Search Documents

By Charles Catlett

The terms " developed " and " undeveloped " are necessarily relative and cover a wide range; but the latter is here applied to cases in which the information at hand falls short of a clear demonstration of values, and conclusions must be reached frorn a study of the geological conditions of the particular deposit, interpreted in the light of similar and closely-related deposits. Such an inquiry might be characterized as an effort to reach reliable conclusions from insufficient data. But the engineer

Jan 1, 1909

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By Wilbur A. Nelson

In 1839, Gerard Troost,1 the first State Geologist of Tennessee, reported the occurrence of zinc ores in east Tennessee, in connection with the iron ores at Embreeville; in 1844,2 he refers to the zinc deposits of east Tennessee, especially the apparently rich deposits occurring in Jefferson and Claiborne Counties, while his ninth annual report 3 s a description of the zinc deposits of Jefferson County and a description of the most improved processes by which zinc is extracted from its ores. Yet, only during the last few years have these ores been successfully worked. As far as can be learned, prior to the systematic development of the Mascot district in 1911, no large-scale or successful operation of any of the zinc deposits was carried on. But in that year, after several companies had made considerable progress in developing the Mascot area and had proved a relatively extensive body of low-grade sulfide ore, the American Zinc Co. entered the field. It introduced modern methods of prospecting and mining and from the first was successful. Too great credit cannot be given this company for its pioneer work in a previously unimportant field. Throughout the history of its operations, the American Zinc Co. has confined its efforts to underground mining of the sulfide ore, sphalerite. This company has found that successful results in zinc mining in east Tennessee can be achieved only by expending large sums in prospecting and blocking out bodies of pay ore in sufficient magnitude for large-scale operations. At Mascot are located the mines of the American Zinc Co. of Tennessee, the mines being situated along the Southern Railway in the Ilolston River Valley, Knox County, about 13 miles northeast of Knox-ville. At first only open pits, which were worked for oxidized ores, were operated and the production was small. In 1900, the Roseberry Zinc Co. was organized and sank to a depth of 187 ft. what is now known as No. 3 shaft of the American Zinc Co. The upper 30 ft. was in residual clay,

Jan 1, 1925

By Shosei Serata, Bruce Gardner

A system of three new field instruments has been developed to measure, in situ, the three basic classes of geomechanical parameters: material properties, stress state, and creep deformation. The significance of this development is that it represents a successful adaptation of recent computer technology to underground rock mechanics work, opening up new possibilities in underground mining methods. The system was developed to meet the application requirements of the stress control method of mining, a method which is based on the actual geomechanical conditions of the underground, rather than upon conventional linear-elastic, idealizations of ground conditions. These instruments enable in situ measurement not only of elastic, but also post-elastic, yielding, and failure conditions of geological materials, establishing the stress control method on a truly scientific foundation. In order to evaluate the present status of this field instrumentation system, case examples of underground mine openings designed with the stress control method are reviewed and analyzed, in terms of the effectiveness of the three instruments for informing and guiding the site-specific application of stress control design.

Jan 1, 1984

By Walter W. Bradley

Barite, or barytes as it is sometimes called, belongs to one of the lesser groups of nonmetallic minerals, of which 15 to 20 varieties are mined in California in amounts varying in value from a few hundred to almost half a million dollars annually. Commercial production of barite in California, according to the records of the State Mining Bureau (now Division of Mines), began in the year 1910 with shipments totaling 860 tons, valued at $5640 f.0.b. rail shipping point. With the exception of the years 1924 and 1925, when no shipments were made, the output has varied, reaching a maximum of 17,993 tons, worth $90,617, in 1927. The 1928 output was 13,406 tons, worth $55,888 f.0.b. rail shipping point, bringing the state total to the end of 1928 to 59,972 tons, valued at $313,930. Consumption of BaRitE in United States Crude barite sold or used by producers in the United States for the year 1927 amounted to 248,219 tons, valued at $1,594,423, according to the U. S. Bureau of Mines.l In addition, there was imported, principally from Germany, a total of 70,274 tons, valued at $253,284. Manufactured products from these tonnages combined were distributed in 1927 (the latest year for which figures are at present available) as follows: ground barite, 57,658 tons; lithopone, 174,083 tons; barium chemicals (including carbonate, 4,960 tons; chloride, 3,541 tons; binoxide and sulfate or blanc Jixe combined, 13,354 tons). Missouri accounts for nearly 50 per cent of the domestic crude barite, followed by Georgia and Tennessee, with lesser amounts from Arizona, California, Nevada, South Carolina, and Virginia. Occurrence and Uses of Babite2 Barite, also called "heavy spar" and "tiff," is theoretically composed of 65.7 per cent of barium oxide (BaO) and 34.3 per cent of sulfur

Jan 1, 1931

NEW MEMBERS The following list comprises the names of those persons who became members during the period Jan. 10, 1919, to Feb. 10, 1919. ADAMS, FRANCIS SPEARMAN, Supt., Power Dept., Anaconda Copper Min. Co.; Anaconda Mont. ALDERSON, G. E., Min. & Met. Engr 1317 Sloane Ave., Lakewood, Ohio. BENJOVSKY, T. D., Min. Engr., Cons. & Constr 2045 Vine St., Denver, Colo. BROPHY, OSCAR, Met 1523 S. Broad St., Philadelphia, Pa. BUTTRAM, FRANK, Chief Geol., Fortuna Oil Co., 424 Liberty National Bank Bldg., Oklahoma City, Okla. COCHRAN, R. B., Mine Supt., The Teziutlan Copper Co., Aire Libre Puebla., Mexico. CONNAR, T. C., Civ. & Min. Engr. & Geol.; Chief Engr., Zanesville Coal Co., Zanesville, Ohio. DAVE, E. O Capt., Co. A, 212th Engineers, Camp Devens, Mass. FOLEY, CHARLES B., Electro-Met., Martin Rockwell Corpn., 347 Madison Ave., New York,. N. Y. HOSFORD, WILLIAM F., Asst. Tech. Supt., Western Electric Co., Inc., Hawthorne Station, Chicago, Ill. HOSTER, M. T., Supt., French Creek Mines, E. & G. Brooke Iron Co., St. Peters, Pa. KAWASAKI, SHIGETARO, Chief Geol., Geological Survey of Chosen, Government General of Chosen, Keijo. Korea.

Jan 3, 1919

THE Institute of Metals Division of the A. I. M. E. has joined with the American Society for Steel Treating and the American Welding Society in support of National Metal Week in Philadelphia, Oct. 8 to 12. Individual and joint technical sessions, plant inspection trips, and a general exposition to be held in Commercial Museum have all been arranged. With the coming of the Institute of Metals Division into the circle, the scope of the exposition has been broadened to cover non-ferrous metals, and exhibits of much interest are promised. Headquarters for the Institute of Metals and the American Society for Steel Treating will be at the Benjamin Franklin Hotel, and for the American Welding Society at the Bellevue-Stratford. The American Society for Steel Treating and the Welding Society will hold technical sessions each forenoon at their hotel headquarters. The Institute of Metals Division will hold sessions Tuesday morning and Wednesday and Thursday afternoons; that for Wednesday being a joint session with the American Society for Steel Treating. The latter society will hold independent afternoon sessions on Thursday and Friday. Registration and information desks will be open at the hotels throughout the week, and an attractive program of entertainments has been arranged.

Jan 1, 1928

By B. L. Dunic, Terkel Rosenqvist

rr has long been suspected that sulphur has a small but finite solid solubility in iron, but up to the present more accurate data have been lacking. The survey given by Hansen' illustrates the divergence of data and opinions. Solubilities between 0.01 and 1.5 pct have been suggested, and opinions vary regarding the effects of temperature and phase transformations in iron on the sulphur solubility. The extent of solid solution and its variation with temperature might be expected to be an important factor in the occurrence of hot shortness in steel. Therefore, the object of the present investigation was to study this problem more systematically. It was furthermore hoped that solubility data for sulphur might contribute to an understanding of the factors which determine solid solubilities in general. Experimental Procedure The present work was based on the measurement of the chemical activity of sulphur in the solid solution by means of equilibrium with a mixture of hydrogen and hydrogen sulphide. When the solid solubility limit is reached, the sulphur activity in the iron becomes equal to that in the coexisting sulphide phase. A gas mixture of a controlled H,S/H, ratio was passed over pure metallic iron heated to a temperature in the range 900" to 1500". The amount of sulphur absorbed by the iron was determined by analysis, and from a plot of percentage of sulphur vs. gas composition the sulphur activity and the solubility limit were determined. As the rate of diffusion of sulphur in solid iron is very small, often several days were needed to be sure that equilibrium conditions had been established. To produce a gas flow with less than 1 pct H,S of constant composition for several days, was in itself a problem. The most satisfactory arrangement was obtained by a continuous synthesis of hydrogen sulphide from the elements. This was done in the part of the apparatus shown to the left in Fig. 1. The hydrogen used was first purified in tank batches by passage through activated charcoal cooled in liquid nitrogen under a pressure of 150

Jan 1, 1953

NEW MEMBERS The following list comprises the names of those persons who became members during the period of May 10, 1918, to June 10, 1918. ABEEL, GEORGE H., JR., Cons. Min. Engr., .4111 Lafayette Ave., St. Louis, Mo. ALLEN, CARL A Metal Min. Engr., U. S. Bureau of Mines, Butte, Mont. BECKER P. FRANK Engr., Lightner Min. Co., 35 Nassau St., New York, N. Y. BOCK, JAMES H., Steam Shovel Foreman, Chino Copper Co., Santa Rita, N. M. CARRON, FRANK X., Civ. and Min. Engr Rock Springs, Wyo. CROWE, THOMAS B., Mill Supt., Portland Mill, Portland Gold Min. Co., Victor, Colo. DOBSON, PERCY GRENSIDE, Min. Engr. and Geol., Crow's Nest Pass Coal Co., Fernie B. C., Canada. ESTABROOK, W. H., Capt., 3d Bat. 20th Engineers, A. E. F., Care postmaster, N.Y. FRASER, 0. B. J., Engr., International Nickel Co. of Canada, Ltd., Port Colborne, Ont., Canada. GARRIDO,. MANUEL F., Min. Engr 109 W. Myrtle St., San Antonio, Tex. GRODSKY, VLADIMIR ALEXANDROVITCH, Cons. Engr., Motor Products Corpn., Detroit, Mich.

Jan 7, 1918

By Ajoy K. Ghose

INTRODUCTION Longwall mining made its debut in Indian coal mining scene around 1900. Despite this headstart, the application of the method has been slow and halting. Currently, there are some 16 operating longwall faces only in different Indian coalfields contributing to perhaps less than 3 percent of the total underground coal production. Ambitious plans for expansion of longwall mining notwithstanding, apprehensions on the cavability of Indian coalmeasure roof rocks and some unsavoury experiences with face collapses in caved longwalla have impeded wider adoption of the technique. Between 1960 and 1983, some 41 caved longwall faces were worked in Jharia, Raniganj, Karanpura and Korba Coalfields in India, of which 6 faces reportedly had collapsed(1). The first powered support longwall face was started in August 1978 at Monidih colliery which marked a major step forward in the introduction of advanced technological system in Indian coal industry. This paper attempts to analyse critically the experiences with longwall ground control in caved longwall faces in India. Experiences from powered support faces at Monidih, Dhemomain and Pathakhera are synthesized to provide an appraisal of the present status of caved longwall faces under the Indian coalmeasure roofs, which thus far have been characterised as “massive”. The geotechnical site factors at the powered support faces are evaluated and conclusions drawn on the pre-assessment of caving characteristics and support resistance required at the faces.

Jan 1, 1984

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-'Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By J. B. Cohen

EARLY investigators1-4 reported that additions of beryllium to silver caused embrittlement. The in-termetallic phases which are now known to exist5,' were not known at the time. Solidification appeared to occur by a simple eutectic reation.4,7 (The primary beryllium-rich phase appeared globular, when the liquidus temperature was near the melting point of pure beryllium, and angular when the liquidus was much lower; in discussion of Sloman's work,4 it was suggested that this difference was due to an intermetallic compound which was not revealed by the polishing technique.) In the investigation reported here, it was found that if the compounds now known to exist were avoided, certain beryllium-silver alloys containing large amounts of the primary beryllium phase possessed sufficient ductility to be cold formed. Alloys containing 14 and 20 at. pct Ag were prepared from vacuum-cast beryllium containing 1.0 to 1.2 pct impurities and silver, 99.99+ pct pure. The elements were melted together by induction in beryllia or alumina crucibles under argon at less than 1 atm pressure. The cooling rate was adjusted by regulating the temperature of the melt and by reducing the power to zero without stopping the water flow in the induction coils, which were in contact with the crucible. Ingots were about 0.75 in. in diam with a grain size of 0.12 to 0.25 in. Microscopic investigation of transverse or longitudinal sections of an ingot cast from a temperature well above its melting point showed that, in general, the compounds did not form, presumably because of rapid cooling; the alloys consisted of beryllium-rich particles in a silver-rich matrix as shown in Fig. 1. A eutectic structure was not observed, probably .due to the low beryllium concentration of the eutectic composition and eutectic divorcement. Within a given grain, the small globules of the primary phase were all oriented in the same direction, as indicated by examination under polarized light; the orientation varied from grain to grain. This suggested that the globules were branches of the same dendrites. If cooling was too slow, a third constituent was observed in the microstructure; because it formed around the primary beryllium-rich globules it was Fig. 1—Ag-Be alloy, 18.6 at. pct Ag, as-cast. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction. probably the 6 compound. A thin ring around an ingot often contained this constituent. When this compound was present in large quantities, or the silver segregated so that large regions occurred with the beryllium-rich globules in contact, sections from the ingot were brittle. When the compound was initially absent, it was possible to carry out reductions in thickness of 50 pct by cold rolling with only limited edge cracking; failure did not occur until reductions of 80 pct. A typical cross section after cold rolling is shown in Fig. 2. After simple bend tests, microcracks were found; these apparently were difficult to propagate in the two-phase structure, as the specimens continued to behave in a ductile manner after the cracks appeared. Similar cracks would probably be closed during rolling. It is apparent in Fig. 2 however, that the primary beryllium particles undergo extensive plastic deformation. Hardness values of the alloys indicated that some work-hardening occurred during cold working. Fig. 2—Ag-Be alloy, 18.6 at. pct Ag, reduced 83 pct in thickness by cold rolling. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction.

Jan 1, 1961

By Robert Parker

Measurements of the latent heat of transformation from a to 0 titanium were made using a pulse-heating technique. Rapid heating was accomplished electrically by discharging a low-inductance capci-tor hank through a thin-strip specimen. Both high-purity titanium and titanium containing 2700 ppm of 0 were studied. An electrical-resistivity technique and a plot of energy input us temperature rise were used to monitor the phase change. It was concluded that: 1) the latent heat of transformation is 800 i 48 cal per mole; 2) phase change occurred in less than 200 sec; and 3) the percentage phase change that occurs is linearly a function of the energy available for phase change. In addition, this experiment provides a simple and inexpensive method for determining specific heat of electrical conductors over large temperature ranges. The chief advantages of this technique over past pulse-heating experiments are: 1) static measurements of capacitor-bank voltage capacitance and specimen resistance can be made quickly and accurately to determine the energy supplied to the specimen; 2) the specimen is heated so rapidly (10 µ sec) that there is no appreciable heat loss during the heating. THE purpose of this paper is to illustrate the use of the capacitor bank as a tool for basic experimental investigations and to determine the rapid phase-change kinetics of titanium. The capacitor provides a number of unique properties: 1) rapid heating rates in the order of l09oC per sec can be obtained; heating rates as slow as l04oC per sec are available by merely adding a given amount of inductance to the circuit; 2) the energy input can be precisely determined and can be varied from several joules to millions of joules, depending on the bank capacitance and voltage; 3) the specimen can be heated uniformly through the thickness and length or non-uniformly, as desired; 4) the apparatus is simple and inexpensive and can be easily altered; 5) the form of the specimen can be wires, sheets, foils, rods, and cylinders; 6) there is great precision in the timing of events; 7) this technique may be readily used in conjunction with rapid cooling.

Jan 1, 1965

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970

By R. I. Jaffee, F. C. Holden, H. R. Ogden

Alpha solutes increase the strengths of Ti-Mn alloys through solid-solution strengthening. The substitutional a addition, aluminum, decreases, and the interstitial solutes, carbon and nitrogen, increase the rate of nucleation and growth of a from ß. The best combinations of properties of a-ß alloys are obtained when there is a sufficient quantity of a phase in the structure to dissolve the a solutes. OF the many different titanium-base alloy systems, the predominant alloy type is the a-ß alloy. The properties of the a-ß alloys are dependent on solid-solution strengthening and heat-treatment effects involving the a-ß ratio and transformation reactions. Another variable which influences the mechanical properties of a-ß alloys is the a-stabilizer content of the alloy. An a solute may be present as an intentional addition, such as aluminum, or as an impurity element, such as carbon, oxygen, or nitrogen. It is known that these a stabilizers, when added to titanium, form single-phase alloys which are not heat treatable but which obtain their strength from solid-solution strengthening. Thus, it would be expected that a additions to a-ß alloys would increase the strength of the alloys by solid-solution strengthening of the a phase. In addition, they would affect the transformation kinetics of the ß-to-a reactions and other processes based on the instability of the ß phase. The effects of heat treatment and structure on the mechanical properties of Ti-Mn alloys have been shown in a previous paper.6 This system offers a good base to demonstrate the effects of typical a solutes on the properties of a-ß alloys. The three a solutes described in this work are aluminum, representative of a substitutional a solute, nitrogen, representative of an interstitial a solute, and carbon, representative of an interstitial compound-forming element. The effects of heat treatment and microstructure on the properties of a alloys containing these three elements are described in concurrent publications. Some of these data are used for base-line points in several of the curves used for illustration herein. Experimental Procedures Iodide titanium was used as the base for all of the alloys studied in this work. The alloys were prepared as ½ lb ingots by double arc melting in an argon atmosphere. The ingots were forged to ¾ in. rounds, vacuum annealed for 6 hr at 900°C at a pressure of 10 ' to 10-5 mm of Hg to remove hydrogen, and hot swaged to 1/4 in. diam rod. After me- chanical descaling, test specimens were prepared for heat treatment. The alloys used in this study together with the fabrication temperatures are given in Table I. Heat treatments were done in argon. For the most part, the specimens were sealed in Vyeor capsules under a partial pressure of argon. Quenching was accomplished by breaking the capsule under water. Other cooling methods used included oil quench, argon cool (simulated air cool in an argon atmosphere), and furnace cool. The times for the various heat-treating temperatures are given in Table 11. The tests performed on the alloys consisted of tensile tests on ? in. diam specimens, hardness tests, and microimpact tests. Specimen sizes have been adequately described in a previous publication.' The micrographs presented in this paper were taken from specimens cut from the shoulders of broken tensile specimens. Final polishing was done with Linde B on a slow-speed wheel, and the specimens were etched with a 1½ HF — 3½ HNO, solution. Ti-N-Mn Alloys The transformation diagram and microstructures of the Ti-0.1 pct N-Mn alloys used in this investigation are given in Fig. 1. The effect of small nitrogen additions on the binary Ti-Mn diagram is to raise the ß-transus temperature with little effect on the a solubility of manganese. Also, as has been noted previously,' high manganese-content alloys containing nitrogen, when quenched from temperatures high in the ß field, contain a subgrain boundary phase which appears to be nitrogen-rich a. Marten-site is formed when alloys containing less than about

Jan 1, 1956

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By Harry Gard Knox, F. R. Harris

This paper covers some of the problems presented to the oil industry in the drilling of oil wells in the open waters of the Gulf of Mexico. The hazards, delays and relative costs of offshore drilling are reviewed and various forms of drilling platforms discussed. The requirements of the offshore drilling rig are summarized together with the principal items affecting the cost of construction. Sea waves and their size and characteristics as affecting offshore platforms are reviewed. Drilling platforms are classified as fixed, or fixed and floating. Fixed platforms of the conventional cofferdam and pile-supported type are discussed together with their good points and their limitations. The desirability is pointed out of eliminating as much offshore work as possible where operations are subjected to constant and expensive delay and substituting therefor the prefabrication of structures ashore or in sheltered waters. Marked economy will come with the standardization of offshore rigs aid special means of transporting them to the site. Several types of structure which are partly pile-supported and partly buoyancy-supported are discussed and their possibilities of future usefulness commented upon. General Considerations The predominant attribute of offshore drilling equipment is that it must be equal to the job in hand. We therefore give first thought to the matter of adequacy. In view of the probable depth of drilling, the investment involved and the per diem labor costs, it is assumed heavy modern drilling equipment will be employed. In order to usc such equipment efficiently, the working deck must be ample in size and strength and supported so as to be relatively free from motion and from green seas even in heavy storms. These requirements necessitate a high and rigid land-based support for the drilling rig and machinery with plenty of space for supplies, such as pipe, mud, water and fuel, with reserves for days when transportation from shore is impracticable. In offshore rigs the crew will be housed onboard in comfortable quarters, probably air conditioned and equipped with a galley and refrigerated food storage. An important consideration will be the ability to transfer stores and crew to and from the rig in all but the heaviest weather and the platforms must be protected from the impact of supply vessels when alongside. It will be essential to maintain continuous communication with shore by radio or cable, not forgetting the possibility of a helicopter landing space for the transfer of crew and light stores as well as a means of general communication. Whatever structure is constructed must be secure from storms of hurricane force and a safe place for the operating crew to work. If the well comes in, the drilling rig will presumably be removed and a small but rugged pile-supported platform will remain to carry the Christmas tree with safe working space around it. It will be protected from damage on all sides by buffer piles or dolphins. It is assumed that the flowing oil will be piped to storage tanks in the vicinity of the well. An individual tank for each well or a

Jan 1, 1949

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl' who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By A. G. Buyers, J. Chilton, W. E. McKee

STUDIES in the high-temperature separations chemistry of thorium-uranium fuels are complicated by the corrosive nature of these molten metal systems at 1700°C. Separations research pointed toward the removal of fission products from irradiated alloys has included a frozen salt-bed technique which minimizes container reaction with molten metal. The procedure consists of high-frequency induction melting of the metal sample which is supported by a vertical column of unmelted salt. The molten alloy melts its immediate salt environment and as it slowly falls down through the column, many of the fission-product poisons are transferred into the fused salt environment. The molten salt-metal zone is encompassed at all times by unmelted salt, preventing container contact. EXPERIMENTAL Experimental methods were separated into three parts: salt-bed preparation, melting, and analytical evaluation. A) Bed Preparation—The procedure for casting calcium-fluoride briquettes was to compress the powdered salt at 5,000 to 10,000 psi and place this compact in a graphite crucible. This assembly was inserted into a vacuum system and surrounded by an alumina crucible as well as molybdenum, tantalum, or stainless-steel foil thermal-radiation shields. The pressure was reduced and the crucible heated under vacuum to about 800°C with the fore pump operating. Argon was then admitted to about 0.8 atm and heating continued until the CaF2 had melted 5 min at the melting point seemed satisfactory). Apparatus used included a 1-in. graphite crucible with 1/8-in. walls, 1-in. ID in a 2-in. induction coil, and a 6-kw Ajax high-frequency converter. B) Melting—Calcium-fluoride briquettes, 1 in. in diam and 1/2 to 1 in. thick, were prepared and vertically stacked to obtain the desired column length. An irradiated alloy sample (nut = 10") was placed on top of the salt column and the assembly was connected to the vacuum system. After evacuation of 5 to 10 , purified argon was admitted and the system flushed twice. The final argon pressure was about 0.8 atm. The sample was heated by induction at a power of about 6.5 kw. It then melted its way down through the salt and freely dropped into a small alumina crucible. The molten metal is followed during its downward course by the induction coil which is mounted upon a power-driven machine-threaded shaft. Experimental conditions used in the foregoing work

Jan 1, 1960