Search Documents

By R. A. Pasternak, B. Evans

A dynamic technique for the determination of solubilities of gases in metals has been explored, using the N-Nb system as a test case. An initially clean sample, maintained at constant high temperature, is exposed to the gas at low pressure: the rate of sorp-tion and the corresponding change in sample resistance are measured continuously. A pronounced decrease in the slope of the resistance concentration curve is observed at the terminal solubility. The rate of gas uptake by the sample was determined in an ultrahigh-vacuum flow system equipped with a servo-control which maintains constant pressure in the sample chamber; the system and the technique have been described in detail elsewhere. 1,2 The sample was held at constant temperature during sorption by maintaining approximately constant power input into it; this results in constant temperature, since the emissivity of a metal is independent of moderate concentrations of dissolved gas. The simple electrical circuit used both for heating and for resistance measurement is shown in Fig. 1. The power input into the filament is where R is the filament resistance, RL is an adjustable resistance in series with the filament, and VT is the constant dc potential of the power source. If RL is set equal to R at the beginning of an absorption run, the power input becomes insensitive to subsequent resistance changes; for example, an increase of 20 pct in sample resistance is accompanied by a decrease in power input of less than 0.8 pct; i.e., the

Jan 1, 1967

Prof. Henry M. Howe, New York, N. Y. (communication to the Secretary*):—The results presented in Mr. Mathewson's paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min. from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the removal of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis.

Jan 1, 1908

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By S. Fugleberg

As a result of research work done during the planning of the Kokkola zinc plant it was found that a very efficient cementation of impurities from the suspension obtained after leaching copper and cadmium cakes was achieved by adding zinc dust to the batch without filtration after the leaching. All elements nobler than cadmium are precipitated with the exception of lead, which must be removed in a separate step. Using pure zinc dust, free from noble metals, the cadmium sponge produced will only contain elements that can be re- moved from cadmium by meltrefining. The process is thus : 1. Leaching and purification 2. Removal of lead (with BaCO3) 3. Precipitation of cadmium sponge with pure zinc dust 4. Meltrefining of briquetted sponge with NaOH for removal of Zn (and others) The paper deals with the removal of the most critical elements, i.e. Co, Ni, As, Sb, Cu, Pb, T1 in the liquid phase and Zn and T1 in the melt. A survey is also given of the behaviour of most of the other elements normally found in Cd raw material, such as Ge, Te, Se, Sn, In, Ga. It is shown that in most cases the benefit of an electrolysis in Cd production is very limited. In Kokkola 99.998% Cd is achieved by this method, but in favourable cases it may be possible to come quite close to five nines.

Jan 1, 1973

The General Electric Co., in cooperation with the Montana School of Mines and under a research grant from the Anaconda Co., is presently experimenting on a new non-explosive method of breaking rock with radio-frequency electrical power. The method is known as electrothermal forcing. It must be understood that present equipment has not been designed to perform primary blasting functions. Its conceived use will be restricted to small pieces of rock too large to pass through a chute or grizzly. However, even this use is still far in the future. Experiments to date have been limited mostly to rock smaller than 18 in.

Jan 11, 1961

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of' 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 ' and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By Charles L. Guettel

The temperature coefficients of electrical resistance of 31 alloys in the nickel-rich corner of the Ni-Cr-Fe system were determined. The results indicate that a range of binary Ni-Cr alloys has lower temperature coefficients than a specific region of Ni-Cr-Fe alloys which has been reported and quoted by others as providing the lowest coefficients in the ternary system. DESIRABLE properties of resistivity and temperature coefficients of resistance have been the basis for the successful commercial application of various Ni-Cr and Ni-Cr-Fe alloys. In particular, low or negligible temperature coefficients of resistance are necessary for wire used in precision wire wound resistors and potentiometers involved in closely controlled electrical and electronic circuitry. Alloys most successfully applied to this purpose basically have not been ternary Ni-Cr-Fe alloys but rather heat-treated Ni-Cr alloys in the region of approximately 73 to 79 pct Ni and 20 pct Cr with significant additions of other elements such as aluminum, silicon, iron, copper, manganese, and cobalt. While the addition elements play a vital role in the nature and control of the temperature-resistance curve of any one of these alloys, the inherent relatively low temperature coefficient of the binary Ni-Cr base composition itself in the approximate region of 80 pct Ni and 20 pct Cr contributes fundamentally to the eventual negligible temperature coefficient obtained with the applied alloys. W. A. Dean 1 has reported mean temperature coefficients (20' to 100oC) of as-cast samples for the Ni-Cr-Fe system, the nickel corner of which is given in Fig. 1. Dean had to use as-cast samples because alloys from a considerable region of the system were unworkable. Dean refers to the work of Hunter and sebast2 who used annealed wire samples to show that, for chromium contents of 10 to 25 pct, the temperature coefficient increases as the iron content is increased at the expense of nickel. Although the data of Hunter and Sebast were limited in the nickel-rich areas to eight samples of 60 to 91 pct Ni with only four samples containing iron, the possibility that no Ni-Cr-Fe alloy has a lower temperature coefficient than certain binary Ni-Cr alloys should have been given serious consideration. However, Dean's work has been referred to by J. S. Marsh,3 who, quoting Dean, states that for the temperature coefficients "the smallest values-about 0.0001 per oC (100 ppm)—were found for alloys containing about 55 pct Ni and 20 pct Cr" (balance iron). A region such as that reported by Dean would be significant to those trying to develop alloys for the applications described. Therefore, a series of three-pound laboratory open-air induction melts of Ni-Cr and Ni-Cr-Fe alloys were melted, conventionally processed to 0.005 in. diam wire, and continuously strand annealed at 1900° F. The basic Ni-Cr compositions, with balances essentially iron other than usual minor impurities, and the corresponding temperature coefficients of resistance and resistivities are given in Table I. The resistivities are approximate and are not to be considered as a basis for relating them to their position of composition in the ternary system. The wire diameters were determined with a micrometer, and not by weight and density measurements which would be required for accurate resistivity values. However,

Jan 1, 1963

By Frank A. Crossley

The work described has one serious shortcoming: grain size was not monitored during heat up to the temperature (1675°F) of isothermal anneal. The chief obstacles to p grain growth in titanium a-ß structures are the a grains. Heating a structure such as that shown in Fig. 1 to a temperature close to ß transus causes dissolution of a grains in order to adjust the a/ß ratio, compare Figs. 1 and 2. During this process there is a concomitant growth of the ß grains—otherwise ß grains would have to be nucleated in order to adjust the a/ß ratio. When the annealing temperature is reached the a/ß ratio stabilizes and this initial phase of ß grain growth ceases. After an incubation period growth resumes as described. Some 0 grain boundaries can be clearly seen in Fig. 1. (Skilled metallography commonly produces photomicrographs which show more structural detail than direct observation.) These boundaries suggest that the average ß grain size is approximately 0.002

Jan 1, 1970

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,1 and his experiments have been described and summarized by Richards1 White's contributions seem to have passed unnoticed by Fahrenwald, 2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,4 USSR; Anselm5 and Grunder,6 Germany; and Rose and Evans,[6] Great Britain.

Jan 5, 1958

By Thos Gibson

THE object of taxation is the raising of a revenue. Unless a tax accomplishes this, it is a failure. The right to take for public purposes a part of the moneys obtained from the carrying on of private enterprises is an attribute possessed only by a lawful government, and may indeed he called the supreme attribute of government. In free, democratic communities this power must of necessity rest upon the consent of the governed. Power implies obligation, hence it is obviously the duty of a government, in framing a system of taxation, to provide one which, while effective in producing a revenue, is also just and impartial. It will be conceded that mines and mining property ought to bear a fair share of the public expenditure. The question is, upon what basis taxation should proceed. Two separate taxing principles are usually contended for: Taxation should be proportionate to the benefits received by the person or property taxed; taxation should be based on ability to pay. A third is sometimes added, taxation should have reference to the extent and value of the natural resources enjoyed. As applied to mining taxation, it is pointed out by those who support the first mentioned basis that, mines being usually situated in rocky and hence sparsely peopled regions, mining companies are frequently obliged to construct roads, railways, telegraph and telephone lines, schools, water and sewerage systems, and many other amenities and conveniences of civilization, the cost of which in regions better suited for agriculture and consequently more thickly populated, has either been defrayed locally, or can be spread over a sufficiently large taxable group of people to materially lighten the financial burden on the mine. The mining com¬pany, it is argued, having made these outlays, should receive credit for, them and be relieved of taxation to a corresponding extent. There may be some force in this contention, but the situation is capable of relief without attempting to place taxation upon so unworkable a basis as the value of benefits received. Who is to be the judge of these benefits, and how are they to be valued? The very existence of a mining company and its ability to carry on business in peace and security, depend on the prevalence of law and order, which is a result of good government. The state provides protection against violence, and courts of law for

Jan 4, 1919

By C. A. Stetefeldt

IK the dry-crushing of ores, either by stamps, rolls, or other machinery, it is essential that the material should be free from moisture. Hence a contrivance which effects this with economy, and is of durable and compact construction, is a great desideratum. It is claimed for the below-described shelf dry-kiln, that it possesses these qualifications in a high degree. The construction of the shelf dry-kiln is based on the Hasenclever principle. That is to say, a number of inclined shelves are arranged zig-zag above each other in a vertical shaft, having openings or slits where they meet, on which the ore rests in a stratum, the thickness of which is governed by the width of the slits and the inclination of the shelves. If a portion of the charge is removed at the end of the bottom shelf, a sliding motion of the ore takes place on all shelves above, and the top shelf is replenished from a hopper set over it. It will be seen that the shaft is divided by the shelves into a number of triangular prismatic spaces. Through these the hot gases from a fireplace are made to circulate, each space communicating with the next one by a flue arranged in the sidewall of the shaft. These flues being located on alternate sides of the shaft, a continuous passage is formed through the whole structure. After thus stating the principle of the construction, its details will be easily understood by reference to the drawings, Fig. 1 to Fig. 5. The drawings, Fig. 1 to Fig. 4, represent two kilns united into one structure. The cast iron shelves(a) are 2 feet 4 inches wide and 5 feet long, with sides and a back 4 inches high, and are cast a full halfinch thick. How they rest on the brackets(d), and interlock each other, is shown in Fig. 5. Three such shelves, with an inclination of 38') are placed in one row in a brick shaft 7 feet 1/2 inch wide and 4 feet deep. The ore hoppers(g) rest on the iron bems(f). At the end of the bottom shelves are the discharge-doors(b), with shoots projecting beyond the front wall. A swinging apron(e) keeps the ore in place. By dropping it a car below the shoot is filled with dry ore. A number of extra-large pieces of ore may cause a stoppage in the slits ; for such an emergency the openings(e) are provided, through

Jan 1, 1884

By George B. Clark

THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry1 has suggested that a solution may be reached in one of two ways: 1-the usual approach, use of judgment based on experience; or 2-mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation.

Jan 8, 1954

By Henry Fernald

THE accounting system or bookkeeping methods of any company are principally the concern of that company and of those who are in control of its affairs. Its published financial report is, however, primarily intended for those who are not already fully informed regarding its operations and finances. Whatever may be the advantages of standardization of accounting and bookkeeping methods, it must be admitted that a company has a certain right to handle its accounts and keep its books and records in whatever manner may seem to it best adapted to its affairs, even though such methods may differ materially from those generally adopted by others. In its financial reports it should not, however, either ask or expect that the statements it makes or the terms which it uses will be given in its case a meaning and interpretation different from that which they are ordinarily considered to have in similar reports and statements of other companies. The particular form and arrangement of such reports is a matter concerning which there may be much difference of opinion. It is of little importance whether current assets come first or last in the Balance Sheet, but it is important that there should not be included under this designation any items which are not properly current assets within the generally accepted meaning of that term. The extent to which stockholders or others interested are to be made acquainted with the full details of a company's business is a question which the proper authorities must in each case decide. It should, however, be recognized that there are certain facts regarding a mining com-pany which must be set forth in a financial statement if it is fully to cover the conditions and affairs of the company. For example, a financial, statement which does not include or is not accompanied by a statement, of the ore reserves of the company does not fully set forth its financial condition. This is true whether the absence of such a statement of ore reserves is because it is not desired to make public the figures or whether it is because the ore reserves themselves are not definitely known, or accurately measured.

Jan 1, 1928

E. P. Pfleider, University of Minnesota I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. R. H. Merrill, U. S. Bureau of Mines, Denver Federal Center The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability. G. A. Leonards, Purdue University I was interested in Mr. Lane's observations concerning the correspondence between rate of slide movement with rise of reservoir. Perhaps the most interesting feature is that the rate of movement at the time the rock slope failed was less than the rate at an earlier time when it did not fail. This is difficult to explain from current slope stability theory. K. S. Lane, U. S. Army Corps of Engineers I believe that reduced rate of movement is the result of the progressive type of failure, such as described by Patton and Deere. which occurs along the sliding surfaces. It is difficult to analytically define the progressive failure condition for inclusion in slope stability conditions, but its existence should be recognized in design. We should also realize that many apparently stable slopes undoubtedly contain overstressed regions. To design a slope with no overstressed region would be uneconomical and conservative. D. H. Deere I would pose the question-"What is the meaning of a factor of safety of one?" We were involved in the design of a large, irregularly shaped, underground cavity with an unsupported span of several hundreds of feet. Tests on rock specimens indicated a strength of 1300 lb per sq in. The RQD would have been between 90 to 100 percent indicating excellent structural continuity. In-situ stress determinations indicated an approximately hydrostatic state of stress at a level of 1400 lb per sq in. Calculation of stress concentrations at the walls indicated that the stresses there would be about 3000 to 4000 lb per sq in. Admittedly the rock is in a confined condition everywhere except at the very skin of the wall and the rock walls would thus on the average be somewhat stronger. Allowing for the effect of restraint the factor of safety was found to be less than 0.5 over a region several feet into the wall. Construction was started, using rockbolts only to support the walls. Failure around the immediate skin occurred after each

Jan 1, 1967

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.' The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.' No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957

By O. R. Wagner, R. O. Leach

Immiscible displacement tests were performed in a consolidated sandstone core over the interfacial tension range from less thdn 0.01 to 5 dynes/cm to better define how interfacial tension (IFTJ reduction can lead to increased oil recovery. Data obtained were displacement efficiency at breakthbrough vs IFT for both drainage and imbibition conditions. These tests simulate water flooding under oil-wet and water-wet conditions, respectively. Results of the study have shown that displacement efficiency under both oil-wet and water-wet conditions can be markedly improved by a sufficient reduction in IFT. In the particular porous media used and for the low pressure gradients employed, the IFT must be reduced to a value less than about 0.07 dynes/cm to achieve increased recovery at the time of breakthrough of the injected phase. Below 0.07 dynes /cm, further small reductions in IFT result in large increases in displacement efficiency. Observed increases in recovery were obtained at pressure gradients which are well below those which can exist in the interwell area of a reservoir under water flood. The effect of pressure gradient on recovery is discussed. INTRODUCTION A residual oil saturation remains in rock which has been water flooded because, under usual reservoir conditions, the driving force which can be generated is inadequate to expel oil trapped by capillary forces. Since these capillary forces can be reduced by reducing the IFT a frequently studied method of increasing oil recovery has been the use of surfactants to reduce the water-oil interfacial tension. Mungan l observed improved recovery in both water-wet and oil-wet systems at 1.1 dyne /cm IFT, finding that the amount of improvement was greater in oil-wet systems. Moore and Blum,2 working with visual flow cell micro-models, con- cluded that recovery cannot be improved in water-wet systems by injecting surfactant solutions. They calculated that, for a pressure gadient of 1 psi/ft in their model, the IFT must be reduced to 0.03 dynes/cm to release oil trapped under water-wet conditions. Berkeley et al.3 indicated that, at representative field flooding rates, the IFT must be reduced to 0.001 dyne/cm to improve recovery, Thus, there is a wide variation of opinion about the IFT levels needed to improve recovery under field conditions. These previous investigators all have used as their experimental method the addition of surfactants to the injected water. The use of surfactant solutions to reduce IFT creates two experimental problems: (1) the loss of surfactant through adsorption on reservoir rock can obscure the true IFT value which exists at the displacement front, and (2) at very low values of IFT emulsifica-tion of oil and water commonly occurs. It is difficult, therefore, to determine whether the increased recovery is caused by IFT reduction as such, or is instead caused by emulsification. Also the properties of the available surfactants limit the IFT range which can be studied. In the present study the purpose is to better define how interfacial tension reduction can lead to increased oil recovery. A matter of great interest is the amount of recovery improvement potentially achievable in this way. The study was made using very low pressure gradients which was well within the range achievable by water flooding in the interwell region of petroleum reservoirs. A unique experimental approach was chosen to avoid adsorption and emulsification problems, and to allow convenient control of IFT. The fluid phases used were the equilibrium vapor and liquid phases of the methane-n-pentane system. The interfacial tension level was varied by changing the equilibrium pressure of the methane-pentane system over the range from 1,200 psia to near the critical pressure (2,420 psia). All tests were performed at a controlled temperature of 100F. The IFT-vs-pressure relationship for the methane-pentane system was based on the data of Stegemeier and Hough,6 and on new data obtained in this study. With this experimental approach it has been possible to study displacement at lower values of IFT than have been previously investigated.

Jan 1, 1967

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962