Search Documents

By S Lockie, G Ivanova, J Rolfe

One of the consequences of mining expansion in the Bowen Basin region of Central Queensland in Australia has been a substantial increase in demand for housing, with subsequent impacts on housing and rental markets. Those pressures are reduced to some extent by a proportion of the workforce choosing to live in other centres and commuting to workplace for block periods. The main factors influencing location choice are: housing availability and affordability, basic urban services and lifestyle of the town and the town physical attractiveness such as coastal town. Low costs housing provided by the mining company acts as an attracting factor for some miners to live in the mining town. Recommendations for three short-term and two long-term strategic policy guidelines to address housing situation and location issues are provided.

Jan 1, 2009

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By T Y. Dube

In this paper current net present value (NPV) based mine valuation techniques that take into account market and private risk are discussed and analysed. Potential pitfalls that arise from the application of a portfolio, market or commodity based risk metric to a mining project are identified. An alternative non-simulative framework for quantifying and factoring market and private risk in NPV calculations is proposed and then applied to a hypothetical case study in an attempt to overcome identified pitfalls. Mathematical proof that a static discounted cash flow (DCF) calculation can underestimate or overestimate mine NPV is presented, the conditions for each are outlined and the degree of underestimation defined.CITATION:Dube, T Y, 2012. How the use of market-based risk metrics can undervalue good mining projects and overvalue poor ones, in Proceedings Project Evaluation 2012 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By Y Wang

Inadequate goaf gas control may lead to gas exceedances in the ventilation return air, which will trip power in longwalls and cause production stoppage. To effectively control gas emissions, Australian mines heavily rely on drilling vertical goaf holes to capture coalmine methane before it migrates to mine openings. The wide application of goaf gas drainage may change the goaf pressure distribution, lead to more ventilation air leakage, and consequently increase gas explosion and spontaneous combustion risks. This paper focuses on analysing goaf gas drainage production data from a case study longwall mine in Australia. The correlation between suction pressure, total flow rate, gas flow rate and air leakage rate were analysed in detail as the face-to-hole distance changes. Suction pressure is found to be positively correlated with total flow rate, and their correlation also varies at different goaf locations due to various goaf compaction and flow resistance. This paper also proposed a theoretical method to calculate the goaf resistance of ventilation air leakage pathways. Based on several basic assumptions and different goaf drainage scenarios, the leakage airflow pathway resistance in the goaf at different face-to-hole distances can be calculated. The model results suggested that the resistance of air leakage pathways from the working face to individual goaf holes increased with the face-to-hole distance. The resistance results can also be used to calculate the corresponding permeability at the same position, which can be used as input data for CFD or Ventsim models.

Oct 12, 2022

By D Brereton, C J. Moran

Intensive resource extraction, in the form of multiple mining operations, presents significant assessment and management challenges for resource developers, governments, community and the environment. Cumulative impacts, ie the successive, incremental and combined impacts (both positive and negative) of an activity on society, the economy and the environment, can place significant pressure on social, economic and environmental capital and render conventional mine-by-mine approaches to management ineffective. Cumulative impacts can be what are most important to environments, communities and economies surrounded by multiple mining operations because cumulative impacts are what they experience. There is much to gain from increased consideration of cumulative impacts. Unmitigated impacts have the potential to delay or even prevent expansion of mining in existing and prospective areas. On the other hand proactive management of cumulative impacts can benefit regional environments and communities and contribute to the industryÆs social license to operate. Resources are often not the limiting factor to better cumulative impact management. More effective coordination of existing resources may go a long way toward mitigation and enhancement, and better planning and assessment may help avoid impacts and exploit opportunities for efficiency gains through reduced duplication. In this paper we draw from working examples to present five practical assessment and management strategies applicable to resource companies to enhance positive, and avoid and mitigate negative, cumulative impacts. The strategies are presented based on their capacity for achieving outcomes, ease of implementation and cost effectiveness and are drawn from a multi-year study on the assessment and management of cumulative impacts in the Hunter Valley, New South Wales and a follow-up study to improve cumulative impact assessment and management practice in the Australian coal mining industry, both reported elsewhere.  

Jan 1, 2009

By S Sullivan

A recent review of resource reports lodged to statutory bodies found geological models with oversmoothed or unrealistic lithological boundaries, many of which do not represent geological appearance in the field, pit or underground drive. The underlying data is often too complex or messy to be incorporated into the resource model and is thus a simplification of reality, to the detriment of the mining operation and its shareholders. Volumes can be over- or underestimated and subsequent grade predictions can be misplaced, combining to cause over- or understatement in resource reporting to stakeholders and statutory authorities. Domain models can be improved with new modelling techniques such as machine learning. However, with poor data or improper use of machine learning techniques, the conclusions can be just as misleading as with current techniques. Machine learning rarely offers a single ‘right’ outcome, rather a range of possible outcomes from the data provided. But importantly it can take advantage of the full richness of data for more informed models. Machine learning also provides confidence in its predictions so that uncertainty in the resultant models can be quantified and passed through for risk assessment during mine planning and operation. This paper will discuss the factors accentuating complexity in deposit modelling: data diversity, structural controls, chemistry, data volumes, process workflows and external non-geological constraints. A case study illustrates the risk of reducing or ignoring complexity, which can result in an overly simplified geological model.

Mar 22, 2022

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

By S Ellis

In January 2008 Chirano Gold Mines Limited committed to expansion of the Chirano Gold Project from its existing design capacity of 2 Mtpa ROM ore to a new design value of 3.5 Mtpa. In addition to increased throughput, the design had to contend with increasing ore hardness and competency, while at the same time make cost effective use of existing equipment with minimum disruption to existing production. The solution adopted involved some novel approaches including tertiary crushing and operation of the SABC circuit in overflow ball mill mode and parallel elution with a common acid wash column. This paper describes the approach taken to the design of these elements to achieve a cost effective and safe capacity expansion.

Aug 8, 2011

By A Fern, A Hawkes, o

This presentation will cover: the importance of high-quality safety leadership; insights from a Safety Climate Survey that includes responses from 7903 employees working at 19 Australian mining organisations; the results of a critical control verification (CCV) coaching intervention; and recommendations for improving safety leadership in high-risk work settings. Safety climate is a representation of the deeper culture that exists in an organisation. Safety climate is predictive of behaviour, performance and reporting in organisations. Leaders play an important role in the establishment and maintenance of culture. Perceptions of safety climate were collected from 19 Australian mines (n = 7903 employees). These results indicate that the Australian mining sector is doing well in team support for safety and supervisor safety commitment. There were negative perceptions of willingness to report errors, employee involvement in safety initiatives, psychological safety and emergency readiness. Perceptions of safety leadership were in the fair range, with recognising behaviours perceived lowest, falling in the poor range. The underreporting rate was at 25 per cent indicating that 1 in 4 incidents are not being reported. Analyses exploring climate, leadership, safety behaviour and well-being will also be discussed. The integrity and success of critical risk management systems is often determined by the quality of safety leadership. Leaders need a mix of technical safety knowledge and interpersonal skills to be able to support the workforce to build critical control knowledge that invites open and collaborative discussions to find new or improved solutions. Forty leaders at a major mining operation completed training and 5-weeks of coaching focused on developing critical control verification competencies. The follow-up evaluation demonstrated significant improvements in relationship building, observation of controls and overall capability. Overall, insights from multi-organisation climate data and a prepost coaching intervention will be discussed and recommendations and practical guidance for leaders will be provided.

Apr 16, 2024

By Belton G. R

The kinetics of the interfacial reaction of H2O on liquid silica-saturated iron silicates has been studied by means of measurement of the HDO-H2 isotope exchange reaction. The apparent first order rate constant, ka, was found to be inversely proportional to the H20/H2 ratio, consistent with two electron (melt to adsorbed/dissociating molecule) transfer mechanism and can be given by the expression In ka = -1.97 x 104/T + 1.57 - ln(pH2O/pH2), where the units for ka are mol cm -2 s-1 atm 1. The results of the current study are shown to be consistent with the indirect measurements of earlier work.

Jan 1, 1987

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Kurita K, Tanaka T

In order to clarify the gas flow and motion of coke and reaction in the raceway, the mathematical raceway model was developed. This model consists of the equations of momentum and continuity of gas and coke. The simulated results were compared with the results of the cold and hot experimental model. The relationship between the blast volume and the raceway size, the pressure distribution and the velocity distribution of coke are in good agreement with the experimental results. Moreover the equations of reaction and heat conservation were simultaneously calculated with the dynamic equations. Distributions of gas composi- itions and temperature were simulated and found to be in good agreement with the distributions of gas compositions of CO, CO2 on the tuyere level measur- ed in the hot experimental model.

Jan 1, 1981

By J M. Wallis

Heavy mineral sand exploration drilling prior to the 1970s generally utilised open hole auger and air-blast type drilling. However, mining reconciliations were poor and limitations on accuracy and precision of drilling results were severe.Working with the exploration companies, Wallis Drilling principals designed various systems, including what was termed the ‘Eneabba System’ and then the ‘Capel Twin-Tube System’. Eventually the company with its improvements developed and patented the Aircore Drilling System.Aircore drilling has subsequently become recognised as an excellent drilling system for exploration and mine-sample drilling that gives good precision and accuracy in sampling both above and below water. Its use has also been extended to many other commodities and is used in a number of overseas countries.This paper documents anecdotally the development of the system, identifying problems encountered during the times it was evolving and of the means to overcome the problems as being the documentation of the story by the inventors and developers in Wallis Drilling Company. Aircore drilling system is a Western Australian technological development owing its existence to the designing and incorporation of a number of discrete improvements along the way and recognises the tenacity and inventiveness of all who contributed to the system, in both Wallis and also in a number of companies that gave the impetus to succeed.

Oct 5, 2011