Search Documents

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

Qualitative measurement of respirable dust in metal mines is limited and an example of this is demonstrated at Northparkes Mine, where operational experience was sought for measuring dust standards and identifying exposure limits. However, relying on operational experience has limited value due to variation in observations from person to person and is based on visible dust (which is larger in size than respirable dust). However, with sophisticated dust measuring equipment, like the real-time aerosol monitor, dust concentrations can be accurately measured and recorded concisely. Research conducted as part of a collaborative agreement on behalf of Northparkes to launch an occupational dust monitoring program was implemented on the mine site. To form the basis of this research, it was hypothesised that no proper dust measuring testing at the mine site had been adequately identified. In addition, existing occupational hygiene monitoring programs did not adequately quantify employee exposures to these hazards. This project will outline the results of an occupational dust monitoring program, hence greatly improving the capacity to quantify the health risks posed to employees.

Jan 1, 2008

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By Kyle J. H, Misra V. N

The recovery of copper from a flotation concentrate using ferric chloride leaching has been investigated. The concentrate from the Horseshoe Lights Mine near Meekatharra, Western Australia, contained mainly digenite, pyrite and talc minerals. Over 95 per cent of the copper was dissolved in an acidified ferric chloride solution in one hour at 70¦C and ambient pressure. The pyrite and gangue minerals did not react. The leaching process was found to consist of four separate reactions and the shrinking core model was used to describe the process. The effects of particle size, temperature, concentration of FeCls, stirring speed and leaching time on metal dissolution were investigated. The apparent activation energies in the second, third and fourth reactions of leaching of copper concentrate were 28.8, 11.9 and 53.9 kJ/mol, respectively. The optimum conditions for the leaching of copper from the concentrate, within the range of conditions studied were: particle size 63 per cent minus 38 ¦m, a ferric chloride concentration of 1.48 M, a temperature of 70¦C, and a stirring speed of 800 rpm.

Jan 1, 1991

By Higuchi K, Sekimoto Y

In this report,the results of the large diameter drilling tests in coal seams assisted with water jet are described. The stress relief in coal seams by this new method is as effective as by the conventional method and the penetration speed by this method is 1.5 times as fast as by the other method. 1 Introduction The average mining depth of Japanese coal mines has already attained about 700m from the surface. Almost all coal mines are suffered from occurrence of coal and gas outbursts. To prevent outbursts, some countermeasures are taken generally. In particular, large diameter stress relief borings have been carried out quite often at Akabira coal mine located in the northern part of the Ishikari coal field in Hokkaido,JAPAN. These borings have had successful results but the drilling work of such large diameter

Jan 1, 1987

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By K Sommerville

BHP Billiton’s Area C iron ore operation has been in production since 2003. During 2010, below water table mining in the Marra Mamba formation commenced and dewatered ore has been successfully processed through the plant.The ability to mine below water table material increases reserves. Pits can be dewatered using a combination of ex-pit and in-pit bores. Critically it is important to allow suffi cient lead time to dewater. For Area C, in-pit bores yield the most water which presents challenges in every day operations when mining around bores. Operationally there are steep learning curves in obtaining equipment, training personnel and setting up infrastructure. Core risks include lifting, refuelling and maintaining gensets. The pipework, extraction and re-establishment work can be very manual.The challenges include blasting, mining, stockpiling, processing, water balance and disposal. Maximising up time on bores whilst minimising impacts to blast practices have evolved. Blast practices now align bores to the edge of patterns. Protecting bores have evolved from stemming bores with rock and re-drilling to using gas bags which require no drills. Based on moisture and material properties, mining of dewatered material can be categorised into three groups:1. normal,2. sheeting, and3. sheeting and top loading.Ore can go straight to the plant ore to drying pads where it takes between one and three months to drain.Stock management of these piles is important to ensure efficiency of the plant. Rules have been established for blending wet material to maintain feed capacity and some modifications to plants have been made. Dewatering of pits poses a challenge for water use. Initially turkey’s nests were established to capture water and use for dust suppression. As water abstraction has increased methods of management include using exhausted pits for storage and evaporators. Managed Aquifer recharge and use in potable water are being considered. An over arching coordination of the capacity and use are required.Important elements in dewatering include:• capacity models,• capital,• long to short planning,• day to day coordination, and • water level monitoring and balances. Success in dewatering requires a cross function team working towards a common goal. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

The mmmg operations carried out by North Broken Hill Limited, necessitate the use of four shafts for the haulage of ore, men, and supplies. These are:-1. Blackwood's Shaft.-British Section, which has 100 feet intervals between levels to the bottom 800 feet level plat;2. Thompson's Shaft.-British Section, which has 100 feet intervals between levels to the bottom 1400 feet level plat;3. No. 1 Shaft.-With intervals between levels:(a) 100 feet to the 800 feet level,(b) 150 feet from 800 feet level to the 1700 feet level;4. No. {2 Shaft.-2770 feet from collar to bottom plat, with intervals between levels: (a) 100 feet to 800 feet level, (b) 150 feet from 800 feet level to the 2600 feet level. (c) 170 feet from 2600 feet level to the 2770 feet level.All shafts have two cage compartments, and the No. 2 Shaft a skip installation in addition.For the control of hoisting operations an electric signalling system is installed on each shaft, and is supplemented by a counterbalanced rope pull ("Knocker line") operating a surface gong. The latter system is shown diagrammatically in Fig. 1.Two sets of electrical equipment are used per shaft. The first, shown in Fig. 2, is that operated by the braceman or...

Jan 1, 1940

By A Kuras

Segmental tunnel linings are becoming more common in Australia. One current project employing a segmental lining is the City West Cable Tunnel (CWCT) in Sydney. The project has been commissioned by Energy Australia and is currently being constructed by Thiess Pty Ltd. The project includes 1.6 km of tunnel boring machine (TBM) driven, segmentally lined tunnel. The majority of the CWCT will be excavated through Hawkesbury Sandstone. The tunnel is required to carry a 132 kV electrical circuit under SydneyÆs central business district (CBD), between Haymarket and Energy AustraliaÆs City North Substation on Sussex Street. The segmental lining has been designed as a 3.2 m internal diameter, 200 mm thick universal ring with six trapezoidal segments. The design and detailing of this segmental lining presents some noteworthy challenges, including exposure to saline groundwater, and the exclusive use of steel fibres for flexural and tensile concrete reinforcement. This paper describes some of the key elements of the segmental lining design. These include:the case for choosing segmental linings over other forms of tunnel construction;the major design checks required of a segmental lining including ground loading, hydrostatic loading, joint bearing, joint rotation, ram loading and the early strength lifting case;the benefits of using steel fibres over conventional steel reinforcement;the design approach used for steel fibre reinforced concrete;the application of 3D computer modelling in the design;the provision for components including connector dowels and gaskets;the design for passive fire resistance; andthe design for durability of steel fibre reinforced concrete in a saline environment. Segmental lining design requires the application of specialist design approaches. Input is required by the construction team, as the methods of demoulding, handling, transportation and installation impact on the lining design. As the segmental lining is functioning as immediate ground support and also a permanent lining, high standards of manufacture and construction quality control are required to ensure that the 100-year design life is met. The requirement for a watertight tunnel means that detailing and installation of the EPDM gaskets is of importance.

Jan 1, 2008

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Ryan CG, Both RA, Mernagh TP, Large RR, Hunns SR, Gemmell JB

The Hellyer and Mt. Chalmers deposits are mound-style volcanic-hosted massive sulphide (VHMS) deposits in Australia. Textural, petrographic and microthermometric investigations of fluid inclusions in the Hellyer stringer system indicate that Type I, primary, liquid-vapour inclusions are 10-15 pm in size, and yield homogenisation temperatures of 170-220¦C in early 2A veins, 165-322¦C in main-stage 2B veins and 190-256¦C in late-stage 2C veins. These data suggest a waxing and waning thermal history. However, the average salinity remained between 8-11 NaCl equiv. wt % in all Stage 2 veins. At Mt. Chalmers, Type I inclusions up to 20 ¦m are found in quartz from the mineralised zone, and these inclusions yielded homogenisation temperatures of 160-268¦C and salinities of 5-8 NaCl equiv. wt %. Laser Raman spectroscopic (LRS) analysis indicates the presence of CO2 (

Jan 1, 1995

By M Skead, H Michael, R Chase, A Davidson

Ashanti Goldfields CompanyÆs (AshantiÆs) most recent development is the Geita Project in the Lake Victoria Goldfield of NW Tanzania. It comprises six distinct gold deposits within two mineralised trends: Nyankanga, Lone Cone, Geita Hill (Geita trend) and Matandani, Kukuluma and Area 3 West (Kukuluma trend). Between 1936 and 1966, the Geita area produced an estimated 5.5 M tonnes of ore from five underground deposits at an average recovered grade of 5.3 g/t. The discovery of Nyankanga was made by Ashanti in 1996 from RAB drilling of a +100 ppb Au anomaly in laterite soil above ferricrete cover. The Kukuluma trend was discovered by SAMAX Resources (taken over by Ashanti in 1998) between 1996 and 1997 from RC drilling of a +80 ppb Au laterite soil anomaly. Oxide facies banded iron formation (BIF) of the Upper Nyanzian System forms prominent topographic ridges and is the dominant host lithology for gold mineralisation. The ridges are flanked by felsic tuff units which lie stratigraphically above. Syn-genetic lamprophyre (vogesite) and post-genetic felsic dykes are also seen in the Geita trend. At Nyankanga a granodiorite-diorite suite has intruded as dykes and sills into BIF from a plug centred on a WNW fault and has produced wallrock alteration assemblages similar to those seen in Cu-porphyry systems (potassic, propylitic, etc) as well as sulphide and gold deposition. However, the main ore-grade mineralisation (as in the rest of the Geita trend) is controlled by low-to-medium angle structures dipping north-west and north with numerous splays in the hanging wall. High-grade shoots at Nyankanga plunge to the west and to the north-west, being lithologically and fault-controlled respectively. At Geita Hill the higher grade shoots are controlled by fold noses in BIF dipping to the north. Free gold occurs within fractures of sulphides. The deposits of Kukuluma and Matandani occur on an ancient (possibly Cretaceous) erosional plateau and are related to two WNW to NW trending shear zones, discordant to the local strike of the BIF sequence. Complete oxidation occurs up to 120 m depth and there is a strong supergene component to the gold distribution. Primary gold mineralisation is divisible into two distinct assemblages: arsenopyriteûpyrrhotiteûmagnetiteûchlorite associated with brecciated cherts and pyrite associated with shaley banded ironstones. Area 3W is most likely the fault-displaced extension of the same mineralised trend and comprises thin, intermittent zones of high-grade gold mineralisation occurring adjacent to a ridge in banded cherts and minor BIF. Current resources (measured, indicated and inferred) for the project are estimated at 89.24 Mt at an average grade of 4.17 g/t (11.97 Moz of contained gold) at a 1.0 g/t cut-off grade. Of this 9.83 Moz is within the Geita trend and 2.14 Moz is within the Kukuluma trend. A resource of 2.74 Moz is from an inferred resource at depth at Nyankanga where the viability of an underground operation is being studied. Proven and probable reserves are 49.77 Mt @ 3.46 g/t (5.54 Moz) based on a $325/oz gold price providing a mine life of ten years at an average production rate of 500 000 oz per year. Reserve estimation was carried out using mineable polygons to select resource blocks based on a series of mining and costs parameters. In addition key cost parameters were tested to provide sensitivities for pit optimisations and pathfinders for negotiations with suppliers and contractors. Construction began in March 1999 and first gold is expected to be poured in the second-quarter 2000.

Jan 1, 2000

The first grant of land rights in Australia was pursuant to the Aboriginal Land Rights (Northern Territory) Act 1976. That Act has been at the core of the dispute between land rights and miners' rights. The mining industry believes that the Act, in giving a right of veto to Aborigines with respect to exploration and mining on Aboriginal land, has been responsible for a stagnation in exploration amd mining activity in the Northern Territory. In February 1985 the Commonwealth Government released for public comment its preferred model for national land rights legislation. The model has been opposed by the mining industry because it believes, first, that land rights is a matter which should be left to the States and, secondly, that the detailed mechanisms contained in the model constrain the industry in the manner of the Northern Territory legislation. Aboriginal leaders have opposed the model because it does not, in their view, measure up to undertakings given by the Commonwealth Government and, in addition, it provides for amendments to the Northern Territory legislation which are likely to result in the loss of the Aboriginal veto right. Are land rights and miner's rights compatible? The answer is yes provided all parties, including Governments, are prepared to talk and compromise and Governments recognise that the grant of land rights and any control by the Aboriginal people of exploration and mining on their land is not a substitute for raising the living standards of Aborigines as a significant group of disadvantaged Australians.

Jan 1, 1986

Kalgoorlie Consolidated Gold Mines Pty Ltd is currently developing the 'Super Pit' gold mine in the mining area known as the Golden Mile adjacent to the city of KalgoorlieBoulder, Western Australia. The presence of numerous abandoned mine workings and complex structural geology has required considerable geotechnical input into the determination of the optimum pit slope geometries for both interim and ultimate pit slopes. Slope design is based on detailed site investigation and stability analysis which is balanced with historical operational experience. This paper discusses the process of determining the optimum pit slope angles for each of the stages of the west wall of the 'Super Pit'. The risks associated with slope instability are discussed for each stage.

Jan 1, 1994

The Loy Yang Overburden System initially consists of a 60 000 tonne/day Bucket Wheel Excavator (BWE) (No. 14), a 2 m wide Conveyor System and a Travelling Stacker (No. TS4). The paper discusses details of the plant and the influence the soft clay overburden has on the design of the plant, to handle the dif- ficult Latrobe Valley overburden.

Jan 1, 1982

By B Morey, J Gordon, P Mackenzie

Mount Tom Price Mine is peerless amongst Rio Tinto iron ore resources around the world. It has provided Hamersley Iron with premium quality, high lump yield haematite ore over the last four decades. The Brockman type bedded ore, containing bands of haematite and shale of varying thicknesses has been traditionally bulk mined to either high-grade or low-grade based on alumina cut-off grades. As open pit mining has progressed deeper into the orebody approaching the keels of the megastructure, increased structural complexity, chemical and physical variations in the ore, unfavourable ore presentation and reduced blending options have become an issue for grade control and may have serious impacts on product stockpiles. The grade blocks and boundaries must be accurately defined according to geological contacts and where identified, selective mining may be applied. Therefore in-pit geological mapping is the definite and ultimate guide to achieve target grades and grade predictions. Under this scenario, it is absolutely vital that the mine geology team ensures this geological knowledge is passed onto the related departments including mining crews as well as to the short- and long-term planners.

Jan 1, 2002

By B Zhou

Geophysical borehole logging, which measures various in situ petrophysical parameters, can be used not only for qualitative interpretation such as strata correlation, but also for geotechnical assessment through quantitative data analysis. It can play an important role for safe and productive mining operations. Here we provide various applications of geophysical logs such as the estimation of the strength of intact rock or unconfined (or uniaxial) compressive strength (UCS), automated lithological/geotechnical interpretation, geophysical strata rating and orebody delineation and grade estimation. These derived parameters could provide input to control of geological and geotechnical models. This could assist site geologists and planning and production geotechnical engineers to predict and manage mining conditions on an ongoing basis. Both conventional logs such as density, natural gamma and sonic, and less common logging data such as full waveform sonic and televiewer data are examined for different applications. Although the examples used here are mainly for coal mining applications, but they can be equally applied to hard rock metalliferous mining such as iron ore mining.

Nov 8, 2021

By Bronson B

The geotechnical and environmental aspects of heap leaching are very closely tied during design, operations and closure. Potential environmental impacts from heap leaching are mostly due to land disturbance and water quality issues, including both groundwater and surface water. Water quality issues are mostly related to containment design, which is primarily a function of proper sizing of the facilities and site specific liner design. Geotechnical analyses is the dominant discipline in providing cost efficient, operationally effective and environmentally sound heap leach facility designs. Much has been published on geotechnical aspects of heap leach design, for example Van Zyl, Hutchison and Kiel (1988) and Van Zyl (1987). This paper will emphasize a few specific aspects related to the geotechnical and environmental consideration for heap leach projects. These aspects are: ò site investigation; ò containment design; ò slope stability; ò heap flow dynamics; and ò closure design. Design of a heap leach project must consider not only the operating life but also closure and post-closure considerations. As a matter of standard practice, designing for closure is an extremely important concept. Not only is it important for environmental aspects, but experience also shows that projects designed for closure will be overall more economical for the total life cycle of the project. Closure considerations are also important during project feasibility evaluations to ensure that total life cycle costs are evaluated.

Jan 1, 1994

The geotechnical and environmental aspects of heap leaching are very closely tied during design, operations and closure. Potential environmental impacts from heap leaching are mostly due to land disturbance and water quality issues, including both groundwater and surface water. Water quality issues are mostly related to containment design, which is primarily a function of proper sizing of the facilities and site specific liner design. Geotechnical analyses is the dominant discipline in providing cost efficient, operationally effective and environmentally sound heap leach facility designs. Much has been published on geotechnical aspects of heap leach design, for example Van Zyl, Hutchison and Kiel (1988) and Van Zyl (1987). This paper will emphasize a few specific aspects related to the geotechnical and environmental consideration for heap leach projects. These aspects are: ò site investigation; ò containment design; ò slope stability; ò heap flow dynamics; and ò closure design. Design of a heap leach project must consider not only the operating life but also closure and post-closure considerations. As a matter of standard practice, designing for closure is an extremely important concept. Not only is it important for environmental aspects, but experience also shows that projects designed for closure will be overall more economical for the total life cycle of the project. Closure considerations are also important during project feasibility evaluations to ensure that total life cycle costs are evaluated.

Jan 1, 1994