Search Documents

By Alexander L. Field

The Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity apparatus, furnace and other accessories mentioned in this paper have been described fully in s Bureau of Mines report.1 The Literature on Slag Viscosity The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method .or other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity., the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300" C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 1, 1917

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By P. Chiotti, J. T. Mason

Thermal, X-ray, metallographic, and resistivity data were obtained to establish the phase diagram for the Yb-Zn system. Six intermetallic compounds and five eutectics have been identified. The compounds position at 695°C. No evidence for the compound YbZn,, was observed. Whether this compound is stabilized or inhibited by small amounts of impurities is uncertain. SEVERAL aspects of the Yb-Zn system have been reported in the literature. Much of this work deals with the crystallographic identification of some of the compounds. The YbZn compound has been reported by Iandelli and palenzonal and the YbZn, structure and thermal data for the composition range between YbZn and Yb3Znll have been reported by Michel et al. A compound of uncertain stoichiometry in the range 60 to 68 wt pct Zn with a cubic structure has been reported by Kuz'ma et aL4 The YbzZn17, YbZn,,, and YbZn13 compounds have been reported by both Kuz'ma et a1 and Iandelli and Palenzona.' YbnZn17 has also been identified by Laube. This investigation was undertaken to establish the phase diagram of this system. Ytterbium in many respects behaves as an alkaline earth rather than a rare earth metal6 and it is of interest to note the resemblance between the Yb-Zn system, the Ca-Zn,' and typical rare earth-zinc systems.g'10 MATERIALS AND EXPERIMENTAL PROCEDURES The materials used in this investigation were Ames Laboratory ytterbium and Bunker-Hill slab zinc, 99.99 pct pure. Analyses of the ytterbium showed 38 ppm Ta, 82 ppm 0, and 15 ppm N with Ca, Cu, C, Mg, Al, Si, Cr, Fe, Ni, Sc, Y, Er, Tm, and Lu all less than 50 ppm. The ytterbium was dehydrogenated by heating in tantalum under vacuum for 8 hr at 900°C. The metal was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys in the composition range between ytterbium and Yb2Zn17. With higher zinc concentrations the tantalum was penetrated by the alloy and failed after several days at temperatures of 600" to 700°C. Approximately 20 g of zinc and ytterbium metal were sealed under argon in *-in.-diam tantalum cruci- bles equipped with thermocouple wells. The crucibles were in turn sealed in stainless-steel jackets. The alloys were equilibrated in an oscillating furnace and given various heat treatments in a soaking furnace. The steel jackets were removed and differential thermal analysis data were obtained under an atmosphere of argon. The thermal analysis apparatus was calibrated against the melting points of pure zinc, aluminum, silver, and copper and found to give thermal arrests within 1°C of the accepted melting temperatures for these elements. The thermal analysis apparatus has been described in an earlier paper.g Alloys were further heat-treated as necessary and subjected to metallographic examination and X-ray diffraction analysis. Most alloys were etched with Nital (0.5 to 10 pct nitric acid in alcohol). EXPERIMENTAL RESULTS The results of the thermal analysis are summarized by the points on the phase diagram, Fig. 1. Six compounds and five eutectics were observed. The eutectic temperature and compositions in weight percent zinc are 491°C and 12 pct, 645°C and 32 pct, 687°C and 54 pct, 742°C and 67 pct, and 750°C and 77 pct. The compounds YbZn, YbZn2, Yb2Zng, Yb2Zn17, and YbZnll melt congruently at 650°, 751°, 75Z°, 754", and 755"C, respectively. The compound Yb3Znll undergoes a peritectic decomposition at 695°C. The transformation and melting temperatures for the ytterbium were observed to be 797" and 817°C. re-

Jan 1, 1969

By T. D. Yensen, N. A. Ziegler

AGING is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in nonferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the Al transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, 0, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2.

Jan 1, 1935

By E. T. Turkdogan, M. L. Pearce

The rates of sulfurization and desulfurization of calcium aluminate, silicate, and ferrite melts by CO + CO2 + SO2 mixtures at 1550°C are reported. It is shown that for melts 10 to 15 mm deep transport of sulfide ions within the melt controls the rate of sulfur transfer. The rate data from shallow melts, i.e., 1 to 4 mm deep, have been analyzed on the basis of a diffusion or a reaction controlled process and indications are that the both processes may play a part in controlling the rate of sulfur reaction. The rates of desulfurization of silicate XVEACTION equilibria between metals, metal oxides, and gases have received considerable attention in recent years. However, the understanding of and aluminate melts increase with increasing PCO2/PCO ratio in the gas stream, the effect being most marked for aluminate melts. The sulfide equilibrium data obtained from the present work are shown to be in accord with the results of previous studies. It is shown that carbon dioxide has a measurable solubility in silicate, aluminate, and ferrite melts. Consideration is given to the partial equilibria which control the directions and the rates of reactions occurring simultaneously in complex heterogeneous systems. the kinetics of heterogeneous reactions, particularly those occurring at elevated temperatures has not been improved appreciably. Almost all the metallurgical reactions occur in heterogeneous systems involving two or more phases. Although in many authoritative text books and original Papers the basic principles concerning the kinetics of heterogeneous reactions are clearly underlined, they are seldom used to the best advantage in kinetic studies, particularly those involving the metallurgical reac-

Jan 1, 1963

By T. D. Yensen

AGING is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more con-stituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the Al transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, 0, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2.

Jan 1, 1935

By Leonard H. Goldman, Harold E. Marr

The PGT uranium assay probe is a borehole tool developed by Princeton Gamma-Tech over the last several years. It has the ability to do an in-situ assay of uranium in the presence of any amount of disequilibrium. It has some advantages over coring including cost, speed of analysis, and accuracy. In this paper we would like to give a brief description of the measurement and then show some sample logs from South Texas. Uranium exploration and development is carried out primarily by gamma logging since uranium daughters are prolific emitters of gamma rays. The conventional gross gamma tool for uranium logging is limited in value because of the inability of this tool to distinguish uranium from its daughters and other naturally occurring radioisotopes, such as potassium and thorium. This problem becomes severe in cases of disequilibrium. Disequilibrium, in a geological context, is defined as the condition when the gamma radiations from the daughter products are being emitted in a location different from that of the parent uranium. In the decay chain of uranium almost all the gamma radiation emitted in the entire chain comes from the daughter product, bismuth-214. Bismuth-214 is separated from uranium by several long-lived isotopes that are chemically active and have different physical properties, often resulting in shifts in the location of bismuth- 214 relative to the parent uranium. In the United States orebodies exhibiting disequilibrium are a common occurrence and the use of a gross gamma log to delineate uranium orebodies can lead to errors. At present the solution to the disequilibrium problem is extensive coring followed by chemical analyses of the cores. There are several drawbacks in using this technique. First is the high cost of coring, the second is the fact that no results are available for days, or typically, weeks after the drilling is done. Thus for development work, coring and drilling must be done on a grid basis and many additional holes are cored to ensure that the entire orebody is mapped. Another disadvantage to cores is the fact that a small volume is sampled, the volume of the core itself. This leads to problems in the mapping out of the orebody when the ore de- posit is not very homogeneous. The PGT probe described in this paper is a new solution to the disequilibrium problem. Basically, the probe measures radiations that come almost directly from uranium itself. The first daughter of uranium, which is protactinium-234 (Pa-234), is only separated from uranium by a 24-day half-life and no disequilibrium problems build up in such a short time. The PGT probe measures the intensity of a one MeV gamma line emitted by Pa-234 and, using this information, calculates the concentration of uranium. The PGT probe is 24" in diameter and 12 feet long. The probe contains a microprocessor which passes the information to a larger minicomputer in the truck. All data is analyzed on site, and the results from a high speed printer are presented to the geologist. Data is also available on 9- track IBM compatible tape for further processing. The PGT probe output is linear with uranium concentration. The only correction factor is for borehole size, and that only becomes important in boreholes bigger than seven inches in diameter. Dead time is compensated in the probe itself and no problems have been encountered in ore zones up to several percent UjO8. In addition to the uranium assay, a conventional gross gamma log is plotted alongside. Grade thicknesses for zones above cutoff are calculated as well as disequilibrium factors. COMPARISONS During its commercial operation PGT logged a series of 18 holes that had been cored and assayed. All of the holes in this series were logged in normal operation by regular field operators. The time to log each hole was generally under an hour, and in typical operation a PGT logging truck will do between 7 and 8 holes a day. The results of the comparison of the PGT and the core assays are presented in a series of figures showing plots of the PGT assay, core analysis and gross gamma measurements. The first three figures show individual holes with the gross gamma plotted along with the core and the PGT assays. All three logs were from holes on the reduced side of a rollfront deposit in South Texas. In Figure 1 we see the two wings of the roll- front at 143 ft and 150 ft separated by a barren zone. The wings are well defined both by the PGT assay and the core. There is approximately a one foot shift which can be attributed to drilling errors. The gross gamma is showing a rather severe discrepancy, being considerably lower and not showing the barren zone. The grade thickness calcula-

Jan 1, 1980

By R. C. Wilcox, R. V. Lawrence, P. A. Calhoun

The V-Rh-Si, Nb-Rh-Si, and Cr-Rh-Si systems were investigated to evaluate the extent of solid solubility between binary Cr3O structures. All Cr3O components lie within the favorable atomic size range1 for the formation of the Cr3O structure. Previous studies indicated complete solid solubility between V3Si and V3Sn2 and no solubility between Sn and cr3si3 or Si and Nb3Rh.4 The Cr3O structure is not found in the Cr-Sn and Nb-Si binary systems. Powder compacts were are-melted under argon, homogenized in a vacuum at 1000°C, and water-quenched. Alloys containing greater than 15 at. pet Si were annealed 100 hr. X-ray diffractometer methods were used to study all systems utilizing copper radiation for the Cr-Rh-Si system and chromium radiation for the other two systems. V-Rh-Si System. The alloys prepared in the V-Rh-Si system and the measured lattice parameters for the Cr3O structure found in each alloy are listed in Table I. The characteristic Cr3O diffraction pattern was found in all binary alloys. The measured lattice parameter of V3Rh (VRS-1) is in agreement with the reported value5 while the value for V3Si (VRS-5) is only in fair agreement.' In

Jan 1, 1965

INTRODUCTION Porphyry copper deposits have been reported from the Caribbean area by Pease (1966), Cox, et al. (1973), Guild (1974), Kesler, et al. (1975), and others. This chapter summarizes the most widely known characteristics of those deposits. Only one deposit that conceivably can be classed as a porphyry copper occurrence is in production (Pueblo Viejo, Dominican Republic), but others are known whose tonnage and grade are of economic interest. Deposits in this province may be classified as copper-gold or copper-molybdenum types (Kesler, 1972), but deposits associated with quartz-rich plutons that have high Na2O:K2O and high gold:copper but low molybdenum: copper ratios dominate. Porphyry copper occurrences are reported in the literature from Puerto Rico, Haiti, the Dominican Republic, Jamaica, and Cuba. Only the porphyry copper deposits from Puerto Rico are extensively described in the literature; consequently the Caribbean porphyry copper province in general is not as well documented as the southern Cordilleran orogen. Because past published technical descriptions are incomplete, some data presented here are new to the literature. The Caribbean includes the island arcs between North and South America. Porphyry copper occurrences are known from the Greater Antilles, the generally east-west trending group of islands that lies south of North America. Fig. 48, therefore, only covers the Greater Antilles portion of the Caribbean. Porphyry copper deposits in this area are not described by the Lowell and Guilbert (1970) model in details of metallization (general paucity of molybdenum), alteration (scarcity of orthoclase), or petrography (preponderance of quartz diorite). Therefore, this model should be modified to include deposits associated with quartz-bearing plutons such as those found in the Caribbean. In the Meme deposit on Haiti ore occurs in skarn adjacent to the quartz diorite phase of a composite quartz monzonite-granodio-rite-quartz diorite pluton (Kesler, 1968). This deposit, with a K-Ar 66 m.y. date, is not included in Fig. 48 as a porphyry copper deposit because metallization is restricted largely to the intruded rocks. Although the intrusive rocks at the Meme deposit may contain sulfide near skarn contacts they are otherwise essentially unaltered. Porphyry molybdenum deposits as defined by Clarke (1972) have not been reported in the Caribbean area.

Jan 1, 1978

By A. H. Smallbone, R. Lathe

Considerable efforts have been expended to apply multiple regression techniques to quantitative determinations in x-ray fluorescence analysis. Multiple regression has been shown to be an effective method for correlating x-ray fluorescence intensities to elemental concentrations. Although many other techniques have been devised to solve the problem of matrix effects in x-ray fluorescence analysis, there are few as efficient in terms of storage requirement or ease of programming for digital computers as the multiple regression method. In the case of ore slurry, it has the additional advantage of allowing a unified approach to the problems of slurry density correction and matrix effect corrections. The data used in the present work were obtained with an on-stream x-ray analyzer capable of analyzing 15 slurry streams for as many as nine elements simultaneously. One of its fixed monochromators was set to accept scattered radiation at a discretely selected wavelength as a means of monitoring the slurry's pulp density. The data were reduced to obtain the correlation equations and a computer program combining slurry density with matrix corrections was written in FORTRAN IV to calculate concentrations.

Jan 8, 1969

By F. W. Glaser

Metal-carbon-boron powder mixtures were hot pressed and the resulting specimens were studied by X-ray diffraction. It was found that regardless of the starting combination of the metal, carbon, or boron powders, a metal boride phase was always the major component in these samples. In the absence of carbon the boride phase formed on hot pressing depended only on the amount of boron present. Two new phases of the system Ti-B were found. They are Ti2B and Ti2B5. The existence of a controversial face-centered cubic phase of formula TiB was confirmed. Electrical resistivities were measured for various boride phases. It was found that the diborides are generally better conductors than the monoborides of the same metal. THE carbides and borides of the transition elements have very high melting points, in the range 2500° to 4000°C, and are therefore of interest as high temperature materials. The literature on the stability or chemical reactivity of these carbides and borides is very scarce. Various investigators'-" have demonstrated a relative instability of certain carbide phases in the presence of boron or boron-containing substances. In a recent publication, Glaserl demonstrated the stability of zirconium-boride (ZrB,) in the presence of carbon at temperatures in excess of approximately 2900°C, while during a preliminary investigation of boride phases, Steinitz' concluded that the diborides are stable in the presence of carbon while the monoborides of the fourth and fifth group are not, forming diborides plus carbides instead. Nelson, Willmore, and Womeldorph" have elaborated on the reaction B,C + 2TiC = 2TiB, + 3C, which was known to occur because of a relative instability of B,C and the great tendency towards TiB, formation at relatively low temperatures (approximately 1200°C). A similar study, involving as starting materials TiO, and B,C and resulting in TiB,, was recently described by Honak4, who observed the beginning of an exothermic reaction of a Ti0,-B,C powder mixture, which, when preheated in a hydrogen atmosphere to approximately 950°C, was carried to about 1600 °C by the heat of reaction. To shed more light on reactions of this type (Metal-C-B), the final product apparently always resulting in a boride phase at the expense of a carbide phase," a systematic investigation was started * Boride phases of various metals, as reported to date, are listed in Table I. and the following is an account of some of the results that were obtained. Materials, Preparation of Samples, Testing Methods The raw materials employed for this work consisted of various carbide, boride, and metal powders. as well as of boron and graphite powders. In cases where commercial grades of carbides were considered unsuitable because of low purity or excessive amounts of graphitic carbon, such carbide powders were prepared by this laboratory. The procedure for the preparation of carbide powders (zirconium carbide, titanium carbide, tantalum carbide, and niobium carbide) consisted of mixing graphite and the respective metal hydride powders in stoichio-metric proportions and subsequent heating of such mixtures in a hydrogen atmosphere in carbon crucibles. The heating was by high frequency to temperatures ranging between 1700" and 2100°C. The resulting carbide was then comminuted and screened to the desired particle size. ZrB, and TiB, powders were produced by the electrolysis of fused salt baths, according to the method described by Andriex.. The borides of niobium, vanadium, tantalum, molybdenum, chro-ium, and iron were obtained by mixing the respective metal and boron powders in the desired proportions. Such metal-boron mixtures were heated in a high frequency furnace to form boride powders. For each metal-carbon-boron group (Tables I1 through XI) a metal, its hydride, carbide or boride were mixed with carbon, boron or boron carbide powders. The additions of carbon, boron or boron carbide powders to any of these metals or metal compounds were calculated to satisfy a particular carbide or boride phase that according to the literature (Table I) had definitely been established by X-ray diffraction work. Samples of powder mixtures were hot pressed in graphite molds that were heated by direct conduction. The specimen dimensions were approximately 2.5X1X1 cm. Hot pressing temperatures were measured optically and maintained for approximately 30 sec under a constant pressure of about 1.3 ton per sq in. Wherever possible, an attempt to obtain maximum specimen density was made by temperature variation. Electrical resistivity testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp, at room temperature. To obtain electrical resistivities for specific carbide or boride phases, values were plotted as a function of the respective sample densities

Jan 1, 1953

By Arthur La Motte

I NDUSTRIAL explosives, as distinguished from military explosives, include high explosives and blasting powder. The high explosives which are best known are straight dynamite, gelatin dynamite, ammonia dynamite and permissibles. There are two kinds of blasting powder, saltpetre blasting powder and nitrate of soda blasting powder. Blasting powders are mechanical mixtures of nitrate of potash or nitrate of soda with sulfur and charcoal, highly compressed, granulated and glazed. They ignite from a spark and burn with relative slowness, the rate of burning and hence the rate of conversion into gases depending upon the size of the granulation and upon the degree of. confinement under which the powder is placed. High explosives, on the other hand, are chemical compounds which detonate; that is, when the explosive is subjected to a violent shock, provided in practice by a blasting cap or an electric blasting cap, the molecule of the essential ingredient, usually nitroglycerin, is disrupted and the energy and heat released cause any other explosive ingredients which may be present, such as ammoniuin nitrate or T.N.T., to decompose with a resultant evolution of gases at an extremely rapid rate varying from 6000 to 20,000 ft. per second.

Jan 1, 1924

By J. S. Bowles

DISCUSSION, M. Cohen presiding J. W. Christian (The Inorganic Chemistry Laboratory, oxford, Englandl)—I was very interested in Dr. Bowles' results on the suppression of the transformation by solid films of alcohol or propane. The transformation in cobalt, which is also martensitic, can be explained by a mechanism involving the reflection of "half dislocations" down a series of atomic planes.* This reflection process is similar to that considered by Frank13 for plastic deformation on a single slip plane and, as he pointed out, reflection would be impossible if the metal were immersed in a liquid of higher density. It seems possible that solid films of alcohol have a similar effect on the lithium transformation. Reflection should also be possible at a grain boundary, though a higher kinetic energy of the dislocation, and hence a lower temperature would be required. As Dr. Bowles used coarse grained polycrystalline speci- mens, transformation on cooling should still have occurred in grains which did not form part of the outside (free surface) of the metal. This may account for the X-ray lines of the low temperature phase which were found. There is thus the interesting possibility that in a polycrystalline specimen a liquid, or in some cases a solid, film of material of or or higher density will lower M,, while in a single crystal it should suppress the transformation completely. In the case of cobalt it is necessary to find a dense liquid which will not react with the metal at the transformation temperature. The most promising liquid appears to be pure lead, but it is very difficult to devise a method of investigating whether or not this does suppress the transformation.

Jan 1, 1952

By AIME AIME

AT the Morenci branch of the Phelps Dodge Corporation, of which Frank Ayer is manager, several new types of machines that have been developed by Charles Mitchell, shop foreman in the drill steel shop, invite comment for their time and labor-saving qualities. Foremost of these is an adjustable gage-block and gaging device for attachment to drill-sharpening machines, developed and patent applied for by Mr. Mitchell. It replaces the blocks on the standard Ingersoll-Leyner drill steel sharpener No. 5. Features of the device are gage blocks with a flat surface which can readily be removed when worn and planed in any flat planer; blocks that can be adjusted with a templet to give a far more accurate gage than was formerly possible; and a center stop that is adjustable and can be accurately set to center any standard size drill steel.

Jan 1, 1930

By T. R. Wright

IN few mining regions in the world are the ores so varied and complex as in the Andes of central Peru. Consequently, in few localities is one company engaged in so many and such diverse metallurgical operations as the Cerro de Pasco Copper Corp. Concurrent with the mining of complex lead-zinc ores in Peru, and the consequent expansion of the Corporation's metallurgical activities, a department of metallurgical research was established in 1927 at La Orova. Facilities were provided for research in ore dressing, hydronivtallurgy pyrometallurgy, electrometallurgy, and analytical chemistry. In addition to laboratories. various pilot plants were built, including a concentrator, leaching plant, "by-product" smelter, and electrolytic refineries. These pilot plants are not diminutive units; they are designed and equipped as semicommercial plants for operation on a continuous 24-hour basis thus assuring the duplication of pilot plant results in actual practice. In general, the sequence in the development of metallurgical operations hasbeen as follows: (1) investigations in the laboratory to determine the most effective and economical method of treatment; (2) continuation of the research project on a pilot-plant scale when the evaluation of the laboratory

Jan 1, 1945

By AIME AIME

THE Tuesday afternoon session", H. A. Bedworth chairman and T. S. Fuller, vice-chairman, was opened with D. J. McAdam, Jr.'s paper entitled "The Influence of Cyclic Stress on Corrosion." This paper dealt with the influence of cyclic stress on corrosion of alloy steels, corrosion-resisting steels, monel metal and aluminum alloys. The paper was discussed by T. S. Fuller, who pointed out that steels under stress corroded more than unstressed steels when subjected to steam.

Jan 1, 1930

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and- sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, ,so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved, salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidably produced by the introduction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus 3/16-in. or plus 1/8-in. in the United States and plus 1/16-in. in Great Britain: Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about in. is made difficult by viscosity' effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By D. Turnbull, J. H. Hollomon, J. C. Fisher

The concepts of nucleation and of growth have adequately described the isothermal phase transformations to which they have been applied.ls2 However, these concepts have not yet been used successfully to describe the kinetics of a number of transformations that are not observed to take place isothermally. A typical reaction of this type is the austenite to martensite transformation in steels, for which the new phase appears only during cooling of the parent phase. If the cooling is interrupted, transformation ceases; yet had the cooling continued, transformation would also have continued. Nuclei of a new phase do not leap into existence all at once by the simultaneous cooperation of a large number of atoms or molecules of the parent phase; rather they are formed at finite rates by gaining or losing atoms one at a time from the surrounding materiaL3,4 Further thermo-dynamic considerations require a finite concentration of small transitory nuclei of all unstable phases to exist at equilibrium in a stable phase.= For steel in particular, nuclei of ferrite (a iron) exist at equilibrium in austenite (y iron) at temperatures where austenite is the stable phase. If a high-temperature phase a be cooled sufficiently rapidly from temperature TI above the a-ß equilibrium temperature To, to temperature T-1 below To where ß is the stable phase, the equilibrium distribution of ß nuclei corresponding to the high temperature will be retained. There are two limiting possibilities of particular interest: I. The steady state rate of nucleation of ß may be appreciable at T_1, and may require a concentration of sub-critical nuclei exceeding that retained from the high temperature. Time will be required then for the concentration of nuclei to build up to the steady state value, and an induction period will be observed during which the rate of nucleation will increase to the steady state value. 2. The steady state rate of nucleation of ß may be negligible at T-l, while the critical size for continuous growth of ß nuclei, which decreases with increased subcooling of the a phase, may reach a value so small that some. of the retained high-temperature nu-

Jan 1, 1949

By Roman Y. Poderny, Vladimir V. Rjevskii

In the USSR, the Moscow Institute of Radio Electronics tronics and Mining Electro-Mechanics (MIRGEM) has started what it hopes will become a nationwide movement to educate mining students in the precise specialties that industry has come to require. Courses for mining engineers, the MIRGEM faculty proposes, should dovetail as exactly as possible with specific jobs available in the mining profession. Acting upon this thesis, MIRGEM revised its own curriculum in 1962 and has since presented an over-all plan for Soviet mining education before two mining school conferences as well as the Ministry of Higher Education and a number of major Soviet industrial ministries. The plan was universally approved with some suggested revisions. SOVIET MINING EDUCATION TODAY At present, mining education in the Soviet Union covers the exploitation of solid minerals and raw materials, including coal as well as ferrous and nonferrous metals. The extraction, storage, and refining of oil and gas is treated as a separate discipline. In all, there are 33 Soviet universities and institutes that train mining engineers for careers in the industrial, research and educational fields.

Jan 9, 1966