Search Documents

By F. C. Blake

The apparatus which I shall describe in this paper has been in ase for some time at the laboratory of the Pennsylvania Lead Company's works, and has been found to give good results, and to be simple and convenient. Steam Bath.—This steam bath is shown by Figs. 1, 2,3 and 4. It is made of sheet copper, about one-twelfth of an inch thick, the joints being brazed, and is used for heating the bottles in which the silver samples are dissolved,-previous to the fineness determina-

Jan 1, 1882

By W. D. Forgeng, R. E. Grace

The rate of copper corrosion in liquid lead was studied as a function of flow rate and temperature in a closed isothermal loop system between 350" and 500°C. Kinetic data were interpreted with the Nernst-Brunner equation and the Chilton-Colbum mass transfer analogy to heat transfer. Over the range of temperatures and flow rates employed the solution rate constant varied from 2 x 10-3 to 20 x 10-3 cm per sec. The rate constant was found to vary with the 0.76 power of the Reynolds number in the range 7500 < Re < 40,000. The results of this investigation indicate that the Cu-Pb corrosion process is controlled largely by diffusion across a boundary layer. particularly at the higher temperatures. The effective boundary layer for diffusion is found to be approximately three to four times smaller than the momentum boundary layer. CORROSION by liquid metals has long been a problem during melting, static containment, and casting. Recently, considerable emphasis has been placed on the understanding of liquid metal corrosion mechanisms in an effort to prevent mass transfer and eventual failure in liquid metal heat exchangers and in liquid-metal-fueled nuclear reactors. The present investigation was conducted to determine the relationships which exist between corrosion kinetics and hydrodynamic conditions in an isothermal loop containing a simple liquid metal-solid metal corrosion system. The Cu-Pb system was chosen for its simplicity and ease in handling. Previous isothermal Cu-Pb corrosion studies1-3 have been conducted in both static and dynamic systems but not under conditions which allow easy "scale-up" to engineering systems, such as liquid metal heat exchangers. On the other hand, most liquid metal loops which have been used to evaluate mass transfer rates4 have been driven with temperature gradients under conditions of natural convection and unknown flow rates. The primary contributions of this research are twofold: 1) to evaluate the design of a simple isothermal loop corrosion system and 2) to investigate liquid metal corrosion behavior under well-defined hydrodynamic conditions. MATERIALS AND EXPERIMENTAL WORK The apparatus used to measure the Cu-Pb corrosion rates is shown schematically in Fig. 1. The loop system consisted of 1) a reservoir made of Type 316 stainless steel containing a centrifugal pump and 2) stainless-steel tubing containing a removable copper test section. The copper test section was OFHC hard-drawn tubing, 11.0 0.05 cm in length and 0.775 ±0.005 cm ID. A Type 316 stainless-steel venturi meter* was inserted in place of the copper test sec- tion in order to determine the lead velocity as a function of pump speed at each temperature. The Cu-Pb system was chosen for this study because the solubility of copper in liquid lead is large enough to measure accurately but small enough that the diameter of the copper tubing was not changed significantly by corrosion. There are no intermediate phases formed in the system, and the solid solubility of lead in copper is vanishingly small so that back-diffusion cannot occur. Molten lead (corroding grade; 99.94+ pct Pb, 0.0015 max pct Cu) was charged from an auxiliary melting furnace into the system under an argon cover to minimize oxidation. The lead was then maintained at constant temperature by a stirred molten salt bath in which the loop was immersed to a depth just above the lead level in the reservoir, Fig. 1. The total volume of lead in the system was 320 2 cu cm.

Jan 1, 1969

By AIME AIME

EVEN though most of the program of the joint meeting at Easton, Pa., on Oct. 30 to Nov. 1. was devoted to the interests of combustion engineers rather than to coal-mining engineers, nevertheless the A.I.M.E. Coal Division was well represented, with 83, or close to one third of those in attendance giving this as their affiliation. The fuels division of the American Society of Mechanical Engineers had 108 representatives, and an equal number reported no society affiliation. Added to the men&apos;s total registration was that of some twenty ladies so the total attendance was in the neighborhood of 325, exceeding that of the last two joint meetings, at Birmingham and Columbus, and equaling the 1938 crowd at Chicago.

Jan 1, 1941

By P. R. Sheorey

I read this interesting paper on pillar strength in some detail because this is also my area of interest. It has long been the desire of mining rock mechanicians to predict pillar strength from laboratory compression tests. Considerable literature is available on compression strength of rocks and coal but many of these experiments were conducted not for pillar design but for rock behavior. I have a few comments on the author&apos;s approach to pillar design, especially equation (33). Two important factors, which the author seems to have excluded, can be added to the right side of equation (2): time-dependence of strength and the influence of mine environment on strength (moisture and weathering.) The author has taken considerable pains to analyze a large amount of testing data in [Table 1], yielding the various exponents ci of equation (2) (or the subsequent equations derived from it.) He has, however, not shown by means of a worked out example how these values of [Table 1] could be applied to a practical pillar design situation. It would have been interesting to compare predicted pillar size using equation (33) with an actual case. Alternatively, equation (33) could have been used to explain the failure of a pillar, if such a case history were available. Consider we have a large number of case histories of stable and collapsed pillars in a seam and we conduct a large number of tests in a laboratory press. The exponents [ci] can then be determined for actual pillars as well as for test specimens. Thus, equation (2) will read [ ] Since laboratory testing conditions (e.g., between steel platens) are different from the conditions on pillars, the exponents [ci] in

Jan 1, 1983

By J. F. Myers, S. D. Michaelson, F. C. Bond

This work was undertaken with the object of collecting plant data on rod milling, making laboratory tests on representative samples of the various ores, and arriving at a basis for comparing the relative efficiencies of different mills operating on widely different materials and under varying conditions. These efficiencies consider only power consumption and do not include the other elements of operating costs. The over-all economic efficiency may be quite different from the consumption efficiencies with which this paper is concerned. It is hoped that these collected data will be of value in indicating the most favorable conditions of rod-mill operation. Operating-plant data on 14 different installations from II plants throughout the United States and Canada were collected, and laboratory tests were made on samples of these ores. The plant rod mills were all operated wet, and either in open circuit or with circulating loads so small as to be negligible. Data were obtained on one roll-crushing operation at the Utah Copper Co., for comparison. The rolls were operated wet in closed circuit with 10-mesh vibrating screens, and with a high circulating load averaging about 600 pct. This particular roll operation can be considered as a model of efficiency. The collected plant data are necessarily incomplete in some instances. Each ore was assigned a code number, and the name and location corresponding to the code number are listed in Table I when permitted. The power data in every instance refer to motor input. Net power was reported by the operator for samples 1-30 and 1-45, and this was increased by 20 pct to compensate for motor losses and power factor. The plant rod-mill data are listed in Tables 2 and 3. In Table 2 the speeds are calculated on the basis of partly worn rod-mill liners 2 in. thick. Where D

Jan 1, 1949

By C. A. Doh, R. Q. Fields, M. Lebourg

A formation tester run on logging cable is now available to the oil industry. It offers a method of safely and rapidly testing possible producing formations in uncased holes. These tests can be made up the hole after running the electric log. Reservoir pressure data is continuously recorded at the surface as the fluid sample is extracted. The tester may be assembled with a reservoir of 1-, 2.75-, or 5.5-gal capacity. A retaining pad on the body of the tool is expanded against the wall of the hole at the exact depth desired; this depth is determined by electrical log control. Two bullets are then fired through the center of the retaining pad which create a connection between the formation and a flow line to the sample chamber. When the chamber is filled, a valve is closed and the fluid sample sealed at maximum pressure. The tool is retracted to minimum diameter and brought out of the hole. Electrical circuits permit a complete recording at the surface of the mechanical operations of the tool as well as the formation pressure build-up and the hydrostatic mud pressure. The tool was introduced commercially during the latter part of 1955 in the Gulf Coasts of Louisiana and Texas. Over 1,000 operations have been made to date (Sept. 1, 1956); 50 per cent of which resulted in successful tests. Failures have been due mostly to ineffective sealing in unconsolidated sands. One major company had 41 successful tests out of 80 attempts with 23 ineffective pad seals. Results for this company were very gratifying as to pinpointing gas-oil ratios, indicating productive permeabilities and aiding in determination of fluid content where electrical log and side-wall coring information were inconclusive. Eight typical pressure curves are discussed (including misruns). Six types of fluid recoveries are interpreted. Eight actual field examples of electric logs, showing the problems solved by the formation tester, are illustrated. The present applications of the tool are discussed: 1. Determination of productive fluid—varticularlv differentiating between gas and oil. 2. Determination of reservoir pressure as an aid to: (a) safety in completion technique, (b) reduction in drilling costs, and (c) reservoir analysis. 3. Determination of minimum gas-oil ratios. 4. Location of gas-oil or oil-water contacts. 5. Recovery of samples for examination and analysis: oil (gravity); gas (hydrocarbon content); water (salinity). Additional applications envisioned for the future are also given: (I) subsurface exploration based on accurate pressure, (2) recovery of fluid samples from the undisturbed reservoir for PVT work, and (3) possible quantitative study of permeabilities or productivity index. Running the formation tester requires no special pre-cautionary measures. Because full hydrostatic mud pressure is maintained at all times, well depth is no problem. Thus, the method allows safe, economical testing in wells which heretofore could only be tested by setting casing. INTRODUCTION A new method of safely and rapidly testing possible producing formations in uncased holes is achieving considerable success. The method offers promise of further advances in reservoir study. Called the formation tester, the new instrument is unique in that it operates on logging cable. It thus offers all the advantages of wire-line operations and becomes an important adjunct to present logging and side-wall coring services. The tester is operated against the wall of the hole at any depth desired. Zones to be tested are usually determined by a study of the electrical and the micro-caliper surveys. Reservoir data, as well as the operating cycle of the tool in the hole, are continuously recorded at the surface during the operation. The tester, as it was originally designed, was capable of recovering a 1-gal sample of reservoir fluid per trip in the hole. Tools with reservoirs of 2.75- and 5.5-gal capacity are now available. The 5.5-gal reservoir is equipped with a segregating system, set before going in the hole, so that the last portion of the recovery (usually 1 gal) is automatically separated from the first portion. This makes it possible

Jan 1, 1958

By W. Mitchell, B. H. Bergstorm, C. L. Sollenberger

A unique compression testing machine was constructed to load individual 1/8 to I-in. spheres of glass, etc., at rates from 100 to 100,000 lb per min. During loading the applied load was continuously plotted us the deformation of the sphere-platen system. The load-deformation curve conforms to the theory of elasticity. The spheres were surrounded by steel retaining rings or by gelatin (to prevent secondary fracture). The product size modulus was determined from screen analyses. The data shows: 1) Energy input per unit mass is inversely proportional to the product size modulus (or directly proportional to the surface area per unit mass). 2) Increased loading rates slightly increase the energy input per unit mass required for fracture without affecting the preceding relationship. Theory and experiments show that much of the input strain energy is transformed into kinetic energy of fragments at fracture, this being a reason efficiencies based on "surface energies" are exceedingly small. This large kinetic energy component is usually dissipated as heat but may be partially reclaimed because impact of fragments against the surface of steel retaining rings causes additional comminution. There are currently several theories of crushing, all of which can be derived from the general energy equation of Gillilandl as was pointed out by Mitchellet al in 1954&apos;and more recently by Rose and Sullivan. If the exponent of the equation dE-x-"dx is assigned values of 2,1, or 3/2, one obtains by intergration between suitable limits, the equations of Rittinger, kick,&apos; and Bond,&apos; respectively. Other investigators prefer to let the exponent be a variable parameter. To help resolve the controversy, the Allis-Chal-mers Research Laboratories set up a series of carefully controlled experiments in which the level of energy input required to induce the comminution of a single particle by slow compression loading was very accurately measured. The energy input requirement, in conjunction with the size analysis of the fragments produced at fracture, yielded an accurate energy-product size relationship for the conditions studied. APPARATUS The experimental apparatus was designed to apply a compressive load on opposite sides of an "ideal particle." Spherical shapes were chosen, because point contact loading is typical of the mechanics of conventional crushers. The bulk of the experimental data was obtained with glass spheres because glass is a fairly homogeneous, brittle material for which the properties follow definite statistical distributions. The spheres ranged from 1/8 to 1-in. diam. The compressive load was applied to the specimen at a uniform rate by a loading mechanism (Fig. 1) which acted through a system of levers. The uniform rates, ranging from 100 to 100,000 lb per min, were obtained by metering water into a bucket suspended at the end of the secondary level. Point contact was made with the sphere through tungsten-carbide platens. This latter material is extremely hard and has a high modulus of elasticity, thereby having a minimum of distortion when loaded. The actual load on the sphere was measured independently of the lever system by a load cell, Fig. 2, which was designed so that the voltage output of the load cell would be proportional to load. The deformation of the specimen was indirectly measured by a pair of transformers which were attached to opposite edges of the upper platen. The cores of the transformers, which were attached to the lower platen, moved relative to the transformer so that the voltage output was proportional to the deformation of the sphere-platen system. The load was plotted against the deformation on an X-Y recorder. The area under the curve, as shown on Fig. 3, was proportional to the energy input of the

Jan 1, 1961

By P. H. Royster

On the Continent, ferromanganese has been produced in the blast furnace almost continuously since 1876, but little definite information concerning the practice is to be found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country, prior to 1904, but one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public..In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations; so the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Operating data were collected by the Bureau from eleven ferromangahese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P; the dimensions of seven of the furnaces are given in Table 1. The companies from whom this information was obtained, and to whom should go the credit for whatever value this information may possess, are the Bethlehem Steel CO.,

Jan 1, 1920

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;&apos; calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By Donald L. Everhart

SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the over- all job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Com- pared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits.

Jan 9, 1954

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"&apos; was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.&apos; In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

Jan 1, 1904

NEW MEMBERS The following list comprises the names of those persons who became members during the period of June 10, 1918, to July 10, 1918. ALLPORT, JAMES H., Cons. Engr Barnesboro, Pa. ANDERSON, G. E., Engr., Exploration Dept., American Smelt. & Refin. Co.,Tucson, Ariz. BAKER, HARRY A., Capt., Co. M, 53d Pioneer Infantry, Camp Wadsworth, Spartanburg, S. C. BEALL, ROBERT STEPHENS, Supt., Empire Zinc Co. (of Colorado), Canon City, Colo. BLAYLOCK, SELWYN GWILLYM, Mina & Met. Engr., Asst. Gen&apos;l Mgr., Cons. Min. & Smelt. Co. of Canada, Ltd., Trail, B. C., Canada. BOTTERILL, THOMAS CLARK, Min. Engr., Belmont Surf Inlet Mines, Ltd., Surf Inlet, B. C., Canada. BOWMAN, MAURICE Asst. Supt., New Idria Quicksilver Min. Co., Idria, San Benito Co., Cal. BROOKS, EARL W Chief En r. Inland Collieries Co. Harmarville Pa. BROWN, DEWITT W Chief Chem., Prime Western Spelter Co., Iola, Kansas BUISSON, ARTHUR Min. Engr., Dept. of Mines, Sussex St., Ottawa, Canada. BUNYAN, F. W Chem., Southern Pacific Railway Co., Sacramento, Cal. BURNETT, ARCHIBALD Supt., Swansea Lease Inc., Swansea, Ariz. BURTON, GEORGE E., Resident Geol., Empire Gas & Fuel Co., Varsity Shop Bldg., Norman, Okla.

Jan 8, 1918

By H. A. Kursell

IN pre-war days, the mining industry of Russia occupied in the industrial life of the Empire a place of ever increasing importance. The peak of produc-tion was reached in 1913 and 1914, the years of greatest prosperity, and a rapid growth of the mineral industry seemed assured, especially as regards base-metal mining. Exceptions were the gold production, for which a gradual decline was anticipated, and the platinum out-put which was expected to remain steady. A greater productivity of labor, corresponding to better working facilities was noticeable, and the economic status of the working classes was constantly improving. The tremendous strain on Russia&apos;s economic life caused by the World War did not materially alter the prospects of the mineral industry and the fundamental changes began only with the revolution in the spring of 1917. Their scope and character are illustrated by the figures in Table 1 which compare, for the parts of the Russian Empire under Soviet (R. S. F. S. R.) control, the average mineral production of 1913 and 1914 with that of 1920, 1921 and 1922, as supplied by bolshevik sources.1The latter three years in Russia&apos;s history were characterized by the firm establishment in power of the Communist party as a new ruling caste. Silver, lead, zinc, tin, nickel, tungsten, barite, etc., were either produced in negligible quantities, or not at all. However, before the revolution the development of several argentiferous lead-zinc deposits in western Siberia had reached a stage which seemed to assure an appreciable output of the white metals for the near future.

Jan 7, 1923

By Henry M. Howe

Jan 1, 1909

By K. J. Gill, P. Chiotti, J. T. Mason

Thermal, metallographic, and vapor pressure data were obtained to establish the pkase boundaries and the standard free energy, enthalpy, and entropy of formation for the compounds in the Y-Zn system. Three coinpounds with stoichiometric formulas of YZn, YZn2, and Y2Zn17 melt congruently at 1105", 1080°, and 890°C, respectively. Four compounds with stoiclziometric formulas of YZn3, YZn4, YZn5, and YZn,, undergo perztectic reactions at 905", 895", 870º, and 685ºC, respectively. Three eutec-tics exisl in this system with the .following eutectic temperatures and zinc contents in wtpct: 875ºC, 23.2 Zn; 1015ºC, 51 Zn; 865ºC, 82 Zn. The YZn, pkase undergoes an allotropic transformation. In the two phase YZn2 -YZn alloys the trans.formation gives a weak thermal arrest at 750°C, whereas in the two phase YZn2-YZn3 alloys no thermal arrest is observed and the transformation occurs over a temperature range below 750°C. At 500°C the free mzergies of formation per lnole vavy from —18,090 for YZn to —53,430 fov YZr11 and corresponding enthalpies vary from -24,050 to -92,080. The free energies and enthalpies per g atom as a function of composition show a maximum for the YZn2 phase; the 500°C values are -9580 and -13,180, vespectively. 1 HE only information found in the literature on Y-Zn alloys was the observation reported by Carlson, Schmidt. and speddingl that Y-20 wt pct Zn forms a low melting alloy. The alloy was produced by the bomb-reduction of YF3 and ZnF2 with calcium in an investigation of methods for producing yttrium metal. The solubility of yttrium in zinc has been determined by P. F. woerner2 and reported by Chiotti, Woerner, and Parry.3 In the temperature range 495" to 685°C the solubility may be represented by the relation In these equations N represents atom fraction of yttrium and T is the temperature in degrees Kelvin. The purpose of the present investigation was to establish the phase diagram for the Y-Zn system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory yttrium sponge. Arc-melted yttrium buttons contained the following impurities in parts per million: C-129, N-12, 0-307, Fe-209, Ni-126, Mg-13, Ca < 10, F-105, and Ti < 50. Some of the alloys containing 70 wt pct or more of Zn were prepared from yttrium containing 5000 ppm Ti as a major impurity. Tantalum containers were found to be suitable for all alloys studied and were used throughout the investigation. The pure metals, total weight about 30 g, were sealed in 1 in. diam tantalum crucibles by welding on preformed tantalum covers. A 1/8 in. diam tantalum tube was welded in the base of each crucible for use as a thermocouple well. Welding was done with a heli-arc in a glove box which was initially evacuated and filled with argon. The sealed crucibles were enclosed in stainless steel jackets and heated in an oscillating furnace at temperatures up to 1150°C. Homogeneous liquid alloys were obtained within a half hr at these temperatures except for alloys containing less than 20 pct zinc. The latter alloys were held at 1000º to 1100°C for 2 to 3 days in order to obtain equilibrium. After the initial equilibrations the tantalum crucibles containing the alloys were removed from the steel containers and used directly for differential thermal analyses. Further annealing heat treatments for alloys in which peritectic reactions were involved were carried out in the thermal analyses furnace. After thermal analyses the tantalum crucibles were opened and the alloys sectioned and polished for metallographic examination. In the following discussion alloys referred to as "quenched" were obtained by quenching the sealed stainless steel jacket containing the tantalum crucible and alloy in water. The differential thermal analyses apparatus used was a modified version of the one described in an earlier paper., The graphite crucible was replaced by an inconel crucible, the nickel standard and sampie container were separated by a 1/8 in. MgO plate, no getter was used, and provisions were made to

Jan 1, 1963

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18

Jan 1, 1923

By R. V. Whetsel, V. R. Garfias

Production of crude petroleum in Mexico during 1936 totaled approximately 40,309,000 bbl., showing a negligible increase over the previous year. While only four producing wells were completed in the Poza Rica area in 1936, its production increased from 9,468,000 bbl. in 1935 to 13,417,000, making it the ranking producing field in Mexico. This gain in output, however, was offset by abnormal losses due to artificial curtailment mainly the result of strikes and other disturbances in the heavy-oil district of the Northern fields, which declined 2,500,000 bbl., and in the South fields (Golden Lane), where output decreased 1,500,-000 bbl., while production in the Isthmus of Tehuantepec fields remained practically stationary. Production of natural gasoline for 1936 is estimated at 800,000 bbl., or 200,000 bbl. greater than in 1935. Crude run to stills in local refineries increased about 1,000,000 bbl., totaling 31,000,000 bbl. for 1936. Exports of crude and refined products were approximately 24,400,000 bbl., or over 2,000,000 bbl. greater than in 1935, the increase representing withdrawals from storage in Mexico. Exclusive of ships&apos; bunkers, domestic consumption increased about 1,000,000 bbl. during the year, reaching an estimated total of 15,200,000 bbl. The Mexican domestic demand for gasoline is estimated at 2,540,000 bbl. for the year, an increase of 310,000 bbl. over 1935. In all, 70 wells were completed in Mexico during 1936, as compared to 74 in 1935 and 148 in 1934. In proven areas 59 completions resulted in 31 producers and 28 failures. Unusual results were obtained during the year over a scattered area in northeastern Mexico near the United States border, where out of eight completions six were fair-sized gas wells. A wildcat dry hole was completed in Chocoy in an attempt to extend the Northern fields to the northeast, and another in Quebrache, to the southeast of the heavy-oil district. A deep test (10,168 ft.) through the Cretaceous lime into the Jurassic was completed as a dry hole in Metlal-toyuca, 9 miles southwest of the Old Alamo field on the Golden Lane.

Jan 1, 1937

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3

Jan 1, 1923

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967