Search Documents

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

Rio Tinto Iron Ore (RTIO) manages eleven mines in the Pilbara region, Western Australia. Three of these mines have previously or are currently mining black shale that contains varying amounts of pyrite. Several new deposits currently being evaluated and existing mines that may progress below water table in the future, will also encounter this waste material. The black shale presents not just an acid rock drainage risk but also a spontaneous combustion risk. This paper presents the black shale management strategy and provides an overview of the relevant activities undertaken by RTIO. The strategy can be divided into two components which firstly involve defining the risk and secondly involve managing the risk. The mineral waste management plan is used to identify specific mineral waste hazards by:geochemical characterisation of waste material,undertaking mine site specific risk assessments,characterising the receiving environment,identifying sulfidic boundaries in geological and mining models,quantifying the amount of sulfidic material in medium and long-term mine plans, anddesigning and sequencing black shale waste dumps. Once a mine exposes black shale the Spontaneous Combustion and Acid Rock Drainage management plan is used and the major activities are: regular site meetings with a representative from every group that works with black shale;compliance with safe working procedures for site specific and detailed activities;regular training;the use of specific explosives to prevent premature detonation;ongoing geochemical characterisation;acid water management, monitoring and analysis;regular internal and external auditing of procedures and practices; andclosure planning assessments and preparations (ie cover trials, geochemical void modelling, geochemical waste dump modelling). The success of this holistic strategy is evident by the awareness of personnel within the business, thorough understanding of the geochemistry and by undertaking proactive management of black shale during mining. The strategy and management plans adopted by Rio Tinto Iron Ore have activities that other mine sites with potentially acid forming material may like to consider implementing.

Jan 1, 2009

By G Bubner, C Gaughan

Magnetite mineralisation within the South Middleback Range has been known since the early 1930s; however, it was not until 1989 that BHP (then owners of the Middleback Ranges mining leases) drilled 10 700 m of diamond core into what was then known as the Iron Duchess low-grade deposit. In 2002 a review of Iron Resources left in the Middleback Ranges and the identification of downstream processing benefits using magnetite as a primary feed source led to the commencement of an 18 000 m resource drilling program of the high-grade core of the Iron Duchess low-grade orebody (renamed the Iron Magnet deposit). This paper describes the geology, processes and procedures used since drilling recommenced in early 2003. The Iron Magnet deposit is located 53 km southwest of Whyalla in the South Middleback Range, South Australia. It is a Paleoproterozoic stratabound magnetite deposit that lies down-dip and lateral to the Iron Duke hematite deposit, hosted within the Lower Middleback Iron Formation of the Hutchison Group meta-sediments within the Cleve subdomain of the Gawler Craton. Magnetite bearing host units within the Lower Middleback Iron Formation can be divided into a æmixedÆ basal sequence, a lower iron carbonate unit, a middle iron talc unit and an upper iron silica unit, all units grading up sequence and laterally into one another. The magnetite mineralisation is hydrothermal in origin. The strongest consistent mineralisation coincides with the iron carbonate unit, and the hematite orebodies of the Iron Duke are interpreted to represent up-dip supergene enrichment of the same unit. The Iron Magnet occurs within a large-scale parasitic syncline-anticline pair on the west limb of a larger syncline. Major bounding north-south shear zones occur on the east and west sides of the deposit. Cross-cutting west-northwest, northwest, northeast and east-northeast trending faults displace mineralisation. The commencement of drilling in 2003 lead to the migration of geological and geochemical databases, re-logging and re-assaying of all old cores that intersected the deposit, updating of logging codes and procedures, and strict Qa/Qc procedures to ensure the study satisfied JORC standards. External consultants were used for auditing and bench marking. The strong geophysical responses of magnetite and the wealth of close spaced ground magnetic and gravity data already completed over the Middleback Ranges allowed for refining of drill hole targets for the drilling program. It also provided an indirect method for ascertaining magnetite grade and tonnage volumes.

Jan 1, 2005

By G Harbort

Traditional engineering design for flotation circuits use the “Rule of Thumb” approach. Typically this uses a nominated maximum head grade for design. A scale-up factor is applied to laboratory flotation tests for residence time. This scale-up factor is usually based on a designers experience at other flotation sites and may or may not be relevant to the circuit being designed, or the flotation equipment being used. A small number of locked cycle tests are assumed to represent the ore body and the results of these are often used for financial analysis, independent of changes in mine plan throughput and mineralogy.The engineering “Rule of Thumb” approach is only strictly accurate where there is very little variability in throughput, head grade and mineralogy. It may provide accurate design for mature established operations where a brownfield expansion is being considered but is unlikely to provide accurate design for a new, greenfield site.The use of geometallurgical modeling with floatability component simulation provides a design methodology with significantly less associated risk. The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to use spatial metallurgical information to drive production planning, mine planning, blast design, blending strategies and plant set-up. At a design stage the process designer can use geometallurgical information to evaluate bottle necks and potential design flaws and propose the best investment strategy for the project benefit.This paper details the geometallurgical characterisation of the Andash deposit and methodology used to review the project’s detail design and projected production.

Aug 8, 2011

By P Hawke, J Hurst, B KrapeP

Hancock Prospecting Pty Ltd (HPPL) drilled two deep diamond stratigraphic holes (ECD0001 and RHD0296) within the eastern Fortescue Valley in the Pilbara of Western Australia. Located south of the Roy Hill Iron Ore project, the holes aimed to define the stratigraphy of the Marra Mamba Iron Formation (MMIF) of the Chichester Range and its south-dipping extensions below recent cover. Previous attempts to define the MMIF of the Chichester Range have resulted in differing interpretations due to the data available at the time.The unweathered MMIF beneath the Fortescue Valley in the HPPL drill holes is characterised by dolomitic carbonate interbedded with stilpnomelane-rich shales, chert and banded iron formation (BIF) with hematite staining. This intersection equates to ~75 m of carbonate-facies iron formation, as opposed to the ~230 m thick oxide-facies BIF and shale sequence encountered south of the Fortescue Valley.Various detailed geological core analyses and interpretations from ECD0001 and RHD0296 were integrated with regional diamond and reverse circulation (RC) holes from across the Fortescue Valley. Interpretation of the data indicates that the eastern Fortescue Valley MMIF represents a thinned thickness sequence of the whole formation. The MMIF of the Chichester Range and Fortescue Valley has gamma logs that correlate strongly in parts to the type section used for MMIF south of the Fortescue Valley. Therefore, the outcropping MMIF in the Chichester Range represents an eroded equivalent of the æreducedÆ thickness MMIF observed in ECD0001 and RHD0296.Data from deep diamond drill holes across the valley, from the Hamersley Basin to the Carawine Basin, were correlated. The correlation shows that the depositional site of the MMIF in the HPPL diamond drill holes is consistent with a proximal ramp setting, in which iron-rich shales wedge up-palaeoslope and shelf-derived carbonate turbidites wedge down-palaeoslope. Not only is it the occurrence of these shales that define the MMIF, but they also determine the northward potential to develop orebodies, as they are the source of iron from which iron-rich oxides and carbonates of metamorphic or diagenetic origin form.CITATION:Hurst, J, KrapeP, B and Hawke, P, 2013. Stratigraphy of the Marra Mamba iron formation within the Chichester Range and its implications for iron ore genesis at Roy Hill - evidence from deep diamond drill holes within the East Fortescue Valley, in Proceedings Iron Ore 2013 , pp 91-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Ilmenite (FeTiO3) is the primary global source of titaniumdioxide which is commonly used as a whitening agent in papermanufacture and a pigment in paint manufacture. In WesternAustralia ilmenite is processed by the Becher process (Becher,1963, Becher et al, 1965) where ilmenite particles are feddirectly into the furnace with coal and heated to form acomposite of elemental iron and TiO2. The mechanism of thecarbothermic reduction of ilmenite has been extensively studied(Grey, Jones and Reid, 1973; Jones, 1973; Grey and Reid, 1974;El-Tawil, Morse and Francis, 1993) and is reasonably wellaccepted.

Jan 1, 1997

By M Sandy, P Bamford

The Challenger Gold deposit was discovered in 1995 by Dominion Mining Ltd in a remote western area of the Gawler Craton in South Australia. Mine development commenced in 2002 with initial production from an open pit supplemented by ore from a very small adjacent auxiliary pit. Development of the underground mine commenced in 2004. The orebody plunge of just less than 30 degrees requires careful attention to mine design. Production from the M1 orebody, with less than 800 ounces per vertical metre (ovm) and very limited æsurgeÆ capacity, requires careful scheduling and implementation to ensure continuity of ore feed for milling. Initial production results from underground stopes included more dilution than anticipated. The narrow, high-grade zones proved to have much more complex geometry than early interpretations had indicated. Greatly improved understanding of the mineralisation controls resulted in important changes being made to the underground mine design and method. Coupled with careful control of development and drilling and blasting practices, this resulted in an immediate reduction in dilution and high recoveries of the resource. The benefits of these changes flowed through in the 2005/06 financial year, resulting in a 150 per cent increase in gold production to 108 080 oz and a sharp reduction in cash operating costs to A$280/oz. This was followed in 2006/07 with production of 108 91 oz of gold at an operating cost of $309/oz and in 2007/08 with 109 326 oz of gold at $367/oz. Production to June 2008 has been mainly from the M1 orebody, with the lowest stoping to date on the 580 m Level (615 m below surface) above development mining on the 520 Level. The rate of vertical advance of mining this orebody has averaged 150 vertical metres per year. The increased current combined JORC compliant resource and reserve position of over one million ounces, now includes the M2 and M3 orebodies with a current total average gold inventory up to 1400 - 1500 ovm. Exploration has intersected other shoots and all shoots are open at depth. The adjacent M2 and M3 orebodies are being developed for stoping. The narrow width of these zones from 1 m up to 4 m will require continued focus on ore zone definition, accurate development and careful drill and blast practice. In addition, to minimise cost increases in the current period of rapidly escalating labour, equipment, consumables and energy costs, high productivities will need to be maintained to allow the established rapid mining advance to continue at low unit costs.

Jan 1, 2008

By A S. Derrington

High-accuracy, solid-state digital reference barometers have proven to be well suited to conducting underground barometric pressure surveys. The only problem is their expense; at least A$4000 each. For this reason, and because barometric pressure surveys are not a routine undertaking, very few mines have been able to justify the purchase of suitable instruments. The author knows of only three Australian metalliferous mines that own them.However, this may soon change given the recent development of low-cost, mass-produced miniature barometric pressure transducers. These transducers were developed to provide an altimeter function in the latest generation of smartphones. The main purpose of the inbuilt altimeter function is to allow the smartphone to be aware of its altitude when the global positioning system satellite signal is lost.This paper describes a prototype barometer that was constructed using one of the most accurate of the latest generation of piezo-resistive smartphone barometric pressure transducers. The prototype instrument was constructed for less than five per cent of the cost of a commercially available digital reference barometer. The prototype was subsequently tested against a reference barometer at the University of Queensland’s Experimental Mine to verify its accuracy and suitability for measuring pressure differences between underground survey stations.It is expected that the instrument’s low cost will pave the way for barometric pressure surveys to become more commonly used in mines. In turn, the resulting improvement in knowledge of major underground pressure losses should allow mine ventilation officers and engineers to optimise their ventilation systems and potentially reduce overall operating costs.An alternative option would be to use a barometer-equipped smartphone as a survey instrument, provided that its inbuilt barometer module is sufficiently accurate.CITATION:Derrington, A S, 2015. Development of a low-cost instrument for barometric pressure surveys, in Proceedings The Australian Mine Ventilation Conference, pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The selection and implementation of the right technology for a project is critical to the future development of the resource industry. It is essential for companies to ensure ongoing competitive viability that where practical new or alternative technology be adopted. Analysis of historical data relating to development of resource-based process plants provides an enlightening insight into the key factors which influence their success or failure. The adoption of new technology does not guarantee the success of a project. The outcomes of this analysis have been used to develop some general guidelines and principles the author believes are useful in the selection and implementation of new or alternative technology in resource projects. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Zani J. A, Jackson W. D

Bauxite was discovered in the Kimberley in 1965 by an Amax field crew. Reserves of 230 million tons, of bauxite. averaging 47% total alumina on Mitchell Plateau and 980 million tons averaging 36% total alumina on Cape Bougainville have been indicated by the results of drilling and bulk sampling. Laterite which contains the bauxite deposits caps basalt and interbedded sandstone and siltstone of the Carson Volcanics formation. Bauxite on Mitchell Plateau is 3.2 metres thick on average and is underlain successively by nodular ironstone, clay and basalt. The major components of the bauxite are gibbsite,boehmite, hematite and goethite containing some alumina, anatase and clay minerals. Quartz and vanadium oxide are minor constituents. Boehmite and hematite are concentrated near the surface, whereas gibbsite and goethite predominate at depth. The bauxite profile consists of ferru- ginous, pisolitic and gibbsitic zones with increasing depth. Cape Bougainville bauxite is 8.6 metres thick on average and of tubular structure; its mineralogy is relatively uniform..

Jan 1, 1973

By B L. Dickson, E, M F. Lee, P A. Mikula

Computational techniques are needed to assist in the analysis and interpretation of the increasing amounts of geoscientific and mining related data and information that are routinely gathered at mine sites. New interpretation methods are needed to provide an integrated approach so as to establish relationships (cause and effect) or to be predictive about possible outcomes based on acquired data. Traditional multivariate statistical methods are often confused by variable relationships that are non-linear, data distributions that are non-normal, and by the data themselves that may contain missing values, text and both continuous and discontinuous numeric values. Modern data mining methods are available to understand the relationships within and between diverse data sets, and identify relationships or trends associated with processes, measurements and mine design parameters in mines. The self-organizing map (SOM) is a data mining approach with the advantage that all input data samples are represented as vectors in a data-space defined by the observations (variables). The SOM procedure is an exploratory analysis tool that highlights patterns and relationships. Results are internally derived, in an unsupervised fashion based on measures of vector similarity. Our SOM outputs are highly visual, which assists in understanding and illustrating the dataÆs structure and internal relationships. Two studies are presented. The first uses SOM to investigate the relationships between a range of measured and derived rock property parameters and their observed behaviours during mining. Our aim was to determine whether a SOM analysis would allow a better understanding of observed and predicted rock behaviours from their rock properties. The SOM analysis showed that there were indeed relationships between æbrittleÆ, æsugaryÆ, æslabbyÆ and æsqueezingÆ rock behaviours and a number of the input parameters. The computed SOM æstructureÆ was then used to assess the likely behaviour of unknown samples by assigning them into behavioural fields based on their measured and derived geotechnical responses. The second study was aimed at assessing whether a SOM analysis of microseismic data at the Kalgoorlie Consolidated Gold MineÆs (KCGM) Mt Charlotte mine can contribute towards understanding and potentially forecasting/minimising seismicity at the mine-design stage. The database comprised 40 sample æclustersÆ of microseismic parameters from the MS-RAP software package, which were derived from 2500 individual seismic events. The SOM analysis showed that some of the initial mining conditions are related to the seismic parameters. In each of the studies, the SOM procedures assisted in understanding the data and provided new insights. Because of its æordered vector quantisationÆ foundation, the SOM procedure is a substantial improvement over traditional statistical methods in three main areas:its ability to analyse data from disparate sources, including different data types; its ability to analyse sparse data sets with missing values; and its ability to analyse and visualise non-linear relationships within a data set.

Jan 1, 2006

By R Witt, M Lowing

Tanking of tunnels is now often specified when inflows exceed as little as 1 L/s/km with a unit distance of 100 m. To demonstrate inflows over a 100 m segment of a tunnel are less than 0.1 L/s with a standard error of 0.01 L/s by timed, gravity filled, volume measurement up and downstream of the segment, the measuring cylinder volume (L) must exceed 10 Q, where Q is the flow in L/s, and the number measurements taken and averaged must exceed 20 . If a standard error of 0.02 L/s is acceptable then 5Q2 measurements must be taken and averaged. If gravity filling is not possible then the number, n, of repeat pumped container measurement required is given by: where: is the 100 m section leakage is the volume filling time is the standard error of volume measurementZ is the standard normal variateK is a coefficient dependent on physical measurement conditions Based on analysis of field data an indicative coefficient of variation of volume measurement is ~0.05.

Jan 1, 2008

This paper outlines the advances made in vacuum filtration as developed by Outomec Process Filters and details the results obtained at a number of Australian installations. The first section of the paper details the technical advances made by the use of ceramic media in vacuum filtration and explains the reasons for the use of the technology. The second part of the paper discusses a number of Australian installations of the ceramic vacuum filter and where possible compares the actual experiences with those predicted from the test work which preceded the installations. The Ceramec Capillary Vacuum Filter is a vacuum disc filter which combines the proven mechanical attributes of a disc filter with exciting new ceramic vacuum technology from Outomec of Finland.

Jan 1, 1991

By Robertson AC

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authors' personal observations and experience.

Jan 1, 1998

By B Flynn, P Knights

Low-loaders or 'floats' for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By F Rashidinejad

Iran has had an active mining sector for some 7000 years. Exceptional in terms of its mineral diversity, Iran produces 62 minerals, and is ranked among the world’s 15 most mineral-rich countries. Many people around the world know Iran as one of the major petroleum exporters. Oil and natural gas dominate Iran’s economy, and oil exports provide the principal source of income, contributing more than 80 per cent of foreign exchange earnings. Transformation of Iran from an oil exporter to an independent country to oil has been on the table for many years, even before the Islamic Revolution of 1979. Development of the Iran’s mineral industry is one of the major replacements for petroleum exports. In the last decade, Iran invested billion dollars in the mining and mineral industry sectors and to increase the added value, tried to export processed minerals instead of the raw materials. In accordance with the ‘20-year Perspective 2025’ that targeted by the Supreme Leader, Iran will be a country with the first rank in economy, science and technology in its region. The objectives over this perspective include briefly increasing annual production to 55 Mt of crude steel, 800 000 tonne of copper cathode, 1.5 Mt of aluminium, 200 Mt mineral products, 300 000 tonne of zinc and 5 000 kg of gold. These goals are achievable in normal circumstances, but concurrency of the 20-year Perspective 2025 with commencement of the UN Security Council sanctions against Iran, frustrated objectives of the perspective, at least the ones related to the mining and mineral industry sectors. This paper tries to elaborate the development programs and following challenges for the mining activities of Iran by 2025.

Nov 22, 2011

By P J. Clark, A W. Fisher, R G. Ford

Site characterisation of subsurface contaminant transport is often hampered by a lack of knowledge of site heterogeneity and temporal variations in hydrogeochemistry. The use of a regional-scale data compilation derived from satellite imaging is discussed with respect to directing design of site characterisation to monitor the fate of a Dense Non-Aqueous Phase Liquid (DNAPL) plume in Nevada. Evaluation of the drainage basin contributing to the groundwater flux into the study site was used to re-assess the site conceptual model and re-direct the characterisation effort. The use of highly resolved measurements of subsurface hydrogeochemistry in space and time were employed to identify the predominant biogeochemical processes controlling arsenic transport during discharge of groundwater into a pond at a site in Massachusetts. Direct-push conductivity measurements coupled with vertically-resolved sampling within the pond and adjoining aquifer demonstrated spatial and temporal variations in dissolved arsenic within groundwater and the pond water column and sediment pore water. Spatial variability was observed over the scale of centimetres to metres, and temporal variations were observed over the scales of days (following storm events) to seasons. Microbially-driven redox processes maintained anoxic conditions in groundwater and at the sediment-water interface (iron and sulfate reduction) and exerted both a direct and indirect influence on arsenic solution speciation and partitioning to surface water sediments.

Jan 1, 2004

By L S. Shekhawat, M P. Roy, R K. Paswan, P K. Singh, A Joshi

Blasting in the mining industry is being transformed, and can no longer be treated as an art or a practice purely dependent upon experiences of individuals. Examples of key drivers that have demanded consistent and more accurate blast results are initiatives to control pit-wall damage to help mine steeper pit slope angles, to control damage to underground opening operating in close vicinity of the open pit mine. Such situation exists at Rampura Agucha open pit lead zinc mine, which is producing 5.7 Mt/a of ore and has started its underground part, which is slated to produce initially 2–2.4 Mt/a and 4.5 Mt/a in the near future. The open pit mine is currently working at 326 m depth and is designed to reach 421 m deep. It has been planned to operate the underground mine maintaining 50 m parting from the planned ultimate level of the open pit mine.Presently, open pit and underground mines are being operated simultaneously. The present average depth of underground working lies between 370 and 410 m below the surface level. Sometimes explosives up to 95 978 kg are being detonated in a blast round in open pit mine. These blasts are often apprehended as a danger to the safety and stability of underground openings. It was decided to document the impact of open pit blasting in the openings of underground workings, so that preventive measures may be taken for the safety and long-term stability of the underground mine. The impact of 86 open pit blasts has been documented in the underground openings and 258 blast vibration data has been recorded. The vibrations were recorded simultaneously in the roof, side walls and at floor levels. The highest levels of vibrations were recorded in the roof and the lowest levels at the corresponding floor levels. The pillars experienced lower level of vibrations than the roof. Blast designs were optimised at open pit mine to control vibration in view of long-term safety and stability of the underground openings. The vibrations generated due to detonation of explosives with shock tubes and electronic delay detonators have been recorded in underground openings for comparative assessment. Ground vibration recorded at roof, pillar and floor were analysed separately and threshold value of the vibration for the safety of underground workings has been determined based on the rock mass rating of the roof rock.CITATION:Singh, P K, Roy, M P, Paswan, R K, Shekhawat, L S and Joshi, A, 2015. Protection of underground mine structures due to adjoining open pit mine blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 279–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Dunbar, S Harrison, J Cilliers

‘Those who cannot remember the past are condemned to repeat it.’George Santayana (16 December 1863 in Madrid, Spain to 26 September 1952 in Rome, Italy). Philosopher, essayist, poet and novelist.The minerals industry requires specific technical expertise in mining and mineral process engineering, geoscience, environmental science and social sciences to maintain and operate its current business and to develop future projects. A steady supply of new graduates is essential to replace not only retirees, but also those who left the industry during the recent downturn. The supply of trained graduates is however not instantaneous, and there is a four-year lag from entry into university to graduation. It is essential that this lag in human resource supply and a likely shortage of knowledgeable, qualified talent is taken into account when considering risks to the business of mining. The shortage of skilled professionals has in the past resulted in unsustainable salary expectations and is likely to pose financial and execution risk to new projects. This paper will review some recent statistics of students in training from around the world and explore what action is required to not only sustain the training courses that provide future ready talent to the mining industry, but also ensure that graduates from these courses are equipped to create change and be leaders in the industry. The future prosperity of the industry is dependent on delivering sustainable stakeholder returns through the cycle. This will be achieved by developing capable individuals that can respond to the complex, adaptive challenges facing the industry.*This is an abstract only. No full paper was prepared for this abstract.*CITATION:Plint, N, Cilliers, J, Dunbar, S and Harrison, S, 2018. Back to basics: resourcing the mining industry, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 33–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011