THE 135th meeting of the Institute was the largest and most enthusiastic that has ever been held, sur-passing passing in numbers attending even the notable meeting of 1920. The total registration was 1493. The technical sessions and round tables, 38 in number, were spread through four instead of three days as heretofore in order to reduce the number of conflicts, and most of the A. S. T. M. Committee meetings were held over until Friday. Even so it was necessary to schedule as many as seven simultaneous technical sessions, and there were usually at least two going at once that each wished to attend. Three special luncheons and five group dinners were held, each of which strung out into an informal meeting, and yet approximately 500 came to-gether each day at the general luncheon and over 700 attended the banquet on Wednesday night. The smok-er attracted 402, and the various social affairs under the charge of the general or the women&apos;s committees were all crowded. From 10.00 a.m. Monday to 11.00 p.m. Thursday there was one long series of meetings after which the members went home to catch up on their sleep. The comment on the meeting of a member of one of the other societies, who had occasion to be much in the building, was the markedly friendly spirit of the gathering, the large numbers who were evidently old friends and acquaintances. This does seem to set the miners off somewhat from other engineering groups. So many have shared the same blankets and beans at one time or another that the annual meeting has truly come to be a family reunion.

Jan 3, 1927

By Oliver Halston

THIS paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Proutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work. Lead Metallturgy Popularly Supposed to be Without Problems In bead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that bead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the 3 years of work of the Salt Lake Station, the following classification of problems in the metallurgy of bend has been made: Those involving Oxidized Ores. 1. Ores containing only bead. s. Ores containing bead and silver or gold. 3. Ores containing bead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some bead. 2. Ores of complex zinc-bead-iron sulphides. 3. Complex sulphides containing in addition precious metals.

Jan 8, 1917

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.&apos;

Jan 1, 1970

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By A. H. Daane, B. J. Beaudry

The uranium-antimony system has been investigated by metal-lographic, therma1, and X-ray methods. There are four intermediate phases present: USbz and U,Sb, which undergo peritectic decomposition at 1355°and 1695OC, respectively, and USb and UPSbs which melt congruently at 1850"and 1800°C, respectively. There is a eutectic between U4Sbs and USb which melts at 1770°C. USb,, UsSb4, and USb are line compounds while U4Sbs has a solubility range of approximately 1.5 at. pct at 1770°C. Single crystal studies of the cmpo,und U.,SbS show it to have a hexagonal unit cell with a, = 9.268A and c, = 6.201b;. The solubility of uranium in liquid antimony increases from 0.1 at. pct at 650°C to 1.5 at. pct at 900°C. The solubility of antimony in a, P, and y uranium is approximately 0.02, 0.1, and 0.05 at. pct respectively. IN nuclear reactors, uranium has been used mainly in the form of solid-fuel elements of the pure-metal or uranium-rich alloys. However, in attempts to overcome some of the difficulties inherent in solid-fueled reactors, reactor concepts hive been proposed in which the fuel would be a liquid metal, such as a solution of uranium in another metal. The liquid-metal fueled reactor (LMFR) designed by the Brook-haven National Laboratory of the U.S. Atomic Energy Commission is an example. Fuel for this reactor is a solution of approximately 800 ppm enriched uranium in bismuth.&apos; To design such liquid-fueled reactors, a background of information on the solubility of uranium in various metals is obviously necessary. The present study was undertaken to pro- vide information for such purposes, and in addition, to study the uranium-antimony system as a whole. A preliminary literature search showed that some work had been done previously on uranium-antimony alloys, but no attempts had been made to make a complete study of this system. The solubility of uranium in antimony was studied by Cammack and Bridger&apos; up to 950°C and by Hayes and Gordon up to 900&apos;-C. Their data are plotted in Fig. 1. Ferro, in an X-ray structure study of some uranium-antimony compounds, found USg to be tetragonal with a, = 4.2724 and c, = 8.471A, U3S4 to be b.c.c. with aO = 9.095A and USb to be f.c.c. with a,= 6.191A. Colani reported the compound UsSba; however, work by Ferro and by this Laboratory showed that this compound does not exist. foote&apos; reported several intermediate phases in the uranium-antimony system, but did not identify them. Greninger&apos; re-ported finding an intermediate phase in a 5 at. pct Sb

Jan 1, 1960

By G. Gutzeit

An inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity.4,7-l3 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime&apos;) It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals." Chelate-forming Compounds as Collectors In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxyl-amine (Cupferron) C6H5NO(=NONH4). Holmanl9 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-diox-imes were generally selective collectors for nickel ores. Taurin NH2(CH2)2S03H has been proposed for the concentration Of Oxidized lead ores.19 Diphenylthio-carbazone

Jan 1, 1947

By G. Gutzeit

An inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity.4,7-l3 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime&apos;) It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals." Chelate-forming Compounds as Collectors In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxyl-amine (Cupferron) C6H5NO(=NONH4). Holmanl9 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-diox-imes were generally selective collectors for nickel ores. Taurin NH2(CH2)2S03H has been proposed for the concentration Of Oxidized lead ores.19 Diphenylthio-carbazone

Jan 1, 1947

By R. P. Carreker, R. L. Fullman, J. C. Fisher

CREEP tests are usually constant load tests. As deformation occurs, the cross section of the specimen changes so as to maintain approximately constant volume. Until necking starts, A _ l0 A0 - 1 where A is the cross-sectional area, 1 is the specimen length, and the subscript o indicates initial values. Thus, during a tensile creep test under constant load, the stress increases in proportion to the elongation. A A, 1, where S is the stress and F the load applied to the specimen.

Jan 1, 1954