Search Documents

By F. C. Langenberg

DURING the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point: The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the. bars was tested in this manner and in no instance could any difference in structure be detected between the three specimens.1

Jan 2, 1915

By R. DiBella, H. Biloni, G. F. Bolling

A study of the detailed relationship between solidification substructure and microsegregation in dilute tin alloys has been continued. New observations reveal that depressions form at the solid-liquid interface not only as an initial form of segregation but throughout the range of increasing constitutional supercooling. In order to show the importance of this node formation it proves convenient to make two simplifications. Although substructure changes continuously as constitutional- supercooling increases,&apos; the following discrete stages may be used for discussion: 1) the planar solid-liquid interface; 2) ordered nodes, or depressions at the interface;&apos; 3) two-dimensional or elongated cells;3 4) regular or hexagonal cells;4 5) distorted cells, or hexagonal cells with branches;4 6) dendrites. It is also convenient to ignore observations made near grain boundaries which interact with the cellular substructure.2-4 And, it should be clearly pointed out that all singular depressions at the solid-liquid interface will be called nodes. Heretofore, the term "node" has been used without clear justification to describe both the truly isolated depression and the junction of cell walls appearing in a later stage of segregation. This usage is continued because it seems proved by the observations. Standard systematic growth of tin crystals was undertaken over a broad range of constitutional supercooling using various added solutes. Except for one or two chance observations, this research failed to reveal any appreciable range of growth conditions over which a disordered array of isolated nodes exists. Even though &apos;some finite range of random instability must exist, it is now concluded that stage one passes very rapidly to stage two. Next, after confirming that stage two passes to stage three by the elongation of isolated nodes: a reexamina-tion of stages three, four, and five followed. Standard metallography showed that pockets of higher solute concentration (for ko < 1) became more numerous in cell walls the more severe the growth conditions. These high-concentration regions must arise from depressions; however, in stage three their segregation is not distinguishable from the segregation of the nodes which join cell walls together. It seems, therefore, that the presence of nodes is causal in the formation of new cell walls, and that the mechanism by which stage three passes to stage four is initiated by nodes. If a similar reasoning is followed, the separation of stage four from stage five appears to be just a convenience that has arisen from the decanted interface observations made in the past. The present observations again show that more severe growth conditions relate directly to an increase in the number of nodes in the hexagonal cell walls. These nodes apparently serve as the origin for lines of segregation extending within the body of a cell, and can thus be assumed to represent the earliest form of branching,* as shown here in Fig. 1. The examination of stage six involved decanted-interface structures as in Fig. 2, which are similar to those considered by Rutter and Chalmers,5 Plaskett and winegard,6 and Hellawell and Herbert,7 and where distinct protrusions are each surrounded by a depressed boundary. The corresponding microsegregation behind the interface, but not far enough behind to allow a smearing of the segregation because of diffusion,4 is shown in Fig. 3. Both the shape of the decanted interface and the segregation pattern behind it

Jan 1, 1968

By AIME AIME

THE stage is set for the 1930 Annual Meeting. It will take place in the Engineering Societies Building. Feb. 17, 18, 19 and 20, and an unusual pro- gram of technical papers, symposia, lectures and addresses, interspersed with luncheons, dinners, excursions and worthwhile entertainment for the four days has been arranged. The curtain rises on Monday morning and the first act is by the entire company-registration. Then the meeting hits its stride, for there are ten technical sessions on Monday, and the range of subjects includes most of the Institute membership. The Committee on Coal and Coal Products, which is about to become the Coal Division, presents a symposium of a dozen or more papers on Coal Classification, concluding its afternoon session with several papers on general subjects. At its luncheon between sessions, C. E. Bockus, president of the National Coal Association, will be the honored guest. Papers of theoretical character will be discussed at the morning session of the Committee on Geophysical Prospecting; at its afternoon session there will be presented summaries of results obtained at various properties by methods described at previous meetings of this group and permanently recorded in "Geophysical Prospecting," published by the Institute early in 1929. Members of the Petroleum Division should not overlook the paper by Theodor Zuschlag, on this Committee&apos;s program. It is entitled, "Oil Structure Mapping by the Sundberg Method." Members of the Iron and Steel and Institute of Metals divisions will find it profitable to attend the session on Engineering Education on Monday afternoon. E. A. Holbrook has arranged a program of ten-minute talks on Metallurgical Education which are designed to get down to "brass tacks." and the practical man may, in discussion, contribute as well as learn. At 5 p. m. Thomas T. Read will lecture+ at Columbia University, on "Recent Progress in Economics of the Mineral Industries."

Jan 1, 1930

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

By J. N. Ong

The oxidation of tantalum is assumed to occur by four simultaneous first-order chain reactions; solution of oxygen in the metal, nucleation and growth of a suboxide phase at the metal surface and two phase boundary processes which give rise to two different modifications of Ta2O5. A rate equation is then formulated which accounts for all principal details of oxidation behavior, unifies and correlatss the results of the principal investigations, and expresses the rate as a function of pressure, temperature, and time. For purposes of practical application, the expressions: may be used below and above 700T respectively to determine the regression rate of tantalum in cm per hr, where T is to be expressed in "K and P in atmospheres pressure of oxygm. The equations will reproduce within a factor of two all reported experimental rates in the temperature range 475" to 1400°C and pressure range 0.000026 to 40.8 atm 0. 1 HE oxidation kinetics of tantalum have been investigated thoroughly in the temperature range 50" to 1400 and pressure range 1.32 x l0-&apos; to 40.8 atm pressure of 0,and as a result, the principal features of the oxidation of tantalum are known and have been described in considerable detail. The exposition of the characteristics of the behavior of tantalum in oxygen has been largely descriptive, with considerable attention being devoted to elucidating the structure, composition, and morphology of the resulting oxide products. The weight change vs time results have usually been reported graphically. With the exception of the linear rate below 700 C and the process of diffusion of interstitial oxygen into the metal,6&apos;9 no effort has been made to characterize the reaction rates in functional form. It is the purpose of this paper to demonstrate that when the fundamental principles of chemical kinetics are rigorously followed, the results of the principal investigations will be correlated and unified and the oxidation rale may be expressed as an analytic function of pressure, temperature, and time. In addition to accounting for the temperature and pressure dependency of the oxidation rate, the following minor features will be accounted for as a result of the basic analysis: the initial period of nonline-arity in rate at low temperatures, which decreases with increasing temperature;3&apos;5&apos;7 the rate vs temperature cusps obtained at constant pressure"5 the concentration gradient of oxygen interstitially dissolved in the metal.5&apos;7 The analysis will also be consistent with the overall chemistry of reaction and with all visual, microscopic, and X-ray observations. DEVELOPMENT OF RATE EQUATION As a fundamental basis for the treatment of metal-oxygen reaction kinetics, it will be regarded that the rate of reaction is determined by the concentration and not the activity or chemical potential. It is further assumed that all metal-oxygen reactions are first order complex chain reactions" whose rate is dependent on the concentration of an intermediate species which is a complex function of the oxygen concentration, or oxygen pressure, only. The basic rate equation is therefore: is the weight of oxygen consumed by the reaction, A is that portion of the area of the metal over which the reaction is occurring (cm2), t the time (sec), kf the rate constant for forward reaction, C the intermediate species concentration and f &apos;([Oz]) and f (Po,) are complex functions of oxygen concentration and Oxygen pressure respectively. Reverse reactions may usually be neglected in metal-oxygen systems since a large negative free energy generally accompanies these reactions. Eq. [I] takes different forms when the rate of reaction is controlled by diffusion into or through a phase or at a phase boundary. For diffusion into the metal phase, the rate is given by1&apos; Di is the diffusion coefficient of species diffusing into the metal phase (cm2/sec), and Q is the corre-

Jan 1, 1962

By S. Andrew Kulin, L. Kaufman

A general treatment of the broadening of X-ray double-crystal spectrometer rocking curves due to distributions of tilts and strains has been carried out. The results of this treatment have been applied to the case where dislocations in a crystal give rise to both tilts and strains. On this basis it is found that the rocking-curve halfwidth due to imperfections in the crystal, ßC , increases with increasing Bragg angle, 8. These considerations predict linear relationships between & and tan2 , and ßCand tan 8, for Gaussian and Cauchy distributions of dislocations, respectively. The zero intercept of the ßC us 8 curve, which is a measure of the degree of imperfection of the crystal, is found to depend directly on the distribution rather than the number of dislocations. In addition, the slope-intercept ratio for the ßc - ? curve has been calculated for both the Gaussian and Cauchy distributions. Experimental determination of the - 8 curves for a series of copper single crystals prepared by the Bridgeman and Czochralski methods yields results in agreement with the calculated slope-intercept ratio for a Cauchy distribution of dislocations. CERTAIN X-ray techniques have been used to study the perfection of single crystals. Gay, Hirsch, and Kelly have considered the spreading of spots into arcs on Debye-Sherrer rings due to imperfections. The Double-Crystal Spectrometer has also been applied to this problem.2 The characteristics of Double-Crystal Spectrometer Rocking Curves have been described in the literature by various workers.2-4 By assuming a random spacing of dislocations which give rise to a Gaussian distribution of misorientations relative to some mean orientation in a crystal Gay, et al.,1 arrive at the conclu- sion that the most probable misorientation is given by where h is the spacing between dislocations, and 8 and are the relative misorientations of neighboring regions. If ßC is the halfwidth of the rocking curve (the width at one-half the peak intensity) due to dislocations in the crystal then5

Jan 1, 1960

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.&apos;. &apos; It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:&apos;. &apos; Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.&apos;. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "&apos; The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By W. A. Tiller, D. H. Lane

A simple zone melting technique for investigating the effect of ultrasonic irradiation upon ingot solidification is described. The effect of i) ultrasonic power level, ii) freezing velocity, iii) constant or variable frequency, iv) direction of irradiation, and v) transducer-cozlpling bar joint upon the grain size of type 316 stainless steel have been investigated. The results of this study support the postulate that the ultrasonic vibrations increase the nucleation probability in the layer of liquid adjacent to the freezing interface. In the first paper of this series,l the possible mechanisms whereby ingot structure may be altered by irradiating a solidifying melt with ultrasonic vibrations have been discussed. A new technique for efficiently introducing the ultrasonic energy into the solid-liquid interface region was presented and applied to ingot preparation by the consumable-electrode arc-melting technique. The experimental results support the postulate that the ultrasonic vibrations may refine the ingot structure by increasing the nucleation probability in the zone of liquid adjacent to the solid-liquid interface. The present paper describes the application of the same technique to a relatively simple laboratory-scale zone-melting apparatus. This apparatus is found to be well suited to the detailed study of ultrasonic technology in this area and allows one to determine, in particular, the minimum ultrasonic power level needed to produce a certain grain size in a particular material. The results of this study support the nucleation mechanism for grain refinement, but do not provide any deeper insight into the specific nucleation mechanism responsible for the effect. EXPERIMENT The apparatus used in these experiments is shown in Fig. 1 and illustrated schematically in Fig. 2. The material to be studied, type 316 stainless steel, was in the form of a 3/4-in. sq bar 30 in. long. This bar was placed in a square open-topped mold with open ends made from high-purity graphite coated with a flame-sprayed Al2O3, skin. Surrounding the crucible was a molybdenum susceptor with 3/8-in. diam holes spaced at 1-in. intervals along its length to serve as sight ports. A tapered transducer horn was brazed to one end of the specimen. The entire assemblage was enclosed in a quartz tube, the transducer itself projecting out one end and resting in a cooling tank. A vacuum seal between the coupling bar and the end plate enclosed one end. A similar plate and seal enclosed the other end. The system is gas tight and can be operated under vacuum or an inert atmosphere. For these experiments, flowing argon at 15 in. of Hg pressure was used. The heat source for melting the stainless steel specimen was a 2-in. long 3-kc induction coil placed around the quartz tube; this source heated the susceptor, inductively melting about a 3-in. zone of the sample by radiation. To move the molten zone at a specified rate, the induction coil was moved down the tube at this rate with the aid of a simple pulling device. Thus, the sample could be irradiated at varying ultrasonic frequencies and power levels and could be solidified at varying rates. The power input to the transducer was measured using a "John Fluke Model 120 VAW-Meter." 1 The power delivered to the interface region is probably only about 50 pct of that measured on the VAW-meter. In a typical run, when the ultrasonic power was turned on, the interface of the molten zone closest

Jan 1, 1961

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.&apos; When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,&apos; since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

The following officers were elected by the Pennsylvania Anthracite Section of the A. I. M. E. on the evening of June 28th. Chairman, R. V. Norris; vice-chairmen, C. F. Huber, W. G. Whildin, W. J. Richards, Eli Conner; executive committee, Douglas Bunting,. W. W. Engle, Chas. Enzian, J. M. Humphrey, A. B. Jessup, R. A. Quinn; secretary and treasurer, Paul Sterling.

Jan 9, 1919

[SATURDAY, FEBRUARY 16 10 am to 5 pm Council of Section&apos; Delegates SUNDAY, FEBRUARY .17 1 pm Student Relations Committee 2 pm Board of Directors 2:30 pm MIED-Mineral Economics Instruction 5:30 pm MIED-Cocktails and Buffet Supper 7:30 pm MIED-Mineral Education 8 pm IMD-Program Committee]

Jan 1, 1952

By Clinton H. Crane

DR. TILNEY, the great expert on the study of the development of the brain of human beings and animals, tells us that the greatest difference between the human brain and the brain of animals is that man alone has shown evidence of being able to predict the future. Just why he throws overboard the busy bee who lays up honey for the winter, the squirrel who gathers nuts, and the humble ant, I do not know. At any rate, it is nice to be assured by an authority that we have this power of prophecy. My own experience with attempting to prophesy the future has convinced me that our only possibility of being good prophets is to be good students of history.

Jan 1, 1940

By Dorsey Hager

North Central Texas has recently become a center of interest for the oil men of America. The bringing in of the McClosky well at Ranger, Eastland County, and the shallow pool at Brownwood, Brown County, in 1917, has stimulated interest in this area to fever pitch. Oil men from all over the United States are now investing there. The area of present interest is shown by the accompanying map (Fig. 1). The money spent in leases runs into millions of dollars. It is no exaggeration to say that a strip of country 200 miles (321 km.) long and 125 miles (201 km.) wide, comprising some 15,000,000 acres (6,070,310 ha.), has been leased practically solid at a cost for rentals and bonuses of at least $1 per acre. The test holes contracted for will certainly number 400, at a cost of at least $5,000,000. From what has been done in the past six months, $20,000,000 at least will be spent. To pay returns on this amount of money, new production to the extent of at least 12,000,000 bbl. must be obtained. At present, the production from new fields will not average over 5000 bbl. per day; three wells at Ranger are producing 3000 bbl.; 250 wells at Brownwood produce 1000 bbl.; and the Gray well, Coleman County, is as yet an unknown factor. However, at Ranger there is every indication of developing a good pool covering from 1500 to 2000 acres (607 to 809 ha.), more or less, but the wells are deep, 3400 to 3800 ft. (1036 to 1158 m.), and cost $35,000 to $40,000 to drill. Large wells are necessary to pay for such expensive holes. As new wells are drilled, the gas pressure will be lowered rapidly, and large production need not be expected. For those oil men who expect a second Cushing or an Eldorado, Ranger holds little of promise. At Brownwood, Brown County, there are some 250 shallow wells (depths from 200 to 350 ft.) averaging 4 to 7 bbl. per day. There is a chance of an extensive producing area for these shallow sands to the southwest, and the opening of several thousand acres of shallow oil territory, and also some promise of deeper oil horizons in the Ranger horizon, but probably all under 2500 ft. At present, the lease brokers and speculators, and only a handful of oil men, have made any money. More fields must be developed, and it is more particularly with these possibilities that this paper deals. Lack of water for drilling purposes has undoubtedly held back development so far this year; this part of Texas has had a drouth for two years and there is an actual scarcity of water. Geological investigations so far undertaken cover nearly all the area outlined, and while pakt of the

Jan 1, 1920

By Michael Hoch, Walter C. Wyder

The isothermul section of the Nb-Ti-Zr-O system at 1500°C was investigated using X-ray dzffraction and metallographic techniques. UP to 66.7 at. pct 0, the system contains nine four-phase regions. Tsopleths at 10, 20, 30, 40, 50, and 55 at. pct 0 weye constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of niobium, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct. O., PREVIOUS INVESTIGATIONS The Ti-Zr-O system was investigated in this laboratory.&apos; The binary systems of interest have been compiled and discussed by anssen2 and Levin, McMurdie, and Ha11. Elliott4 has determined the Nb-O system by metallographic and X-ray diffraction techniques. He shows the existence of three oxides, namely NbO, NbO2, and Nb2O5. At 1500°C the solubility of oxygen in niobium is about 4 at. pct. No solid solubility region is shown for either NbO or NbO2. EQUIPMENT The same equipment as that for the study of the Ti-Zr-O system was used. The X-ray diffraction patterns were analyzed with the help of the ASTM card set5 and NBS circulars.6 MATERIALS The niobium powder (99 pct pure), the titanium powder (99.6 pct pure), the niobium pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmount Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., N.Y. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure," the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE Samples of the desired compositions were made up, in mole pct, from the materials listed above. In some cases the intermediate binary compounds, such as NbO and TiZrO4 were prepared beforehand and used in the preparation of the samples. This technique enabled equilibrium to be reached from two sides. The components of each sample were mechanically mixed in a mortar and pestle and pressed into 3/16-in. diam pellets. The pressures used in compacting were of the order of 50 to 100 x 103 psi. Sintering was accomplished by heating the samples in a tungsten crucible (3/4-in. high, %-in. diam, 1/8-in. wall, lid with XB-in. hole). The pellets were separated from each other and from the crucible by means of small spiral coils of tungsten wire placed between the stacked pellets and on the bottom of the crucible. The sintering time was from 4 to 12 hr at 1500°C under a vacuum of 6 x 101-5 to 1 x 10-6 mm of Hg. All samples were reground after the first or second heating repressed, and reheated. In most cases: equilibrium was obtained after the first heating, as the X-ray diffraction pictures after each heating remained unchanged. Quenching of the samples from 1500°C was at first only possible by allowing the crucible and its contents to lose heat by radiation. The temperature dropped from 1500° to 900°c in approximately 1 1/2 min, which was considered adequate when compared to the times used by other investigators to reach equilibrium in the temperature range of 1000°c and lower. Later, a new technique for faster quenching of the samples was cleveloped. This technique involved the removal of the samples from the crucible, whereupon they were quenched by coming in contact with the water-cooled copper base of the furnace. This manipulation was performed without breaking the vacuum. The sample pellets were placed on a tungsten wire rack inside the crucible. The wire rack passed through the hole in the crucible lid, where it was connected to a small nonmagnetic chain. The chain was fed to the side of the furnace by means of a brass rack which fitted between the body and lid of the furnace. Suspended at the end of the chain, near the furnace wall, were three magnetic washers. With the use of a strong

Jan 1, 1962

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1&apos;3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine&apos;s earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine&apos; systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By Ramkrishna Agarwal

The problem of the measurement of in situ stresses in rock masses has, in recent years, become one of the prime concerns of investigators and researchers in the field of rock mechanics. Numerous instruments have been developed for that purpose and various techniques have been used to determine the absolute values of these stresses at a point.l The "stress-relief" technique has gained the widest acceptance. In its usual application it relies on one of the two following principles: (1) Measurements of the changes in a "solid inclusion" in a borehole,2 or (2) Measurements of the diametral deformation of a borehole with a free boundary." The theoretical development, in the case of the latter, is based upon an evaluation of the deformation of a circular hole in an infinite plate under the action of a uniaxial stress field. Expressions for the deformations may be obtained by using either the plain strain or the generalized plane stress theoretical approach of the classical theory of Elasticity, which assumes that the material is linearly elastic, homogeneous and isotropic. The solution for the case of a biaxial stress field is obtained by the Principal of Superposition. The circular hole becomes elliptical after deformation takes place under the action of a uniaxial or biaxial stress field applied to the plate. In the practical application of the technique, the reverse procedure is applied. A borehole is drilled in the rock and a deformation-measuring

Jan 1, 1968

By Worthen Bradley, R. G. Hall

THIS paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer to the Bradley Mining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a rotary kiln at the same end-that is, of course, the upper end. This is as opposed to "counter-current firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. EARLY REFERENCES The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,1 its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver . . . is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and flies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake County, California. The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank. Reed and Sulphur Bank ranked respectively fifth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: Sometimes there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of . . . the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away. as its richness and value were not

Jan 1, 1945

By Harry A. Lipsitt, Rollins E. Hook, Attwell M. Adair

A necessary condition for a uniaxial stress distribution in compression testing is that the specimen end surfaces make full contact with the apparatus compression plates. In addition all compression surfaces must be machined perpendicularly to the loading axis. In general this condition is not sufficiently fulfilled in a simple apparatus. Therefore on application of the load the compression plate may first touch the specimen at one point only. This may cause crumbling of the specimen if the material under investigation is brittle (e.g., ionic crystals). It also precludes a precise study of the beginning of deformation as the effective cross sectional area is unknown. In addition a complex stress state is set up which renders quantitative work impossible, e.g., on dislocation density and arrangement as a function of stress. To overcome these difficulties a "self-adjusting" upper compression plate is required. A simple and reliable method of achieving this is shown in Fig. 1: A steel hemisphere is placed on the specimen. As soon as the compression plate (which no longer needs precise machining) makes contact with this hemisphere the load is uniformly distributed over the whole specimen surface, and a homogeneous uniaxial state of stress results. An advantage of the method is that the loading is always central, even when the specimen surface is not parallel to the compression plate (Fig. 1, dashed line). Therefore to a first approximation a uniaxial state of stress is maintained if the misorientation of the specimen end surface is small. Two typical stress strain curves of identically prepared sodium chloride crystals are shown in Fig. 2; curve 1 was taken without and curve II with the hemisphere under otherwise identical conditions. The improvement in the accuracy of defining the beginning of elastic and plastic deformation is clearly indicated. The writer wishes to thank the Deutsche Forschungsgemeinschaft for financial support, and Professor P. Haasen for providing facilities for this work.

Jan 1, 1962

By J. F. K. Brown

ANTHRACITE?S satisfactory showing in 1942 was accomplished in the face of adverse conditions, such as the loss of man power to the active services and to other industries, and the difficulty and delay in obtaining the necessary materials and equipment required in mining operations. Although the in- creased output was stimulated by the war, and thus does not impress one as contributing to continuing improvement in the industry, nevertheless the year witnessed several efforts ant1 consideration of others that have the appearance of permanent progress.

Jan 1, 1943