Search Documents

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,' where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

By J. W. Gabelman

A study of spatial relations between uranium and other metal deposits and hydro thermally altered rocks in western Colorado demonstrated districtwide and regional zoning. The pattern was later found repeated elsewhere in the Western Hemisphere Cordillera. District mineralization centers are pipelike bodies of pervasively altered rock from which intensity-temperature-pressure gradients decreased outwardly. Uranium occurs in several zonal environments but usually is economic only in outermost zones. The general similarity of zones throughout the tectoni-cally and metallogenically uniform Cordillera may reflect a consistent hydrothermal process involving zoning. By determining positions of zones it should be possible to select for examination the most favorable small portions of districts or provinces. Mineralogical zoning has been discussed by Lindgren,l3 Graton,lo Emmons,' Blanchard,' Park and many others. It is commonly found to some extent in most mineralized areas. The existence of nonmetallic alteration envelopes around lode metal deposits and their relation to metallization were first emphasized by Lovering,l4 Burbank, Sales and Meyer," Sales,2o McKinstry,I7 Lovering and others15 and Schmitt. Also, large areas of nonmetallic alteration containing porphyry-type replacement metal disseminations have long been recognized and are described by Schwartz,25-28 Kerr and others" and Gilully. In some districts, e. g., Bingham Canyon, Utah, and Santa Rita, N.M., base metal lode deposits and their alteration envelopes are zoned around large altered areas which contain porphyry copper replacement disseminations; however, the spatial and genetic relations between lodes and replacement disseminations and their associated alterations do not seem to have received sufficient attention. Bodies of altered rock containing porphyry-type replacement disseminations are many times larger than the alteration envelopes containing lode deposits. The two types are rarely superimposed. They occur adjacent to or independent of one another, but they are believed to be related through the mechanism of zoning as suggested by Gabelman and Boyer. 5'6 Most of the significant lode metal deposits are distributed around central pipelike bodies of strong, pervasive, nonmetallic alteration which may or may

Jan 1, 1962

FIGURES covering appropriations recommended by the Budget Bureau for the Bureau of Mines at Washington for next year are now available and are as quoted below. APPROPRIATION BUDGET APPROPRIATION 1928 1929 General Expenses $ 86,000` $ 86,000 Investigating Mine Accidents 386,470 399,470 Mining Investigations in Alaska.. 10,860 10,860 Operating Mine Rescue Cars and Stations 327,630 342,630 Testing Fuel 154,000 158,500 Mineral Mining Investigations.... 99,570 125,000 Oil, Gas and Oil-Shale Investiga- tions 198,260 198,260 Oil-Shale Investigations 5,000 80,000 Expenses Mining Experiment Sta- tions 173,000 173,000 Care, etc., Buildings and Grounds, Pittsburgh, Pa 71,360 76,360 Maintenance and Operation, Fuel Yards Balance Balance Helium Investigations :.... 75,000 75,000 Helium Production and Conserva- tion 1,063,000 462.000 Potash Investigations 100,000 100,000 Economics of Mineral Industries. . 225,000 275,000 Totals $2,975,150 $2,562,080

Jan 1, 1928

By R. G. Grieves, G. Thodos

A method is presented for the accurate calculation of the cricondentherm and cricondenbar pressures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain six and quite possibly any number of components including paraffins, isoparaffins, olefins, acetylenes, naphthenes and aromatics. The approach is similur to that used for calculating critical pressures and cricondentherm and cricondenbar temperatures. The critical pressure, the normal boiling point and the approximate vapor pressure behavior of each component are all that art required. A stepwise culculation procedure is necessary for mixtures containing more than two components. From an analysis of 22 binary systems and 118 mixtures, the average deviation of calculated cricondentherm pressures from reported values is 2.4 per cent. For nine multicomponent mixtures the average deviation is 1 per cent. Considering 19 binary systems and 108 mixtures, the average deviation of calculated cricondenbar pressures from reported values is 1.7 per cent. For 15 multi-component mixtures, the average deviation is 2.2 per cent. INTRODUCTION A knowledge of the phase behavior in the critical region of multicomponent hydrocarbon mixtures is of value both in industrial processing operations and for the optimum operation of gas condensate reservoirs. Accurate methods of calculating the critical temperatures and critical pressures4,6,7,8,9,23 and cricondentherm and cricondenbar temperatures6p10 of multicomponent hydrocarbon mixtures are available in the literature. If the cricondentherm and cricondenbar pressures could be calculated with equal accuracy, the entire phase diagram of a multicomponent hydrocarbon mixture could be well approximated. The work of Etter and Kay6 is limited to systems containing the normal paraffins and has not been tested on systems containing a heavier component than heptane. In addition, the development of their multicomponent equations is based upon a limited number of mixtures containing from three to six components. Silverman and Thodos have considered systems containing both paraffinic and non-paraffinic hydrocarbons, but their correlation is limited to binary systems and is highly inaccurate for methane systems. Eilerts has done extensive work on the cricondenbar pressure; he has produced an excellent correlation for binary systems. However, his procedure for multicomponent mixtures is chiefly useful for highly complex mixtures requiring a knowledge of the vapor-liquid equilibrium behavior of the mixtures; he has not considered the cricondentherm pressure. The objective of this study was the development of an accurate and rapid method for the calculation of the cricondentherm and cricondenbar pressures of multicomponent mixtures containing all types of hydrocarbons and having a wide volatility range. The approach that was adopted is similar to that used by Grieves and Thodos for cricondentherm and cricondenbar temperaturesl0 and for critical pressures.9 However, methane systems had to be considered separately and a modified stepwise calculation procedure was utilized for the cricondertherm pressure. The correlations were developed in a manner similar to those for critical pressures and cricondentherm and cricondenbar temperatures. Based upon binary data reported in the literature it was observed that the ratios of cricondentherm and cricondenbar pressure to the pseudocritical pressure (molar average), pt/ppc and pp/ppc, respectively, in two-component systems depended upon the mole fraction of the low-boiling component and upon the diversity in properties of the two components. A dimensionless boiling-point parameter Tb,/Tb was chosen to represent the diversity in properties of the components. For a binary system, Ti,'is the molar average of the normal boiling points of the two components involved. For a multicomponent system it is either the molar average of the normal boiling points of all of the components involved or the molar average of the normal boiling point of the pure low-boiling component and of the atmospheric boiling point of the low-boiling-free mixture of

Jan 1, 1965

By M. H. Shumate

Rope-type haulage has had many applications in the mining and allied industries. Records have indicated favorable results both from a standpoint of efficiency and investment. The Truax-Traer Coal Co. has used some variations of rope haulage at their mines and preparation plants. They have built a system which solves their particular problems, and have an investment which has indicated an annual savings in operating costs. Rope haulage, as applied to the mining industry, goes back many years for both underground and surface mining, or a combination of both. The Truax-Traer Coal Co. has used gravity retarding hoists as well as several variations of rope haulage, including electrical and combinations of both, but each was limited in its use and application by natural conditions and economies of the operation. Several systems of rope haulage equipment are offered by manufacturers today for handling railroad car movement on a limited or continuous basis. The portal and railroad loading facilities of Truax-Traer Coal Co.'s Burning Star Slope mine, located in Jackson County, Ill., were moved in 1960. The old location was abondoned, eliminating 3% miles of underground track haulage. The mine was converted to an all-belt system, and coal is loaded at a new raw coal plant and shipped by railroad cars to a central cleaning plant. The company wanted to operate the surface facilities as efficiently as possible, employing a minimum number of workers, using the latest type railroad car movers. The existing rope haulage facilities at several locations throughout the country were examined and considered for the Slope mine location. The application of each appeared favorable but lacked flexibility, and it was difficult to justify the capital investment. The company decided to investigate the possibility of building a system that would apply to their problem, and have an investment that could be amortized in a relatively short period. SPECIFICATIONS They employed the services of Allen and Garcia Co. of Chicago, Ill. Through combined efforts, a railroad car rope system was designed to specifications as shown in Fig. 1. The Falk Corp. of Milwaukee, Wis. built the hoist to the specifications as shown in Fig. 2. It has an all welded base and pedestals. The all welded drum is not grooved. A single helical gear was used in lieu of herring bone type. A Falk speed reducer, Unit 90Y3-A, is driven by a 25-hp 1800-rpm, 440-V ac type 'C' (high starting torque) drip-proof, Frame 324-U motor. The speed reducer shaft is equipped with a solenoid operated ac spring set shoe brake, operating on a 7-in. diam. brake wheel. The dolly car, shown in Fig. 3, was field constructed, using the trucks and frame of a railroad tank car. Truax-Traer did not alter the frame but added plates and anchors for hoist ropes and frames for 8.5 tons of concrete to be used as ballast on the car. The limit switch operating shoe was also installed and the car coupler latch mechanism overhauled. The hoist rope selected was 1% in. in diam., 6x37 improved plow steel extra flexible, right lay, regular lay, with independent wire rope core, and preformed. Wedge sockets were used to connect rope to the dolly car as shown in Fig. 4. The system employs two 30-in. and three 16-in. diam. sheaves. All are bronze bushed and equipped with grease fittings. Larger sheaves are used for directional change of hoist rope and the smaller ones as snub sheaves to correct fleet angle of rope as it approaches the hoist drum. The Trench lay cable, buried between the two tracks, is used for electrical distribution and controls between hoists and operator's cab. Foundations for the system required 187 cu yards of reinforced concrete using approximately 60 cu yd each at three locations. Four hoists are employed in the system, two for each track. A pair is interconnected electrically and when one operates, moving the cars, the tail hoist idles with brake released. The process is repeated for the reverse direction. A limit switch, mounted in the track near each end of the system, is tripped by the dolly car as it approaches the hoist. The limit switch controls movement in one direction only, protecting the dolly car and establishing positive con-

Jan 1, 1962

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3'4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,'-' the segregation process became a successful industrial operation.'r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

Jan 1, 1888

By Z. F. Danes

Combination of gravity data and density logs makes it possible to determine the structural relief. Under a wide class of geologic conditions, the solution is unique, or limited to a single parametric system of solutions. As a useful byproduct, the method yields a new way to construct derivative maps, continue the field up or down, subtract regional anomalies, and perform smoothing. In the past, the problem of interpreting gravity anomalies in terms of structural geology was solved along two main lines: 1) A body of a certain shape and density contrast was assumed and the corresponding gravity anomaly calculated, analytically for simple bodies, graphically and/or numerically for more complex ones; then the computed anomaly was compared with the observed one, and the assumed shape corrected according to the differences between the two. 2) The anomaly is assumed to come from a warped interface between two media of different density; the relief of the warping is assumed small compared to the depth of burial, so that the structure can be approximated by a flat horizontal surface of variable density distribution. The first method is a standard technique, described in every text book on applied geophysics, and is well applicable, for bodies with predominant vertical dimension. The second one, probably first used by Tsuboi and Fuchida,' is mathematically more elegant. It applies to the fashionable field of integral transforms (Bullard and Cooper, 2 Tomoda and Aki, 3 Dean 4) and is useful mainly in cases when the vertical relief of the structures is comparatively small. 30th methods, tacitly or openly, assume a density discontinuity across the boundary of the two media, while within each medium the density is constant. However, the recent invention of the gamma-gamma

Jan 1, 1962

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By Ralph M. Roosevelt

IN AS MUCH as our Institute, by tradition, never adopts any official view of matters upon which difference of opinion exists, it may be taken for granted that the duty of its Production Control Committee does' not embrace the formulation of any general policy on that much-discussed subject. During the first years of its existence the Committee confined its activities to making arrangements for an annual general session at which the broader aspects of the general problem were discussed by men both within and outside the mineral industry. These general sessions, although interesting, did not indicate any definite path of progress, so during the last year the Committee has held a number of luncheon meetings at which the members might discuss in detail problems existing in the specific industries with which they are most closely acquainted, in the hope that discussions dealing with conditions rather than theories might result in the bringing to light of some general truths. Most of these truths have been fairly obvious from the beginning but they are of such basic importance that a periodic restatement of them seems worth while,

Jan 1, 1932

By Dean W. Lynch

Arizona: The San Xavier Indian Reservation mine is located approximately 2 ½ miles northwest of Asarco's Mission Mine southwest of Tucson. The company plans to produce oxide and copper-bearing siliceous ore at this operation, construction of which is scheduled for completion in 12 months. Asarco also plans a copper leaching and iron precipitation plant at its mine. The plant will leach 4000 tpd of oxide ore using sulfuric acid produced at the company's acid plant now under construction at Hayden. Copper precipitates will go to the smelter at Hayden. A drilling program at the Sacaton copper prospect in Pinal County, has disclosed two porphyry copper deposits. One deposit, mineable by surface mining, has approximately 17 million tons of material averaging 0.80% Cu. A deeper deposit suitable for under- ground mining has approximately 12 million tons averaging 1.5% Cu. Although Asarco intends to place this property in production, no startup date has been determined.

Jan 1, 1970

By A. F. Baker, E. R. Palowitch, A. W. Deurbrouck

As air-pollution regulations become increasingly more stringent, increased significance is being placed on the amount of sulfur present in coals used for steam generation. These regulations are aimed at minimizing the pollution of the atmosphere with noxious gases such as the sulfur oxides that are formed and emitted when coal is burned. Two meet these future requirements, a definite need exists to reduce the sulfur content of some of the coals used for steam generation. Reducing pyritic sulfur involves liberating the pyrite from the coal and then removing it. The specific gravity of pyrite is high (5.0) compared to that of coal (about 1.2, mineral-free), and standard coal-washing devices, such as wet concentrating tables, will efficiently remove pyrite particles larger than about 100 mesh. Particles below this size will be entrained in the table water and will be carried into the clean coal product. Techniques such as froth flotation are of little benefit for pyrite reduction because the flotation characteristics of pyrite are similar to those of coal.

Jan 6, 1966

By J. B. Cohen, M. B. Beaver, R. J. Black

RECENT investigations have shown that face-centered cubic metals may deform by twinning. Blewitt, et al' found that at 4.2"K the mode of def~rmation of single crystals of copper changed at large strains and markings formed on (111) planes. Later they- emonstrated by X-ray diffraction and metallography that the markings were twins and showed that favorably oriented single crystals of copper deformed by twinning at 78°K. They also observed twinning in silver and gold deformed at 4.2 and 78°K. Wagner3 obtained evidence for twinning from the peak shape of diffraction lines of silver cold-worked at 78°K, but twins small enough to cause such effects are not likely to be detected metal-lographically. In the work reported here lamellar structures were observed in deformed silver-gold alloys. They appeared to be mechanical twins, but metallography could not establish this conclusively. Their tendency to form depended on strain rate, temperature and composition. Specimens of silver-gold alloys (0 to 83 wt pct Au) were deformed plastically. One set was worked by hammering under liquid nitrogen, at room temperature and at intermediate temperatures. Another set was compressed slowly in liquid nitrogen to the same reductions as those produced by hammering. Tensile specimens (0.015 x 0.120 x 1.5 in.) of various compositions and approximately equal grain size (0.011 to 0.016 cm) were tested at -195°C and at room temperature. In microsections of all specimens deformed by hammering at —195°C thin lamellae appeared, Fig. 1. They were aligned in definite directions in each grain. In some grains they had two orientations. Where lamellae intersected, a displacement was apparent. Near the center of the left margin of Fig. 1 shear has taken place beyond the fully developed intersecting lamella. Many lamellae resembled Neumann bands in alpha iron. They were parallel to one side of triangular etch pits in the matrix (as in Figs. 1 and 2). The individual lamellae were narrow and had little substructure. This suggested that they did not result from concentrated local slip. The shape of etch pits within the lamellae differed from that of pits in the matrix, as can be seen in Fig. 2; this indicated a difference in orientation. Specimens slowly deformed at —195°C contained regions in which the lamellae were clustered. In these specimens some lamellae were bent and presumably had formed before the termination of the deformation. Structures of greater width than the lamellae were also seen.4 More lamellar structures formed on impact than during slow compression to a given reduction. This was true of all compositions. The structures became less abundant with increasing temperature of deformation. None was observed after extension to fracture at room temperature, but they could be pro-

Jan 1, 1959

By M. H. Caron

THE most outstanding property of ammonia liquors, used in the ammonia leaching process is their very limited ability to dissolve all compounds present in reduced ore except nickel and cobalt. Although they do have such a high degree of purity, even the smallest amounts of impurities contaminate the precipitate of basic nickel carbonate that may be obtained from pregnant liquors by straight distillation. Figures have been given in a separate paper regarding the extent of such contamination. The product of straight distillation is likely to contain small amounts of Fe, Mn, MgO and SiO2 as well as some sulphate and sulphide. The sulphur can be readily eliminated by calcination of the product at the proper temperature and MgO and SiO2 by reduction and melting of the metal with a suitable flux. After such treatment the metal is relatively pure, and the iron and manganese content will be very small. The cobalt content, however, may vary considerably, depending upon the ore treated. The metal obtained from pure true garni-erite ores usually has only a small cobalt content of less than 1 pct. Metal obtained from medium grade iron-rich nickel ores may show cobalt values from 2 to 3 pct, and the alloy obtained from laterite is likely to contain as much as 10 pct cobalt. By proper treatment a good deal of cobalt may be recovered from lateritic nickeliferous iron ores, and cobalt will become the major constituent of the pregnant liquor if asbolan ores or similar products are treated. The pregnant liquor of "run of mine" nickel ores may have a pinkish shade, indicating the presence of cobalt. It is evident that from such liquors the metals should be recovered separately. Even if cobalt is present in only very small amounts, it would probably be economically justifiable to recover both metals as pure as possible if a suitable process could be devised. The author has made investigations along this line and has patented some processes adapted to the treatment of this type of solutions. Selective Dissolution of Nickel from Basic Nickel Carbonate Containing Some Cobalt: Basic nickel carbonate obtained from true garnierite ores by straight distillation of the pregnant liquors, always contains some cobalt as well as the normal impurities. In. order to improve the quality of the nickel product and to recover most of the cobalt, the following process has been devised. By using liquors with a low CO2 to NH3 ratio, nickel can be redis-solved preferentially to cobalt. It is not a sharp and clean separation but a selective one, for the bulk of the nickel may be redissolved with a small amount of cobalt, and a small residue may hold the bulk of the cobalt. The greatly increased cobalt content of the residue is indicated by a pronounced olive green color, in contrast with the light green color of pure basic nickel carbonate. The following example is given from Dutch patent No. 52788, Klasse 40a. 43 granted June 17, 1942: The original precipitate contained about 0.55 pct cobalt calculated on total nickel + cobalt. Eight hundred and fifty grams of the basic nickel carbonate were redissolved in leach liquor containing 7.12 pct NH3 and 2.12 pct CO2. The weight of the dry residue was about 3.5 pct of the original weight. By analysis it was found that the residue contained: Fe 1.93 pct, Co 6.01 pct, Ni 34.87 pct and also a certain amount of silica. The clear filtered blue liquor was distilled and the precipitate of basic nickel carbonate from this analyzed: Fe 0.008 pct, Co 0.0146 pct, Ni 42.37 pct. It is obvious that this product is considerably more pure, since calculation shows that about 94 pct of the original cobalt remained in the residue. Cobalt and nickel can be recovered by further

Jan 1, 1951

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By Alan Kissock

MOLYBDENUM is thought of as one of the rarer elements, for though it occurs in almost every country of the world it is seldom found in commercial quantities. In this country, however, there is one deposit which makes the term "rare" a misnomer. There are two commercially mined molybdenum minerals: molybdenite, the sulfide, and wulfenite, a lead molybdate. Of these two only the former is of any con- sequence but wulfenite is of mineralogical interest. It is frequently associated with oxidized lead ores and particularly in arid sections. Deposits, however, are usually quite superficial. It is highly oxidized and yet it does not appear to be an alteration product for it apparently disappears below water level and I know of no case where primary molybdenite, or in fact any molybdenum whatever has been identified below these surface wulfenite occurrences. The genesis of wulfenite would make an !- interesting study.

Jan 1, 1933

By Jesse Jones

1. BRINELL tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base. babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin.

Jan 8, 1918

By W. E. Thorne

The object of this graphic method is to estimate the weight of the casting, which is to be made from a given pattern, when the cross-section is not a uniform geometrical figure. Such an estimate is a very important guide to the foundryman, who would otherwise guess at the probable weight of a casting of new design, and, in trying to be on the safe side, would probably melt an unnecessary amount of iron. It is also an aid to the designer of a new car-wheel pattern, who must otherwise estimate from general experience the probable weight, have test-wheels made, and correct the pattern afterwards, so as to obtain the weight prescribed. For the method here described, an accurate drawing of the pattern is employed. This gives a closer result than a drawing of the wheel itself, for the following reasons: 1. Calculations based upon the actual dimensions of the wheel involve the erroneous assumption that the specific gravity of the casting is uniform throughout; and upon that basis the calculated weight would be wrong, because the amount of metal poured has shrunk in the mould, acquiring the highest density in the outside chilled portion, and growing less dense through the mottled to the gray portions. 2. Calculations based upon the dimensions of the pattern or " chiller " assume that the cooled metal will not have shrunk, but will have the volume of the pattern and a uniform density. These assumptions, though erroneous, counterbalance each other. For instance, the patterns and the chiller which give a wheel 33 in. in diameter when cold, are respectively 33.5 in. in diameter. This shows a shrinkage for wheel-iron of about & in. (ordinary gray pig is commonly assumed to shrink about 1/8 in.) per foot. Wheels cast in 33.5-in. chillers do not always have the

Jan 1, 1903

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940