Search Documents

By V. W. Buys, R. E. Havener

11.3-1. Basic Principles. Communications systems available for application to surface mining operations can be divided into basic categories. These are: 1. Wired systems requiring some type of metallic conductor 2. Nonwired systems, or those commonly referred to as space-radio systems. Under the heading of wired systems, telephones of the ringer type utilizing magnetos were used in the early pit operations. These are still being used in underground mining operations where calling is accomplished by ringing a code made up of short and long rings. While the standard Bell Telephone Systems have not been applied extensively in underground mining, they have been used in open pit operations but have the disadvantage of using multiple pair cables which must be installed and maintained as the mining operations proceed. They have the advantage however, that when a Bell System is installed in a surface mining operation, communication is available not only within the operation but to any point in the world through the facilities of the world-wide Bell Systems. A second type of communication available is the audio system or public address system requiring the use of a special audio cable made up of shielded pairs for the loudspeaker and microphone circuits. Audio systems have one outstanding advantage over most telephone systems in that, with a high-powered amplifier, a paging call can be heard over and above the high ambient noise conditions usually found at a surface mining operation. However, they have the disadvantage of requiring special cable which must be installed and maintained. Another type of wired communication system available for surface mining is that of carrier frequency equipment similar to that used in underground mining operations. In this system, transmission is accomplished by means of a frequency modulated carrier that travels over the underground trolley wire, the rail on which locomotives travel, and adjacent telephone wires.

Jan 1, 1968

By Hans Lundberg

BASED upon an instrumental improvement, a new development has taken place in the art of electrical prospecting, and some remarkable results have already been obtained with regard to potential exploration. In order to visualize the importance of this development, it is deemed advisable to review briefly the fundamental facts about potential surveys. Potential exploration may be carried out qualitatively or quantitatively. Qualitative investigations are made by determining and plotting on a map points of equal potential, whereby any anomalies are revealed, without, however, much clue to their magnitude. Quantitative investigations determine the variations of potential or potential drop, and thus show not only the location of the anomalies, but also their magnitude. Figs. 1 to 6 illustrate the influence of simple types of ground inhomo-geneities, assuming one effective exciter potential only. Such a condition can be closely realized by connecting an electric current source to two electrodes, one of which, is located at a great distance. Assuming uniform ground resistivity, the resultant potential distribution may be represented by concentric spheres. Any change from the normal condition causes a characteristic distortion of the spheres, which becomes different for different types of resistivity variation. The series of Figs. la to 6a illustrates schematically results of qualitative investigations and series 1b to 6b results of quantitative investigations. Figs. 1 and 2 picture the well-known case of local resistivity variations normally encountered in ore prospecting. Figs. 3 and 4 show the reactions caused by more or less vertical resistivity contacts and Figs. 5 and. 6 refer to the problem of ground-water and bedrock investigations where the resistivity contact is horizontal or nearly so. It is evident from Figs. 5a and 6a that qualitative measurements do not permit an identification of such general geological features as widespread horizontal strata, because the resultant contraction or expansion of the equipotential circles at the surface cannot be recognized without quantitative determinations. On the other hand, qualitative measurements are well suited for the exploration of local or lateral resistivity

Jan 1, 1931

By Carroll F. Hardy

The day by day loss of industrial plants to gas and oil is chiefly by default. The coal industry is not selling its superior economy, safety, and other advantages to its customers. THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer-subsidized private utility atomic power plants on one hand and super TVA's on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 1½ million units were lost in this 10-year period. In the non-central heating category, which principally includes stoves, the percentage declined from 39.2 to 25.6, but the units declined about 2½ million in number. The big increase was in heating units designed to burn gas and oil. Use of wood for central heating declined about one-third. Data on amount of fuels used for residential heating are not available, but information is on hand for residential and comnlercial space heating, see Table 11. Commercial space heating includes office buildings, churches, schools. and similar structures. The annual use of bituminous coal in these two categories declined about 1 million tons in the 10-year period. Other forms of solid fuel showed greater losses, except wood, which remained the same. Domestic stokers reached their high point in 1948 with about 1,200,000 in use. At the end of 1951 there were approximately 1,116,790 stokers in use. Conversions to gas and oil have been from hand-fired heating plants in the ratio of about 7 to 1 compared to stokers. In other words, for every one stoker which has been converted to gas or oil, seven hand-fired units have been converted to gas or oil. A bare recital of these data would indicate that the coal industry is holding its own reasonably well. However, 93.4 pct of the new homes built in 1951 were heated by gas or oil. Oil-burning equipment was installed in 37.8 pct and gas equipment in 55.6 pct of the new homes. This indicates that the public prefers gas when it is available, and that oil is second choice, with all forms of solid fuel apparently used when it is unavoidable. It must be pointed out, however, that during the period of rapid expansion of gas pipelines gas has been sold for house heating at prices that are in some cases actually lower than coal prices, or very nearly on a par. Gas has been sold at wells at far below the comparable price for oil produced from the same wells, and far below its actual worth. This situation is being remedied at the present time by increases in gas prices at the wells. For example, the wellhead price of gas in Texas averaged 7.494 per Mcf in 1952. In 1949 it was 4.59c per Mcf. This increase in price is being reflected in pipeline gas prices, and in most of the markets served by the pipelines the tendency is to get it out of the bargain basement type of sales. The American Gas Association estimates that at the end of 1952 there were in the United States about 11 million customers for gas house-heating, and the Association expects additional gains each year until around 18 million homes will be heated by gas in 1975. By 1975 there should be 60 million dwelling units to be heated in the United States, if dwelling units increase at the same rate as the population. If the gas industry heats 18 million dwelling units by that time, this still leaves 42 million units to be heated by some other fuel. If oil is used to heat 18 million dwelling units in that same year, 24 million would of necessity be heated by coal, coke, wood, electricity, or another fuel. The total number of dwelling units using coal listed in the 1950 Census was 18,776,000, so it would appear that coal has a chance at least to stand still in the tonnage sold for domestic use. In the first quarter of 1953, 2044 domestic stokers

Jan 1, 1955

R. H. Sweetser, Sault Ste. Marie, Ont. (communication to the Secretary*):—The recent work of furnace No. 1 of The Algoma Steel .Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mixture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 lb.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced 200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with

Jan 1, 1906

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By A. W. Fahrenwald

The function of the c1assifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred to as "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particu1ar method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted. Relation of Classifier Efficiency to Grinding Efficiency The energy of crushing, and therefore the cost, according to Rittinger's Law,l is proportional to the new surface exposed in crushing. Since the new surface produced in crushing is nearly proportional to the reciprocals of the diameters crushed to, it is obvious that the cost of crushing in the finer sizes is tremendously greater than in the coarser sizes for equal ratios of reduction. High circulating load of finished sand in the circuit of the classifier and grinding mill is therefore obviously expensive practice. It is the classifier's function to reduce this to a miniMum.

Jan 1, 1930

By G. P. Conard, R. C. Hall, J. F. Libsch

The 50 pct Fe-50 pct Co alloy undergoes a transformation from disorder to an ordered structure of the CsCl type reportedly in the vicinity of 732OC. During this process, the coercive force goes through a maximum, apparently as a result of strains associated with the coherent nucleation and growth reaction. This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction, which is associated with annealing to a high degree of order with the continuous application of a magnetic field. The increase in ratio can be explained on the basis of a decrease in 90' domain boundaries and, perhaps, by an increase in anisotropy resulting from lattice distortion. THE 50 pct Fe-50 pct Co alloy undergoes a disorder-order transformation which has been reported to occur in the vicinity of 732°C1,2 The ordered structure is the CsCl type.' This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction as a result of heat treatment in a magnetic field, sometimes called a response to magnetic anneal.'-' The purpose of this investigation was to study the course of the ordering reaction, the nature of the response to .heat treatment in a magnetic field, and the relation, if any, between ordering and the response. Procedure The method of approach in this investigation was to produce an initial structure as completely disordered as possible and then gradually to order the alloy by isothermal anneals at various temperatures under different conditions of the applied magnetic field. Magnetic, magnetostriction, and X-ray analyses were of primary importance in determining the property and structural changes resulting from the isothermal anneals. Rings of the 50 pct Fe-50 pct Co alloy were prepared from the elemental powders by a powder metallurgy technique, further details of which may be found in ref. 7. The initial structure was produced by annealing the specimens for ½ hr at 1000°C, cooling to and holding for ½ hr at 900°C (in the a range above the ordering temperature), and water quenching. Isothermal anneals were performed at 600°, 675°, 720°, and 740°C. For example, rings were heated to 600°C, held for a predetermined period of time, and cooled by natural cooling at a rate slightly slower than an air cool (average of 20" to 25°C per min). The tests (magnetic, etc.) were made after each heat treatment. All high temperature treatments were performed in a purified hydrogen atmosphere. The treatments at the various temperatures were carried out under one or more conditions of an applied field including 1—no field, 2—field of 20 oersteds applied on cooling only, and 3—field of 20 oersteds applied continuously during heating, holding, and cooling. Magnetic measurements were made using the standard Rowland ring technique8 with a maximum field strength of 100 oersteds. The magnetization curve, induction at 100 oersteds (B.), residual induction (Bt), and coercive force (Hc) were determined. All magnetic analysis data were based on an average of the results from three rings. A strain gage technique9 as used for the measurement of magnetostriction. The X-ray determination of the relative amount of ordered phase present was made on the ring specimen used for magnetic measurement. This was done by the back-reflection method using a rotating specimen (because of the large grain size) with unfiltered CoKa radiation and a 7 hr exposure time. Intensity measurements of the ordered line (300) were made by comparing visually the films so obtained with standard films prepared by exposing for different lengths of time a specimen given a long time anneal (high degree of order). Results In all instances the saturation induction (induction at 100 oersteds) was found to increase slightly with annealing time. This effect was small and appears to be the increase in saturation induction to be expected on ordering.10-13 The residual induction behavior was markedly influenced by the field condition during annealing, Figs. 1, 2. For the condition of no applied field, the ratio of residual to saturation induction remained essentially constant for short annealing times but showed a significant increase at longer times. With increasing annealing temperature, less time was required to produce this increase in the ratio. In the case of the 600°C anneals, the increase did not occur until approximately 20 hr, Fig. I, while on annealing at 740°C the increase was immediate, Fig. 2. Slight decreases in the ratio may be observed at 100 hr for specimens treated at 720°C and at 1 hr for those treated at 740°C. Specimens annealed in a field of 20 oersteds showed a residual to saturation induction ratio consistently higher than that for the specimens annealed without the field. The first anneal with the field (¼ hr) caused an abrupt increase in the ratio at all temperatures; thereafter, the increase in the ratio was generally similar for specimens annealed

Jan 1, 1956

By Alex McCoy

SAMPLING of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines-laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. LABORATORY INVESTIGATIONS ON EMULSIFIED OIL Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. S. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy,

Jan 8, 1919

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By C. N. J. Wagner, E. N. Aqua

Dilute Fe-Si alloys (0 to 5 wt pet Si) were cold-worked by making filings at room temperatuve. The analysis of the broadening of the X-vay powdev pattern peaks yields anisotropic particle sizes normal to the (110), (100), and (112) planes which are a consequence of deformation faults (probability a) and twin faults (probability p). The combined fault probability (1.5a +ß) increases from 0.01 in pure iron to 0.02 in Fe-5 pct Si. The root mean square stvains vary with crystallographic ovientation due to elastic anisotropy of the alloys, and increase from about 0.0035 in pure iron to 0.005 in Fe-5 pct Si measured in the [100] direction. Assuming that deformation and twin faults occur with equal probability, the X-ray data would imply that the stacking-fault energy does not change upon alloying. THE crystallographic aspects of the plastic deformation of dilute Fe-Si alloys has been studied many times since the observation of glide band structures by Barrett et a1.l These glide bands were much straighter than the wavy bands observed by Gough2 in unalloyed iron nearly 40 years ago. This difference in the morphology of the slip band structure has been verified many times, most recently by replication electron microscopy3 and dislocation etch-pitting methods.4,5 These observed differences in deformation behavior have been considered to result from the degree of cross slip that occurs in pure iron and in the Si-Fe alloys. The lowered tendency for cross slip would result from a lowering of the stacking-fault energy of iron by the silicon alloying addition. Experimental evidence for this lowered stacking-fault energy in the Si-Fe alloys, obtained with transmission electron microscopy, is the observation of dissociated dislocations in Fe-6 pct si6 and Fe-3 pct Si alloys,7 and the observation of sharply defined cellular substructures in Fe-3 pct si6,7 compared to the more diffuse substructure in zone-refined iron.' The activation energy for recovery of cold work is greater in the Si-Fe alloys than it is in pure iron, indicating that cross slip has become a more difficult process.9 The purpose of this investigation is to determine the change in stacking-fault probability from the broadening of powder pattern peaks in dilute silicon-in-iron solid solutions, when cold-worked at room temperature. The knowledge of the stacking-fault probability and the dislocation density, both of which can be deduced from line-broadening analysis of two orders of reflections from (110), (200), and (112) planes, will permit us to calculate the change in stacking-fault energy upon alloying silicon into iron. Previous X-ray investigation of cold-rolled Fe-5 wt pct Si (100)[001 ] single crystals did not reveal any line broadening, whereas cold-rolled Fe-3.1 wt pct Si (001) [110] and (001)[100] single crystals10 showed line bro2dening as a consequence of small particle sizes (-200A) and root mean square strains (-0.25 pct), which are comparable to those found in cold-worked iron filings.11 EXPERIMENTAL PROCEDURE A series of five Fe-Si alloys containing nominally 1 to 5 wt pct Si and pure iron were cold-worked by making filings at room temperature. The actual silicon content deviated at the most by +0.1 pct which is of no significance in the present study. The carbon contents of these materials were less than 0.02 pct. The X-ray diffraction patterns were measured with molybdenum, cobalt, and iron radiation using a GE and a Philips diffractometer. The (110)-(220), (200)-(400), and (112)-(224) pairs of reflections were

Jan 1, 1968

By W. T. Hicks

The oxidation of CbO was studied by a gravimetric technique from 400° to 1200°C in oxygen. In this temperature range the oxidatiotz is characterized by an irlductive period of low oxidation rate, which becomes shorter as the temperature increases, followed by a rapid parabolic oxidation. The oxidation of CbO cannot be rate controlling in the oxidation of Cb metal in the temperature range, 800° to 1200°C. A thin optically inactive layer has been observed between the metal and Cb2O5 layer of Cb oxidized at 700°C or higher temperatures. Figs. 1(a) and 1(b) show the edge of a sample of Cb reacted to 50 pct of complete oxidation at 800°C. Fig. l(a) taken under bright field illumination shows a layer of oxide adhering to the unoxidized metal core. Fig l(b) taken under polarized light shows that this oxide layer is

Jan 1, 1962

By S. F. Reiter, R. W. Guard, J. H. Keeler

DURING the last several years the authors have been conducting tests on a tensile machine that autographically records load-elongation data. In certain tests at elevated temperatures on face-centered cubic, hexagonal close-packed, and body-centered cubic materials (binary alloys of nickel, zirconium, and iron), the load-elongation curve as shown in Fig. 1 reaches a maximum load (Pmax,) at relatively small amounts of strain and a large amount of elongation occurs subsequently with a continuously decreasing load, until finally localized necking and fracture take place. This early maximum load behavior has been found without the accompanying evidence of localized necking as has been assumed by some, or of evidence of cracking as observed by others.' This behavior has also been observed by Nadai and Manjoinez whose results are in good agreement with ours. The prior strain, strain rate, test temperature, and crystal structure affect the observations. The influence of prior strain was observed in tests on unalloyed zirconium at 300°C in which specimens containing large amounts of prior strain (cold work) exhibited the type of curve shown in Fig. 1. No localized necking was observed after strain as much as that of point B. Annealed and recrystallized specimens of the same material showed a load-elongation curve with maximum load occurring after considerable strain hardening and at the beginning of localized necking. Interrupted tests (Fig. 2) show no loss in strength because of recovery or recrys-tallization during an interval at temperature without load. Recovery under stress such as found by Wood and Suiter3 in aluminum is now being investigated as one possible explanation. The strain rate is a contributing variable as shown in Fig. 3, a test on high purity nickel. Here the strain rate was decreased by a factor of ten during a test in which the maximum load was reached at a small strain. The slope of the true stress-true strain curve was positive with the more rapid strain rate and negative with the slower strain rate. In many binary ferrites an added effect of temperature has been observed. Fig. 4 shows the load-elongation plots for a binary ferritic alloy containing 2 pct Mo. The slope of the small portion of the stress-strain curve obtained at a strain rate of 0.01 mhr1 changes sign from negative to positive on going

Jan 1, 1955

By E. S. Bardwell

Each of the three refining furnaces in use at Great Falls is provided with a waste-heat boiler. The general arrangement of furnace and boiler is as shown in Fig. 1. Two of the furnaces have hearths 45 ft. 7 in. by 14 ft. 6 in.; the third has a hearth 46 ft. 101/2 in. long and of the same width as the other two. The furnaces at present are equipped for firing with natural gas. As originally constructed two of the furnaces had hearths 36 by 14 ft., and were designed to use coal on grates, but these furnaces were lengthened and fired successively with pulverized coal and oil. The third furnace was added in 1926 and was oil-fired until 1928. Since that year natural gas has been in use on all of the furnaces. The changes that have occurred in connection with furnace design and the comparative performance of the furnaces with various fuels were described1 by the author in 1932. Two of the furnaces are provided with Stirling class A-30 boiler. rated at 400 hp. and having 4008 sq. ft. of heating surface. The thir furnace has a class A-21 Stirling waste-heat boiler rated at 300 hp. with 2805 sq. ft. of heating surface. The boilers are not baffled. The waste-heat boilers are placed on a platform 17 ft. 3 in. above the level of the furnace charge floor. The waste gases from the furnace pass by a vertical uptake flue, 4 by 3 ft. inside at the point where it enters the chamber, to a brick chamber from which the gases pass over a bridge wall and into the boiler setting. The uptake flue and chamber are constructed of silica brick. Each furnace has a steel stack 125 ft. high, measured from the boiler floor. The stacks have a 41/2-in. firebrick lining and are 5 ft. in diameter

Jan 1, 1934

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948

By J. L. Jones

1. Brinell tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin. BRinell Habdness of Babbitt at Increasing Temperatures Bearings fail because of wiping, or deformation. Hence tenacity is desirable in a bearing metal, especially tenacity at high temperatures. The Brinell test is commonly regarded as a measure of tenacity. In fact, it has recently been proposed to substitute for Brinell hardness number the expression " tenacity number."l It seemed, therefore, that the Brinell test was especially adapted for the tests described. Disks, 4 in. (101 mm.) in diameter and 1.5 in. (38 mm.) thick, were made of the babbitts to be studied, designated A, B, C. They were poured into metal molds, pyrometer leads being soldered in the center of each disk. The composition of the babbitts was as follows:

Jan 1, 1919

By D. C. Jillson

THE data on the critical resolved shear stress for zinc single crystals published by Rosbaud and Schmid1 showed many irregularities, as seen in fig. 1. There have been subsequent investigations,2,3 but no one has repeated this work with a wide range of orientations, with specimens of a higher degree of purity and perfection, and with improved experimental techniques in order to determine whether these variations were entirely experimental or whether they might have been due, at least in part, to some feature of the mode of deformation not known or understood. Mathewson4 and others have long felt that the glide observed in a [100]* direction between two (001)* planes in the zinc lattice might be actually the net effect of many consecutive unit glides or movements in two alternating [210] directions (fig.

Jan 1, 1951

Jan 1, 1918

By Gerhard Derge

THE chemical and physical properties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use, These processes are carried out at high temperatures and involve such complex chemical systems that fundamental scientific knowledge of the properties and behavior of these slags is inadequate. Various hypotheses have been proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenck1 and the recent papers of Chipman and co-authors.2-5 Another proposal is that these compounds dissociate by completes or partial ionization, the evidence for which has been reviewed by Martin and Derge.7 Whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: I, Studies of solidified slag samples by X-ray diffraction, petrography, and similar methods that can be used at room temperature, The correlation of this information with the high-temperature properties of the molten slag is uncertain, 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature, However, even these data present problems of interpretation because they require a complete knowledge of the metal phase, 3, Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret, Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information, The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems CaO-SiO2 and CaO-A1203-Si02 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1946