Search Documents

Discussion of the paper of F. C. NEWTON, presented at the New York meeting, Feb-ruary, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 473 to 477. H. 0. HOFMAN, Boston, Mass.-The results of these large-scale experiments, which were carried on at Perth Amboy, show that there are many differences between theoretical conceptions and their applications to work on a large scale. The author has given reasons why the results of bringing a desilverizing kettle to the high melting point of the zinc-silver alloy, Zn3Ag2, melting at 665° C., are not satisfactory. In all probability the alloy is dissolved in the lead; it may also be decomposed by the lead; the practical result is that this high temperature does not work. It remains now for the laboratory man to carry on systematic experiments

Jan 5, 1915

BULLETIN 177. The decline and ultimate production of oil wells with notes on the valuation of oil properties, by C. H.- Beal. 1919. 84 pp., 4pls., 80 figs. BULLETIN 179. Abstracts of current decisions on mines and mining, reported from September to December, 1918, by J. W. Thompson. 1919. 166 pp. TECHNICAL PAPER 214. Motor gasoline; properties, laboratory methods of testing, and practical specifications, by E. W. Dean. 1919. 33 pp., 2 figs. TECHNICAL PAPER 219. Combustion and flue-gas analysis, by U. S. Fuel Administration. 1919. 12 pp., 5 figs. TECHNICAL PAPER 223. Cost-keeping for small metal mines, by J. C. Pickering. 1919. 46 pp. Only a limited supply of these publications is available for free distribution. Publications should be ordered by number and title. Applications should be addressed to the Director of the Bureau of Mines, Washington, D. C.

Jan 7, 1919

By H. H. Hausner, H. S. Kalish

M. Hansen—This paper certainly is an interesting study. Although I have not had too much experience in the powder metallurgical methods of studying phase equilibria, I would like to say the following concerning the interpretations of the results obtained: 1. The existence of a zirconium-rich eutectic having a melting point close to 950°C and containing approximately 5 pct beryllium is well established. 2. Undoubtedly sintering of the original compacts (i.e., without repressing and resintering at 1350°C) resulted in a condition being far from equilibrium, even in the low-melting point zircon-rich region where undissolved zirconium particles have been observed. This means that only partial reaction between the component powders has taken place. 3. In preparing and handling powder mixtures for pressing and sintering, we have found that with powders differing considerably in density, and also in particle size, separation in layers of different composition may occur. This means that a concentration gradient would exist within such samples. This phenomenon may, at least to some extent, account for the difference in microstructure of the top and bottom regions of some of the sintered samples. If this is the case, density figures for some of the nominal compositions would not represent actual densities of those mixtures. 4. Fig. 1 shows that the low densities of mixtures with 40 and 60 pct beryllium sintered at 1350°C are changed to much higher densities if the products sintered at 1100°C are repressed and resintered at 1350°C, whereby an approach toward equilibrium takes place. This would mean that the low density and growth in volume is due to nonequilibrium conditions. If this is true, would it be justified, then, to conclude that "the remarkable growth of the alloys in the vicinity of 40 to 60 pct Be indicates the formation of a high-melting point phase, probably accompanied by a considerable change in volume due to a large alteration of the crystal structure from that of the original compounds"? If some compound formation has taken place already during the first sintering at 950" to 1350°C, more compound would be formed by repressing and re-sintering of the 1100" samples. This treatment, however, results in higher, rather than lower, densities. In general, the density-composition curve of alloy systems containing one or more intermediate phases is characterized by a more or less defined contraction (decrease in specific volume, increase in density) over the "theoretical" density. Does not discrepancy exist between the two statements that "growth of the alloy indicates the formation of a high-melting phase . . ." and "even at 1350°C, no indications of sintering have been observed"? 5. I am not sure that the explanation given for the fact that fig. 4 did not reveal as much eutectic as the top portions of the mixture with 2 pct Be, is correct. The density of the melt containing only 5 pct Be or even perhaps less, is not too much different from that of the nominal composition. The reason might be also that there was already some separation of the components in the pressed compact. 6. I do not understand why the microstructure of the bottom regions of the compact with 5 pct Be (fig. 6) is so different from that of the top regions (fig. 5). The compact was melted on sintering at 1100°C. Its composition lies close to the eutectic point. There should be at least some lamellar structure in the bottom regions too; otherwise, the composition of top and bottom must have been very different after sintering, because the eutectic is said to extend as far as the composition ZrBe2. In case the white and gray areas of fig. 6 are both gamma, and the black areas undissolved zirconium, this composition would be close to the phase coexisting with zirconium, that is, ZrBe2, according to the hypothetical diagram, or a compound richer in zirconium. 7. Figs. 9 and 10 are not mentioned in the text. 8. The great difference in microstructure of the composition 20 pct Be of figs. 8 and 14 on one side and fig. 15 on the other side proves that sintering at 950" and 1100°C results only in partial reaction of the powers. 9. The mixture with 60 pct Be (fig. 19) seems to consist of two phases, rather than one phase, one interspersed in a matrix of another. 10. The statement that the eta phase "may be an intermetallic compound or the product of a peritectic or monotectic reaction" seems to be misleading, because the product of a peritectic or monotectic reaction in this region of the system must be an intermetallic compound. 11. If there is some solid solubility of Be in alpha and beta-Zr, it would be expected to be higher in beta-Zr (b.c.c.) than in alpha-Zr (h.c.p.). The temperature of the polymorphic transformation of zirconium then would be lowered, rather than increased. In accordance with this, Battelle has found that the transformation point of titanium is decreased by beryllium. 12. In case the phases present in alloys with 80, 90, and 95 pct Be are identical (which appears to be correct), it is striking that the relative amounts of both phases (eta and beryllium) are not too different within this wide range of composition. With 60 to 65 pct Be

Jan 1, 1951

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relation- ships proposed by Rittinger,2 Kick,3 and Bond.4 That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes6 developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill.

Jan 12, 1959

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors' Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625' F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors' Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors' Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors' Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors' reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By H. H. Hausner, O. V. Roman, F. V. Lenel, G. S. Ansell

The radial shrinkage during sintering of cylindrical compacts and loose aggregates of copper powder was measured. It was found to be nonuni-form from top to bottom of the samples and to depend upon the method of supporting them. The non-uniformity is due to the effect of gravity forces during sintering. Since gravity has an effect in sintering without externally applied stresses, no sharp dividing line can be drawn between conventional sintering and hot pressing. RECENT investigations of the sintering behavior of compacts1 and of loose powder aggregates2 have indicated that forces, other than those arising from surface tension effects, may play a role in shrinkage. In compacts it was shown that residual stresses from the pressing operation influence shrinkage behavior. In loose powder aggregates gravity forces due to the weight of the powder affect the ratio of shrinkage in the vertical and the horizontal direction. The main effort in the work reported here was to show that gravity plays a role also in the sintering of compacts. A few additional experiments were made confirming the effect of gravity in the sintering of loose powder aggregates. EXPERIMENTAL PROCEDURE Compacts and loose powder aggregates were prepared from irregularly shaped, electrolytic copper powder. Prior to use the powders were reduced 30 min at 400°C in dry hydrogen to remove surface oxides. Then the -325 mesh size fraction was separated from the -100 + 325 mesh fraction. The compacts were pressed at a pressure of 10,000 psi from 50 g of powder in a hardened steel die, 1 in. in diam. The height of the compacts was 0.725 i 0.005 in. An effort was made to get as uniform a green density distribution in the compacts as possible. The walls of the die were lubricated with a suspension of 3 pct of zinc stearate in acetone and the compacts were pressed using double action by first pressing the powder at 1200 psi with the die barrel supported, then removing the sup- ports and pressing to final pressure of 10,000 psi with the die barrel floating. The pressure was maintained for 10 sec. The compacts were sintered at a temperature of 925°C, generally for 1 hr. In order to maintain uniform temperature they were sintered in boats made from cylindrical copper blocks. The blocks were 2 in. in diam, either 2 or 2 1/2 in. long and, split to form the body of the boat and a lid. The body of the boat contained a cavity 1 3/8 in. wide, 1 in. deep and either 2 1/8 or 1 3/8 in. long. The longer cavity accomodated two samples, the shorter one only one sample. The uniformity of temperature distribution within the boats was checked with thermocouples welded to the top and bottom of the samples. The maximum variation between top and bottom temperatures was i 1/2°C. The actual sintering temperature was held constant within ±2°C. In order to determine the effect of gravity forces, i.e., the weight of the compacts, upon shrinkage, they were supported in the following ways during sintering: a) Full Bottom Support. The compacts rested either on a flat alundum disk or on alundum powders. b) Partial Bottom Support. The compacts rested on a graphite cylinder, 0.3 in. in diam which formed a projection on a larger graphite disk. It is difficult to balance the compact on the small projection. To avoid having the compact tip, a small hole was drilled through the compact and through the graphite disk and its projection. The graphite disk was then suspended from the lid of the boat by a thin iron wire which passed through the holes in the disk and the compact. c) Top Support, first type. A hole 3/32 in. in diam was drilled diametrically through the green compact 3/16 in. from the top of the compact. The compact was sintered suspended from an alundum rod (thermocouple protection sleeve) inserted into the hole. d) Top Support, second type. A hole was drilled axially through the center of the compact. The upper part of the hole from the top surface of the compact one fourth of the way down was 1/16 in. in diam; the lower part of the hole from the bottom surface three fourth of the way up was 3/32 in. in diam. The compact was suspended from the lid of the boat by an iron wire passing through the upper part of the hole and then tied into a knot. The loose powder aggregates were made by filling l in. deep, l in. diam cylindrical graphite molds with -325 mesh powder. To achieve uniform density in all the loose powder aggregates, the powders were settled in the molds by placing the

Jan 1, 1963

By F. E. Crane, H. A. Kendall, G. H. F. Gardner

Two effects of a difference in density may be observed in miscible displacement. As the difference is increased from zero there is first a change in mode from multiple fingers to a single finger. A further increase results in a more rapid growth of the single finger. Miscible displacement with multiple fingers has been discussed by Blackwell, et al, whereas miscible displacement with a single finger has been discussed by Craig, et al. In the present paper experiments are described which bridge the gap between these extreme cases. INTRODUCTION Craig, et al,1 investigated the effect of gravity on frontal displacements for circumstances in which the gravity forces were significant. Blackwell, et a1,2 dealt with the other extreme in which gravity forces were negligible. The considerable difference between their results is illustrated in Fig. 1 where the breakthrough recoveries are plotted against the mobility ratio. The experiments described in the present paper were conducted to examine how the transition from the one extreme case to the other occurs when the gravity forces are gradually reduced. The transition is well illustrated by the production history after breakthrough. Fig. 2 shows how the number of pore volumes which must be injected at a constant rate to displace 98 per cent of the original fluid depends on the gravity force. For each mobility ratio there is a transition range, and a very significant change in the number of pore volumes occurs when this range is traversed. This range of the gravity force is physically linked with the formation of viscous fingers. A single finger is predominant for larger gravity forces; a multiplicity of fingers is formed for smaller gravity forces. Improved recovery and the occurrence of multiple fingers is concomitant with a large increase in the amount by which the fluids are mixed within the porous medium. The transition range depends on all the dimension-less groups which characterize the problem; but this dependence has not been exhaustively studied as yet and only fragmentary results are discussed in this paper.

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By William A. Mitchell

AN X-ray diffraction pattern for "calcined cold precipitated ferric oxide" is reproduced diagrammatically along with data for other iron oxides by R. C. Mackenzie.1 This pattern, which shows spacings higher than those for any other form of iron oxide, was obtained from material prepared and photographed at several different times over a period of weeks, but later attempts to reproduce the results were unsuccessful the pattern of hematite being obtained every time.2

Jan 9, 1953

By O. Jantti, Erkki Laurila, R. T. Hukki

INVESTIGATION of the methods of analyses for magnetite and ilmenite in the Otanmaki iron-titanium ore and respective mill products has resulted in certain improvements in the methods conventionally employed. The outcome of the investigations is summarized as follows: 1—Development of a diamond-drill core analyser for the determination of magnetic susceptibility of drill cores containing magnetic minerals. 2—Development of a magnetite-ilmenite analyser for pulverized products. 3—Development of a potentiometric method of chemical analysis for the determination of iron, vanadium, and titanium in succeeding steps from one test sample. 4—Proposal for a continuous and automatic magnetite assay method. Diamond-Drill Core Analyser The conventional method of assaying diamond-drill cores consists of splitting the cores, pulverizing them and running chemical analyses on representative samples. The physical properties of magnetic minerals, however, offer an entirely different approach to obtain similar final result by the measurement of respective magnetic susceptibilities in a properly designed instrument. This instrument is shown in Fig. 1. Essentially it consists of a magnetic unit, A, and of a meter unit, B. On top of A is a slot where a piece of diamond-drill core C is visible. The magnitude of disturbance in the original magnetic field caused by the magnetic minerals in the drill core can be observed from the microammeter. This reading is a function of the combined susceptibilities of all magnetic grains in the magnetic field. The magnetic unit is built of E-sheets of a shell transformer, as shown in Fig. 2. The primary coil and two identical secondary coils are wound around the central leg and end legs, respectively. The drill core under examination is placed into one of the air gaps as shown in Fig. 2. The number of ampere-turns of primary coil excited by 50 or 60-cycle ac give a maximum induction of about 600 gauss in the air gaps. The secondary coils are connected in series in the opposite direction. Thus their voltages compensate each other if no drill core exists in the air gap or if the susceptibility of the drill core is equal to zero. As soon as the susceptibility becomes greater than zero, the balance of the magnetic circuit is disturbed, resulting in increased voltage in the terminals of coil 1 and in a respective decrease of voltage in the terminals of coil 2. The voltage difference thus produced is a function of the effective susceptibility of the drill core. If the magnetic grains in the drill core are unevenly distributed, the voltage difference varies as the core is rotated around its own axis. The voltage difference is measured with a Bren-tan0 tube voltmeter. If extreme sensitiveness is desired, the established symmetry of the magnetic circuit does not allow reduction of the 0-voltage difference far enough. Therefore a compensatory voltage of a correct phase taken from the terminals

Jan 1, 1952

By Oren C. Baptist, Eliot J. White

Samples of four reservoir sands having different degrees of water sensitivity were subjected to several laboratory tests to determine differences in capillary behavior attributable to clay-mineral effects. The degree of water sensitivity was estimated by the difference between gas and water permeability. Unsaturated pore volumes determined with mercury injection were comparable to irreducible water saturations determined with the semipermeable bar-rier method only for the non-sensitive sands that contained small amounts of non-swelling clay minerals. Irreducible saturations were independent of salinity of the water, which suggests that most residual water is adsorbed 0.7 a film over solid surfaces and that internal retention by clay minerals is relatively insignificant. The water-sensitive sands imbibed water to higher saturations than did non-sensitive sands, and this result is believed to be a combination of the effects of clay minerals and preferential wettability; however, the relative importance of each of these effects is riot determinable. Thus it is concluded that the semipermeable barrier method is the best of the laborafory methods used for estimating formntion water .saturations in the sands studied. INTRODUCTION This investigation is a continuation of studies of the role of clay minerals in petroleum production in the Rocky Mountain area. Previous work has shown large differences in gas and water permeability in numerous reservoir sands; these water-sensitivity effects observed in the laboratory have been correlated with well behavior in the field, and the degree of water sensitivity imparted to reservoirs by the various clay minerals has been determined.'.' The effect of interstitial clay minerals on formation water3 saturations is not so well known. It has been reported that formation water saturations probably are higher in clayey than clean sands,' but this effect has not been evaluated in the laboratory, and the relative effect of the various types of clay minerals on formation water saturation has not been determined. The clay-mineral groups of most importance to this study and to petroleum production in general are kaolinite, illite, and montmorillonite. The minute layers of montmorillonite are loosely bound to one another so that water enters between them, causing great expansion of the particles. Kaolinite and illite do not exhibit interlayer hydration, but they do immobilize considerable amounts of water owing to their large surface areas, which are of the order of 15 to 97 m2/gm of clay.5 The four Wyoming sands used in this study were selected to represent a wide range of water sensitivities. These sands, with the number of wells and fields from which the samples were obtained, are: Second Frontier, five wells in two fields; Newcastle, six wells in one field; Tensleep, two wells in two fields; and Lower Muddy, five wells in one field. EXPERIMENTAL METHODS AND PROCEDURES Water-displacement data were obtained by the semipermeable barrier method," using both fresh water and brines having either 16,500 ppm sodium chloride or calcium chloride. A displacement pressure of 35 psi was found to be sufficient to obtain the practical irreducible water or brine saturation (IWS, IBS) in most samples. Mercury-injection data were ob-tained with equipment and pro-cedures similar to those described by Purcell.7 Exceedingly high pressures are required to attain complete mercury saturation by this method; however, since saturations in most samples change very little with large pressure increases above 1,000 psia, the maximum pressure used was 1,400 psia. To facilitate comparison of mercury-injection and water-displacement results, it is convenient to express mercury-injection data in terms of unsaturated pore volume. The abbreviation, (100 - SHg)min, is used to denote the pore volume unsaturated by mercury at 1,400 psia injection pressure. Gas permeabilities, ki, were deter-mined by the method proposed by Klinkenberg.8 Methods of determining types and amounts of clay minerals by X-ray diffraction analyses, as well as methods of determining water permeability, have been described previously.' The imbibition characteristics of

Jan 1, 1958

By G. F. Jenkins

The word asbestos is a broad term that has been accepted and applied to a number of fibrous mineral silicates found in nature. They are incombustible and can be separated by mechanical means into fibers of various lengths and thicknesses, but differ in chemical composition and other properties. It is generally recognized that there are six varieties of asbestos; the finely fibrous form of serpentine known as chrysotile, and five minerals of the amphibole group, i.e., amosite (not fully recognized as a mineral species name but accepted in asbestos terminology), anthophyllite, crocidolite, tremolite and actinolite. (Figs 1-4.) Physical and Other Properties The structures of asbestos fibers have been studied intensely in recent years. X-ray diffraction patterns 1 to 15 have been used as a means of identification and classification. The amphibole group structures have been fairly well established while the serpentine group has been the subject of many investigations during the past six years. Low-angle X-ray scattering techniques5 have shown that the chrysotile fibrils are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 180Å* units to 300Å units, while the amphibole fibers are many times larger in cross section. The electron micrographs of chrysotile asbestos (Figs 1-4) have also indicated that the fibrils might be in the form of a hollow tube. This point has been the subject of considerable controversy by a number of investigators.7 to 16 Density measurements17 made on a sample of high quality Arizona fiber did not indicate that the fiber had a hollow tube structure; however, the so-called "sheet structure" of the fibril could be distorted in such a way that it gives the appearance of a hollow tube in the electron microscope. It is of interest to quote one investigator, F. L. Pundsack,17 in this connection: Although the empirical composition of chrysotile is 3MgO.2SiO2.2H20, the true unit cell[#] composition is best represented as Mg12(OH)16Si8O20. This cell has dimensions of a= 5.3Å, b = 9.2 Å, and c = 14.6 Å where the "a" direction is the fiber axis. The calculated density of this unit is 2.56 g/cc, a value in close agreement with experimentally determined density values for chrysotile. The exact manner in which the unit cells of asbestos are stacked together to build up a single fiber of chrysotile is not known, but from various

Jan 1, 1960

By R. J. Evans

THE Combined Metals Reduction Co.'s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. PIOCHE ORE The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericite and graphite. The ore is an exceptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and are extremely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent. minus 150 mesh shows pyrite, sphalerite and galena still attached. EARLY ATTEMPTS AT ORE DRESSING Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore since 1913; in fact, a total of 35 commercial and plant laboratories experimented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effect a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-that is, about minus 200 mesh-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considered practicable at this time.

Jan 1, 1928

Jan 1, 1880

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces The awakening of interest in this subject is due to the applicability of the electron diffraction technique to the study of surfaces The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory This interpretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state In the present paper new, and hitherto unpublished, electron diffraction effects from polished zinc are described These observations indicate that the polished surface of zinc is crystalline PUBLISHED WORK Many papers2-10 have interpreted the electron diffraction evidence as proof of the Beilby amorphous theory All investigators agree that highly polished metals give rise to two diffuse diffraction haloes, similar to those obtained by the diffraction of X-rays in liquids and vitreous solids It is this similarity that leads to the amorphous-layer interpretation of polished metals Strangely, the interatomic distances calculated from these haloes are very similar for the various metals investigated, in spite of a rather wide range of such distances in the crystalline and liquid states The calculated atomic sizes are, furthermore, smaller than are experienced in the normal states of the metals In spite of these anomalies, the amorphous-layer interpretation has been adhered to by many One investigator, S Dobmski,11 differs from the others in his experimental results By polishing under benzene in order to avoid the possibility of oxidation, Dobinski obtains diffuse haloes of [radire] different from those previously obtained He thus obtains a more rational quantitative correlation of-the diffuse haloes with the amorphous-layer theory

Jan 1, 1938

THOMAS T. READ, Palmerton, Pa. (communication to the Secretary*). -It is much to he regretted that in presenting a further discussion of these deposits, first described by myself' and later discussed by C. M. Weld,2 Mr. Wang bas not made a more complete presentation of the evidence on which he bases his conclusions as to their origin. Mr. Weld said in his paper that his visit was confined to a few hours, that he saw only one of the several exposures, and that he took away no samples for further study. My own visit was brief, and for another purpose than the study of the geological features of 'the deposits, so the fact that Mr. Weld described as a hornblende-granite the rock which I described as a "dark gray syenitic rock," and which Mr. Wang identifies as a hornblende-syenite, seems of no great importance, since this rock is generally decomposed along the contact, presumably the only place in which Mr. Weld observed it. Later in the same paper (p. 31), Mr. Weld says that his opinion is that the magnetite of the deposits is primary, but Mr. Wang makes no mention of this in stating his own conclusion to the same effect. When Mr. Weld's paper appeared, I did not discuss it, because, although I considered the evidence- that he brought forward to support his belief that the magnetite is primary too slender to support the hypothesis, my own evidence to the contrary was equally tenuous. .The opportunities for observation and study open to Mr. Wang must have provided him with

Jan 6, 1917

By D. S. Hutton, W. C. Leslie

S. Floreen (1nteumtio)lal Nickel Co.)— One fairly simple way to differentiate between embrittlement due to surface microcracks or due to a dislocation barrier effect might be to load a brittle rock salt crystal in tension to some stress just below the fracture stress and then immerse the loaded crystal in water. If a surface film is retarding plastic flow then one should observe some plastic deformation of the rock salt as

Jan 1, 1962

By R. C. Thompson

The lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 450-ton operation. General Description The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1949