Search Documents

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By Collins DN, Hollick CT

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed in which such minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95% have been achieved and with coarse ores over 80%,in both cases at high grade. Several flotation regimes have proven effective. The potential for generation of radioactive dust or product contamination is subsequent processing -is correspondingly reduced.

Jan 1, 1990

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By P J. Willems, B J. Junor

Blackwater Mine is in the central-southern Bowen Basin, immediately south of the township of Blackwater on the Capricorn Highway. The current open cut operation extracts coal from three main seams, designated Top, Middle and Lower, in the Late Permian Rangal Coal Measures cropping out on the eastern flank of the Comet Ridge. Complex geological structures, dominated by E-W normal faults and N-S reverse faults, have significant detrimental effects on coal mining operations. Historical exploration before 2010 involved several types of drilling only to understand structure, coal quality and washability. Hence, although drilling data was combined with limited pit mapping and observation, unknown structures were still often encountered during excavations and led to mining surprises. In 2010 BHP completed 200-line km of closely spaced 2D seismic survey to capture gross and detailed structures followed by fit for purpose structural drilling to confirm major structures in the northern part of the mine. In 2018 a high density 9.2 km2 3D seismic survey was completed in the southern part of the mine. Subsequently, a 17.2 km2 survey was completed in 2020 to cover the northern active mining area. It allowed geoscientists to successfully map previously unknown major faults and seam splits, which could potentially impact the mineability of the area. It is important to note, that faults interpreted using modern high-density 3D data can be interpreted with dramatically higher confidence in the fault dip and azimuth orientation in comparison to the legacy 2D data. Along with targeted drilling, pit mapping and structural interpretation, the outcome adds value to mine planning and operations. This paper outlines recent successful seismic 3D data acquisition and interpretation. In detail, the paper presents case studies on how the data can be incorporated into a structural model to improve geological knowledge, enable geotechnical assessment, and support safe and efficient coal mining in a large and structurally complex mine.

Mar 22, 2022

By M L, G Maddocks, A Ferrier, ers, A Forbes

Evolution’s Mount Rawdon Operation (MRO) produces gold and silver through open pit mining methods. The mining operations are scheduled to be completed in FY24 (Financial Year 2024), after which low-grade stockpiles will be processed until the end of FY27. As part of MRO’s Progressive Rehabilitation and Closure Plan (PRCP), RGS Environmental Consultants (RGS) and Deswik were engaged to develop the final landform surface and a whole of site probabilistic water balance/water quality (WB/WQ) model to evaluate the viability of several closure options with respect to water quality in the various site water storages, particularly the final void which will form a pit lake. This case study details the closure option which included (amongst other things) covering the final landforms and directing water toward or away from the final void post closure. Closure and rehabilitation for MRO had previously been planned and evaluated on a ‘domain’ basis. Furthermore, the rehabilitation plans and final water management plans for the Tailings Storage Facility (TSF), Waste Rock Storage Facility (WRSF) and other domains were not coordinated, possibly resulting in competitive rehabilitation material requirements at the commencement of closure activities. An assumption was that a legacy non-acid forming (NAF) stockpile would provide sufficient material to both supplement ex-pit material for the construction of the TSF embankment raises and to complete all closure activities, but the volumes available and the volumes required to complete the closure activities had not been quantified.

Aug 2, 2023

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Kent, D Elder, J Woodward, R Edwards, B Catto

At Tropicana gold mine (TGM), mine planning is completed from ‘one source of truth’ known as the Integrated Planning Model (IPM). The IPM is a block model which forms a core component of the TGM Mine Planning System – used for short, medium and long-term mine planning cycles, and for Mine to Mill reconciliation.The IPM was developed from a desire to consolidate long-term information contained in mineral resource and ore reserve models, with short-term information from the grade control processes, including grade control models and ore polygons.The IPM is informed initially by resource models, upon which the longer term budget and schedules are based. The IPM is routinely updated with grade control models and ore design information, providing increased confidence for short to medium term mine planning. In this format, the IPM also provides a framework for reconciliation of resource performance with grade control, mining actuals and mining schedules, and ultimately milling. As well as a means for analysing past performance through reconciliation, it has proven its worth as a predictor of variation and an input to successful schedule sequencing and change management. The IPM is a critical component of the TGM Mine Planning System, providing a centralised framework for short interval mill feed prediction through to life-of-mine (LOM) planning.Current development of the IPM is working towards incorporating Mine to Mill optimisation and real-time material tracking projects at TGM. If successful, the model will provide a truly powerful mine planning data source. Current development outlines a mechanism for tracking material from Mine to Mill, and for transferring mill performance data back to the IPM. Increasingly advanced material classification and mine planning, incorporating the multiple geometallurgical variables, will enable the mine to provide consistent mill feed products and result in a steady state and optimised mill.This paper outlines the vision, creation and benefits of the IPM at TGM. It also introduces the ongoing developments to ensure the IPM becomes only more relevant to successful and integrated mine planning as TGM matures from the new kid on the block to the old hand in the neighbourhood.CITATION:Catto, B, Elder, D, Edwards, R, Kent, M and Woodward, J, 2017. An integrated approach to mine planning – building the integrated planning model at Tropicana gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By G Cooper

The Société Nationale Industriel et Minière (SNIM) is expanding its ore and concentrate production capacity in Mauritania, West Africa. This government-controlled mining company has been in production since 1963 and currently exports some 12 Mt/a.SNIM is presently doubling its magnetite concentrate production at the Guelb el Rhein mine. An existing processing line will have a second parallel production line of 4 Mt/a added. The mine is located some 600 km inland from the Atlantic coast in the heart of the Sahara Desert.The metallurgy of the ore is reasonably straightforward. It is a magnetite banded iron formation that is amenable to magnetic separation. While the existing plant uses semi-autogenous grinding and dry magnetic separation, the new processing line will use HPGRs, dry magnetic separation, and a wet milling and magnetic separation circuit for treating middlings.The process choices refl ect the scarcity of water in the region, the high cost of locally generated power and the operating experience and preferences of SNIM. Dust control in the desert environment has been a particular challenge.The metallurgical design aspects as well as the infl uence of the environmental and commercial aspects of the project are presented.

Jul 11, 2011

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022

By R Wynn, T J. Akroyd, C Costa

In an environment of lower zinc prices, falling revenues and reducing zinc feed grades, Century mine implemented a fast-tracked capital upgrade program in less than 15 months. The program was designed to increase ore milling throughput capacity by 20 per cent and optimise the capacity of the flotation plant to increase zinc recovery by approximately 2.5 per cent whilst maintaining final zinc concentrate grade.A key aspect of this program was minimising capital expenditure by better utilising existing capacity and only adding capacity where absolutely required to address critical processing bottlenecks. By gaining an understanding of plant process bottlenecks and future ore blends, and by carefully selecting appropriate technologies for particular specific flotation applications, maximum return on minimal capital investment was achieved.The close collaborative work achieved between the metallurgy processing department and other operational departments on-site was also critical to the success of this project. This work increased the mining and processing capacity of the mine and port site respectively, such that the full value of the process plant modification could be achieved.Capital payback on this investment was achieved in approximately three and a half months.This case study demonstrates the extra value to a mining business that can be achieved through fully understanding the mining/processing value chain and by careful targeted action to address critical bottlenecks in the processing chain from the mine through to the port site.CITATION:Akroyd, T J, Wynn, R and Costa, C, 2014. MMG Century Mine, a case study – maximising project net present value through targeted capital expenditure and process optimisation against a backdrop of falling metal prices and feed grades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 417–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M S. Tuohy

Since the independent review of fatal accidents in the mining industry carried out by Dr Sean Brady (the ‘Brady Review’), High Reliability Organisations (HROs) and their operating principles have been discussed across the Queensland mining sector. HROs are organisations said to consistently avoid serious failures, reliably delivering their organisational objectives despite operating in environments characterised by high levels of inherent risk and/or operational complexity. HRO concepts have previously found application in other similarly hazardous industries to mining. However, as Hopkins (2009) pointed out, HROs ‘are very elusive creatures that inhabit the realm of theory more than the real world’. The Queensland Resources Council (QRC) with support from the Commissioner for Resources Safety and Health initiated a review of how HRO principles can be translated to the mining industry. The review was conducted by Noetic, an Australian management consulting company that specialises in hazardous industries, including mining and metals, and has prior experience applying HRO theory.

May 5, 2022

By M Rafty, C Lane

Managing water is a key aspect of mining, whether a site is in water surplus or water deficit. Water in tailings storage facilities (TSFs) needs to be managed carefully to maximise the density of the solids, maximise the re-use of available water and to minimise the risk of water overtopping the spillway in the event of heavy rainfall. Developing a water balance models is a standard method for monitoring the major flows of water around a site. However, models created by specialist consultants are often overly complex and are not suited to being used by process plant personnel after they have been handed over to the mine operator. Models typically offer information on water management at the time that they are created, but then ‘sit on the shelf’ and offer no further insight or value for operating mines. Advisian has developed a customised water balance model for a mine in Sub-Saharan Africa, which can be adapted to other locations, to assist in managing water at the site and in particular to predict the current and future water level and volume in the TSF under various rainfall scenarios. The model was developed using Microsoft Excel and requires no specialist skills to operate. Site personnel enter in daily production, water transfer and rainfall data and then view the output dashboards to observe the current water level and volume, decant rates, licensed water abstraction and water supply versus demand. The output dashboards were developed in close consultation with the client to ensure that all of the relevant key performance indicators were included, from the perspectives of all the key stakeholders. This modelling approach focusses on the needs of the people who will actually use the model to actively manage TSFs with the need to involve the model developer as part of ongoing operations eliminated. The simplicity of this approach is now being embraced by other mine sites in Africa and Australia. CITATION:Rafty, M and Lane, C, 2018. Water balance management 101, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 485–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By O Bascur, A Soudek

Large metallurgical complexes are substantial users of energy, water and assets. To improve the effectiveness of energy and assets the quality of the data and events become paramount for real-time operational management. A lack of resources at the local operations and at the enterprise makes it impossible to process the sea of information and many projects have failed. As such, a novel approach for implementation of continuous improvements at the local level and innovations at the strategic level was implemented at all operating plants at Anglo American Platinum. Sixteen concentrators, three smelters and two refinery process systems were integrated to scale the information for manufacturing services at the local and enterprise level. The new capability of an enterprise real-time monitoring and diagnosis software infrastructure was available to implement many business strategies in tandem. Mineral and metallurgical processing knowledge is used to simplify the implementation of the data model. As such, asset monitoring, energy, production and process control management were implemented in an integrated approach reusing the same data but with different context and time horizons to have a standard methodology for local root cause analysis. This paper will highlight a sustainability management approach to change and empower the local and strategic team to collaborate using a new approach for adaptive reporting and condition-based event management and notifications. The results based on the integrated and collaborative team efforts will be presented. OSIsoft Plant Information system was installed and configured to achieve a targeted reduction in energy consumption of 15 per cent by 2015.CITATION:Bascur, O and Soudek, A, 2014. Implementation strategies for energy effectiveness and sustainability – example of Anglo American Platinum, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Stipcevich, N Patel, J Faithful5, S Narendranathan, L Tatnell4

ENGIE, the current owner and operator of the Hazelwood Open Cut coalmine, are in the process of rehabilitating the mine site in preparation for mine closure. Bucket wheel excavators (dredgers) used during coal mining operations are in the process of being demolished, which involves the controlled felling of dredger components using explosives. With the mine located in close proximity to the Morwell township and other critical public infrastructure, it is crucial that the use of explosives and the possible implications for mine stability is well understood. The felling of Large Mining Equipment (LME) will apply an impact load immediately to the underlying coal benches with the adjacent coal batters potentially at risk also of adverse slope stability impacts. This paper presents the 3D stability modelling methods employed to successfully assess the potentially adverse stability implications associated with LME collapse.

Jun 21, 2022

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010