Search Documents

By Thomas P. Bispham

INTRODUCTION From the lender's point of view, the greatest period of risk in a project financing occurs during the construction phase. Therefore, most projects are supported during this phase by completion guarantees supplied by some credit-worthy entity; for example, the project sponsors in the case of a joint venture, such as that of W.R. Grace, Hanna Mining, and Liberty Capital; or by a strong contract with a utility or foreign importer/investor, such as the way North American Coal Corporation has structured many of its transactions. THE PROJECT LOAN REQUEST A project financing is a more complex form of term loan than one using an ongoing corporation's balance sheet as a credit base and, therefore, a potential lender will subject the loan request to a more rigorous analysis. To support this effort, the financial institution will require a more detailed information memorandum to evaluate the credit and technical risks of a project - especially since much of the necessary information is not otherwise available. (See also Gibbs and Sroka paper above in this Chapter) A well-prepared information memorandum will impress prospective lenders with the planning ability and general competence of management. Also, the process of preparing the memorandum will help management understand the true extent of the opportunities and limitations of its venture. Appendix A outlines the topics which comprise a complete information memorandum for a loan request. Of some interest to those seeking to sell a currently-operating mining venture, a similar information memorandum should be prepared i.e., covering the same topics discussed here, for the investment banker to use with potential purchasers. For that purpose, though, one might not want to prepare quite as much detail as for a lender. Appendix B outlines the elements of a reserve evaluation and feasibility study, often called the "Bankable Document." Usually, these studies are prepared by independent engineering consultants for use by potential borrowers and sellers. (Potential purchasers will often contract for a similar study for their use in evaluating an acquisition.) ELEMENTS OF A LOAN INFORMATION MEMORANDUM 1. Outline: The information memorandum should begin with a one-page outline covering such topics as: a. The borrower's name, address, and phone number. b. Principal contact at the borrower. c. Amount of the proposed financing. d. Desired pricing and structure of the proposed financing. This should include a description of the amount and source of equity in the proposed financing. e. Use of the proceeds and timing. 2. Summary: The most important information contained in the memorandum should be summarized in two pages. Note - If the borrower is a recently-formed single-purpose company, then elements 3, 4, and 5 will apply to the guarantors of completion and to the project sponsors. 3. The Borrower: This section is a brief biography of the borrower including such topics as date and state of incorporation, founder(s), lines of business, etc. 4. Capitalization: The borrower's current debt and equity position, including leases and trade debt, with amounts, terms, names, and addresses enumerated. Equity owners, and percentage ownership, should be identified. 5. Historical Financial Statements: If available, a minimum of five year's worth of complete historical financial statements

Jan 1, 1985

By N. W. Ratliff, P. J. Closmann

Production of oil by expansion from a cylindrical reservoir composed of two concentric regions of different properties has been determined as a function of time for a reservoir producing at constant terminal pressure. The parameters involved are permeability, porosity, compressibility and oil viscosity. Results agree with those of a generally accepted method for uniform reservoirs when all parameters are taken as uniform. Cumulative production at any given time is reduced below that of the uniform reservoir when a region of considerably lower permeability adjoins the well; cumulative production increases when a high-permeability region adjoins the well. Curves are presented illustrating quantitative effects of these variations. INTRODUCTION Most petroleum reservoirs can be exploited by release of pressure and consequent expansion of underground fluid. During part of the production history of certain reservoirs by this mechanism, fluid compressibility can be considered small and constant. Cumulative fluid produced by this means as a function of time was calculated for a uniform reservoir by van Everdingen and Hurst.l For certain cases where a production well has been damaged or where an acid treatment has been used, a zone of properties different from those of the reservoir may be created around the production well. In such a case, expansion of the reservoir fluid takes place in a system composed of two concentric cylindrica1 regions of different reservoir properties. Such composite systems were studied in connection with heat flow by Jaeger2 who presented a solution for temperature distribution in a radial system with an infinitely large outer radius. Similar heat flow problems have been studied by other authors Oil production from composite reservoirs was studied for constant production rate by Hurst,4 Loucks and Guerrero,5 and Carter.6 THEORY This work considers constant terminal pressure. Cumulative flow is calculated for a composite bounded system in which no flow takes place across the outer boundary (Fig. 1). Since the flow is considered to be purely radial, the problem involves only one space dimension and time. It is convenient to define the following dimen-sionless pressure drops (Fig. 1).

By Clyde E. Williams

Estimates indicate a life of known Lake Superior iron ore reserves of 20 to 30 years. Although some believe the future ore supply will come from foreign sources and will be brought to interior points via the projected Great Lakes-St. Lawrence waterway, and others fear a displacement of the interior steel-producing districts to the Atlantic seaboard, the author has faith that American engineering skill will make possible the use of lean ores from the Lake Superior district. Three general types of Lake Superior ores and ore formations, that represent possible reserves and require beneficiation, are: (1) the wash ores of the western Mesabi range, (2) the partly leached hematitic formations, and (3) the oxidized but largely unleached iron formations. The total tonnage represented by (1) and (2) is not large, but the recovery of iron from present washery tailings would bring on the market the equivalent of nearly one million tons of wash ore, annually. Group 3 comprises the magnetic iron formation of the eastern Mesabi range, the hematitic formations including the taconites of the Mesabi range, and the iron formations of all the other ranges. These formations represent our future supply of iron ore. Their treatment requires intensive research because the bulk of the iron oxide and silica minerals exist in a finely disseminated condition. The possibilities of the adaptation of tables, oil flotation, and other processes warrant extensive study. Cheaper method of agglomeration of the concentrate is essential. Recent developments in better preparation and sizing of blast-furnace charges indicate that substitution of agglomerated ore for fines will increase furnace efficiency and output. If agglomerated beneficiated ore can be shown to rate a per-unit premium for iron contents over the base rate or a premium for structure, the payment of these would greatly assist in enlarging our iron ore supply. Since present methods of taxation of ore reserves, which encourage the rapid depletion of rich ores, will result in using up our rich ores and later on putting domestic producers at a disadvantage in competing with' foreign producers, it would seem highly provident to conserve our rich ores and to increase the use of beneficiated ores as soon as possible.

Jan 1, 1931

By A. L. Engel

STRICTLY speaking, ore-dressing does not commence until after the ore is in the mill bins, but where complex ores are treated and their minerals separated to make the best commercial concentrate with the lowest economical tailing, ore-dressing problems begin and often center in the mine itself. This does not refer to the grade of the ore, but rather to the frequent condition in which metallurgical results radically different from customary are obtained because of changes in the character of the ore treated. Different varieties of ore can usually be identified as coming from well-defined depths or zones in the mine, or from known sections of the orebody. Varying degrees of alteration of the ore, inclusions of harmful gangue material, or variations in the quantities of component metallic minerals are often causes of temporarily bad metallurgical results in otherwise successfully operated plants, especially those employing differential flotation to. recover several valuable minerals contained in the ore.

Jan 1, 1931

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By J. H. Wiggins

This paper first pictures the economic phase of evaporation losses and the actual evaporative conditions in handling and storing crude and gasoline in the United States; then follows a discussion of some of the theories of physics involved in evaporation loss and lastly an application of these theories to handling oil and gas on producing properties. GRANTING that about 600,000,000 bbl. of light oil will be produced in the United States this year and taking the Bureau of Mines' statement that 7 1/2 per cent. of the total crude production will be lost before the finished gasoline is shipped from the refinery, the volumetric evaporation will be 45,000,000 bbl. of the cream of the gasoline. This is a conservative figure and is equivalent to 1,890,000,000 gal. The real value of this liquid is at least 150 per cent. of the value of an equal volume of motor fuel. At only 10 c. per gal., the value lost is $189,000,000; at 15 c. per gal. the loss is $283,000,000. If 750,000,000 bbl. of light and heavy oil are produced here this year and the average price per barrel is $1.333, the gross return to producers will be $1,000,000,000 and the net returns about $200,000,000, if the cost of production is only $1 per barrel. Thus, the evaporation bill is about 20 per cent. of the gross income and is equal to the net income of the crude-oil producers. Two other comparisons with popular phases of the petroleum industry will help give an adequate conception of the evaporation problem. These are: cost of preventing evaporation compared to cost of cracked gasoline and volume of gasoline evaporated compared to volume of gasoline manufactured from natural gas.

Jan 7, 1924

By Hallan N. Marsh, Bruce H. Robinson

It is generally believed that the flowing of wells through tubing instead of casing results in the conservation of gas. It is further believed that use of tubing prolongs the flowing life of a well and results in greater ultimate recovery, provided either that there are no adjacent wells, or that any adjacent wells are similarly operated. Recent experience in the flowing of Buckbee zone wells at Santa Fe Springs has not only substantiated both of these beliefs but has led to the further conclusion that the use of tubing results in a greater cumulative flowing production, ' even in a highly competitive field like Santa Fe Springs, where the wells concerned are closely offset by wells of both the same and other companies flowing through casing. Further, gas-oil ratio has been so reduced that greater ultimate recovery can be expected. In the belief that such would be the case, the majority of the Buckbee zone wells of one company were brought in through tubing, but enough wells were flowed through casing to form the basis for a comparison. For the purpose of this comparison, wells with flow strings 2½ or 3-in. dia. are designated as tubed wells, while those having flow strings larger than 3-in. dia. are designated as untubed wells. Casing used was mostly of 5 ¾-in. dia., the remainder being of 4¾-in. dia. There were 15 tubed wells and 8 untubed wells and they were scattered over the field in such a way that neither group appears to have any distinct advantage as regards location. Locations of all wells involved in the comparison are shown on Fig. 1. All the Buckbee sand wells of the company are included in the average production curves, with the exception of eight that were unsatisfactory for reasons other than the method of flowing. Findings 1. Buckbee sand wells flowing through casing larger than 3 in. had an average maximum production rate of 4670 bbl. per day, while wells flowed through straight tubing or 3-in. casing had an average maximum production of only 3300 bbl. per day. (See Fig. 2.)

Jan 1, 1932

By R. D. West

Miscible displacenzent recovers all oil in the area contacted by the injected .fluid, whereas water or immiscible gas drives usually leave substantial amounts of oil as residual. However, the Door mobility ratios associated with a gas-driven miscible displacement cause the sweep pattern efficiency to be much lower than that obtained with water flooding. One way in which the sweep eficiency in a miscible displacement process can be increased is by decreasing the mobility behind the flooding front. This can be achieved by injecting water along with the gas which drives the miscible slug. This water reduces the relative permeability to gas in this area and thus lowers the total mobility. The main operating conditions for the simultaneous injection -vrocess are that a zone of gas exists between the miscible slug and the leading edge of the water and that a su,@cient amount of gas be injected with the water to form the pas volume which is being left in the water zone. Laboratory model studies have shown that the ultimate sweep pattern efficiency can be as high as 90 per cent for a five-spot flooding system. If gar alone is used as the driving medium an ultimate sweep-out efficiency of about 60 per cent would be obtained in the same system. I INTRODUCTION The miscible displacement processes are a step towards total oil recovery. Conventional gas or water drives usually leave 25 to 5.0 per cent of the oil as residual in the swept portion of the reservoir. This residual can be eliminated if the oil is driven by a fluid with which it is miscible. At some reservoir conditions natural gas will become miscible with the oil. This is the "high pressure gas process".' More often, the oil does not contain enough light hydrocarbons to cause the gas to become miscible with the oil at reasonable pressures. In these cases a small band of fluid which is miscible both with the oil and gas must be kept between them2. Less than 2 per cent of the reservoir volume of the slug material is needed to keep the displacement miscible. Both processes work in the same manner, recovering all of the oil in the portion of the reservoir contacted by the injected fluids. The only difference is the manner in which the miscibility between the oil and the injected gas is obtained. Previous publications have contained detailed descriptions of these processes.1,2,3,4 However, total displacement of the oil in the swept region does not guarantee an efficient recovery process. The amount of oil to be recovered is also determined by the fraction of the reservoir contacted by the flood. This fraction is largely determined by the mobilities of the fluids. (The fluid mobility is the permeability of the rock to that fluid divided by the fluid's viscosity, k/p). This. dependence of the fraction swept on the mobility ratio has been shown in previous studies. Fig. 1 shows the ultimate fraction swept in a five-spot system as a function of the mobility ratio. The small drawings show the location of the areas left unswept for two different mobility ratios. The ultimate fraction of the reservoir swept is here considered to be attained when the producing stream contains less than 5 per cent oil at reservoir conditions. THE GAS-DRIVEN MISCIBLE DISPLACEMENT Since there is no oil left in the swept region after miscible displacement the mobility in this region is very high. It is often 50 times the mobility in the unswept regions. This means that the fraction of the reservoir contacted by the injected fluid will be less for a gas-driven miscible displacement than for a conventional water or gas drive. For a five-spot injection system, water would contact the entire reservoir volume, and the low pressure gas would contact about 90 per cent of this volume, while a gas-driven miscible displacement would only contact about 65 per cent of the reservoir. This poor sweep efficiency often offsets the benefits obtained through miscible displacement. Fig. 2 shows what the recovery curves for the three processes might look like for a five-spot system. The curves show the fraction of the in-place oil recovered as a function of reser-

By J. B. Clark

The oil industry has long recognized the need for increasing well productivity. To meet this need, a process is being developed whereby the producing formation permeability is increased by hydraulically fracturing the formation. The "Hydrafrac" process, as it is now being used, consists of two steps: (1) injecting a viscous liquid containing a granular material, such as sand for a propping agent, under high hydraulic pressure to fracture the formation; (2) causing the viscous liquid to change from a high to a low viscosity so that it may be readily displaced from the formation. To date the process has been used in 32 jobs on 23 wells in 7 fields, resulting in a sustained increase in production in 11 wells. INTRODUCTION Need For Process Although explosives, acidizing, and other methods have long been used, there still exists a need for artificial means of improving the productive ability of oil and gas wells, particularly for wells which produce from formations which do not react readily with acids. This paper discusses the development of a hydraulic fracturing process, "Hydrafrac", which shows distinct promise of increasing production rates from wells producing from any type of formation. The method is also considered applicable to gas and water injection wells, wells used for solution mining of salts and, with some modification, to water wells and sulphur wells. Requirements of Process In considering such a possible process, it appeared that certain requirements must be met. Some of these are as follows: A. The hydraulic fluid selected must be sufficiently viscous that it can be injected into the well at pressure high enough to cause fracturing. B. The hydraulic fluid should carry in suspension a propping agent, such as sand, so that once a fracture is formed, it will be prevented from closing off and the fracture created will remain to serve as a flow channel for oil and gas. C. The fluid should be an oily one rather than a water-base fluid, because the latter would be harmful to many formations. D. After the fracture is made, it is essential that the fracturing fluid be thin enough to flow hack out of the well and not stay in place and plug the crack which it has formed. E. Sufficient pump capacity must be available to inject the fluid faster than it will leak away into the porous rock formation. F. In many instances, formation packers must be used to confine the fracture to the desired level, and to obtain the advantages of multiple fracturing. Development of Process As a necessary step in the development of this process, it was deemed advisable to determine if the Hydrafrac fluids were actually fracturing the formation or whether these special fluids were merely leaking away into the surrounding formation. To determine this, a shallow well, 15 feet deep, was drilled into a hard sandstone. Casing was set, the plug drilled, and the well deepened in the conventional manner. A fracturing fluid dyed a bright red was used to break down the formation. Sand mixed with distinctively colored solids was injected into the well with the fracturing fluid to prop open any fracture made in the formation. A simulated gel breaker solution dyed a bright blue was then pumped into the well to determine if the gel breaker would follow the first solution. The results are shown in Figure 1. It was noted that a fracture was formed about the well bore, that the propping agent was transported back into the break, and that the breaker solution did actually follow the fracturing gel out into the fracture. While it is realized that this shallow well test is probably not exactly equivalent to a deep test, the results were interpreted as being a definite indication of what happens down the hole during a Hydrafrac job. Of interest in this connection is an investigation reported by S. T. Yuster and J. C. Calhoun, Jr.' This study, re~orted after the Hydrafrac work was under way, presents some excellent field data supporting the theory of fracturing a formation with hydraulic pressure. METHOD Steps of Hydrafrcu: Process Figure 2 shows a simplified cross-sectional view of a well treated by one version of the process. The first step, formation breakdown, is done with a viscous fluid, usually consisting of an oil such as crude oil or gasoline, to which has been added a bodying agent. Due to availability and price, war-surplus Napalm has been used in the majority of experiments to date. Napalm is the soap which was used in the war to make "jellied gasoline". The next step consists of breaking down the viscosity of the gel by injecting a gel-breaker solution and then after several hours, putting the well back on production. Figure 3 shows diagram-matically, a typical field hookup. The oil or gasoline is unloaded into the 10 bbl. tank shown on the left rear of the truck. This base fluid is picked up by the mixing pump and pumped through the jet mixer, where the granular soap is added. Next it goes into a small mixing tub, from which the high-pressure pump takes suction. The solution is then pumped into the well. The breaker solution is then taken from an extra tank and is displaced into the well immediately following the gel. When required, additional trucks may

Jan 1, 1949

By J. B. Clark

The oil industry has long recognized the need for increasing well productivity. To meet this need, a process is being developed whereby the producing formation permeability is increased by hydraulically fracturing the formation. The "Hydrafrac" process, as it is now being used, consists of two steps: (1) injecting a viscous liquid containing a granular material, such as sand for a propping agent, under high hydraulic pressure to fracture the formation; (2) causing the viscous liquid to change from a high to a low viscosity so that it may be readily displaced from the formation. To date the process has been used in 32 jobs on 23 wells in 7 fields, resulting in a sustained increase in production in 11 wells. INTRODUCTION Need For Process Although explosives, acidizing, and other methods have long been used, there still exists a need for artificial means of improving the productive ability of oil and gas wells, particularly for wells which produce from formations which do not react readily with acids. This paper discusses the development of a hydraulic fracturing process, "Hydrafrac", which shows distinct promise of increasing production rates from wells producing from any type of formation. The method is also considered applicable to gas and water injection wells, wells used for solution mining of salts and, with some modification, to water wells and sulphur wells. Requirements of Process In considering such a possible process, it appeared that certain requirements must be met. Some of these are as follows: A. The hydraulic fluid selected must be sufficiently viscous that it can be injected into the well at pressure high enough to cause fracturing. B. The hydraulic fluid should carry in suspension a propping agent, such as sand, so that once a fracture is formed, it will be prevented from closing off and the fracture created will remain to serve as a flow channel for oil and gas. C. The fluid should be an oily one rather than a water-base fluid, because the latter would be harmful to many formations. D. After the fracture is made, it is essential that the fracturing fluid be thin enough to flow hack out of the well and not stay in place and plug the crack which it has formed. E. Sufficient pump capacity must be available to inject the fluid faster than it will leak away into the porous rock formation. F. In many instances, formation packers must be used to confine the fracture to the desired level, and to obtain the advantages of multiple fracturing. Development of Process As a necessary step in the development of this process, it was deemed advisable to determine if the Hydrafrac fluids were actually fracturing the formation or whether these special fluids were merely leaking away into the surrounding formation. To determine this, a shallow well, 15 feet deep, was drilled into a hard sandstone. Casing was set, the plug drilled, and the well deepened in the conventional manner. A fracturing fluid dyed a bright red was used to break down the formation. Sand mixed with distinctively colored solids was injected into the well with the fracturing fluid to prop open any fracture made in the formation. A simulated gel breaker solution dyed a bright blue was then pumped into the well to determine if the gel breaker would follow the first solution. The results are shown in Figure 1. It was noted that a fracture was formed about the well bore, that the propping agent was transported back into the break, and that the breaker solution did actually follow the fracturing gel out into the fracture. While it is realized that this shallow well test is probably not exactly equivalent to a deep test, the results were interpreted as being a definite indication of what happens down the hole during a Hydrafrac job. Of interest in this connection is an investigation reported by S. T. Yuster and J. C. Calhoun, Jr.' This study, re~orted after the Hydrafrac work was under way, presents some excellent field data supporting the theory of fracturing a formation with hydraulic pressure. METHOD Steps of Hydrafrcu: Process Figure 2 shows a simplified cross-sectional view of a well treated by one version of the process. The first step, formation breakdown, is done with a viscous fluid, usually consisting of an oil such as crude oil or gasoline, to which has been added a bodying agent. Due to availability and price, war-surplus Napalm has been used in the majority of experiments to date. Napalm is the soap which was used in the war to make "jellied gasoline". The next step consists of breaking down the viscosity of the gel by injecting a gel-breaker solution and then after several hours, putting the well back on production. Figure 3 shows diagram-matically, a typical field hookup. The oil or gasoline is unloaded into the 10 bbl. tank shown on the left rear of the truck. This base fluid is picked up by the mixing pump and pumped through the jet mixer, where the granular soap is added. Next it goes into a small mixing tub, from which the high-pressure pump takes suction. The solution is then pumped into the well. The breaker solution is then taken from an extra tank and is displaced into the well immediately following the gel. When required, additional trucks may

Jan 1, 1949

By AIME AIME

MOTHER example of the broad field that is covered by the mining industry is the recent erection by the Phelps Dodge Corp. of a modern hospital building at Douglas, Ariz., and an identical one at the rejuvenated mining town of Morenci. Managers of even small mining properties are often called upon to build schools, houses, stores, maybe a jail, and provide sanitary arrangements, possibly the while acting as mayor of the town. Those who direct larger properties may have to build hospitals, as in the present instance, construct sewage disposal plants, and sometimes even build and manage railroads. A mining camp achieves its reputation among mining men not entirely by the grade or amount of its ore, or the skill of the operating staff in mining and milling it at a profit-the operation soon acquires a reputation as either a desirable or an undesirable place to live, regardless of its remoteness from what is euphemistically termed civilization. Such a community is indeed fortunate if it can boast of a good hospital.

Jan 1, 1940

By H. Fechtig, R. H. Buck, A. G. Guy

MULTIPHASE diffusion has been studied for many years in two-component systems1,2 and many of the experimental aspects are now fairly well understood.314 Although by no means all of the problems connected with the two-component case have been solved,' attention has recently been directed to the more complex situation involving three components. The pioneer work of Clark and Rhines6 yielded a qualitative picture of the types of behavior that can occur, and Clark7 has suggested conventions for describing the various phenomena. Kirkaldy and co-workers8,9 have made quantitative studies in several ternary systems and have offered explanations of the occurrence of isolated and nonisolated precipitates. At present, however, there is no comprehensive theory for the variety of phenomena observed in ternary, multiphase diffusion. By analogy with several studies that have been made of multiphase diffusion in the binary Cu-Zn system,2'10'11 a similar exploratory study was made of Cu-Zn-Ni alloys lying along the line in the ternary diagram from the point 80 Cu-20 Ni to the zinc corner of the diagram, Fig. 1. A principal question to be answered was whether initially plane interfaces would remain plane during the course of one-dimensional diffusion. The diffusion specimens studied are described in Table I. The five separate alloys from which they were made were melted in evacuated Vycor capsules from 99.9 pct purity copper, zinc, and nickel. Since some of the alloys were too brittle to be swaged, all of the alloys were used in the cast condition. To facilitate later homogenization, the molten alloys were solidified by plunging the capsule in water. Homogenization heat treatment was done at 720°C for 20 hr. The five nominal compositions in weight percent zinc and nickel, respectively, were: 37.5, 12.5; 44.0, 11.2; 50.0, 10.0; 55.0, 9.0; 65.0, 7.0. Ln Table I the alloys are identified only by their zinc content. Sandwich-type diffusion specimens were prepared by pressure welding disk specimens, each about 3 mm high by 10 mm in diameter. Welding was done in a special threaded vise which was heated at 500°C for about an hour in an atmosphere of flowing hydrogen. A measurement of the separation of the phase interfaces was made on a polished flat on the welded specimen, and then the specimen was sealed in an evacuated capsule and given the diffusion treatment shown in Table I. The diffused specimen was sectioned longitudinally

Jan 1, 1965

By Clarence P. Linville

In an article published in the Iron Trade Review,' I gave a convenient arrangement for the installation of wet and dry bulb thermometers for use in making moisture determinations in the air being blown into a blast furnace, and also gave a chart for use in obtaining moisture values from the thermometer readings. The data from which this chart was prepared were obtained from the tables in use by the U. S. Weather Bureau.2 The work of Carrier3 has shown that these tables are somewhat in error. He has recalculated the values for moisture as referred to wet and dry bulb thermometer readings, and he has prepared a psychrometric chart from the values thus obtained. This work has placed the subject of psychrometry upon a correct scientific basis. I think it is proper that we should recognize the importance of his work and give him credit for one of the most interesting and valuable researches that have been published in recent years. Blast-furnace men are not ready to use, as he suggests14 a value expressed in grains of water accompanying a pound of dry air. However convenient this may be for heating and ventilating work and other engineering problems, there are several reasons for preferring the use of a value expressed in grains of water in a cubic foot of mixed air and water vapor, in connection with combustion phenomena and the effects of moisture on blast-furnace operation. Previous papers presented to the Institute have used such values and we have

Jan 1, 1914

By Nicholas J. Grant, Henry Epstein, John Chipman

FOR many years steel producers have been concerned with the presence of hydrogen in steel. Hydrogen dissolved in excess of its solid solubility at the melting point may cause bleeding and gross unsoundness in ingots and castings. In fully-killed steels the hydrogen content which results in these difficulties varies with the alloy content1 and may range from 6 to 12 ppm.* It is also recognized that of heat treatment diminishes rapidly as the size of the part to be treated increases. The time required to remove a specified fraction of the hydrogen present increases as the square of the diameter of the section, making the treatment of large- sizes impractical. In order to prevent bleeding and gross unsound-ness due to hydrogen, and in view of the inadequacy of corrective heat treatment alone to provide optimum properties when hydrogen is present in large sections, efforts to limit the hydrogen content must be taken while the steel is still liquid. The main subject of this paper is a discussion of the factors affecting the hydrogen content of liquid steel in acid and basic open hearth, and basic electric two-slag furnace processing. Literature Survey Because many of the results and observations reported in the literature have a direct bearing on the results obtained in the present research and form part of the basis for conclusions reached, a brief summary of the findings is necessary. Methods for experimental investigation of hydrogen in liquid steel are comparatively new. The first attempts to estimate the hydrogen content of the open hearth bath were by Kalling and Rudberg,6 who devised a method for collecting gases evolved from the boiling bath of a basic open hearth furnace. They found that the gas during the boil generally contained 2 to 3 pct H2. From this and Sieverts'

Jan 1, 1958

By B. R. Palmer, M. C. Fuerstenau

Oxide and silicates respond to flotation with a large number of anionic collectors. These include carboxylates (fatty acids), sulfonates, alkyl sulfates, and certain chelating agents. In contrast to sulfide mineral flotation, relatively long-chained collectors (generally longer than 10 carbons) are required to effect flotation of this group of minerals. The structural formulas of these various anionic collectors are presented in Table 1. Formulas and solubilities of various fatty acids are presented in Table 2. These solubilities are those of the dissolved and undissociated species of the acid, e.g. oleic acid, HOl(aq). Of the compounds listed, oleic acid and abietic acid, which IS a major constituent of talloel, are used most commonly in commercial applications. The usage of these two collectors is related to cost and effectiveness. In addition to their high molecular weights, oleic acid contains a double bond in its hydrocarbon chain, while abietic acid is comprised of aromatic rings containing double bonds. The presence of double bonds increases solubility significantly over that of saturated homologues. Stability of metal-collectors assumes a most significant role in these systems, and the solubility products of various metal carboxylates and sulfonates are listed in Tables 3, 4 and 5. In addition to these properties, strength of the acids of these various anionic collectors is also important. The carboxylic and hydroxamic acids are weak acids whereas sulfonic and alkyl sulfuric acids are strong acids. All of the carboxylic acids fall in the range of pK = 4.7 ± 0.5 ([2]); the pK of hydroxamic acid is around 9 ([3]); and the pK of sulfonic acid is about 1.5 ([4]).

Jan 1, 1976

By John W. Chang

Introduction Automatic control of primary ball mill circuits has received much attention over the past decade, primarily because its advantages ultimately can be translated into economic terms. Apart from such obvious benefits as improved product quality, increased throughput, and more stable operation, less direct benefits such as easier operation, more orderly maintenance scheduling, and timely management reports all can be realized with the application of modern automatic process control equipment and techniques. Software configurable digital computer-based control systems offer ease of change in control strategies. Occasional control strategy changes are necessary whenever control objectives change or circuit modifications occur. The dependency of control strategies on control objectives and circuit equipment to effect optimal circuit operation is an important, but often neglected issue. Because of the potential for even better control, research and development work continues. [See (Ulsoy & Sastry, 1981) and (Hulbert & Braae, 1981).] Some of the possibilities are discussed later in this presentation. A few preliminary remarks may be in order concerning the relationships among control objectives, control strategies, and circuit equipment. Generally accepted control objectives for primary ball mill circuits include: 1. Maintaining a desired percent solids in the mill. 2. Maintaining a desired measure of particle size distribution at the cyclone overflow. 3. Maximizing throughput. Control Objective I is a requirement for proper operation of the ball mill, especially if it is a grate mill. It concerns smooth movement of material through the mill. Control Objective 2 is a product specification - one of the requirements for proper flotation operation. Control Objective 3, an expression of the desire to get the most out of the circuit, is the easiest to evaluate in economic terms. It assumes that the processes downstream

Jan 1, 1982

By Elwood G. Haney, R. N. Parkins

Stress corrosion cracking of two heats of 18 pct Ni maraging steel in rod form immersed in an aqueous solution of 0.6N NaCl at pH 2.2 has been studied on un-notched specimens stressed in a hard tensilf machite. Austenitizing temperature in the range 1830 to 1400 F has been shown to have a marked influence on the propensity to crack, the loulest austenitizing- temperature producing the greatest resistance to failure. In the nzosl susceptible conditions, the cracks followed the original austenile grain boundaries; but when tlze steels zcere heal treated to inproze their resistance to stress corrosion, the cracks becatne appreciably less branched and slzouqed significant tendencies to become trans granular. Electron metallography of the steels indicated the presence of snzall particles, possibly of titanium carbide, along- the prior austenite grain boundaries and these particles u:ere more readily detectable in the structures that were most susceptible to cracking. Crack propagation rates, which appeared to be dependent upon applied stress and structure, were usually in tlze reg-ion of 0.5 mm per hr and may, therefore, be e.xplained on tlze basis of a purely electrochetnical ,nechanism. However, there is some ezliderzce from fractography that crack extension may be assisted by ttlechanical processes. Anodic stit)zulation reduced the tiwe to fracture, although cathodic currents of small magnitudes delayed cracking-; further increase in cathodic current resulted in a sharp drop i,n fracture litne, possibly due to the onset of hydrogen ewbrittlement. THE use of the high strength maraging steels, with their attractive fracture toughness characteristics, is restricted because of their susceptibility to stress corrosion cracking in chloride solutions. Although this limitation has resulted in investigations of the stress corrosion susceptibilities of these steels, there have been few systematic studies aimed at defining the various parameters that determine the level of susceptibility. It is the case that the usual tests have been performed with the object of defining some stress or time limit, on unnotched or precracked specimens, within which failure was not observed,' but while such results may be of some use in design considerations, they are necessarily concerned only with the steels as they currently exist and not with their improvement to render them more resistant to stress corrosion failure. This omission may be considered unfortunate because the indications are that stress corrosion in maraging steels shows dependence on structure in following an intergranular path, and since experience with other systems of intergranular stress corrosion crack- ing is that susceptibility may be varied by modifying heat treatments, a similar effect may be expected with maraging steels. It is sometimes from such observations that a fuller understanding of the mechanism of stress corrosion crack propagation begins to emerge, leading in time to the development of more resistant grades of material. The present work was undertaken to study only one aspect of the influence of heat treatment upon the cracking propensities of the 18 pct Ni maraging steel, namely the effect of austenitizing temperature, although certain ancillary measurements and experiments have been undertaken. EXPERIMENTAL TECHNIQUES Most of the measurements were made on a steel, A, having the analysis shown below, although a few results were obtained on a steel, B, having a slightly different composition. Both steels were supplied in the austenitized condition, A as 3/8-in-diam rod and B as 1/2-in.-diam rod. Cylindrical tensile test pieces were machined from the rods: the overal length was 2 1/2 in., the gage length 1 in. and the diameter 0.128 to 0.136 in. The stress corrosion tests were carried out with the specimens strained in tension in a hard beam testing machine, the necessary total strain being applied to the specimen over a period of about 30 sec, after which the moving crosshead was locked in position and the load allowed to relax as crack propagation proceeded; the load relaxation was recorded. The load was applied after the specimen had been brought into contact with the corrosive solution, the latter being contained in a polyethylene dish having a central hole through which the specimen passed, leakage being prevented by the application of a film of rubber cement. The specimen was in contact with the solution for over half of its gage length and the solution was exposed to the air during testing. The solution was prepared from distilled and deionized water to which NaCl was added, 0.6N, and the pH adjusted to 2.2 by HCl additions. The composition of the solution

Jan 1, 1969

By Tom W. Pfeifle, Paul E. Senseny

INTRODUCTION Engineered structures such as mines, shafts and tunnels, and storage caverns for hydrocarbons, chemical s and brine are being built in natural rock salt formations in increasing numbers. In addition, salt formations are being considered as potential hosts for mined, nuclear waste repositories. The popularity of these formations for engineering purposes stems from the many favorable commercial, physical, and thermal characteristics attributed to the material itself. Not only have the formations been stable and free of dissolution for hundreds of millions of years, but the salt is fairly easily mined and has very low permeability, low water content, and high thermal conductivity. Another characteristic of salt is its tendency to flow or creep when subjected to a shear stress. Although this behavior may be desirable in certain instances, it may be detrimental in other instances since the creep rate may be large enough to produce deformations that tend to reduce the volume of storage caverns or to restrict access to mining operations. In either case, the engineer is faced with the problem of accurately predicting the long-term structural deformations under various combinations of stress and temperature and is required to compare these deformations with long-term design criteria. In the laboratory, deformation-versus-time curves obtained at constant stress and temperature show that creep of salt is similar to creep of many other crystal line solids. Figure 1 shows a typical deformation-versus-time curve for salt. When a shear stress is first applied, the rate of deformation is high, but decreases monotonically. This initial behavior is called transient or primary creep. At some time, the deformation rate no longer decreases but continues at a constant rate. This behavior is called steady-state

Jan 1, 1982

By William E. Ford, Edward Salisbury Dana

1. Normal Class (28) Gypsum Type 2. Hemimorphic Class (29) Tartaric Acid Type 3. Clinohedral Class (30) Clinohedrite Type Mathematical Relations of the Monoclinic System Crystallographic Axes. - The monoetinic system includes all the forms which are referred to three unequal axes, having one of their axial inclinations oblique. The axes are designated as follows : the inclined or clino-axis is a; the ortho-axis is b, the vertical axis is c. The acute angle between the axes a and c is represented by the letter 0; the angles between a and b and b and c are right angles. See Fig. 331.

Jan 1, 1922

By J. F. Myers, F. M. Lewis

DISCUSSION L. E. Djingheuzian (Canadian Dept. of Mines and Technical Surveys, Ottawa)—In their Summary the authors say: "Reconciling the grinding efficiency with good metallurgy is still a problem." In the discussion of the first paper8 in his reply to W. I. Garms, Mr. Myers states: "Our grinding process with smooth I-in. balls has reduced by nearly one half the metallic losses in the fine micron sizes of the tailing. This is simply because less of the fine micron sizes are produced. Since the + 65 mesh size is the same as formerly, a higher percentage of the intermediate sizes are developed. These sizes have the highest floatability, require the least reagents, and use less floating time. "These factors contribute so heavily to the overall economies that dropping our power grinding gain from 28 pct back to 19 pct is a small detail. However, we feel that this is only a momentary situation and that eventually the best features of the grinding and flotation processes can be brought together, which is as it should be." Italics are mine. The above statements, to me, appear to be the answer to the opening statement in the Summary. Denoting the costs at different power grinding gains as: Power Grinding Power Grinding Gain, 28 Pct Gala, 19 Pct Cost of grinding G G1 Cost of flotation F F1 Value of metallic losses T T1 where G1 > G2 F3 < F, and T1 < T, we have: G1+Fl+T1<G +F+T. Since the authors accept the idea that "grinding in flotation plants becomes part of the &apos;conditioning&apos; of the feed to flotation",4 i.e., that in flotation the ball mill is primarily a conditioning machine, it can be postulated that Tennessee Copper grinding at cost G1 is more efficient than grinding at lower cost G. This can be directly inferred from the Conclusion of the paper. Mr. Myers also emphasizes this at the end of his reply to Mr. Garms: "that grinding is for the purpose of preparing flotation feed and not grinding per se." This, to me, in the final analysis means that when the efficiency of grinding is weighted against the conditioning factor, the former becomes a function of efficient conditioning, hence, within the system in which proper conditioning is the dominant factor, the best grinding efficiency is provided by grinding which will contribute towards the optimum conditioning. This brings us again to the statement: "that if every grinding unit were considered as a conditioner for each following step, efficient grinding plants would become much easier to design."&apos; In other words, grinding equipment should be balanced against the flotation equipment and against chemical reactions taking place in the system. F. C. Bond (Allis-Chalmers Mfg. Co., Milwaukee)— The authors&apos; discussion of the probable ball motion in a slow speed high dilution mill is very interesting. When the 1-in. balls have worn down to about one fourth of their original weight they apparently first develop a flat surface; as wear progresses this flat face becomes concave, and other concave faces appear. It seems more probable that the first flat face may form at the softest part of the ball surface, and that each succeeding contact tends to force this flat face into sliding contact with a larger round ball; than that the flat faced ball tends to pair off with a particular round ball and to travel with it continuously. When the small worn ball has a flat face and is in sliding contact with a large round ball, the surrounding large balls will assume a more or less definite pattern, and slide against the worn ball, thus producing secondary concave faces. The primary concave face seems to be larger and better developed than the secondary faces. The ball charge can be divided into "concaves" which show at least one concave surface, "intermediates" which have developed flats or incipient concaves, and "rounds." Ball slippage is always present in a tumbling mill, and the mutual ball movement is necessarily a combination of rolling and sliding. The sliding motion is apparently concentrated upon the smaller worn balls which nest between the surrounding larger round balls. When each worn ball starts its upward path in the mill its primary flat or concave surface fits against a larger round ball, and the round ball slides upon it. The action may be something like that of the ball separator in a ball bearing, except that the worn sliding balls are always under considerable pressure. The material is ground under the combined influence of breakage 1—by impacts between falling balls and between falling and supported balls, 2—by being nipped between rolling balls, and 3—by being rubbed between the sliding balls. The rubbing action will be increased in the presence of worn balls with concave surfaces. The rubbing action probably produces a considerable portion of the finely ground slimes in the product. The worn balls commonly approach tetrahedrons in shape, and are very different from concavex, each of which has two equal opposed concave surfaces. Concavex were designed only to grind upon themselves, and not for use in combination with grinding balls. Their action in a grinding charge is very different from

Jan 1, 1952