Search Documents

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere' that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic location or seam characteristics modem raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality and these objectives may be sought by commencing the preparation of coal underground at the "working face." Underground preparation involves choosing those portions of the bed which can be cleaned to satisfy predetermined market requirements involving (1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1) seam under development, (2) mining equipment available and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another the (1) petrography of the coal in the bed does not re- main uniform, (2) character of roof and floor are subject to change and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content and petrography are of considerable interest and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal. The prospecting and evaluation of any area containing one or more salable coal beds by means of channel samples taken from outcrop openings and/or from diamond-drill cores can yield valuable data on coal characteristics. By correlating the data developed from distinct petrographic sections of channel and/or drill core samples, the quality of the bed according to stratification will be evident. There are few coal beds that do not show wide variations of such characteristics as ash and sulfur

Jan 1, 1968

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By Dirk A. Benham, William A. Warfield

INTRODUCTION Whenever a mine operator is faced with a decision between various mining methods or even equipment selection, he must be assured that his decision will have a positive effect on his economic operating goals. For instance, if a mine operator has a choice of using an LHD mining system or a slusher mining system, then his decision to use either must not only fit within the operational limitations of the mining plan (such as production requirements, physical features of the ore body, mine plant facilities, manpower requirements, etc.), but also assure that the ore is being extracted at the least possible cost. To aid in his decision making process, the operator will commonly compare acquisition costs, operating costs, maintenance costs, and the operational advantages and disadvantages of each system in addition to considering his personal observations and feelings. A decision to select a mining system using only those criteria aforementioned will not necessarily lead the operator down the path to maximizing profits. In addition, the operator should also compare the economic effects of each system upon the overall mining operation. A relatively simple method for determining the economic effects is to calculate and compare the break-even grades for each system under consideration. By implementing such an analysis, the operator can now select a mining system which can operate within the limits of the mining plan as well as extract the ores at the least possible cost, thus yielding maximum profits. This paper will present the geologic and physical conditions of a mine being operated by the Hypothetical Mining Company in the Grants Mineral District. An LHD and Blusher mining system are under consideration and are compared by examining operating costs, equipment availability, and the conventional operational advantages and disadvantages of each. Finally, the economic effects of each system upon the overall mine's operation are compared by utilizing break-even grade analysis. DESCRIPTION AND MINING METHODS The Hypothetical Mining Company has located an ore body in the Grants Mineral District. After extensive surface exploration drilling and cost considerations are evaluated, it is decided to open a mine. The following tasks must now be performed: 1. outline ore body and it's basic characteristics, 2. look at mining methods currently in use in the area, and 3. determine mining techniques and methods for exploitation of the ore body. For the sake of argument, the newly discovered ore body is located towards the western edge of the Grants Mineral Belt. The host rock for uranium mineralization is the Westwater Member of the Morrison Formation. The Westwater Canyon sands are overlain by the Brushy Basin Member of the Morrison Formation and underlain by the Recapture Member, all of Jurassic Age. Westwater Canyon sandstone is a fine to very course grained subarkosic sand with interbedded green and red mudstone. The Brushy Basin Member consists predominantly of greenish-gray mudstones and contains thin lenses of sandstone and a few thin beds of limestone. The Recapture Member consists of alternating thin beds of reddish brown, grayish red, and light gray sandstone and siltstone. The Recapture interfingers with the Cowsprings Sandstone in the area of the mine. The mineralization is based on the groundwater flow within the Morrison Formation. Primary ore distribution is based on three basic parameters: ore migration in a geochemical cell, lenticular mudstone interbedding, and enrichment along fault zones. In areas where two fault systems intersect, ore thicknesses of up to 30 m (100 ft.) are encountered. In those areas where the ore is well defined and thicknesses facilitate full face mining, the mining methods are determined more by ground or operating conditions, equipment availability, and access to working areas than they are in the fringe areas of the ore body where grade control is more important and split-shooting and break-even grade determines the mining technique. If a modified room-and-pillar mining method using systematic development is selected, better control of the ventilation, equipment utilization, and mining plan can be obtained. Figure I shows a typical mining area where the ore is thick,

Jan 1, 1982

By W. D. Robertson, D. A. Koss, A. J. Goldman

THE significance of the hcp (E) structure, which appears when Fe-Cr-Ni alloys (stainless steels) are transformed martensitically, has been the subject of considerable study and speculation.'-7 It has been proposed that the hcp structure is an intermediate phase in the transformation: fcc (austenite) — hcp (E) -bcc (0, martensite). However, recent studies by transmission electron microscopy6,7 have indicated that the hcp structure may be a consequence of the large shear strain (10 deg) associated with the fcc to bcc transformation. That is, the transformation to a bcc structure is accompanied by extensive dissociation of dislocations in the parent austenite, which has a low stacking-fault energy.'-'' X-ray diffraction analysis of the transformed alloy reveals a pattern of lines corresponding to an hcp structure, together with the parent austenite and the bcc product. The fact that the hcp structure is observed only in association with the bcc product in these alloys1'4'6'7 lends support to the conclusion that the hcp structure is a secondary product of the transformation. But, the evidence is circumstantial and more definite resolution of the two possibilities mains to be obtained. If the hcp structure is an intermediate product of the transformation, as in 1) above, then two distinct Ms temperatures should be observed, Ms and To evaluate this possibility, three different techniques that are particularly sensitive to the structural changes accompanying such transformations have been used in an attempt to detect two transformation temperatures in an Fe-15.1 Cr-11.7 Ni alloy: 1) high-sensitivity differential thermal analysis, 2) the temperature dependence of resonant frequency (elastic moduli), and 3) internal friction of cylindrical specimens vibrating in either longitudinal or torsional modes. To obtain the necessary sensitivity, a differential thermal analysis technique was developed for the purpose, Fig. 1. The differential temperature between a nickel standard and the specimen was amplified to produce a sensitivity of 0.02OC (0.7 v) in temperature difference. The specimen and the standard were surrounded by a copper block and the entire assembly was immersed in a solution of methyl and ethyl alcohol, freezing point, - 140OC, which provided the necessary thermal stability to reduce temperature fluctuations to negligible proportions. A cooling rate of about 1.5OC per min was obtained by bubbling liquid nitrogen through the liquid bath. In order to calibrate the experiment with respect to the evolution of heat in the transformation from fcc to hcp structures, differential cooling curves were obtained for an Fe-19.8 Mn alloy, which transforms martensitically to E.'"-' a Ms(e) temperature of 145°C was clearly defined by a temperature

Jan 1, 1964

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

By J. Winlock

To have been chosen by you to give the Howe Memorial Lecture is the greatest honor I have ever had and I should like to have you know that I appreciate it deeply. Many years ago I had the privilege and the pleasure of working with Professor Howe in the private laboratory which he had established in his home at Bedford Hills, New York. Without doubt he was one of the world's greatest metallurgists and so you can imagine what a difficult task it has been for me to live up to his teachings. Every morning Professor Howe would outline the work he wanted done and the recollections of those conferences are clear to me to this day. Sometimes he would ask me to ride in his automobile and the chauffeur had full instructions to go no more than fifteen miles an hour. If he did so, Professor Howe was sure to rap upon the man's shoulder with his cane. I assure you, however, Professor Howe's thinking was not at that rate. His homely advice, his patience and his perfect control of the English language still impress me. Many times I heard him dictate a complicated paper on metallurgy and never find it necessary to change a single word. There are no better words to describe the character of Professor Howe, in my opinion, than those used by Professor Sauveur when he presented the John Fritz Medal to him in 1917: "Lover of justice and humanity Public servant and public benefactor, Master of the English Language, Loyal and devoted friend, Untiring and unselfish worker in an important field of science." I hope you will bear with me with the same patience and understanding which he used to give to me. The peculiar behavior of steel at the yield point has long been known and has been the subject of much research, both in this country and abroad.',' Many theories, including some of mine and my colleagues, have been suggested, but none of them, in our opinion, fully explains to our satisfaction why the phenomena occur. Of particular importance has been the work of Nadai,3 Siebel and Pomp,' Sachs and Fiek,5 Rawdon,0 Kenyon and Burns,' Gensamer," Gensamer and Meh1,0 Davenport and Bain,'" Fell," Deutler,12 Brinkman,13 MacGregor,14 Hollomon,15 Cot-trell,16 and Palm." The question of what is occurring during this singular behavior is not only of interest from an academic point of view, but is of great practical importance for at least two reasons: 1—The highly localized plastic flow which occurs during the deep drawing of light-gage steel gives rise to surface markings which seriously mar its appearance, Fig. 1. If the forces causing the deformation are primarily tensile forces, these surface markings occur as depressions in the surface. Whereas, if the forces causing the deformation are primarily compressive, irregular lines of elevations occur. These surface markings are known as Luder's lines, Hartmann lines, the Piobert affect, and, in the shop, as "stretcher strains." 2—The steel is in the most suitable condition for deep drawing after the yield point phenomena have been removed. When this is done, the steel may be deep drawn more easily and to a greater extent.' It should be mentioned that steel is not the only metal which shows this peculiar behavior at the yield point. Stretcher strains occur, also, during the deformation of some copper-nickel-zinc alloys." The purpose of this paper is not an attempt to describe what causes the steel to behave in this peculiar manner, but an attempt: l—to describe what is taking place at the yield point; and 2—to show the influence of the rate of deformation on the tensile properties of some plain carbon steels. As is well-known, there are two methods of deforming a metal in tension: 1—by actually hanging an increasing amount of dead weight on the metal; or 2—by deforming the metal at some given rate or rates by means of oil pressure cylinders, screws, etc. With the first method, the load is always present and, clearly, no drop in load can ever occur while the steel is deforming. With the second method, the registered load is the resistance of the steel to the deformation being imposed upon it. The second method is the one most widely used, and is the one referred to throughout this paper. In order to describe clearly what is occurring at the yield point in steel, it will help, I believe, if a description is first given of what occurs when alumi-

Jan 1, 1954

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By Rex B. McLellan, W. A. Oates

FROM a consideration of the application of the Gibbs-Duhem equation to multicomponent systems arken&apos; derived the following equation applying to dilute solutions of a solute, 2, dissolved in a binary solution, 1-3:

Jan 1, 1969

By C. Chiou, M. E. Fine

While Gunier-Preston zones are growing in Al-4.2 pct Cu at room temperature, Young&apos;s modulus, measured dynamically, increases about 0.4 pct. From the change in modulus with time the exponent of time in the rate equation for growth of the zones was deduced to be %. From a comparison of the rates of increase of modulus at 1, 28, and 42°C an activation energy of 12 to 14 Kcal per mole is computed. These findings support the idea that copper atoms are supplied along dislocation channels to growing zones. In alloys the elastic constants will be functions of the distributions of the atoms. If the degree of ordering or clustering is changed, one expects a corresponding change in the elastic constants. During age-hardening of aluminum-copper alloys at room temperature, the copper atoms cluster on 100-type planes in the aluminum lattice forming

Jan 1, 1959

By Strathmore R. B. Cooke, Iwao Iwasaki

RECENTLY spectrophotometry has been reported to provide a convenient technique for the rapid and reproducible determination of xanthate concentration in pulp solution 1,2 and for a kinetic study of xanthate decomposition in acid solutions." Since the application of this analytical technique is feasible for those compounds showing pronounced light absorption maxima in the near ultraviolet region, it was deemed advisable to investigate the absorption spectra of some of the organic compounds that are used in flotation. It is known empirically that certain groups of atoms in an organic compound cause characteristic light absorption in the ultraviolet and near ultraviolet range, and the wavelengths and intensities of the corresponding absorption maxima are relatively independent of the nature of the remainder of the compound. The characteristic values of such groups, which are known as chromophores, are given in the literature. 4,5 According to this information, many of the sulphydryl compounds are expected to show absorption maxima in the near or long wavelength ultraviolet region, whereas the saturated fatty acids and the saturated alkylamines do not.

Jan 11, 1957

By Henry F. Heblby

HOW often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days1&apos; indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer&apos;s day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. The Sources of Atmospheric PolLution The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is prob- ably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominantly dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh Indicative of the stupendous quantities of fuel that are employed in this industrial area&apos;s economy, the following (Table I) taken from the U. S. Census (1940) may be of interest. In tonnage consumed in the area, the figures are equally impressive: Annual Tons oF Coal Metallurgical Industries.... 35,000,000 to 40,000,000 Commercial Installations (Pgh.)................. 1,500,000 Domestic hand-fired) (Pgh.)................. 750,000 An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, uti-mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1949

By W. H. Schacht

In the Lake Superior District, the air indoors must be heated continuously during eight months of the year and occasionally during the remaining months. Incident with mining in this district, therefor?, there is need for heating many of the buildings connected with these operations. In addition to the mine buildings, that is, shops, engine houses, offices, change houses, etc., such public buildings as schools, library, and theater, when close to the mines, are often supplied from the mine heating mains. At the Copper Range Company&apos;s mines, Champion, Trimountain and Baltic, the heating surface thus supplied from the mine mains is over 50,000 sq. ft. (4645 sq. m.) which requires a steam consumption, at times, of 18,000 Ib. (8165 kg.) per hour, or the equivalent of a rate of ovcr 50 tons of coal per day (were live steam used). This figure is based on a consumption of 1/3 Ib. per sq. ft. of heating surface during the coldest weather, and provided the system is not wasting steam by blowing it to the atmosphere or into the return line on account of leaky traps, which so often is the case. Under the latter conditions, steam consumptions of three to four times the above rate are not uncommon. This shows that the cost of heating is of enough importance to he given serious consideration, especially at this time of rising prices of fuel. The power and heating value of exhaust steam arc appreciated by most engineers, and its application for such purposes is general. At our stamp mills, the exhaust from the stamps is used to operate low-pressure turbines, thus reducing the former water rate per horsepower developed by more than 50 per cent. At the above-mentioned mines, electric motors have replaced the many small steam engines, so that this supply of exhaust steam has been practically eliminated. The larger engines are compound, triple, or quadruple condensing. The hoists, however, in all cases are simple and non-condensing and of two sizes, namely, 24 by 60 in. and 32 by 72 in. (61 by 152 cm. and 81 by 183 cm.). These hoists now offer the only available supply of exhaust steam; but as this flow is intermittent and varies from extreme violence to zero, the steam so discharged cannot be

Jan 1, 1922

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966

By J. H. Berryman

THE use of oxygen as a bath reagent in hearth furnaces during the refining period is a familiar story. Investigations and tests in which oxygen was substituted for iron ore to reduce carbon date back 25 years and include the work of Bigge,1 Browne,2 and Chelius.3 During this past year the majority of the experimental work in the use of oxygen was carried on mainly in open-hearth shops, since it was felt that the greater field for application lay in this type of furnace. Much constructive work was done in evaluating the carbon-oxygen relationships, as reported by Slottman and Lounsberry4 and by Hughes.5 Steelmakers using the electric furnace have been actively engaged meanwhile in an experimental program of their own, with such success that the oxygen injection pipe has become a tool in the day to day production of low-carbon and stainless steels.

Jan 1, 1947

By J. H. Swisher

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs&apos; absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By Henry S. Burnholz, Charles Y. Clayton, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. &apos;Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months&apos; survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By Charles Y. Clayton, Henry S. Burnholz, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. &apos;Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months&apos; survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By E. J. KENNEDY

FEBRUARY 15-18 will be the outstanding dates of the month for members of the A. I. M. E., for then the 141st Meeting of the Institute is to be held in the Engineering Societies Building, at New York. What with 41 technical sessions, the Annual Business Meeting at 4 o&apos;clock Tuesday afternoon,, two sessions of the Section and Division delegates, minor committee meetings, and the many luncheons and dinners, the Dinner-Smoker, Informal Dance, President&apos;s Reception and the Dinner-Dance, the opportunity will be limited to do- more-than cast sheep&apos;s eyes at New York&apos;s other multitudinous attrac¬tions until the meeting is over. The technical program is diverse but well organized. The sessions are almost equally divided among the four days, with ten on Monday, Tuesday, and Wednesday, and 11 on Thursday. The meeting opens Monday morning with registration. Be sure to attend to this detail. Failure to do so may have its repercussions at the meeting and throughout the year.

Jan 1, 1932

By L. H. E. Weyher

As a result of past developments, mainly at universities, the coal industry has had access for a decade or more to a number of computer programs for coal mine planning. Using some of these programs Bethlehem Steel&apos;s Research Department in 1969 launched jointly with Bethlehem Mines Corporation an extensive research and development program aimed at: (1) testing the capabilities of these programs through trial applications as the need and opportunity existed, (2) defining what additional capabilities were required to make mine planning computer systems fully useful in the hands of Bethlehem&apos;s mine-planning engineers in the field, and (3) developing and implementing in the field the mine-planning systems agreed on. This program is now nearing completion, and several of Bethlehem&apos;s operations routinely use the planning tools that were developed. The progress of this research program is discussed in terms of our initial trial applications of computer methods to mine planning and the incorporation of several innovative features into our new set of computer programs, in particular, the use of time sharing, data base management systems, and general-purpose simulation languages.

Jan 1, 1977