Search Documents

By Gerasimenko MP

The authors consider the features and advantages of a new promising trend in mineral processing - column flotation. Design aerohydrodynamic and process characteristics of pilot-scale columns are studied. Optimum process parameters for various ores and operations are studied. Flow patterns in cells of various cross-sections are investigated and the relationship between Peclet criterion and specific capacity of cell is determined. On this basis options were developed for optimisation of hydrodynamic characteristics of large capacity cells, including longitudinal sectionalising of the collection zone. It is shown that advantages of high column cells (10 - 13 m) produced in the West can be implemented in a sectionalised machine of smaller height (5 - 6 m). Investigations on the influence of slurry and air bubbles flow patterns indicated that to increase flotation rate of particles of various flotabilities it is expedient to combine co- and counter-current flows of phases in a single column. The proposed designs allow tailings to repeatedly return tailings to the collection zone and alternate co- and counter-current slurry and air flows. For the first time columns with alternating slurry flows (combination of co- and counter-current flows) are developed and commercialised. Unique multi-sectional cells having a number of essential advantages compared to monocells are developed. Design features of the cell allow: implementation of different flotation process flowsheets in a single unit, improved beneficiation process results, reduced specific power requirement, and elimination of sludging of the aerator and cell bottom part. Operational problems restricting introduction of column cells are connected with the aeration unit. The new cells are supplied with pneumohydraulic and stepped airlift spargers, allowing control of bubble size distribution with a service life of not less than three years. Successful operation of the new generation of columns with cell volumes of 15, 25, 40, and 80 cu m and the height of 5 - 6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants in this country illustrated their considerable process and operational advantages and verified the proposed options and relationships. A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calculating the design of commercial-scale columns is developed.

Jan 1, 1993

The Effect of Mineral Liberation on the Floatabilities of Pyrite, Arsenopyrite and Arsenian Pyrite for Carlin Trend Ores

Sep 13, 2010

In todayÆs evolving and globalised world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to æengageÆ communities and measure the success of these engagements without a clear understanding of æhowÆ to do this. This move, away from compliance, develops more of a focus on sustainability and æcommunityÆ social responsibility rather than corporate social responsibility. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of æengagingÆ communities in mining project design and development leads to sustainable development, a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be æengagedÆ in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this æengagementÆ and manage this risk will be discussed.

Jan 1, 2007

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha, H B. Wurst

In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink–?float analysis. Using traditional sink–float method it is not possible to sample and automatically measure. This fact, as well as time, cost and safety aspects, as well as required and manageable sample size of the sink–float method have prompted the search for a new approach for establishing separation performance criteria. This is especially important as performance levels of separator plants can be maximised if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes available in time. The new method to establish washability and associated performance information utilises at least two measurement technologies concurrently: single energy X-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy X-ray transmission and image processing.If used as a standard laboratory device the continuous build-up of the washability curve allows to evaluate the statistical significance of the sample size during measurement.The measuring method can even be improved if it is combined with an automatic sampling system that feeds a continuous and representative particle stream to the analyser. Then the value of the collected data increases considerably since the washability data are additionally available in time to be considered in the control of the process plant. The washability curve can be derived and is continuously updated based on the particles measured during the past time interval. Older curves and results are stored in a database and can be retrieved for later reference. This technology now enables automated sampling and integrated automated measurement, which was previously not possible.This incorporation of an automated washability monitor at a representative sample gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested using a range of samples with different densities, varying from 1 g/cm3 (coal) to 5 g/cm3 (iron ore).CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P, Wurst, H B and Ha, J, 2017. Inline analysis of washability parameters for process control, in Proceedings Eighth World Conference on Sampling and Blending , pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R Lethlean

The mining industry in its drive to optimise equipment use and minimise cost simply to remain profitable in an uncertain commodity market needs to develop a greater understanding of equipment capabilities and cost. The factors influencing mobile equipment fleet cost and performance commence at the time of mine planning and continue to exert an influence over the life of the mine. These factors must be understood at the early stages of any operationÆs planning process as they continue to impact both positively and negatively on fleet performance and operating cost throughout the life of the mine. The key factors examined in this paper include: grades; rolling resistance; fragmentation and truck loading.

Jan 1, 1998

By M Gwynne

McArthur River Mine is located approximately 50 km south-east of the NT township of Borroloola and approximately 120 km from the Gulf of Carpentaria. The mine hosts a series of layered shallow dipping tabular orebodies, with current reserves of approximately 22 Mt, grading 13.6 per cent zinc, 6.3 per cent lead and 65 g/t silver. Owing to economic considerations, the lower most orebody (No 2 orebody) has been selected for initial mine production. Following the completion of the No 2 orebody, mining will transfer to the lower grade and metallurgically more complex No 4 orebody. The mine employs a total of 235 people throughout the underground and surface areas. The majority of the workforce work a fly-in/fly-out, seven-day- on/seven- day- off roster with 12-hour shifts. Presently, a further 18 contractors are involved in trial mining areas. An apparent dip room and pillar technique has been selected as the primary mining method. Officially opened in September 1995, the current production rate of 1.2 Mt per annum will eventually escalate to 1.5 Mt per annum. Though most production is achieved through the use of conventional loaders, trucks and jumbos, the recent development of methods utilising scrapers, hand held machines and modified jumbos has produced encouraging results in steeper dipping areas of the mine. Initial production has been hindered by several factors including extensive and largely unpredictable faulting, worse than expected ground conditions and difficulties with some mining equipment. Compounded by the relatively thin 3 m ore seam, initial mining resulted in high dilution and poor production. This paper describes the development of unique planning and production systems that were evolved in order to overcome these problems and achieve the targeted production rates and head grade.

Jan 1, 1998

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

By A T. Yuniar, C A. Brannon, N D. Pascoe, H H. Firdausi

This paper describes the key components of the Grasberg Block Cave (GBC) mine design and the development and construction status of the mine. Drawpoint production from GBC will be initiated in 2018 following the closure of the Grasberg open pit. Full production of 160 000 t/d is planned for 2024, which will make it a 20-year time period between initial access development in 2004 and full production.Diluted ore reserves are about 1 Bt at a grade of 1.0 per cent Cu and 0.78 g/t Au. The mine plans some 2400 drawpoints on a 20 m × 30 m drawbell spacing in a 700 000 m2 footprint using the El Teniente layout. The drawpoint opening sequence includes five production blocks, the first two of which are scheduled to be undercut simultaneously in 2018. Ore is transported using diesel-powered load-haul-dumps to a series of orepasses and then delivered via loading chutes to a rail haulage system, which delivers the ore to a three gyratory crusher complex. Crushed ore is transported to the mill stockpiles via dual inclined conveyors.Development and construction of the substantial fixed facilities are now well underway. Primary access for personnel and materials is via the 6 km Ali Boediardjo (AB) adits. A service shaft will hoist personnel and materials from the AB adits level to the various operating levels. Shaft commissioning is scheduled for late 2015. The rail haulage system installation and construction is in progress and is due to be commissioned in 2017, which is timed to coincide with the commissioning of the ore handling system. Ventilation is provided through a series of large intake and exhaust drifts, and two of the four main fans have been commissioned. A 1600 L/s pumping system will manage drainage from the mine.Other key facilities include separate shops for rail and rubber-tired equipment, warehousing, a powder magazine, a main control centre and an underground concrete batch plant.CITATION:Brannon, C A, Firdausi, H H, Pascoe, N D and Yuniar, A T, 2016. Development and construction update of the Grasberg block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 625–634 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

Near-Infrared Spectroscopy (NIRS) Sorting in the Upgrading and Processing of Skorpion Non-Sulfide Zinc Ore In 2008 Anglo American sponsored a research project at RWTH Aachen University to assess the feasibility of the use of near-infrared spectroscopy (NIRS) for ore waste discrimination at the Skorpion zinc mine. The Skorpion mine is an open pit zinc mine located in Namibia, owned by Anglo American with an annual production of 150 000 t/a of super high grade pure zinc. Opportunities for the implementation of NIRS sorting for the Skorpion process exist to upgrade currently subeconomic material, including the marginal dump (over 2000 000 tonnes, av grade of 2.5 per cent Zn). NIRS sorting is not yet implemented or established in the minerals industry however it is a proven technology in the plastics recycling industry, where more than 2000 NIRS sorters have already been installed. NIRS sorting, a type of sensor-based sorting, is a single particle sorting technique which classifies the particles based on the absorbed/reflected radiation in the near-infrared (NIR) region. A disadvantage of NIRS is that it is a surface measurement technique, but NIRS sorting shows overall great potential for the minerals industry. Skorpion ore minerals include zinc bearing phases such as sauconite, hemimorphite, smithsonite, and hydrozincite. These display diagnostic responses in the near-infrared. There are three major absorption features that characterise the reflectance spectra of the ore bearing minerals. These are due to OH and H2O molecular bonds. The spectral response of the waste material is caused by other minerals such as non-zinc-bearing clay minerals, calcite and impure quartz. Test work showed that it is theoretically possible to separate ore material from most waste material based on spectral response in the NIR region. In addition to upgrading material by removal of waste it is also potentially feasible to classify the material based on zinc grade. A tentative correlation between zinc grade and spectral response seems to exist for the sample test suite in the NIR region.

Sep 13, 2010

Resources and reserves are critical inputs into the determination of an operating mineÆs financial results and balance sheets, but how well understood is this fact. Do the investors, directors, accountants and geologists/engineers responsible for preparing or relying on relevant aspects of the end results properly understand the inputs and outputs and the associated risks that may be established. The first step is to understand how financial reports are impacted. The most obvious, and best known, impact is in the calculation of depreciation and amortisation charges against long term assets. In addition, however, there is a requirement to regularly determine whether asset book values are impaired û this is nearly always performed globally by the preparation of a discounted cashflow model for a mine which is usually based on a mine life as determined from the resource and reserve statement û the particular driver here is normally the short and long term production plans. A key aspect of the short term production plan is that it would normally not assume that the reserve and resource statement implies consistent grade, stripping ratios, etc. However, outside of the early years of a plan, more generic assumptions of these variables are often made in conjunction with the reserve and resource statement. Depending on the timeframe of the detailed production plans, this can have a large impact on a projectÆs net present value. Other financial balances that may also be impacted include restoration and rehabilitation provisions, retrenchment provisions and deferred or equalisation stripping accounts. The age old question of whether all reserves should be used or whether some or all of the resources should be included for financial reporting purposes has never been adequately resolved. It is our view that there should be no prescriptive answer to this question but judgement of all professionals involved in the process needs to be included. Furthermore, the company needs to be able to support their conclusions with well thought out and appropriate answers. This may not be in line with the approach that certain accounting standard setters may be proposing or taking, and this paper will outline the current status of global requirement and the likely future directions. Whether reserves or resources are utilised, does not change the key requirement that those preparing or using reserve and resource statements need to understand key aspects. For example: geologists/engineers do they know how reserves or resources will be used? have they imparted information on variability of key drivers such as grade or depth or dilution? do they know that major financial/business altering decisions may be made based on the analysis? accountants do they understand where the numbers have been derived from and the assumptions that may have been made in their determination? do they understand the degree of accuracy (or inaccuracy) that may exist particularly with resources)? do they understand the history of resource reconciliations and what it may mean for the future? directors do they understand the processes undertaken by the company to prepare the financial report and the interaction between the geologists/engineers and accountants? do they understand the potential sensitivity of results to the input variables? Financial reporting is extremely reliant on the use of the reserves and resources, however, the geologists/engineers, accountants and directors do not always understand the interactions between themselves which may lead to misleading public reporting. More education and communication between various parties is needed.

Jan 1, 2002

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By N F. Fraser

Seafield ResourcesÆ offshore placer gold project covers c.10 000 km2 of the Westland continental shelf between Karamea and Jacksons Head, from the low-water mark out to the 120 m isobath (Figure 1). De Beers Marine (DBM), the marine diamond subsidiary of the De Beers Group, will carry out the project with geological input from Placer Solutions (PSL). DBM bring a wealth of expertise and advanced technology to the project, developed during their 20 years of exploration and mining of diamond placers on the Atlantic shelf of southern Africa, where they have also maintained a strong environmental record.   Glaciers and high-energy rivers emanating from the Southern Alps have transported substantial quantities of gold bearing sediment onto the Westland continental shelf during Pleistocene glacial periods, when fluvial gradients are steeper, sea level is c.120 m lower and most of the shelf is exposed. These deposits have been extensively reworked by the advancing shoreline and marine processes during interglacial marine transgressions, and most are now buried beneath a variable thickness of post-glacial marine sand, silt and mud. DBM will use side-scan sonar, swath bathymetry, Chirp sub-bottom profiling and a magnetometer to map the sea floor and sediments beneath it, guided by PSLÆs predictive geological model for gold distribution on the shelf. Cactus grab and vibro-core samples will be used to ground-truth the geophysics and provide stratigraphic, sedimentological and gold distribution data for incorporation into the geological model. Areas of interest identified by the geophysical and sampling data will be investigated in more detail, with closer-spaced geophysics and Mega-drill sampling to a maximum sediment depth of 20 m beneath the sea floor. These samples will be raised to the ship with air-lift suction technology, processed onboard for mineralogical and grade information, then returned to the sea floor. Environmental baseline data will be gathered from Van Veen grab samples of seabed sediment taken throughout the area during the prospecting programme.

Jan 1, 2005

By P Lindsay, J B. Hughes

Underground and opencast coal mining has been ongoing since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD are those of the Mangatini and St Patrick streams. These catchments flow into the Lower Ngakawau River, which holds high amenity value for the local community. Water quality targets set by Solid Energy for 2010 in the Ngakawau River include increased pH and clarity and a decrease in certain dissolved metals.   At-source ARD minimisation options are the first stage in mitigating the effects of mining acid forming rocks and reducing acid loads in the Mangatini and St Patrick stream catchments. ARD minimisation techniques reduce the quantity of acidity generated and thus reduces the treatment required. Treatment will be required for many years at Stockton due to current and historical acid formation. This paper looks at the treatment options that Solid Energy has been investigating including limestone leach beds, engineered wetlands, oxic limestone drains, and limestone dosing of catchment drainage. Particular focus is given to fine limestone dosing of the Mangatini stream and subsequent water quality improvements.

Jan 1, 2007

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010

Flotation of Smithsonite by Using Siloxane Cationic Surfactants as Collectors

Sep 13, 2010

Much of the coal and gold mining industry of New Zealand is small scale. Funding is tight and mechanisation limited. The country has many well documented small coalfields (some with significant outcropping) and alluvial gold deposits. These are generally remote, difficult to access (physically and otherwise) and of submarginal value (largely a consequence of size when viewed for extraction by traditional techniques). The industry is also burdened by environmental and bureaucratic constraints. The above over simplified setting suggests to the Author, a newcomer to New Zealand, the opportunity to consider some novel concepts based on technology and techniques developed overseas or borrowed from other industry sectors. The objective being to make viable in economic and environmental terms projects that might otherwise be stillborn if considered for exploitation by conventional means. The paper mainly discusses 2 concepts focusing on the application of augers for exposed high wall or outcrop coal and micro-tunnelling augers for alluvial gold extraction. These may be considered high mobility 'container' (as in shipping container) packaged, or 'non invasive' mining systems. It is stressed that these are but concepts and have yet to be subjected to rigorous financial or engineering scrutiny. This could only follow their acceptance by, and input from, New Zealand miners. There will also be brief mention of a new modular conveyor system which might have application within the concepts or existing small scale mineral extraction operations and mention of a project currently in progress to apply tangible 'sustainability' to underground coal mining.

Jan 1, 1996

By G Brooks

The control of phosphorus in steelmaking is one of the famous challenges of pyrometallurgy. It is well established that highly basic slags, the presence of FeO in the slag and lower temperatures (less than 1650°C) are favourable for phosphorous removal. The thermodynamics of this reaction have been extensively studied under laboratory conditions and the general trends confirmed through industrial trials. However, in general, phosphorus slag/metal distributions measured in industry are far from equilibrium and quite specific to the oxygen steelmaking technology being used. This variability was quantified by Urban, Weinberg and Cappel (2015), who found that the phosphorus partition ratio measured in plants varied with blowing practice, stirring intensity and even converter life. Some recent kinetic studies by Gu, Dogan and Coley (2017) have shown how the kinetics of these reactions vary with FeO content and dissolved sulfur at the droplet scale. A global kinetic model by Rout et al (2018) provides meaningful predictions of where dephosphorisation occurs in an industrial basic oxygen furnace (BOF) and some recent heat transfer modelling by Madhavan et al (2021, 2022) implies that temperature difference between droplets and slag has a role to play in explaining why equilibrium is not achieved. This paper will review the current state of knowledge and provide suggestions on predicting phosphorous removal for industrial operations and how greater removal could be achieved.

Jun 19, 2024