Search Documents

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By K S. Park, J K. Kim, J H. Park, Y Su

The present study investigates the possibility of the direct removal of oxygen from the Ti-30Ni (wt per cent) alloy melt through the thermodynamic equilibrium reactions at 1623 K in the vertical tube furnace. The deoxidation efficiency of Ti-Ni alloy melt by adding different contents of metallic calcium (Ca) as a deoxidant was evaluated with the binary CaF2-MgCl2 flux. The thermodynamic equilibrium experiments showed that the total oxygen content in the alloy decreased from about 650 ppm to 350 ppm when 3.5 wt per cent Ca was added to the Ti-30Ni (wt per cent) alloy. Alternatively, the effect of flux composition in the CaF2-MgCl2 flux on the oxygen content was also investigated at 1623 K. Therefore, the effect of binary flux systems on the deoxidation ability was compared at 1623 K. According to the results, the flux system with 80 per centCaF2– 20 per centMgCl2 exhibited the best deoxidation capability, ie total oxygen content in the alloy reduced from 1450 to 550 ppm.

Aug 21, 2024

By E Jamieson

For a number of years, Alcoa World Alumina Australia (Alcoa) has been investigating opportunities to produce economically viable products from bauxite residues. Three of these potential products are described here, being Red Sand, ALKALOAM« and REDLIMETM.Red Sand has a nominal particle size of +100 micron and is physically little different to crushed bauxite from which it is derived. In AlcoaÆs Western Australian refineries, Red Sand constitutes up to half of the residue going to impoundment areas. Initial testing indicates that this sand could be processed to provide an acceptable general landfill material, a construction back fill or a material suitable for road base construction. ALKALOAM« is the fine-grained residue often referred to as red mud. A great deal of work has been done to show the benefits of adding this material to sandy soils, which are common in coastal regions of WA. ALKALOAM« has properties that can elevate the pH of the acidic soils and also retain phosphorous, reducing overall fertiliser use and protecting sensitive waterways. REDLIMETM is a by-product of the refining process. This material has a high acid neutralising value. REDLIMETM could be more effective at pH control than most available products because of the fine particle size and sodium carbonate that remains with the product.

Jan 1, 2004

The Kaltails Project is situated close to the city of Kalgoorlie-Boulder in Western Australia. Located on the south-eastern fringe of the Golden Mile, Kaltails has been in operation since June 1989. The tailings forming the reserve for Kaltails have been derived from 100 years of underground mining on the Golden Mile, but, some of the re.;erve has been retreated in the past. A map of the tailings reserves and treatment plant site is presented as Figure 1. The gold project is a joint venture between Poseidon 90 per cent and Gold Corporation (ten per cent) and is managed by Poseidon Gold Kaltails.

Jan 1, 1992

By M Andrew, H Reynolds, R Mills

As the global mining industry continues to grapple with ‘black swans’ (high consequence / low frequency events) for health, safety and environmental losses, the focus is shifting from risk assessment of these events to risk management using selected purposeful controls that reduce the risk.Fundamental to critical control management (CCM) is a soundly based rationale for selecting the right controls for each and every risk. The approach should be based on a thorough understanding of the dynamics of the event: What causes it? How frequently will it occur? How likely is the consequence to be realised? This is typically done through a bowtie and methodical numerical risk analysis. Core to this step, then, is the structure and content of the bowtie; specifically, the analytic architecture that is used to construct the bowtie. Different architectures yield different constructions, and bowties are no different.Although bowties for operational health and safety (OHS) hazards appear to have a common architecture, they are not generic. It is important to stress that they contain site specific information, are prepared by site based operational teams, and vary from site to site to reflect each site’s operational conditions. They are often a product of the knowledge and understanding of the operational teams involved, may be prone to human error, and potentially miss latent hazards that may have been embedded early in the planning, design or construction phase of a mine or facility, or within the mining equipment. Overcoming these deficiencies through constant re-evaluation of the risks, and challenging the content on the bowtie will help to minimise the chance that something will be missed.This paper will cover key themes in bowtie architecture, introduce the concept of barrier models for high consequence event (HCE) bowties and present a relevant case study to illustrate the issues that determine quality in bowtie construction and critical control (barrier) selection and management.CITATION:Mills, R, Andrew, M and Reynolds, H, 2016. Can we stop a black swan breeding? Advances in bowties and critical control management, in Proceedings International Mine Management Conference, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

No paper available.

Jan 1, 1996

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

By K Williams, G M. Evans, S M. Iveson, K P. Galvin, C E. Loo

The Australian Research Council (ARC) has recently established an Industrial Transformation Research Hub in the area of iron ore, focused on iron ore characterisation, beneficiation, materials handling and end-use functionality. The research hubs are part of a new initiative aimed at building stronger relationships between industry and universities, while addressing issues of national significance. The ARC Research Hub for Advanced Technologies for Australian Iron Ore will focus its attention on developing innovative approaches for creating enhanced value across the full value chain through the characterisation of different ore types, beneficiation and materials handling and transport. This hub brings together five industrial organisations and a research team formed from well-established research groups based at the Newcastle Institute for Energy and Resources. These groups have a record of working closely with industry to create opportunities. Examples include new beneficiation technologies such as the Reflux Classifier for achieving gravity separation, the expertise of TUNRA Bulk Solids in materials handling and the Iron Making Centre at Newcastle, which is a capability maintained by BHP Billiton following the closure of its Technology Centre in 2009. The purpose of this paper is to provide an outline of the research hub and its objectives, some background on the research groups that now form the hub and an insight into the strategy adopted for developing and implementing new technologies. The paper also describes a range of novel technologies that have the potential to be developed and applied to iron ore beneficiation.CITATION:Galvin, K P, Roberts, A, Loo, C E, Evans, G M, Williams, K and Iveson, S M, 2015. Australian Research Council research hub for advanced technologies for Australian iron ore – an introduction, in Proceedings Iron Ore 2015, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By K Sanematsu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore deposits of rare earth elements (REE) in South-East Asia are classified into four types: carbonatite, allanite, ion-adsorption and placer. Occurrences of the carbonatite deposits are confined almost exclusively to the Red River Fault Zone of northern Vietnam. Since the carbonatites contain dominantly REE fluorocarbonates (eg bastnasite) and lesser amounts of monazite, they are rich in light REE but poor in heavy REE. The ion-adsorption type deposits and prospects were found in Myanmar, Vietnam and Thailand. The ion-adsorption ores generally show lower REE grades than those of the carbonatite type and placer deposits; however, they could be enriched in HREE, which are more precious and scarce commodities than LREE. The ores consist of weathered granites with a significant amount of ion-exchangeable REE, which are extracted by using a dilute electrolyte solution. The ion-exchangeable REE are likely to be sourced from REE fluorocarbonates, allanite and titanite because these minerals are relatively susceptible to weathering and release REE3+ ions into soil water. In contrast, monazite and xenotime are resistant to chemical weathering and could form placer ores. Placer monazite and xenotime have been processed as by-products of placer Sn, Zr or Ti in Malaysia, Thailand and Indonesia, although the current production is small.CITATION:Sanematsu, K, 2015. Rare earth element deposits and prospective areas in South-East Asia, in Proceedings PACRIM 2015 Congress, pp 671–678 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Research Centres Program initiated by the Federal Government and supported by the mining industry has had a major impact on geoscience research and education during the past five years. Eight major university based-Geoscience Research Centres are currently supported by the Government, including four Key Centres of Teaching and Research and a further four Cooperative Research Centres (CRCs). The Research Centres Program has led to a concentration of high quality research and teaching in areas of demand and strategic importance creating strong university - industry linkages and a source of well trained and motivated graduates. Over the last decade Australia's reputation as a leader in mineral exploration and ore deposit research has grown substantially, in part because of the development of the Research Centres Program, and to increased collaboration and interaction between research groups and exploration geoscientists across the industry. During a period when ore deposit research activity has been decreasing in other countries (eg USA, Canada, Japan and most European countries), equivalent research activities in Australia have been increasing, within a well co-ordinated national framework. The future challenge for universities and the mining industry will be to maintain the momentum of the successful research centres in order for the centres to become self-funding over a six- to nine-year period.

Jan 1, 1996

By Armstrong A

Queensland is Australia's second largest mining state with world-class deposits of coal, base metals, bauxite and magnesite. The total value of Queensland's mining production is about $5 billion per annum, and coal accounts for around 55 per cent of that total. The environmental issues which arise as part of management and regulation of the industry are resolved within the EMOS process. The Environmental Management Overview Strategy is the cornerstone of the policy 'Environmental Management for Mining in Queensland' developed jointly by the Queensland Department of Minerals and Energy and the mining industry. The Gordonstone Coal Mine is the largest underground mine to gain approval under the new policy. Accordingly, Gordonstone has a well planned environmental management program which takes into account site-specific factors and provides for continuous compliance with the provisions of the Mineral Resources Act in a self-regulatory context.

Jan 1, 1994

By S Saydam

Professional engineers need to be able to apply university learning to practice. In particular, they have to take responsibility for interactions between technical systems and the complex social environments in which they operate. The most effective way of building this competency is through active experiential learning. We have been developing an advanced educational integrated simulation system to provide mining engineering students with an interactive and immersive learning experience that is not otherwise possible. This will give students an authentic experience in working with industry software packages, while also contextualising the learning in terms of the broader and longer-term impact of technical decisions. We have been piloting the system, in undergraduate courses in order to establish its effectiveness in building systems thinking competencies for mining engineering. For postgraduate students and professionals, the same tools and methods can support studies of more challenging and complex scenarios where mining engineers have to place their decisions within complex global industry contexts.

Nov 22, 2011

By I Jabou, D G. Blazak, L C. S Hogarth

The R70 test is a good indicator of coal reactivity to oxygen and is commonly used to provide a rating of propensity for self-heating. Tests performed by The University of Queensland Spontaneous Combustion Testing Laboratory have resulted in the development of a large database that shows the impact of coal quality on this parameter. From these results it is possible to infer an R70 value, which can be used to gain an appreciation of the intrinsic coal reactivity before it is even tested. However, any interpretation of R70 values must consider the influences of coal rank, mineral matter and moisture content to provide a better understanding of the spontaneous combustion risk of a particular coal.

Jan 1, 2005

By R Billingham

QueenslandÆs new safety legislation for metalliferous and coal mining (Mining and Quarrying Safety and Health Act 1999 and Coal Mining Safety and Health Act 1999, together with the Regulations) came into effect on 16 March 2001. The legislation places clear obligations on mine owners, operators and workers to have a safe place of work and to manage risks to safety and health. It also places obligations on contractors, designers and providers of services. The legislation is non-prescriptive in that it states what outcomes must be achieved and not what must be done. The key issue is that the risk of injury to people must be at an acceptable level. The legislation creates a Mines Inspectorate with powers of inspection and audit of mines, their safety management systems and the management of risks. Auditing of the risk management process is carried out against standard risk management techniques and directives for corrective action may be issued when audits reveal non-compliance or unacceptable levels of risk.

Jan 1, 2002

In terms of tunnelling the mining industry is generally thought of as the crude cousin of the civil construction industry. Mining has tended to concentrate on speed and flexibility rather than the high standards required in civil tunnelling. Historically this difference has been based on the belief that such high standards were not required by the mining industry, they would slow down the development of the project and as a result increase the costs and extend the time period between start up and a positive cashflow.For civil works the construction of a tunnel is the project, for mining the construction of declines, crosscuts and drives are merely the means of accessing the orebody so that the real work can begin û MINING. Extraction of ore is the core business of most mining companies û it is what pays the bills.Though most mining companies have the equipment, the people, the knowledge and the ability to excavate tunnels, in the past mining companies did not appear to put the same energy into their tunnelling operations as they put into improving their ore extraction operations. In the past decade this appears to have changed, many mining companies now realise how important the correct excavation of a decline is to the success of the overall mining operation. They began to recognise that there were cost benefits to be gained in using the correct development techniques without overly sacrificing the benefits of speed and flexibility.This recognition also coincided with the growth of underground contractors whose predominant work was primary development (declines and ore access crosscuts and drives). The contractors again had the same knowledge, the same people, and similar equipment but their focus was different from that of the mining company û the contractors were focused on the development of the mine, the excavation of declines, crosscuts and drives. These deliverables were the contractorsÆ core business û itÆs what paid the bills.

Jan 1, 1999

By P Aspinall

Safe work Australia (SWA) has a number of proposed amendments to existing Workplace Exposure Standard (WES) values that may dramatically change how mining workplaces using personal gas monitoring instruments will operate. In consultation with leading gas monitor manufacturers and distributors, an assessment of common Australian alarm settings values and analysis of potential frequency of increased alarm likelihoods has been conducted. This assessment explores the relationships between current monitoring practices, using instruments as health and not just safety tools and identify what will be needed to minimise worker ‘alarm fatigue’ and for common tasks to continue safely. This paper provides the necessary information to aid industry and hygienists to be ‘future ready’ given the likely impact that order of magnitude reductions in time weighted average (TWA) values for NO2, SO2, H2S and other common gases will have on current working practices. Reductions to gas alarm values will provide significant challenges to existing work methods and will require, practical application of the pending future values. Improvements and awareness of instrument capabilities by safety and hygiene professionals will better utilise gas monitors real-time data monitoring capacity and no longer be just ‘safe or not-safe’ instruments. The presentation seeks to promote the practical steps required in setting alarms based on risk consequence and likelihood, increase general awareness of the tools and data available in modern instruments and will enable industry professionals to better manage the challenges of any potential future changes.

Apr 16, 2024

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

Our modern cities are almost incapable of sustaining themselves without subsurface infrastructure, which is not identifiable at first glance. This very soon becomes evident when the chaotic conditions prevailing in some cases in the multi-million cities on the African, Asian and South American continents are taken into consideration. This does not simply apply to the hopelessly congested streets in the downtown areas. If anything, it is shown here too that a subsurface infrastructure represents an important prerequisite for public health right up to banishing the danger of disease. Even during the 1990s, this has been clearly underlined through examples of cholera and plague epidemics in parts of Central and South America as well as on the Indian subcontinent. The overriding significance of an inner urban subsurface infrastructure in order to create decent conditions in the major built-up areas was once again emphasised not all that long ago at the United Nations HABITAT-II Conference in Istanbul, Turkey, in June 1996. More than 15 000 delegates from all over the world mulled over and discussed the prerequisites for humane living conditions in human settlements taking the varying climatic, topographical and cultural marginal conditions in different regions of the globe into account. Apart from the built-up areas themselves, the utilisation of underground space is experiencing high and ever increasing significance in less densely populated regions. Attractive and fast transport links between industrial centres call for high- performance transport arteries for the economic, speedy and unhampered carriage of people and goods. Important impulses for the economic power of a region or nation are provided by transport development and links. As a consequence, tunnels for roads and railways are being built or planned to a great degree for crossing mountain ranges, rivers and straits.

Jan 1, 1999