Search Documents

By R. E. Cuthbertson

AN early appreciation by the management that Climax ore presented a challenging problem of economic concentration was responsible for the establishment, in June 1926, of an ore-testing department at the experimental plant of the Colorado School of Mines at Golden, some ninety miles from Climax. An engineering office was later organized in the same community for the design of all ore-treatment units erected at Climax during the period of rapid growth. Work of the ore-testing and design staffs was effectively co-ordinated under a common head. The primary reason for having the ore-testing and plant design departments in Golden, was to place these activities under the able supervision of A. J. Weinig, consultant for the Climax Molybdenum Co., and director of the experimental plant. A secondary consideration was the availability of excellent facilities for research in ore dressing in a highly favorable environment. Concentration of molybdenite by flotation from an ore of simple mineral composition does not appear, superficially, to present a serious problem in ore dressing but experience belies this apparent simplicity. The molybdenite content of average Climax ore is low and it is finely

Jan 1, 1946

By H. M. Davis, T. S. Jones

A methodfor accelerating the reduction of a metal oxide by carbon monoxide is to incorporate in the reduction system a nonreducible oxide which has a strong affinity for carbon dioxide and will remove it from the product gases. The effectiveness of this method was investigated by veduction experiments on specially prepared powder mixtures of SrO-ZnO ("active'.) and SrCO3-ZnO (reference). Measurements at 750o and 677°C showed that the rate of reduction of ZnO by CO was as much as an order of magnitude greater in the presence of SrO. Under the experimental conditions at least as much CO2 as generated by veduction was absorbed when SrO was present. Enlzancernent of the veduction rate by SvO resulted from modification of' gaseous djfitsion processes. THE specific question posed in this investigation was whether the reduction reaction CO + ZnO - Zn(g) + COa [1] could be accelerated by incorporating strontium oxide into the oxide charge undergoing reduction. Provided the strontium oxide was active enough, it could remove carbon dioxide from the product gases of ( 11 and form strontium carbonate, thus modifying Reaction [ 1] to CO + ZnO + SrO = Zn(g) + SrCO3 [ 2] This study of the comparative rates of Reactions [ I] and [2] can be considered as a particular case of a general scheme for increasing the rates of reduction of metal oxides by carbon monoxide. The limits of applicability of this scheme are indicated in the simple thermodynamic analysis presented in the appendix. This analysis primarily dictated the choice of the system, CO-ZnO-SrO, employed in this investigation. In addition, it was thought that a study of this scheme by use of the CO-ZnO-SrO reaction system would be of special interest in view of indications in the literature1-3 that the gaseous reduction of zinc oxide is prone to rate control by diffusion in the gas phase. The distinction should be pointed out between this and other efforts to increase the rates of reduction reactions through the use of addition agents. Additions of a wide range of chemicals have been tried with de- grees of apparent success varying from slightly negative to highly positive. The reasons for making additions have included the use of salts to produce effects akin to catalysis,4, 5 the alteration of the microstruc-tural details of the reduction process (including solid-state diffusion),6-8 and the conversion of an en-dothermic reaction into one that is exothermic or autogenous.9-12 The means used to attempt alteration of the enthalpy change has commonly been to incorporate lime into the charge, so that heat is generated by reaction with either of the reaction products, carbon dioxide or water. The use of lime in this way makes endeavors such as that of Edstrom and Wiberg similar to the present one. Furthermore, the basic principle behind the present work has previously been set forth.13 However, a detailed investigation of the type of reaction described in this work does not appear to have been conducted. EXPERIMENTAL PROCEDURE From both conceptual and physical standpoints, Reaction [2] is to be considered as the sum of two reactions:

Jan 1, 1968

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By Klaus Schwerdtfeger

The equilibria in the Cr-N system have been investigated in the temperature range 1100° to 1310°C by reacting chromium powder with Nz-Hz gas mixtures. The solubility of nitrogen in chromium in equilibrium with chromium subsitvide ("Cr,N") is given by Chromium subnitride is nonstoichiotnetric; its nitrogen content is always less than that corresponding to the formula CrzN. The lattice paranzeters of quenched samples have been measured; c, and a. parameters are found to increase with increasing nitrogen content. The growth rate of the subnitride layer on chromium plates was measured by a thermogravimetric technique, using a silica spring balance. The self-diffu-sivity obtained from the theoretical analysis of the parabolic rate constant is found to decrease with increasing nitrogen content, i.e., with decreasing vacancy concentration in the nitrogen sublattice. The intrinsic nitrogen diffuivity is derived from another series of rate measurements using "CrzN" plates; the intrinsic diffusivity, DN = 3.2 X 10-a cmZ sec-' at 1200 C, is found to be essentially independent of- the subnitride composition. The concentration gradient was measured in a chromium subnitride layer by the X-ray method and found to be consistent with the derived diffusivity value. TWO chromium nitrides are known to exist:' the nonstoichiometric subnitride "CrzN" and the nitride CrN. In the present work the kinetics of the formation of chromium subnitride from chromium and nitrogen have been investigated at 1100" and 1200°C. In additional experiments the relevant equilibria have been measured. The data are used to evaluate the diffusivity of nitrogen in chromium subnitride. Since chromium nitrides are often found in chromium-containing steels, the results are expected to be helpful in the interpretation of the chemical reactions between chromium steels and nitrogen. Equilibria in the Cr-N system have been determined by several investigators.2"3 The rate of nitriding of chromium was measured by Arkharov et a1 .' in ammonia in the temperature range 800" to 1200°C. The parabolic rate law was observed. Due to the undefined nitrogen activity of the ammonia atmosphere, it is dif- ficult to interpret these rate data theoretically. An additional difficulty arises from the fact that the two-layer scale consisting of CrN and "Cr2N" was formed at the temperatures below 1030°C. The rate of nitriding of technical chromium (95 pct) was measured by Zaks in nitrogen at -1 atm in the temperature range 800" to 1300°C. EXPERIMENTAL METHODS The chromium samples were reacted with Nz-HZ gas mixtures in a vertical tube furnace, wound with Pt-10 pct Rh resistance wire. The gas-tight reaction tube was of high-purity recrystallized alumina. In nitrogen solubility measurements the nitrogen content of chromium was determined by the Kjeldahl method, on samples quenched in the cold part of the furnace. The nonstoichiometry of the subnitride and the nitriding rates were measured thermogravimetrically using a sensitive (+0.1 mg) silica spring balance. For the equilibrium measurements samples of 1 g of chromium powder contained in high-purity alumina crucibles were used. In order to remove most of the oxygen and nitrogen impurities from the chromium, the samples were initially annealed in purified hydrogen until a constant weight was obtained. The chromium plates (approximate dimensions 2 by 1 by 0.08 cm) used for the rate measurements were machined from ingots obtained by arc-melting of iodine-processed chromium. According to manufacturers' specifications the purity of the chromium powder was 99.9 pct Cr and that of the iodine-processed chromium 99.99 pct Cr. Our own spectroscopic analysis of the chromium powder yielded 0.02 pct Fe, 0.05 pct Mn, 0.05 pct Si, and 0.02 pct Ti as major impurities with all the other detectable elements below 0.005 pct. The nitrogen partial pressure of the gas phase was controlled by mixing prepurified hydrogen and nitrogen with constant pressure head capillary flowmeters. Oxygen and water vapor were removed from the mixed gas by passing it through columns of platinized asbestos (450°C) and anhydrone. The gas flowed upward in the furnace with flow rates of 300 to 500 cu cm per min (25"~). Gas tightness of the furnace system was ensured by pressure checks at regular intervals. The furnace temperature was controlled electronically in the usual manner. The reported temperatures were measured with a Pt/Pt-10 pct Rh thermocouple and are estimated to be accurate within ±$C The X-ray measurements were made with a Debye-Scherrer camera and a diffractometer using chromium radiation {\Ka = 2.29092A). EQUILIBRIUM MEASUREMENTS The experimental results of the equilibrium measurements are contained in Tables I to In. Fig. 1 shows the solubility of nitrogen in solid chromium in the temperature range 1100" to 1310°C. In Figs.

Jan 1, 1968

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

THE introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various "wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these, advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.' The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago' for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles'" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By ALEXANDER S. CORSUN

THE main orebody in the Hecla mine, Burke, Ida- ho, occurs along a nearly vertical shear zone in the Burke quartzite, with a substantial gouge and lamprophyre dike occurring in an irregular manner throughout the lode. The veins range from 3 to 40 ft. wide and dip from 70 deg. to 90 deg. There is 110 definite line of demarcation between the lode and the wall rock. Stringers of ore are often found in the wall rock for irregular distances. Horizontal but irregular quartz stringers are also found running into the walls and positions of the wall have a tendency to break to the quartz stringers and the accompanying gouge, which causes indefinite, uneven and extremely heavy side and top pressures.

Jan 1, 1930

By Shun-ichi Satoh

In the previous paper, the writer indicated that the arc welding of cast iron is practicable only when barium carbonate is used to retard the fusion of electrodes. Later, he tested the effects of 48 other elements, to discover the cause of their retarding action. Wrought-iron bars 33 cm. long and 0.53 cm. dia. were used as electrodes. The chemical analysis of the original electrode is given in Table 1. Table 1.—Analysis of Electrode Per Cent. Carbon.................................................. 0.045 Silicon................................................... 0.028 Manganese....................................... Trace Phosphorus.............................................. 0.047 Sulfur................................................... 0.008 Each of the bars was wound with a twine of asbestos (1 mm. dia., weighing 0.5 g.) and then was coated with a mixture of equal quantities of graphite and carborundum and one of the compounds listed in the second column of Table 2. The method used in coating was as follows: The mixtures were reduced to paste by adding to them a solution of water glass (1:3); they were next put in a glass tube of 8 mm. inner diameter, with funnel-shaped mouth (the same tube shown in the previous paper); then the bars were passed through the tube so that the mixtures were coated on them. The glass tube was used only as a means of making the diameters of all coated bars exactly 8 millimeters. The cast iron was deposited on the steel plates by connecting the electrodes first to the positive and then to the negative pole of the generator. The figures representing the time, voltage, amperes and energy required to melt each electrode are given in Table 2. They are arranged in the order of the atomic weights of the elements contained in the coatings. In Figs. 1 to 4, which show respectively the time, current, voltage and energy required in this operation, the abscissas indicate the atomic weights of the elements contained in the coatings, and the ordinates

Jan 1, 1929

By H. T. Wyatt, A. S. Baptie

The Ten Section field is approximately 10 miles southwest of Bakers-field, Kern County, Calif. (Fig. 1). There is no surface evidence of the existence of the Ten Section structure, which subsurface exploration has shown to be a gently folded, anticlinal dome. Regionally, this field occurs as a fold in the deeper beds of the gently rolling floor of the San Joaquin Valley. It is on the easterly slope of the valley, its position with relation to the axis of this syncline not having been determined. The field was discovered by Shell Oil Co. with the completion of well Stevens A-l, on June 2, 1936, at a depth of 7888 ft. The location for this

Jan 1, 1938

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Zinc difhsions in gallium arsenide having surface concentrations as low as 5 x 10'' atoms per cu cm have been attained. A multiple-difhsion sequence is employed during which zinc enters the gallium arsenide from a silicon dioxide film in a solid-to-solid diffusion step. The technique is illustrated for the case of a zinc surface concentration of -1 x 1017 atoms per cu cm and a junction depth of 1.2 p. Radiotracer measurements of -0.1-p layers of gallium arsenide are used to delineate the resulting profile. A diffusion coefficient for zinc in pyrolytically deposited silicon dioxide is reported. ZINC is frequently used as an acceptor impurity in gallium arsenide. As examples, p-n junctions are formed using zinc-diffused layers in solar cells, lasers, and varactor diodes. For these purposes surface concentrations of 10'' to over loz0 zinc atoms per cu cm are desired and readily obtained from a vapor source. Diffusion of zinc into gallium arsenide to yield surface concentrations of about 1017 atoms per cu cm, however, is more difficult. For instance, oldstein' reports that large changes in the vapor density of zinc produce only small changes in surface concentration. Such low surface concentrations are necessary in forming the diffused base of a gallium arsenide double-diffused n-p-n transistor in order to obtain an adequate emitter efficiency. An alternative approach to zinc diffusion which can provide reduction in surface concentration of several orders of magnitude is the introduction of the diffusant from a solid source. This can be conveniently accomplished by using oxide films of the type generally employed for selective diffusion masking. Such oxides also serve to prevent the dissociation of the gallium arsenide surface at the high temperatures of diffusion. DIFFUSION PROCEDURE Fig. 1 illustrates the diffusion sequence which is employed for obtaining zinc surface concentrations in the range from 5 x lom to 1 X 10" atoms per cu cm. The description of technique will be given for the instance of -1 x 1017, which is typically utilized in double-diffused gallium arsenide transistor investigations at this laboratory. Tin- or germanium-doped gallium arsenide wafers drawn from crystals grown by horizontal Bridgman or Czochralski techniques are used, with bulk concentrations ranging from 1 to 3 X 10" carrier atoms per cu cm. Each wafer is chemically polished on the (iii) arsenic face using a mixture of five parts concentrated sul-furic acid, one part water, and one part 30 pct hydrogen peroxide at room temperature, followed by rinsing in deionized and quartz-distilled water. Pyrolytic silicon dioxide was chosen as the oxide coating because of the high quality of the films obtainable, the ease of their preparation, and the excellent control over film thickness and uniformity.

Jan 1, 1964

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

By W. A. Tiller, J. P. McHugh

HE majority of liquidus and solidus surfaces in phase diagrams have been determined by the conventional cooling- and heating-curve techniques.' These techniques have two main shortcomings: 1) the solidus may be in considerable error due to the difficulty involved in completely homogenizing the solid and 2) the determination of liquidus and solidus in more than a two-component system does not enable one to determine tie-lines connecting the specific equilibrium solid and liquid compositions. However, in a recent paper by one of the authors,' a method was suggested whereby the liquidus and solidus surfaces plus tie-lines in an n-component system may be determined. This method utilizes a controlled solidification technique and assumes that interface equilibrium exists during freezing. The present work was undertaken with a twofold purpose; first, to determine the liquidus and solidus lines in the pseudo-binary system Bi2Te3-Bi2Se3 by heating- and cooling-curve techniques and, second, to determine the partition coefficients of Te and Se in the BizTe3-,Sex system by controlled solidifica- tion techniques. The two sets of results can be compared to test the accuracy of the controlled solidification method. EXPERIMENTAL I—The starting materials for this study were 997999 pct Bi, Te, and Se, obtained from the American Smelting and Refining Co. The compounds BizTe, and Bi2Se3 were each prepared by melting together stoichiometric amounts of the elements, followed by twelve zone-refining passes. This produced homogeneous bars of the compounds for use in the phase-diagram studies. The apparatus used to obtain heating and cooling curves is illustrated schematically in Fig. 1. The alloy samples were located in a graphite crucible placed in a stainless steel canister. The canister was supported in a heavily lagged pit furnace by a device which oscillated the canister about its vertical axis at a frequency of about 3 cycles per sec during heating and cooling-curve runs. The graphite crucible was designed to minimize the thermal coupling of the sample to the furnace. A thin graphite sleeve separated the alloy sample from the stainless steel tube that housed the thermo-

Jan 1, 1960

By J. B. Clemmer

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgC03), usually is associated with lime-stone (CaCO3) and dolomite (MgC03 CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amor-phous) forms.2 The more common crystal-line mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories.

Jan 1, 1940

A High-speed Dilatometer and the Transformational Behavior of Six Steels in Cooling. By Arthur L. Christenson, Edward C. Nelson and Clarence E. Jackson. (With discussion).................................606 Dilatometric Studies of the Graphitization of Cast Iron. By N. A. Ziegler. With discussion) 627 An Interferometer Type of Dilatometer and Some Typical Results. By- L. '4. WIlley and W. L. Fink. (With discussion).........................642 The meeting was held in the Pine Room of the Statler Hotel, Cleveland, Ohio, on Tuesday afternoon, October 17, 1944. The chairmen were F. M. Walters, Jr. and Howard Scott. Introduction F. M. Walters, Jr.—The principal advantages of the dilatometric method perhaps are two, as compared with the method of thermal analysis. One is that the dilatometric method can be applied with a large variety of rates of heating and cooling, whereas thermal analysis—that is, the study of the transformational characteristics by means of heat evolution—is limited to the rates of heating and cooling that reveal the evolution of heat. The dilatometer can be used for the study Of reactions at zero rates of heating and cooling; that is, isothermal reactions. As you will hear this afternoon, the rates have been pushed up as far as 500°C. a second. The other advantage is that the dilatometric method shows that a two-phase region is a two-phase region, whereas the thermal analysis merely reveals the temperature at which the rates of heat evolution are greatest.

Jan 1, 1945

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By Noel S. Christensen

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The commercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depend¬ing upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943