Search Documents

By H. E. Lee, P. C. Feddersen

Greenockite is the only known cadmium mineral of importance. It occurs rather universally, in minor concentrations, as a secondary mineral in sphalerite deposits. The world's cadmium output is obtained through the processing of metallurgical by-products, largely from the treatment of residues from electrolytic zinc, retort zinc and lithopone plants. These sources are supplemented by the processing of fumes from lead and copper smelting operations. The development of modern selective flotation practice in the decade 1920-1930, which permitted the economical mining of complex lead-zinc ores, resulted in significant increases in the quantities of cadmium entering lead smelting systems. Being closely related to zinc as to occurrence, properties and production, most detailed description of cadmium recovery methods are to be found recorded in connection with zinc metallurgy. Other than occasional articles pertaining to particular operational procedures, literature offers but little in the nature of a balanced survey of lead smelter cadmium recovery practices. While many of the basic operations described for the recovery of cadmium from zinc by-products are applicable to the treatment of lead plant products, the inherent problems involved differ widely. In general the cadmium content of related by-products from routine lead smelting operations is present in lower concentrations, exists in a less soluble state and is associated with both a greater quantity and a greater variety of detrimental impurities. To cope with these problems, lead smelter practices are found to follow the general outline: Preparatory Processing 1. Concentration operations 2. Sulphation operations Cadmium Plant Processing 1. Leaching operations 2. Purification operations 3. Sponge precipitation operations 4. Metal recovery operations 5. Refining and casting operations As in the case of related zinc plant operations, cadmium recovery practices at lead smelters are not standardized. They not only vary as to type, but also extent. Depending upon prevailing conditions, lead smelter cadmium operations range from simple concentration campaigns, for the purpose of sufficiently "up-grading" products for shipment elsewhere, to complete processing steps for the production of refined metal. Preparatory Processing The cadmium content of lead smelter receipts is low and, as a rule, proportionate to the zinc content; the usual range of cadmium contained being of the order of 0.01-0.05 pct. Were it not for the low boiling point of cadmium, such small concentrations would, no doubt, be lost in the large tonnages of slag, metal and other smelter end products. However, the ready volatility of cadmium and its compounds at prevailing lead smelting temperatures results in its concentration in fractional portions of fume collected. This collected fume comprises a circulating load within the smelter system. Thus, the cadmium content of blast furnace fume* increases with each successive circulation until an equilibrium value is reached when the sum of the cadmium losses, due to handling and in slag, waste gases and other end products, becomes equal to the intake as ore. With ore receipts averaging, say 0.03 pct cadmium, the concentration value obtainable, through fume circulation in a routine manner, approaches 10-12 pct. In such operations, cadmium concentrations in blast furnace fume of from 3-5 pct are readily .attainable. However, the concentration gain beyond this range, with each additional circulation, is progressively decreased as a result of mounting losses occurring through handling and in end products. Therefore, to avoid excessive cadmium loss and to enhance the ultimate concentration anttainable, it is customary practice to isolate blast furnace fume at some intermediate cadmium content for special concentration procedure. The most common type cadmium concentration "campaign" involves special smelting operations wherein a relatively high portion of blast furnace fume at 3—6 pct cadmium is incorporated into the sinter charge. This type practice is roughly illustrated by the diagram on p. 111. Cadmium fume collected from lead blast furnace operations is not amen-

Jan 1, 1950

By Henry T. Mudd

FLUORSPAR is a nonmetallic mineral aggregate or mass containing a sufficient quantity of fluorite (CaF2) to be of commercial interest. It has only moderate value per unit of weight and its cost as a percentage of the cost of finished consumer products is nearly negligible. Nevertheless, it has wide and great industrial importance. In periods of national emergency it is a mineral without which many very necessary manufacturing processes would be greatly handicapped; a few could not exist. Fluorite contains 51.1 pct calcium and 48.9 pct fluorine. Industrial grades of fluorspar prepared for the consumer normally contain from 85 to 98 pct fluorite, depending on the use. The ores may contain as little as 30 pct fluorite, depending on many factors such as accessibility to transportation and markets, character of ore, and prices. Fluorite is a lustrous, glasslike mineral, generally translucent to transparent; it may be clear and colorless or range in color from slightly bluish through various shades of violet, amethyst, purple, green, and yellow. It crystallizes in the isometric system and possesses perfect octahedral cleavage. Commonly it occurs in masses of very pure crystal- line material with aggregates of cubical crystals in open spaces, but - it is also found in fine to coarse granular form. Banded veins and masses with fibrous, radiating structure occur locally. It is usually found associated more or less intimately with other minerals and rocks, from which it must be separated for commercial use. The specific gravity of fluorite is 3.18 and the hardness is 4 in the Mohs scale, compared with 7 for quartz and 3 for calcite. It is distinguished from calcite by its failure to effervesce with dilute hydrochloric acid. Heated with sulphuric acid, it gives off fumes of hydro- fluoric acid, which etch glass.22,25,33.34,35.41

Jan 1, 1949

By M. T. Simnad, R. F. Mehl, L. Yang

Techniques for studying marker movement in K-Rb interdiffusion have been worked out. The results indicate that Rb diffuses faster than K and that the ring mechanism of diffusion cannot be the dominant one operating in this case or probably in cases involving other alkali metals, despite their low ion core repulsive energies. SEVERAL theoretical attempts have been made in the past decade to elucidate the mechanism of diffusion in body-centered-cubic metals. No general agreement, however, has been reached by different authors. Zener,1 and later LeClaire,2 on the basis of a correlation between the entropy of activation for self-diffusion and the temperature dependence of the elastic constants, predicted that a ring mechanism should operate in the diffusion of body-cen-tered-cubic metals. Paneth3 calculated the activation energies of various ring, vacancy, and interstitial mechanisms for the self-diffusion in alkali metals and concluded that the most likely one was based on the linear motion of "crowdions," which is in fact a different form of interstitial diffusion. Fumi,1 however, showed that the experimental values of the activation energies for self-diffusion in the alkali metals could be better accounted for if the diffusion process in these metals was assumed to follow a vacancy mechanism. The same conclusion was reached by Kojima5 for the self-diffusion in lithium. Experimental evidences published during the past few years seem to exclude the ring mechanism as the predominating one in the diffusion of body-centered-cubic metals. For instance, maker movement has been observed in ß-brass, first in this laboratory" and later by Resnick and Baluffi.5 Shewmon and Bechtoldh also found marker movement in the body-centered-cubic system Ti-Mo and showed that the argument which led Zener and LeClair to favor a ring mechanism was not incompatible with a vacancy mechanism. In spite of this, it seemed to the authors that further experimental tests should be made by studying the Kirkendall effect in body-centered-cubic systems that characteristically have small ion core repulsion, such as the alkali-metal systems. Since the ion core repulsion term constitutes the main part of the activation energy needed for the rotation of a ring, such a test should be the most critical of all. The system K-Rb was chosen for experimental study because these metals form a continuous series of solid solutions. Experimental Investigation Owing to the extremely active nature of these two metals, a brass dry box (18 x 11 x 10 in.) was built for making the diffusion couple. It had a big lucite window on top, two side ports through which neo-prene-rubber gloves were inserted, and another side port covered with an optically flat-glass window for microscopic examination of the sample. Inside the box there were a circulating fan driven with a rotating horse-shoe magnet located outside the box, a heater used to generate potassium vapor for getter-ing the box, and a cold trap for keeping the inside of the box cool. Chemically pure grade K and Rb were triple distilled before they were transferred in vacuum into cylindrical steel molds kept in pyrex-glass ampules, Fig. 1. The latter together with the tools needed for making the diffusion couple were put into the dry box. After the box was flushed with purified argon and gettered with potassium vapor, generated from a heated steel crucible inside the box, the glass ampules were broken and the mound on the top of the alkali-metal ingot was cut off with a razor blade to yield a flat surface. To make the diffusion couple, one K ingot and one Rb ingot were pushed out of the molds together with their steel supports by screwing a metal plunger into the bottom of each mold. They were then laid on a brass cradle inside the assembling carriage (shown separately in Fig. 2) with the flat faces opposite to each

Jan 1, 1959

By John L. Schroder

The demands for increased productivity on the 1967 coal industry have generated new operating trends and fresh approaches to old methods, which have enabled the industry to keep pace with the expanding economy. Changes, while not radical in concept or design, have been plentiful and are marked by the refinement of the already tried, tested and proven. Perhaps not since World War II have there been demands on equipment manufacturers to design and deliver such diversified types of machines as those required by the industry in the past year. Equipment developments-following a plan which calls for higher productivity, lower maintenance costs and greater machine availability- have tended more toward increased horsepower and heavier, more rugged equipment. Electrical and mechanical components, designed in many instances with maximum reliability rather than initial costs as the main criterion, have contributed to the improvements in over-all performance. High-strength, specialty steels are finding use in a wide range of equipment applications. The horsepower capacity of electric motors being installed is more frequently being rated on a continuous basis rather than the former one hr or less and, as a result, fewer failures now occur because of overloading. These developments reflect the pyramiding cost of equipment down-time and represent definitive progress in reducing the magnitude of the problem.

Jan 2, 1968

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-' pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.' and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By Erwin Zodrow, De Verle P. Harris

The Smallwood mine, owned and operated by the Iron Ore Co. of Canada, is one of the largest ore producers in Canada, producing about 15 million tons of crude ore per year. Located in the Labrador Trough near, Labrador City, Newfoundland, the open-pit operation has ore consisting chiefly of specular-hematite, with some magnetite. The magnetite content of the ore as a mineral percentage is small, but it is of considerable importance in ore grading because of its effect upon milling. Being harder than specular-hematite, magnetite increases grinding time and milling costs. Specifically, higher grade magnetite (greater than 15%) usually occurs as fine grains in a fine grained siliceous rock matrix (also as larger octahedra in carbonate bands). This tends to increase the overall breaking strength in the crude ore; consequently, the hourly mill rate and the weight recovery decrease. At the same time, because of its relatively high iron content, the magnetite does contribute to the amount of iron in a block of ore. Were the concentration of the magnetite relatively constant, its presence would be of less consequence, for appropriate adjustments could be made in the milling operations. However, the quantity of magnetite present for any run of ore varies considerably; it is the magnetite prediction for a block of ore that constitutes the greatest problem in grading. THE PRESENT ORE GRADING METHOD Ore for the Smallwood mine is graded by a computerized block grading routine (using 50 x 50 x 45-ft blocks) that applies simple weighted (inverse-distance) averaging to ore grades. The results of the block grading program are not reliable with respect to magnetite concentration. Factors responsible for this poor estimation are (1) the structural setting of the deposit, and (2) mineralogical relationships. Neither of these general factors are given adequate consideration by present methods.

Jan 8, 1967

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

On Feb. 16, 1948, the Board of Directors of NME authorized the publishing of "Technical Notes" in METALS TECHNOLOGY. The purpose is to provide prompt publication of very short items of the following general types: I. Results of short investigations which do not warrant a paper. 2. The conclusions of extensive investigations of insufficient general interest to justify a regular paper. 3. Conclusions arising in the course of an investigation, which, because of interest to others in the field, the author wishes to present prior to completion of the investigation. 4. Pertinent factual comment (not mere argument) on the subject matter of previous "Notes." Such Notes will be subject to the approval of the Auxiliary and AIME Publications Committees, but can be handled more promptly than regular papers because they need not be referred to readers. The recommended maxi- mum length is 500 words; notes in excess of 1,000 words will not be considered for this type of publication. A graph or photograph may be included as part of the note when particularly illustrative. As with regular papers, contributions to the new section should be submitted to the Secretary of the AIME. Please furnish two copies each complete with illustrations.

Jan 1, 1948

On Feb. 16, 1948, the Board of Directors of AIME authorized the publishing of "Technical Notes" in METALS TECHNOLOGY. The purpose is to provide prompt publication of very short items of the following general types: I. Results of short investigations which do not warrant a paper. 2. The conclusions of extensive investigations of insufficient general interest to justify a regular paper. 3. Conclusions arising in the course of an investigation, which, because of interest to others in the field, the author wishes to present prior to completion of the investigation. 4. Pertinent factual comment (not mere argument) on the subject matter of previous "Notes." Such Notes will be subject to the approval of the Auxiliary and AIME Publications Committees, but can be handled more promptly than regular papers because they need not be referred to readers. The recommended maxi- mum length is 500 words; notes in excess of 1,000 words will not be considered for this type of publication. A graph or photograph may be included as part of the note when particularly illustrative. As with regular papers, contributions to the new section should be submitted to the Secretary of the AIME. Please furnish two copies each complete with illustrations.

Jan 1, 1948

By L. C. De Jong, J. F. Shirley, M. L. Campbell

At the Southern Peru Copper operation in Toque-pala, Peru, a new process flowsheet for the recovery of byproduct molybdenite has proved successful in dealing with complex and highly variable ores. This paper describes the process and the functions of each of the chemicals used. The Toquepala concentrator of the Southern Peru Copper Corp., located approximately 720 miles southeast of Lima near the Chilean border, processes a daily 36,500 tons of ore containing between 0.50 and 3.00% copper. The molybdenite content in the ore also varies greatly ranging from essentially nothing to as high as 0.15%. The 1966 yearly averages were approximately 1.20% copper and 0.03% molybdenite. The Toquepala porphyry deposit is a mushroom-shaped ore body consisting of a flat-lying enriched zone of predominant chalcocite with a stem-like extension of hypogene chalcopyrite ore in depth within and around a large breccia pipe.1 The underlying chalcopyrite ore has not been reached; however, due to the presence of a major post orebody fault, predominantly chalcopyrite ore is present in the north side of the pit. Most of the molybdenite occurs either as small, fine granular, pulverulent masses in vugs or empty voids of breccia, or as thin foliated masses and narrow thread-like filling in rock joints and fractures. The normal occurrence of quartz gangue with the molybdenite gives some basis for correlating the molybdenite mineralization to some later periods of silicification. On April 18, 1962, the molybdenite recovery plant at Toquepala went on stream, approximately 27 months after the copper concentrator had been in production. The plant was designed and built by Southern Peru Copper Corp.'s engineering and mechanical departments. The basic method chosen for separating the molybdenite from the copper concentrate was the sodium hypochlorite-sodium ferrocyan-ide process. The selection of this process was based on the results of an extensive testing program performed by the Colorado School of Mines Research Foundation, Inc. and the economic conditions of the area. The originally designed process could never be fully implemented due to a lack of sodium hypo-chlorite and has had to be continually modified to satisfy the requirements of the kaleidoscope of ores from the mine. The three basic problems that plague the operation of any molybdenite recovery plant are all present at Toquepala in large measure. Both the quantity of plant feed and the quantity of molybdenite contained in the plant feed are continuously changing. Even more detrimental to an efficient operation is the fact that the copper mineralization in the feed frequently changes once in every 24 hours and occasionally once a shift. From the point of view of the molyb-

Jan 1, 1968

By W. W. Odell

THE sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. So universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only- the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question.

Jan 9, 1919

By Bernard Lallement

INTRODUCTION Geostatistics have been used for five years at the B. R. G. M. to compute the ore reserve estimation. At present this technic is also used at the beginning of the exploration project to determine the best way to prove the orebody. The best way is a compromise between the cost of the exploration and the precision of the estimation. It is clear that geostatistics cannot be used without any data, but very often an exploration project is decided on an orebody which has already been drilled. Old data can therefore be used. This was the case this year for two orebodies: an iron deposit and a lead deposit. The iron deposit was explored by drifts and has now to be proved. We used geostatistics to determine the best drilling pattern. The variograms computed with these old data showed that an anisotropy existed between the two directions of the orebody, which meant that the drill pattern had to be rectangular. The lead deposit was explored by drill holes and a short drift in part of the orebcdy. The problem was to choose between a regular pattern of drill holes or a long drift and some added drill holes. The case of this study will be exposed afterwards. On the other hand, if the orebody is completely unknown, the exploration project generally forecasts two exploration steps (the first step

Jan 1, 1977

By A. A. Collins

When we speak of high copper on a lead blast furnace we think in terms of 4 to 5 pct, or. any lead charge carrying over 1 pct. Any copper on charge will produce its corresponding troubles such as lead well, extra slag losses, drossing problems, and the working up of the dross. This is indeed a very interesting subject and one that used to give the old-time lead metallurgists such as Eiler, Hahn and lles many worries, not so much in the actual operation of the hlast furnace but in the working up of the copper. When the American nletallurgists commenced with the American rectangular-shaped lead blast furnace in the 1870's and got away from the reverberatories such as were in use in Germany and other parts of the world, they went to greater tonnages, as 80 to 100 tons per day in comparison to the 20 to 30 tons per day in the other processes. With the greater tonnages along with insuficient settling capacity, the silver losses in some cases were increased. Hence the lead-fall was low, for there were no leady concentrates in those days to assist the metallurgist to gain lead or an absorber for the precious metals; and in some cases copper sulphides were added intentionally to the charge to produce a copper matte to lessen the silver losses through the dump slag. The operators in those days thought that where some copper was always present in the lead ores the copper should not enter into the reduced lead and alloy with it. This, by the way, is just the reverse of our present-day practice, when we try to put all of the copper into the blast furnace lead and to remove the same through the drossing kettles. Therefore the furnace was operated to produce a certain amount of matte or artificial sulphides, since, due to the great affinity of copper for sulphur, any copper present would enter the matte almost completely. Thus, the lead bullion produced was practically free from copper. The products of the furnace were metallic lead or lead bullion, containing 05 to 95 pct of the lead and about 96 pct of the silver which were in the ore—a lead-copper-iron matte which contained nearly all the copper in the ore and the slag, the waste product. In the United States, up through the year 1092, we find the small furnace 100 X 32 1/2 in. with 12 tuyeres, some 6 on each side, plagued with a small amount of poorly roasted sulphides— either from heap or hand roasters that produced matte. This matte was roasted and if poor in copper was returned for the ore smelting. Otherwise it was smelted either alone or with additions of rich slags or argentiferous copper ores, the products being lead and a highly cupriferous matte, the latter being subsequently worked up for its copper. The lead metallurgists kept trying and improving on furnace and roasting equipment designs until we find blalvin W. Iles constructing at the old Globe Plant at Denver what came to be the modern furnace. That is, in 1900 he built a furnace of 42 in. width by 140 in. at the tuyeres with a 10 in. bosh and a 16-ft ore column. This type has been more or less standard to the present time, though modified in width and length to meet the demand for large tonnages and improvements in structural details. In 1905 at Cananea, Mexico, Dwight and Lloyd developed the present down-draft sinter machine that has meant so much in producing a well-processed material for the lead blast furnace. In 1912 Guy C. Riddell came forth with double roasting at the East Helena Plant of the American Smelting and Refining Co., which removed the "zinc mush plague." Incidentally, with the introduction of double roasting, which most lead plants were forced into after 1924, when lead flotation came into its own, less matte or no matte was produced. When this stage arrived, the copper was forced into the dross and the casting of lead at the blast furnace lead-wells was stopped. In plants with a fair copper carry 1 pct or better on the blast furnace charge, the lead wells became inoperative once the production of matte stopped. The copper drosses clogged the lead wells and even with bombing, either water or dynamite, the operators could not keep them open. Thus, the lead wells were abandoned in some plants, such as at the El Paso and Chihuahua smelters of the American Smelting and Refinillg Co., and all lead taken out through the first settlers. The elimination of sulphur, espccially sulphide sulphur, from the blast furnace charge and the nonproductiori of matte resulted in a great saving of tinie, energy and equipment in the recirculation of the copper, With the copper content in the dross and dross-fall ranging in quantities from a few percent up to 60 pct, such as at El Paso, a drossing problem was created. As the old-time operators hated dross and buried the same in the shipping bullion, the modern metallurgists from 1925 on decided that with increasing dross-falls they would have to adopt the lead refiner's ideas of drossing kettles with subsequent treatment of the lead with a sulphur addition to have the shipping lead of 0.01

Jan 1, 1950

By Charles A. Lindberg

Mobile cranes on tires are perhaps the most important accessory in truck-haulage pits. They usually are of 20-ton capacity at short radius and with outriggers but have considerable overload capacity. Standard booms are 30 ft but have 10-ft extensions with which they are usually operated. Cranes have two engines, both originally gasoline, but 150-hp Diesel engines have been found more reliable for the propulsion motor, the 100-hp gasoline motors being retained for hoisting. Pro- visions are made for dropping the ballast counter- weight to reduce axle weights to legal limits for highway travel. The weights are carried on a regular truck or are transported on an extra trailer axle behind the crane. Tractors-Probably equalling the cranes in usefulness are the track-laying tractors which are used to prepare roads and other surfaces, to clean up at the shovel, and for dozing on stripping dumps. A new type of tractor mounted on rubber tires has been tried out on the Mesabi Range for the past year and a half. The advantage of this design is its mobility which makes it capable of taking care of the spill at the shovel and then running to the dump to clean up. Alternating between these two jobs, it relieves heavy tractors that can be used to better advantage on heavier work that does not require so much traveling. This tractor can travel at speeds of 12 to 13 mph and is designed to facilitate repair of the expendable parts. Weaknesses have developed in the internal construction which have seriously marred the performance record of this unit, but when used within its capacity it is quite successful.

Jan 1, 1949

By R. M. Waterstrat

The phases occurring in the V-Mn system were studied by means of X-yay diffraction and metallo-paphic techniques, using are-melted alloy specimens annealed in the temperature range 800° to 1150°C and quenched. The bcc solid solution extends at 1250°C all the way from vanadium to 6-manganese. Below 1050°C the a-phase is formed, and the terminal a-manganese phase is stabilized up to about 900°C by vanadium in solid solution. IN the only previous general survey of the V-Mn system Cornelius, Bungardt and Schiedtl reported the existence of three intermediate phases corresponding to the approximate compositions VMn,, VMn, and V5Mn. The phase VMn8 has recently been identified as a o phase2 but the alloy VMn was found to have a bcc structure2 corresponding apparently to the vanadium solid solution rather than to the large cubic unit cell reported by Cornelius et al. 1 Subsequent work by Rostoker and Yamamoto3 has shown that the vanadium-base bcc solid solution extends to at least 15 pct Mn at 900°C. An alloy corresponding to the composition VMn, was examined by Elliott,4 who reported that the as-cast sample as well as samples annealed at 1200o and 1300°C had bcc structures, but that annealing at 1000°, 800") and 600°C produced two phases. One of these phases was apparently the bcc solid solution and the other resembled the o phase structure. Hellawell and Hume-Rothery5 established the phase relationships in manganese-rich alloys above 1000°C, and showed that the o phase in this system is replaced by the 6 Mn (bcc) solid solution at temperatures above 1050°C. These results suggest that a continuous bcc solid solution may exist above 1050°C between vanadium and 6 Mn. The present investigation was undertaken in order to develop more complete information in regard to this system. EXPERIMENTAL METHODS The alloys used in the present work were prepared by arc-melting electrolytic manganese having a minimum purity of 99.9 pct and vanadium lumps with a purity of 99.7 pct. The major impurities present in these metals were carbon, nitrogen, and oxygen and this would account for the small percentage of nonmetallic inclusions observed metal-lographically. The arc-melting was at first performed under a helium atmosphere and it was necessary to keep the melting times as short as possible in order to minimize the loss of manganese by vaporization. It was later found that the evaporation of manganese was considerably reduced when the melting was done under argon atmosphere. The final composition of each alloy was calculated by assuming that the total weight loss during melting was due to evaporation of manganese. Compositions which were calculated in this manner agreed reasonably well with the results of chemical analysis, as shown in Table I. Spectrographic analysis revealed the presence of contamination by tungsten, but in no case was the percentage of tungsten greater then 0.4 at. pct. The specimens were in each case broken in half and the fractured section was examined visually and microscopically for evidence of inhomogeneity. Each specimen was homogenized at temperatures near l100°C, as shown in Table I. After this treatment most specimens consisted of large columnar grains of the bcc vanadium solid solution. The etchant used in most of the metallographic work consisted of 20 pct nitric acid, 20 pct hydro-flouric acid, and 60 pct glycerine. It was found that this etchant would clearly delineate the phases present in these alloys although it does not produce any striking contrast between the phases. For certain manganese-rich alloys, a 1 pct aqueous solution of nitric acid was used. This etchant gave a brown color to the a-manganese phase, whereas the o phase was virtually unattacked and appeared very light as shown in Fig. 1. The etchants used by Cornelius et a1.l were found to produce spurious effects in some of these alloys. In particular, the vanadium-rich alloys etched in hot sulfuric acid often appeared to consist of two phases when both X-ray diffraction and etching with the glycerine-acid mixture indicated the presence of single phase bcc solid solution. A few percent of what appears to be an oxide or nitride phase was found at the grain boundaries and in the interior of the grains, especially in the vanadium-rich alloys. All alloys were annealed in sealed silica tubes containing 1 atm of pure argon and these tubes were then quenched in cold water. Although some manganese loss occurred during annealing, the loss seemed to be confined to the surface of the speci-

Jan 1, 1962

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946