Search Documents

By E. J. Fasiska, H. Wagenblast

The dilalion of a ivon by interslilial carbon was measured by two independent techniques —dilatometric mesurements at 719 c and X-ray measurments of the urlil cell parameters a1 room temperature after quenching. The relative expansion per increase in cavbon content by both methods is (2.9 + 0.3) x 10-3 pev at. pcl C nrzd is temperature- independent within experimental error. This corresponds to (6.3 5 0.6) cu cm per g-atom for the partial gram-atomic volume of carbon in a iron-only slightly smaller than the atomic volume for iron in the same temperature vange. THE only previous quantitative study of the dilational effect of carbon dissolved in a iron was performed in 1934 by Burns1 which, at the time, generated some discussion of possible sources of experimental error.2 For a system of such widespread importance, we felt that a new investigation was merited. Both X-ray diffraction and dilation measurements were used to determine the expansion of the a iron lattice by dissolved carbon, avoiding as much as possible any previous experimental problems and deficiencies. The dilation method at solution temperature offers not only measurements which are free of residual strain but also, in conjunction with the room-temperature X-ray measurements, a method to detect any large temperature dependence of the partial gram-atomic volume of carbon. To insure that quenching strains did not affect the room-temperature X-ray measurements, wire specimens of constant carbon content but different diameter were examined for such an effect. SPECIMEN PREPARATION The material used for both experimental techniques was "Ferrovac E" iron received in the form of 19-mm-diam rod and stated as having the following impurity contents: C, Cr, Cu, Mn, P, and V, each in the range of 10 to 50 ppm; Co, O, Mo, S, and Si, 60 to 100 ppm; W, 200 ppm; Ni, 230 ppm; N, 4 ppm. The stock material was cold-swaged to 0.71 mm diam for the Debye-Scherrer X-ray camera specimens and portions were cold-rolled from 6.3 mm diam to 0.79- and 0.25-mm sheet for X-ray diffractometer and dilation measurements. The wires were annealed in wet hydrogen for 6 hr at 840°C and 15 hr at 720°C, and then quenched into 0°C water. A chemical analysis for carbon after this treatment gave 0.0046 + 0.0014 at. pct C. Three portions of these wires were subsequently held at 719°C in three different hydrogen + methane mixtures and then quenched, resulting in carbon concentrations of 0.0283, 0.0598, and 0.1067 at. pct C by chemical analysis. After carburizing, the wires were swaged to 0.48 mm and electroplated with silver to prevent carbon loss during subsequent heat treatment. The final heat treatment consisted of holding the wires at 72 1°C for 5 min in a He-2 pct H mixture followed by quenching into 0°C brine. The wires were held at room temperature for a few minutes to remove the silver plating using a phosphoric acid-hydrogen peroxide solution, and then stored in liquid nitrogen until the measurements were made. EXPERIMENTAL TECHNIQUE A) Dilation Measurement. The dilatometer consisted of a gas-atmosphere vertical tube furnace modified so that length changes of a ribbon-shaped specimen could be measured externally. This was done by installing a gas-tight mercury seal at the top of the furnace as shown schematically in Fig. 1. The specimen (21.0 cm long, 1.27 cm wide, and 0.25 mm thick) was suspended in the center of the furnace by 3-mm-diam quartz rods with the upper one passing through the cap of the mercury seal. Above the cap, the upper quartz rod was coupled to a lever exerting a load of about 25 g (-12 lb per sq in.) on the specimen and having a 10 times mechanical magnification. The vertical position of a marker at the other end of the beam was read with a traveling microscope with a precision of 0.01 mm. The temperature gradient of the furnace was meas-

Jan 1, 1968

By Herbert Clark Hoover, Lou Henry Hoover

DIGGING of veins I have written of, and the timbering of shafts, tunnels, drifts, and other excavations, and the art of surveying. I will now speak first of all, of the iron tools with which veins and rocks are broken, then of the buckets into which the lumps of earth, rock, metal, and other excavated materials are thrown, in order that they may be drawn, conveyed, or carried out. Also, I will speak of the water vessels and drains, then of the machines of different kinds,1 and lastly of the maladies of miners. And while all these matters are being described accurately, many methods of work will be explained. There are certain iron tools which the miners designate by names of their own, and besides these, there are wedges, iron blocks, iron plates, hammers, crowbars, pikes, picks, hoes, and shovels. Of those which are especially referred to as " iron tools " there are four varieties, which are different from one another in length or thickness, but not in shape, for the upper end of all of them is broad and square, so that it can be struck by the

Jan 1, 1950

Flaubert, as we know, laid stress on the selection of the right word, le mot juste, the precise epithet, the word that belongs to the thing. A sentence, or even a paragraph, may be spoiled. by the use of a word that is not proper, that does not fit or is foreign to the meaning intended. An Australian mining expert is reported to have said: You have a property of considerable value, and what I saw warrants s good development of very rich cubicular galena, with gossan intermixed. 'Cubicular' means 'belonging to a small bedroom', a 'cubicle' being a sleeping compartment. He meant 'cubic', of course. This is a malapropism, and reminds me of the lady from Chicago that, on her return from Europe, said how much she had enjoyed the rural parts of France, because, among other things, it was "so delightful to hear the French pheasants singing the mayonnaise to the tune of the Los Angelus". It is impossible to amalgamate coal-tar thoroughly with the pulp in the agitating-tank. In metallurgy, 'amalgamate' refers to the combination of mercury with one or both of the precious metals, forming an amalgam, which is an alloy of mercury with another metal. It differs from other alloys, such as brass or bronze, in being made without the aid of heat, inasmuch as mercury is molten at the ordinary temperature. The word comes to us from the Greek through Old French and means 'something soft'. It is a mistake to use technical terms, having a specific meaning, for purposes that are foreign to that meaning. The writer of the quotation is not discussing any combination of metals; he is dealing with the physical process of mixing and is using 'amal-

Jan 1, 1931

By L. J. Klinkenberg

It is pointed out that the current concept of pore size distribution is not unequivocally defined and that different methods aiming at a determination of such a distribution therefore do not lead to the same results. A pore size distribution should not be based on the idea that a core should, under all circumstances, behave as a bundle of straight non-interconnected capillaries of the same pore size distribution. This is illustrated by calculations and experiments on the displacement of miscible liquids. INTRODUCTION The introduction of the concept of pore size distribution has been an attempt to characterize the intricate geometry of the flow channels in porous media. As pores in a porous medium are interconnected it is impossible to describe exactly what is meant by a "pore" and, therefore, the term pore size distribution requires further amplification. In the visual method for the determination of pore size distribution "the pore" is considered to be the hole between the grains as observed on thin sections or on a polished surface of the rock under a microscope. In all other presently known methods,1,2 a displacement process is studied and it is ascertained what as- semblaae of straight cylindrical capillaries would show the same behavior. The distribution of the capillary diameters of this assemblage is said to represent the size distribution of the pores of the actual porous medium. From the foregoing it is already apparent that it is useless to try to decide which process or which method of investigation leads to a "correct" pore size distribution. To illustrate this further a displacement process in which a fluid is displaced by another miscible with it will be discussed and the results will be interpreted in terms of a pore size distribution. DISPLACEMENT EXPERIMENTS WITH MISCIBLE LIQUIDS OF NEARLY IDENTICAL VISCOSITY AND DENSITY Interpretation in the Form of a Pore Size Distribution If distilled water is displaced from a homogeneous unconsolidated sand pack by, for instance, a dilute solution of NaCI, the breakthrough recovery i.e., the amount of distilled water produced at the moment the first trace of NaCl can be detected in the effluent water, is between 95 and 100 per cent of the pore volume of the pack. This result can be understood by following in imagination the course of one particle of the liquid. Imagine a length, ?l, at the end of which a liquid particle has an independent chance of a renewed choice of pores of different diameters. In other words, the particle has a choice of traveling time, at, for any length ?l; instead

Jan 1, 1958

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By Frank Firmstone

The material described below was made at Furnace No. 2, Longdale, Va., Oct. 28, 1907, during a sudden derangement of working, in the course of which the furnace became entirely bridged over and for some time no solid material whatever descended into the hearth. This caused the hearth to become so completely emptied that, at the tuyere-level, a pricker put in at one tuyere could be seen by looking in at the opposite one. The tap-hole was opened and the iron got out with some difficulty. It ran sluggishly, throwing many sparks, but was not too thick to run into the chill-molds. Naturally, the product was assumed to be white iron, which is almost always produced under similar circumstances; but on removal front the molds it proved to be very strong and tough, although full of blow-holes. Most of these blow-holes bad bright, unoxidized walls. The iron could be drilled by using a "special steel" drill, the drillings curling up similarly to those of steel. An analysis by P. W. Shimer of this unusual product gave: Si, 0.019; P, 0.228; S, 0,39; Mn, 0.042; C, 2.366; and graphite, 0:000 per cent. A cast of iron made just before the disturbance contained P, 0.98, and Mn, 1 per cent. The peculiar product seems to have been decarburized in the hearth and, at the same time, to have lost much phosphorus and manganese, either by the action of the blast in the empty hearth, or, more probably, by. contact with the cinder rich in iron which was formed at the time. Unfortunately, no specimen of the cinder was preserved, so its composition cannot be given. It seems very remarkable that, with the furnace in bad condition, the temperature should be high enough to keep such

Sep 1, 1908

By W. R. Ingalls

THE present administration has made sincere and effective efforts to reduce the expense of the Federal Government, but it has reached a point beyond which it seems impossible, or anyway extraordi-narily difficult, to go. This is ascribable to the large part of the budget that is represented as war expense. There is no doubt that this spells high taxation for many years to come. Nevertheless, although a large part of the taxation will be attributable to the war, the paying out of the proceeds of that taxation by the government will not be war expense, except in minor part, as will be hereinafter made clear. It will be useful to explain the economic meaning of this situation, for it has bear-ings upon several open questions, such as a bonus to the ex-soldiers, the foreign debt accounts, etc. The expense of the war on the part of the American people was in the main paid concurrently with its prose-cution. This was necessary. Warfare is not conducted with money, but with materials and labor. Except for such previous production as was represented by stocks of goods, the requirements had to be supplied by coincident production. With the end of 1918 our war expense ceased, save for such production, e.g., of ships, that was allowed to run on unchecked, and the indemnities that had to be paid for cancelled contracts. When those matters have been settled we shall be done, barring one important thing. Of course, our war expense began to contract right after the armistice and shrunk rapidly with the demobilization of the troops in 1919. If we had not been able to obtain all needful material from our own sources and had been constrained to borrow it from foreign countries, incurring a foreign debt, we should have been in the quite different posi-tion of having to repay that material, or its equivalent, during subsequent years. The European countries had to come to us for such supplies. This outlines the fundamental difference between their present situations and ours. We were therefore compelled not only to furnish materials and man-power for our own warfare but also much for the Allies.

Jan 3, 1923

By Leonard Greenburg, William B. Harris, Gustäv Werner

HAULAGE in tunneling operations generally has been done with electric locomotives. As a rule, on short hauls the source of electricity is a storage battery mounted on the locomotive, which, of course, must be removed and recharged periodically. Where the distance from the recharging point to the tunnel face is very long, and where loads are heavy, trolley-driven locomotives are used. Diesel engines have been used in mining and tunneling operations in Europe for a number of years. The recent reports of studies in Belgium1 and by the Bureau of Mines in this country2-4 have indicated the potentialities of this form of power for haulage, mucking, bulldozing and many other underground operations. The hazards attending the use of Diesel engines in more or less closed spaces have long been known. The exhaust constituents that may create a harmful or objectionable environment are carbon monoxide, oxides of nitrogen and sulphur, carbon dioxide, aldehydes and smoke. Lack of precise information regarding the concentration of these gases and the ventilation requirements to reduce them to safe levels has to some extent suppressed their general acceptance in tunneling and mining work. Not until the work of the Bureau of Mines referred to above, and certain experience gained in the construction of the Delaware Aqueduct,‡ has there been available the requisite information regarding the conditions under which their use may be permitted. This paper concerns itself with the successful operation of Diesel engines underground in the construction of certain parts of the Delaware Aqueduct, and describes the conditions under which Diesel engines have been found to operate with a minimum production of noxious gases. The test data reported were obtained during the operation of Diesel engines over a period of two years.* STUDIES BY THE NEW YORK STATE DEPARTMENT OF LABOR Exhaustive tests were made by the Division of Industrial Hygiene, of the composition of the exhaust gases given off by a Diesel engine mounted on. a test block. These tests showed that certain quantities of the gases are discharged from the exhaust. On the basis of these figures, preliminary requirements of design and control

Jan 1, 1942

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately A 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carban content almost as high as the good anthracite, it is not

Jan 1, 1943

By A. L., Bailey

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally.

Jan 1, 1949

By AIME AIME

MINING geology has been at once the vocation and avocation of John M. Boutwell, newly elected Director of the Institute representing Utah and Colorado. Geologists were looked at askance by most of the "big" men in mining when, from 1896 to 1900. Mr. Boutwell was teaching geology at Harvard, his alma neater; and his success in applying geologic principles to the business of finding ore contributed much to changing the attitude of scepticism. From 1900 to 1908 lie was with the U. S. Geological Survey, with service in Bingham, Utah; Morenci, Ariz.; and Park City, Utah. Since then he has been engaged in private practice as a consulting mining geologist retained by many of the leading mining companies. A dozen men now recognized as outstanding geologists got their early

Jan 1, 1937

By Charles Bell

THE Telluride mining district of southwestern Colorado is defined by the 37° 45' and 38° parallels of latitude and 107° 45' and 108° meridians of longitude. Telluride was never a boom camp, but has had a steady growth. In recent years, notwithstanding the business depression of 1920, the business has been the same as in normal years. The first prospector is said to have appeared in 1875, in which year locations on the Smuggler vein were made. Shipments were made in 1877 and 1878, and in 1879 milling the ores was attempted. While the district produced high-grade ores, it did not become important until 1890, when the Rio Grande Southern R. R. was completed from Ridgway to Telluride. The railroad has since been extended to Durango. In the fall of 1896, 400 stamps were in operation, and the annual production was $3,000,000.00, two-thirds of which was gold. The total production from 1875 to 1923 was: Gold $58,274,527; silver 41,830,920 oz., valued at $31,016,893; copper 15,258,866 lb., valued at $2,533,291; lead 166,056,484 lb., valued at $8,324,910; zinc 18,141,182 lb. valued at $1,323,787; or a total production of $101,473,408. All: claims are held in fee. Most of them are 1500 by 300 ft. but claims located within the last few years are 1500 by 600 ft. General supplies are obtained at Telluride, Denver, and Salt Lake. The largest mines are within 6 miles of the town of Telluride. Denver is 422 miles and Salt Lake is 439 miles, by rail, from Telluride. One-half of the distance to Denver and one-sixth of the distance from Telluride to Salt Lake is by narrow-gage railroad. The labor is efficient. The best miners are Italians and Austrians, then Slavs, Greeks, and Mexicans follow in the order mentioned. There are no labor unions. There are no serious mine pumping problems, the drainage being through adits. The Tomboy and Smuggler companies pump water from their reservoirs, the former for, milling and domestic purposes and the latter for milling, power, and domestic purposes.

Jan 2, 1924

By A. A. Burr, D. G. Ebeling

The effects of casting texture, grain orientation and grain size upon the performance of Alnico permanent magnets is described. Single-crystal specimens were produced by special sintering and grain coarsening techniques to study the effect of crystal orientation. In addition to texture and orientation effects, an analysis of the results indicates that the permanent magnet performance is impaired by a refinement of the grain size. AN excellent historical review of the development of Alnico permanent magnets has been prepared by Bozorth.1 The desirable permanent magnet characteristics of Fe-Ni-A1 alloys were discovered in 1932 by Mishima.2,3 The work of Ruder' showed that the alloys were age-hardenable, and Betteridge5 defined the best composition and heat treatment for the magnetically isotropic alloy known as "Alnico 3." Horsburgh and Tetley0 increased the energy product by the addition of cobalt and copper, "Alnico 2," and Oliver and Sheddon7 demonstrated that cooling in a magnetic field improved the residual induction of this alloy. Jonas8,9 then disclosed the great practical benefits of heat treating an alloy of higher cobalt content in a magnetic field and the resulting alloy, "Alnico 5," has become the standard of the industry. This paper describes the fundamental aspects of a procedure which can be used to further improve the properties of these anisotropic permanent magnet alloys. A study of the casting techniques used in the production of anisotropic Alnico permanent magnets indicated that the magnetic quality was affected by the as-cast macrostructure. Improved performance was observed in magnets containing a high percentage of columnar grains whose long axes were parallel to the magnetic axis of the casting. McCaig10 studied the effect of such columnar grain structures upon the magnetostriction characteristics of similar alloys, however no data was presented showing the effects on other magnetic properties. The following paragraphs describe two experiments which were conducted to determine the effect of various grain orientations upon the energy product. Special composite molds were prepared of highly conductive and highly refractive components to remove the heat of solidification from the casting in a controlled manner. Representative macrostructures produced by these techniques are shown in Fig. 1, along with the relative volumes of favorably oriented columnar grains. The alloy, Alnico 5, has the highest permanent magnet performance of any commercial magnet material. It has the nominal weight composition of 8 pct Al, 14 pct Ni, 24 pct Co, 3 pct Cu, and 51 pct Fe. A heat of this material was cast into molds producing the type A and B grain structures shown in Fig. 1 and pairs of the resulting magnets were placed in heat-treating boats so as to eliminate any biasing effects of boat position. After a standard heat treatment the type A magnets, with 16 pct of the volume composed of favorably aligned grains, had a maximum energy value of 3,940,000 gauss-oersteds, while the type B magnets with 73 pct aligned grains averaged 5,090,000. This large im-

Jan 1, 1954

By H. W. Morse

The experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a 40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdalel and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work. Preliminary Tests by Mb. Croasdale Preliminary tests were begun by Stuart Croasdale in July, 1912. A number of important points were definitely decided by his work. Among these were: 1. New Cornelia oxidized ore, not very finely crushed (to about 2-to 3-mesh) showed good extraction with 5 per cent. sulphuric acid. It appeared that better than 80 per cent. extraction could be expected. 2. The consumption of acid for this extraction was not prohibitive. It was apparently 3.5 to 4 1b. gross per pound of copper recovered.

Jan 1, 1917

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

By John Birkinbine

Through the partiality of my fellow-members I have been able, during seven years' service on the Council of the American Institute of Mining Engineers, to note the development of technical societies, a subject which commends itself as an appropriate theme for me, in retiring from the office of President, at a time when we meet in convention with Canadian technical societies. Our next assembly, called at Chicago at the time fixed for an International Engineering Congress, offers additional reason for the selection of this topic. If subsequent statements appear to give to the American Institute of Mining Engineers greater prominence than to kindred organizations, they may be excused upon the ground of long association with and loyalty to its members, and to a personal knowledge of their work. Besides, data as to its growth and development are more accessible; and at a meeting of the Institute features connected with it may be considered as of greater immediate interest than those affecting other organizations. The purpose of this address is, however, to use the record of the Institute as indicating a similar development of other technical societies, rather than to claim preeminence for any organization; the work of each must speak for it. There is a general tendency to form associations at the present time. Organizations have been created and are active in every profession and in all branches of labor, trade, industry, commerce, manufactures, science and art. A record of such associations and their aggregate membership would be startling, and would show how large a percentage of the population of North America is connected with one or more of them; but the figures cannot be even approximately estimated. The class of associations representing national, state, or local trade interests, such as boards of trade, chambers of commerce, etc., may be used as an illustration. A late report shows that in the

Jan 1, 1893

THE morning session on non-metallic minerals was opened briefly by the chairman, Oliver Bowles, giving the usual instructions and then turning immediately to the introduction of the speakers. "Min-ing and Preparation of the St. Peter Sandstone in' Arkansas" by D. D. Dunkin was first presented by W. M. Weigel, mining technologist for the Missouri Pacific R. R. The paper covered a discussion of the geology of the sandstone, correlating it with the sand-stones at Klondike, Mo., and at Ottawa, III. Its physical appearance, structural characteristics and thickness; the mining methods, blasting, loading, haulage and classification were taken up. A series of slides aided in clarifying the details. The discussion consisted of questioning Mr. Weigel on operating details. The second paper, "Geology and Mining of Diaspore and Flint Fire-Clays of Missouri," written by H. S. McQueen, geologist with the Missouri Bureau of Geology and Mines, and C. R. Forbes, professor of mining, Missouri School of Mines and Metallurgy, was presented by Mr. Forbes. It thoroughly covered the geology, stressing the peculiar sink formations in which all diaspore clay deposits of the region occur. The crudeness of the mining methods was mentioned and believed justifiable because of the small size of the indi-vidual deposits. It was stated that the diaspore and flint clay deposits of Missouri were confined to an area 60 mi. square and it was found in a survey that the average deposit had dimensions comparable to the fol-lowing: 100 ft. long, 75 ft. wide and 50 ft. deep. The largest deposit found was 800 ft. long. 500 ft. wide and 20 ft. deep. It is estimated that the known reserve of clays is from 750.000 to 1,500,000 tons. Mr. Forbes stressed the fact that in mining clays the major problem is entirely one of sorting. This is done under the supervision of a pit foreman trained to make this classification by eye. The mine-run clays are sepa-rated into diaspore clay ranging in alumina content from 70 to about 85 per cent, first grade Burly clay 00 to 70 per cent, and Flint clay 52 to 60 per cent. Discussion of the paper consisted in questioning Pro-fessor Forbes on labor. cost, haulage, drilling, and geology.

Jan 3, 1928

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

The week of Sept. 22, will be a week of convocation of societies in Chicago with the exposition of Chemical industries. The American. Institute of Mining and Metallurgical Engineers will occupy the stage for most of the week, American Ceramic Society meets on Wednesday, the American Electrochemical Society on Thursday, Friday, and Saturday, and the Technical Association of Pulp and Paper Industry from Wednesday to Saturday. There will also be a symposium upon Safety in the Plant and Mine under the chairmanship of M. L. Leopold, Safety Engineer of the U. S. Bureau of Mines, and in the evening after this sleeting-which will occupy an entire afternoon-there will be shown a series of motion pictures of safety work in plant, field-and mine. The motion picture program will consist almost entirely of films now being made. Even in motion pictures, the Exposition is outstanding as the place of introduction to the public of the newest and most recent developments. Each improvement of the projectoscope in motion-picture projection has been reserved for first public demonstration at the Exposition. Mention cannot be made of the new exhibits that are engaged for the Exposition, other than to say that the electric furnace will be in operation. These will give, probably for the first time, men of science an opportunity to see and compare the various designs and judge them for the various work to which they are applicable.

Jan 8, 1919