Search Documents

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By Frank C. Aplleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO4•2H2O) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [Sulfur Combined Lime Trioxide Water (CaO) (SO,) (H2O) Gypsum 32.6% 46.5% 20.9% Anhydrite 41.2% 58.8% -] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product. End Uses The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris (the hemihydrate of calcium sulfate, CaSO4 ½ H2O) which when mixed with water will set or harden as the calcium sulfate returns to the dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uncalcined uses of gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in less developed countries where construction and other industrial uses may be quite limited, the use of uncalcined gypsum for portland cement retarder may well be the dominant-if not the only-market for the mineral. It has often been noted that calcium sulfate constitutes the world's largest reserve of sulfur, and minor use of both anhydrite and gypsum has been made to produce sulfuric acid or other sulfur compounds such as ammonium sulfate. However, because sulfur is readily available at lower cost from other sources, use of calcium sulfate has been limited to only a few locations where it could compete economically. No such use is reported in the United States at this time. Mineralogy Anhydrite, CaSO4 because of its geologically rapid conversion to gypsum, and relatively high solubility (about 0.2 g per 100 g H2O) is not often found outcropping in climates wet enough to support abundant vegetation except on steeply dipping slopes or other places where hydrated material is continuously removed. Anhydrite rock is most often light to bluish gray in color, and under the microscope, varies

Jan 1, 1983

By G. C. Mudd, E. J. Myers

Within the last 15 years David Brown Gear Industries has manufactured approximately 200 large mill gears over 6m diam., 58 of them over 9 m and up to 12 m diam. The experience has not been without problems, due to a lack of clear understanding of the loads and stresses imposed on large gear wheels. American Gear Manufacturers Association (AGMA) practices suggest that a service factor be used for mill gears. But what is meant by "service factor"? The layman might be forgiven for believing that the term is synonymous with "safety factor," but this is certainly not true. The service factor is an aggregate of the following in some proportion: -An application factor, i.e., an allowance for the fact that systems do not run smoothly with uniform torque. -An ignorance factor covering the imperfections in the basic gear calculation. -Possibly a safety factor. In the following sections some of the ways in which the limits of applicability can be overstepped are discussed.

Jan 1, 1983

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:' I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By George T. Wickes

(Washington Meeting, May, 1905.) SEVERAL years ago, Mr. Robert A. Cook described and illustrated in our Transactions 1 a mechanical coke-drawer, patented in 1891 by Mr. Thomas Smith of the Thorncliff Iron Works, Sheffield, England, and first introduced in the United States in, 1896, at the coking-plant of the Latrobe Coal Co., Latrobe, Pa. This machine has not received any very extended application in this country, although it was successfully used in two places for a number of years. The present. paper describes a new and simpler machine, containing few wearing-parts capable of withstanding continued rough usage. Anything which tends to prolong the general use of bee-hive ovens will be welcome to those who are interested in cheapen¬ing the cost of producing coke in such ovens, especially if it provides satisfactory mechanical means, replacing the hard labor involved in drawing coke by hand with the old-fashioned ?duck bill.? The difficulty of finding efficient coke-drawers, especially during the summer season, and in the South, is notorious. Yet, notwithstanding the great improvements that have been made in retort coke-ovens, new bee-hive ovens are continually constructed; and a machine which will successfully compete with hand-drawing, and, at the same time, add to the efficiency of the bee-hive oven, seems to deserve notice. The machine here described was put in operation at the Frick Coal and Coke Co.'s plant, known as Continental No. 1, at Uniontown, Pa., in October, 1904, and is reported to have met successfully all the tests to which it has been subjected. This trial has demonstrated that one of these machines, equipped with an electric motor, and operated by one mart with an assistant, besides two men to " water down " the

Jul 1, 1905

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy's law and material balance relations can be written as follows.

By D. Harker, M. J. Murphy

The mechanism by which age-hardening takes .place is still not completely understood. The principal theories range from the extreme of "precipitaiion-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. Preparation of Formvae. Replicas of Metallic Specimens This section is concerned with the techniques that have roved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. it is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work—very fine polishing and etching with very dilute solutions—is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. Preparation of Metallographic Specimens The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch—to approximately the depth necessary for a micrograph at 1000 diameters—usually produces a sur-

Jan 1, 1945

By Francis O. Blackwell

There are few industries in which power is more important to successful operation than mining, and none in which it is so difficult to ohtain power cheaply. Fuel is usually expeusive in mining districts, ana the ma chinery may be widely scattered and located in places difficult of access. The work is often so intermittent and variable as to prevent the economical use of steam. Mining operations are likely to exhibit accumulations of comparatively small and inefficient engines, numerous boilers and long lines of wasteful steam-pipes. Conlpressed air, as a means of transmitting power, is so handicapped by losses in the compressors and piping that it is limited to short distances and to the operation of apparatus requiring power, without regard to cost. To-day, electricity is rapidly replacing other methods of power-distribution, primarily because it is practically independent of distance. By selecting a potential proportional to the length of transmission, the cost of electric conductors and the e5ciency are the same for all distances within reasonable limits. For instance, a given amount of power can be delivered either 528 ft. away at 100 volts, or 50 miles at 50,000 volts, with the same total of copper per H.P. and with exactly the same loss of power in the transmissioo-circuk. This independence of distance permits the selection of the place most advantageous for power-development as a site for an electric power-plant, and the co~~centration there of the generation of all the power required within a radius of many miles. The powel.-site may be at a fall of water, if one is available, or a steam-plant can be built where fuel and supplies are cheapest, or where suflicient water is available for boiler-feed and condensing purposes.

Jan 1, 1904

By Chung Yu Wang, Guy C. Riddle

There are found in nature upward of II2 minerals containing antimony, but only a few of them, listed in Table I, can be considered as antimony ore-forming minerals. Stibnite (Sb2S3), antimony sulphide or glance, is the principal ore of antimony. The oxide ores—cervantite, kermesite, valentinite, sernarmontite—occur sparingly in nature. Dry methods are generally adopted for the extraction of the metal. Electrometal-lurgical methods have had much attention in America and Germany and have not yet found, on economic grounds, practical or extended application, except in a few places. During recent years, treatment of the poor grades of the ore, especially sulphide, by ore-dressing methods, has commanded some attention and been adopted at a few plants. The impure sulphide of antimony, resulting from the liquation process, is called lLneedle," "liquated" or "crude" anti- mony, and the refined metal itself is called antimony "regulus." The different processes for the treatment of antimony ores are shown in the diagram of Fig. I. Liquation of Crude Antimony The first step in the smelting of antimony is a simple one, the process of LLliquation," which produces crude or needle antimony. Ores containing $ 50 per cent Sb are used in the liquation process for the production of crude. The temperature required for liquation is between 550' and 600°C. Ores to be liquated are broken to about walnut size. If the pieces are larger than this, the low heat used will not penetrate' effectively, and if they are smaller the ore tends to pack too closely for adequate penetration. A packed charge also prevents the free escape of the fused sulphide. Intermittent Liquation in Crucibles The unique type of furnace that is in use in China for smelting is not highly efficient but is simple in construction and operation. The furnace is generally built

Jan 1, 1944

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of the gaseous, topo-chemical reduction of porous hematite spheres. Gas-solid reduction is permitted at each of three advancing interfaces and is controlled by a complex series-parallel sequence of chemical and transport steps. Despite the fact that transport resistances are significant to the advance of each interface, little deviation from linear advance is predicted for the first 98 pct of reduction. Calculations to predict the movement of magnetite /wustite interface by a solid-state diffusion mechanism have been incorporated into the earlier dense-pellet model.' The porous-pellet model is found to give a better description than the dense-pellet one for McKewan's measurements2 of interface movements in dense polycrystalline hematite reduced in hydrogen-water vapor mixtures. THIS paper reports a continuation of work"3" directed toward the better understanding of gas-solid reactions and the development of mathematical models that may be helpful in the design or control of ore-reduction processes. Laboratory studies of the reduction of single oxide samples in tube furnaces normally employ an abundant excess of pure reducing gas. Reduction may appear to be adequately described by a model assuming gas-solid reaction solely at the iron/wustite interface.''' However, when iron ore is reduced in either a fixed bed or an efficiently operated counter-current column, there are portions of the bed where the partially spent gas is no longer capable of reducing wustite to iron. Nevertheless, the formation of the intermediate reaction products, wustite or magnetite, can and does continue. In order to account for this aspect of the reduction of beds of particles, three semiempirical mathematical models were devised.' One of these was for the limiting case of completely dense particles, and two alternatives were provided for porous particles. For purposes of the analysis, a dense pellet was defined as one in which the wustite and magnetite layers were impervious to the reducing gas when the atmosphere was capable of forming iron. In a porous pellet, the intermediate product layers were assumed to be sufficiently permeable to allow reducing gas to penetrate beyond the iron/wustite interface to form wustite and magnetite by removal of oxygen as a gaseous product rather than by a solid-state redfiction mechanism. Further progress required a better understanding of the reaction of the individual particles with the gas stream. A comprehensive mathematical treatment was developed' to describe the continually changing interplay of transport and reaction steps

Jan 1, 1967

I. N. KNAPP, Ardmore, Pa. (written discussion*).-Captain Lucas has made an important contribution to our, knowledge of Belle Isle, especially as to the outline of the sulphur deposit, and the pronounced irregularity of the salt surface. I agree with his view, that the elevation or mound that constitutes Belle Isle may consist of several salt domes formed at different periods. It may be interesting to note the high gas pressure encountered in pockets in the salt by my No. 1 Belle-Isle well. While drilling a dry hole with cable tools, we sometimes struck. pockets of gas which would float the tools, so that drilling had to be suspended sometimes for several hours at a time, until the head of gas was exhausted, and this with a string of tools, 5-in. (127 mm.) stem 36 ft. (10.9 m.) long, that weighed complete about 3500 lb. (1587 kg.). At about 1800 ft. (548 m.), we struck the largest gas pocket and the string of tools was thrown up and nearly out of the hole. When it dropped back it made several loops

Jan 1, 1918

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By H. Y. Hunsicker

A graphic method has been devised for three-di-mensional analysis of hot deformation and for correlating the amount and directionality of the deformation with resulting directional properties. Deformation is evaluated in terms of dimensional change ratios referred to three orthogonal axes. Since all combinations of the three ratios can be represented in a triangular coordinate field with logarithmic scales, a two-dimensional chart of extent of deformation and degree of asymetry is possible. The entire gamut of shape changes from upsetting through flat-rolling to rod-rolling is accommodated. The resulting coordinate system is a base upon which can be represented the properties of the wrought products measured in the directions of the axes employed fir evaluating the deformation. When property data are available for many types and amounts of deformation, a three-dimensional figure can be constructed, and the projection of this figure is referred to as a ''3d'' chart. Experience in using such charts to plan fabricating operations for a variety of thick-section forged and rolled products of heat-treated aluminum alloys has verified its practical value for optimizing directionality relationships. MechANICAL anisotropy of thick section products of heat-treatable aluminum alloys is recognized by producers and users of these products, and the extent of the directional differences is apparent in property tabulations included in handbooks, standards, and specifications.' Attention has also been directed to the existence of important directional differences in the resistance of these products to stress-corrosion cracking. Metallurgical structure factors responsible for these directional differences include, among other possibilities, shape and alignment of grains, voids and nonmetallic inclusions (when present), volume fraction and spatial distribution of secondary phase particles and solid-state precipitates, crystal-lographic textures, and Bauschinger effect. The contributions of the individual factors vary with alloy composition, heat-treated temper, type of working process (forging, rolling, extrusion), and the amount and directional nature of the deformation. In general, the cast ingot used as the starting material for producing these wrought products exhibits only a modest degree of directionality. A monotonic and continuous transition from this nearly isotropic state with progressive hot deformation would appear probable, assuming that the working temperature is sufficiently high to cause continuous dynamic recovery. Several years ago a project was undertaken to evaluate the effects of hot deformation and metallurgical structures on the directionality of thick wrought aluminum alloy products, and the method to be described was developed as an analytical tool in this investigation. DIRECTION NOMENCLATURE The nomenclature system adopted by industry for the three mutually perpendicular directions employed in testing aluminum alloy products includes four terms: "longitudinal", "transverse", "long transverse", and "short transverse". These terms are conventionally related to the external geometry of the product but also by implication to the deformation and resulting metallurgical structure. Occasions arise in which through use of unusual fabricating methods, intentional or otherwise, the structure does not have the usual relationship to external geometry or may be very complex because of inhomogeneity of deformation throughout the piece. The longitudinal direction is generally parallel to the primary rolling direction or to the direction of extrusion. In the case of forging, it is parallel to the direction of maximum extension (not maximum "working" or "flow", as frequently stated). The term transverse is applied to any direction perpendicular to the longitudinal direction in a product having symmetry about the longitudinal axis, and generally, although not always, the deformation to produce these forms is nearly symmetrical in the transverse plane. This term then may be applied to a round, square, hexagon, or other polygonal, symmetrical shape produced by extrusion or rolling or by forging, if produced by a simple, symmetrical drawing procedure. The type of microstructure generally associated

Jan 1, 1970

By AIME

BORN in 1899, in Bridgeport, Conn., E. A. Anderson grew up in a center of the nonferrous metal industry. Perhaps that had something to do with his selection of mining as a career while an undergraduate in Yale. After securing his Ph.B. in mining he worked for a year at Handy & Harman. By this time physical metallurgy had supplanted his interest in mining and he entered the Yale graduate school where he secured his M.S. degree in metallography under C. H. Mathewson. After completing his graduate work he entered the employ of The New Jersey Zinc Co. in their research division where he has remained ever since. The transition from graduate study to industry involved no disruption of technical interests. Academic research relating to the zinc-aluminum alloys, then coming into use for die-casting, was followed by extensive and productive industrial research in the perfection and commercialization of these alloys. Research on rolled zinc and rolled zinc alloys, corrosion and stress corrosion, dry cells, electroplating on zinc, and electrodeposition of zinc followed in overlapping succession as time passed.

Jan 1, 1947

By Carl L. Shapiro, Jerome and Strauss

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Jerome and Strauss, Carl L. Shapiro

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By H. Y. Bassett

THIS paper attempts to show the various major operations used in nonferrous tube mills and does not necessarily represent the current practices at the two plants of the Wolverine Tube Div., of Calumet and Hecla Consolidated Copper Co. Inc. The operations now utilized in the production of tubing are quite varied and show the continual interest and advance metallurgically and mechanically to produce the best quality at the lowest cost. Naturally, any advance or lowering of cost is dependent on large production runs, which mean longer machine running time with maximum worker productivity. Standardization of tube sizes and elimination of unnecessary alloys are therefore very necessary, otherwise the development of costly new production machines would be of little benefit to the consumer as a whole. It should be noted that in such a short presentation it is impossible to describe in any detail the major operations. The short descriptions, it is hoped, will enable all who are interested to obtain a general idea of present, day practices in the copper tube producing field. Fig. I is a flowchart or sequence of operations showing the steps usually employed in tube production. RAW MATERIALS Quality starts with the raw material, and it is absolutely necessary that raw material be controlled and held to rigid specifications. Little need be said, however, regarding the raw materials for the casting of bars or billets, as the material always is purchased and checked against the various governing A.S.T.M. specifications. CASTING Casting, as is indicated in Fig. I, is quite varied and for convenience can be classified into two groups: The casting of solid billets, and the casting of hollow tubes, each of which is the base for subsequent operations. In the melting of the raw materials various types of furnaces are used, and the selection of any one is dependent on many factors outside the scope of this paper. However, as of general interest, a short description will be made of each. Induction Furnace (Low Frequency) This is popular in the melting of copper-base alloys, Fig. 2. In the induction furnace the principle of an inefficient transformer is used for the production of the necessary melting heat. The primary coil is.arranged around a transformer core made of high permeability silicon steel sheet. The secondary circuit is through a melting channel around the primary coil and opens into a hearth which contains the main charge. The heat is generated only in the melting channel, but because of the stirring action there is a constant flow of metal around the channel, which when mixing with the charge causes very rapid melting. The volatilization losses are very low as the furnace atmosphere above the charge is heated only by the heat from the melting metal. The stirring action, however, makes the use of any slag cover difficult. Such furnaces- must be started with molten

Jan 1, 1951

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952