Search Documents

By Beer G

The recent re-emergence of an Integral Pressure Stripping system which operates with both cell and column in closed circuit at elevated temperature and pressure, requires no cyanide in the eluate solution and has greatly reduced carbon reactivation requirements in seen as a progressive step in this area. Several of these re-configured IPS systems have been placed in service in Australia and overseas in the last three years, with the first of the new generation units constructed and commissioned by Como Engineers Pty. Ltd. at Mt. Fisher in the East Murchison of W.A. in September 1987. This plant was relocated to a new ore body at Darlot W.A. in February 1989. Use is made of a data base of raw plant performance figures from both Mr. Fisher and Darlot and its performance compared with other operating plants. Initial commissioning difficulties of the Mt. Fisher prototype and dis- cussed together with the modifications and operational procedures required to overcome these problems. Stripping times of less than 6 hours at 145 degrees have been achieved with barren carbon values less than l O ppm from loaded carbon values above 3000 ppm and with cell pass efficiencies reaching 90 per cent.

Jan 1, 1991

By P F. Knights, P Boniwell

This paper investigates the causes of low effective utilisation of the production drill fleet at the Telfer Underground Gold Mine, as measured by the percussion hours per shift. The first part of this paper focuses on a site time and motion study conducted to accurately identify shift time allocation and optimal drilling parameters (manual versus automatic, and suitable flushing mediums for varying ground conditions) as well as quantifying the business potential for automated or remotely operated production drilling. The second part of the paper focuses on the rate of successful hole completion for automated production drilling during shift changes. Two main areas of drill optimisation were identified. Firstly, a site-specific drilling procedure was established so as to ensure that all operators were drilling using optimal parameters. Total production metres per rig increased by 10.7 per cent as a result of the implementation of this standard. It was observed that a 25 per cent faster overall drill cycle was achieved using air mist flushing, and that manual drilling achieves a 19 per cent faster overall drilling cycle in comparison to automated drilling. Secondly, routine provision to the maintenance department of automation reliability reports that outlined the principal causes of unsuccessful hole completion led to an increase in production metres of a further 4.1 per cent, measured between January 2007 and August 2007. First hole automation reliability increased from 39 per cent to over 77 per cent over the same time period. Second hole automation completion was increased to 74 per cent, leading to a higher proportion of production achieved through automated technologies.

Jan 1, 2008

By M Sandy, A Vakili, J Albrecht

Although rock strength anisotropy is a well-known phenomenon in rock mechanics, its impact on geotechnical design is often ignored. No widely accepted guideline currently exists for its characterisation. Anisotropy can significantly control the failure mechanism and progression of damage into the rock mass, particularly in high-stress conditions. As such, it can play a key role in the stability of underground excavations and subsequent geotechnical design.This paper introduces the concept of anisotropy at both intact and rock mass scales. It then presents guidelines for measuring anisotropy and assigning rock mass strength properties. An improved unified constitutive model (IUCM), which can account for more complex failure mechanisms, is then briefly described. This IUCM is used to better understand the typical responses of anisotropic rocks to underground mining and to develop an improved damage classification scheme for these conditions.The application of conventional design methods in anisotropic conditions is shown to lead to significant errors. Two case histories are then presented, illustrating how the proposed methodology can improve the reliability and accuracy of the geotechnical analysis when compared with conventional design methods.CITATION:Vakili, A, Albrecht, J and Sandy, M, 2014. Rock strength anisotropy and its importance in underground geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 167–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

By Swain H. D, Kay R. L

Assessment of mineral reserves in any ore- body hinges on both mineralisation characteris- tics and the economics of extraction. The mineral reserves statement depends on interpre- tation of diamond drill information by geolo- gists, determination of the production plan and operating costs by mining and metallurgical engineers and prediction of future income by economists. The techniques used to generate the mineral reserves statement for Bougainville Copper Limited in 1969 are described and the accuracy of predictions discussed. Preliminary results from a geostatistical reassessment are comp- ared with the ore zone model, blast hole data and concentrator reconciled production results.

Jan 1, 1979

By Martin T

High methane content of the medium volatile metallurgical coal mined from the Coal Basin mines causes very difficult mining conditions. Rapid desorption into the mine ventilation system limits coal production, requires huge fresh air quantities and creates mine safety problems. In workings deeper than 2000 ft (600m) gassy coal and heavy cover create outbursting conditions. Cross-measure methane drainage has reduced ventilation requirements on advancing faces, but degasifica- tion of virgin coal is needed to improve mining Conditions.

Jan 1, 1982

By R Bourcier, T Rafferty

Following an underground coal mine explosion, it is important that ventilation is quickly restored to ventilate the mine and affect a mine rescue. To achieve this, surface ventilation fans must be suitably protected from explosion damage, but still able to be quickly restored.A review of all Australian coal mine regulations was carried out, revealing that Australia has no prescriptive regulations that specify the design of explosion relief panels and the protection of ventilation fans in the event of an underground explosion.To better define the level of protection required, this paper reviews and extracts details from relevant major international regulations and standards on the subject.A suitable design methodology for the protection of ventilation fans is presented that could be applied in Australia, using a combination of explosion relief panels, appropriate isolation of the fan, and ventilation shaft/mine design.CITATION:Rafferty, T and Bourcier, R, 2013. The protection of surface ventilation fan installations from underground explosions, in Proceedings The Australian Mine Ventilation Conference , pp 169-173 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Burgess JM

Research on gas distribution in the iron- making blast furnace has been conducted in three separate areas. Firstly, experimental work has been conducted to determine the important parameters which dictate the pressure losses in homogeneous and heterogen- eous packed beds. Secondly, a theoretical analysis of gas flow through the furnace softening-melting zone has been undertaken to determine the effect of the shape of the zone on the distribution of gas flow towards the furnace walls. Thirdly, a theoretical programme has been undertaken to develop methods for the prediction of furnace soften- ing-melting zone shape from furnace tempera- ture and gas composition measurements.

Jan 1, 1980

By Lin Bin, Qain Minggao, Qu Qundi, Yao Zhichang

This paper describes the application of a 89C52 chip microcomputer in hydraulic pressure information monitoring system of powered supports in a coal face, and the details of circuit and software of a monitoring system substation. Each substati

Jan 1, 1998

By Reichman J. P

Extensive use is made of a small scale computer (IBM 1130), in the calculations of ore reserves for Western Mining Corporation's nickel mine at Kambalda, W.A. All surface drilling data such as assays, density and location information, are stored on disk files at the Company's Technical Computing Centre at Perth, W.A. The computer is used to search through the data, select significant ore intersections, calculate the area of influence of each intersection and perform the necessary calculations to arrive at an estimate of the ore reserve. Comparing the computer-assisted ore reserve calculation with an entirely manual operation, it is estimated that a saving of 40 percent in time is achieved together with

Jan 1, 1973

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By J A. de la Torre, I R. Cerna, G K. Karadjian

The La Colorada underground mine in Zacatecas, Mexico is a mechanised cut-and-fill silver mine with a capacity of 1250 t/d. The project focused on training the mine’s experienced operators for a fleet of underground trucks, through the use of a training simulator. The project was run by the simulator vendor, in collaboration with the mine’s maintenance, safety and production management.A training program was created targeting maintenance reduction, productivity improvement and increased utilisation and availability. Operators were first acclimatised to the simulated environment, had their current performance baselined, then received targeted coaching, with the process repeated to reinforce learnings. Concurrently, production, maintenance, and safety data was being measured in the real world to measure skills transfer. Due to limited telemetry available from the equipment, many of the data points for the project were sourced from maintenance logs, and accounting data.Equipment failure data measured from unscheduled maintenance records showed an overall 6.5 per cent decrease in unscheduled maintenance following the implementation of the training program. This rate of reduction correlated with the significant decrease in equipment abuse behaviours measured within the simulator during this period. Additionally, overall maintenance activities showed a significant decrease, confirming that reductions in unscheduled maintenance were not achieved through increases in scheduled maintenance. The reduction in equipment damage also increased availability and utilisation of the truck fleet. This highlights that the maintenance improvements not only reduced maintenance costs, but made the fleet available for more production. Moreover, the variability of the operator performance was decreased by 86 per cent, and the difference between their best operator and the worst is less than the baseline; this showed a gap where machine abuse, productivity and cost are impacted directly.This project illustrated that even small-scale mining operations with an experienced operator workforce can achieve positive return on investment (ROI) from simulation-based training. It also highlights that in the absence of equipment telemetry, alternative data sources such as accounting data and maintenance logs can be used to quantify ROI from training.CITATION:Karadjian, G K, de la Torre, J A and Cerna, I R, 2017. Innovations in underground hard rock operator efficiency – through simulation-based training technologies and processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 53–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By S Oliver, D Willingham

"Although a resource model is central to the mineral resource value estimation process (Glacken and Snowden, 2001), creating it is a labour intensive task and in the end it is a limited representation of the actual orebody. Creating this resource model is a labour intensive task that requires inputs from geology, mining, metallurgical and commercial disciplines. It requires thousands of samples from hundreds of drill holes to be verified, grouped in geological domain, interpolated and then valued. Even after all this effort, a model is only an estimation; therefore further significant effort has gone into quantifying uncertainty in the model and subsequently risk around any value estimates derived from the model. Further risks to model quality are introduced through poorly conditioned data or incorrect assumptions.This paper proposes the application of machine learning to automate the resource model development. Machine learning is applied to the traditionally manual tasks of geological formation, domain identification and validation of the block model mineralogy. Through automation the resource estimation process can be accelerated, allowing more drill holes or a larger resource body to be processed in a given time frame, or allowing the process to be more agile to changes in input data and assumptions. A case study based on drill hole data from a Western Australian iron ore deposit (Government of Western Australia, Department of Mines and Petroleum, 2015) is used to demonstrate the application of machine learning in this process.CITATION:Oliver, S and Willingham, D, 2016. Maximise Orebody Value through the Automation of Resource Model Development Using Machine Learning, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Merwin RA

The recent development of rare earth permanent magnets has revolutionised the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focusing on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

This report on the 5th International Conference on Underground Space and Earth Sheltered Structures, which was held at the University of Technology, Delft, the Netherlands, on 2 to 5 August 1992, was submitted to the members of the Australian Underground Construction and Tunnelling Association. The report describes the conference themes and outcomes and puts forward some observations about a growing world-wide interest in the promotion of appropriate uses of underground space. The report recommends the creation of an Australian centre for research to bring together a wide range of professional disciplines and to focus attention on the potential benefits of using underground space.

Jan 1, 1993

By N Anderson

With traditional grade control processes, geological models are created by geologists at the completion of the data collection stage and wireframe construction is closed off at a set date to allow for time to complete the estimation process. Any issues identified at earlier stages or the addition of new data requires the estimation process to be started again. Alternative interpretations are explored only if time allows and often in a limited fashion. An alternative workflow has been developed at the Waihi Underground Gold Mine utilising Leapfrog Edge and Seequent Central. Geological and grade control models are created, dynamically linked, and saved as separate branches. A project geologist is able to work on the grade control model and a mine geologist on the geological model simultaneously. This allows for a non-linear modelling workflow with continual review and feedback. The introduction of new data can occur right up to the model due date, with data collection, validation, alternate interpretation, and review happening incrementally. Models are categorised and stored in Seequent Central according to project status. An approved version of the geological model and grade control estimate are uploaded at the time of release and transparently capture all data used at a point in time, as well as the review process. Dynamically updating models for grade control has reduced turnaround time while increasing accuracy and quality. Estimates of individual domains are vastly improved from being able to rapidly evaluate the effects of model parameter changes in real time and 3D. Development and stope design directly benefit from these streamlined processes, with higher quality, timely production occurring as a result.

Mar 22, 2022

By Q Fan

The steelmaking desulfurisation plays an important role in coal-based steelmaking route of blast furnace and BOF converter within the flow sheet of BF-deS-BOF. With the advent of H2-based ironmaking and steelmaking process, the transition flow sheet of DRI-Smelter-BOF has been assessed and developed by the steelmaking industry. What is the role of deS in H2-based route of DRI-smelter-BOF? This paper will present the influence of sulfur-containing iron ore on steelmaking desulfurisation and the leading role of EAF-smelter played in H2-based steelmaking route. The sulfur contents of iron ore vary considerably around the world and lower-grade iron ores with high sulfur are likely to be used for H2-based route, a considerable amount of sulfur that comes from DRI will report to the melt of EAF-smelter and the operating conditions of EAF-smelter also impact the sulfur content of the hot melt for steelmaking deS. The EAF-smelter of H2-based route is the focus of the steelmaking industry at moment, unfortunately, an industrial-scale EAF-smelter has been the missing link of the flow sheet of DRI-Smelter-deS-BOF, despite similar EAF-smelters being used for various applications of Fe-Ti and Fe-Ni processes. The latest progress is that several pilot-scale and industrial-scale EAF-smelters with reducing capability are planned for construction within next several years and low-grade Australia iron ores are certainly to be employed as basic feedstocks for H2-based route of DRI-Smelter-deS-BOF.

Sep 18, 2023

By H Kurth

Oyu Tolgoi copper and gold mine in the southern Mongolia holds mineral resources that make it one of the largest known copper and gold deposits in the world. The project is operating an open pit mine on the near surface of Southern Oyu deposit and developing underground block-caving mine at the Hugo Dummet North where 80 per cent of total resources exists. Oyu Tolgoi (OT) commenced open pit mining in 2011 and implemented an industry standard blasthole sampling, and ordinary kriging grade control estimation with block-out process. Since 2017, grade control improvement projects have successfully completed that have led to the implementation of current, improved grade control system. Geological model is updated by blasthole logging on Leapfrog® and used for daily grade estimations. GC estimation is proceeded solely on Vulcan® by running Lava script and integrating with a relational database. Combination of block-out procedure produces GC model which is updated in Vulcan® and as well as in the database simultaneously. Switching to the integrated database eliminated many manual processes such as importing and exporting data and enabled access to the database anytime, anywhere and from any device. Thereby, these improvements allowed to increase an efficiency, create a comprehensive reconciliation system and reduce operational risks. We are looking forward to expanding applications of integrated grade control data stored in the database. This paper outlines how the grade control system was developed at OT’s open pit mine, and how it is integrated into the short range mine planning, mine reconciliation workflow and ultimately enabled development of various automated reporting systems.

Mar 22, 2022

By E Jak, J Chen, B Hogg, S Nikolic, S Nicol

The quantity of post-consumer ‘waste’ materials generated each year is rapidly increasing. These materials can contain significant quantities of critical metals and present an environmental challenge if landfilled. The ISACYCLE™ technology is a proven solution for the processing of these materials. In the ISACYCLE™ furnace, the post-consumer materials are processed to recover energy along with any contained critical metals, in the form of a base metal alloy or matte. In addition, a clean aggregate (slag) is generated, which has the potential to be used for a range of applications in the construction industry. This slag is commonly based on a fayalite slag but is modified to manage the complex feed. This paper will review the fayalite slag system and the theoretical modifications required for treating urban wastes. Slags from an ISACYCLE™ furnace processing urban wastes have been sampled and characterised. The chemistry of these samples will be reviewed and compared to the expected theoretical modifications required.

Jun 19, 2024