Search Documents

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

Thiess Dampier Mitsui's Moura-Mine is located in the south-eastern corner of Queensland's Bowen Basin, some 180 kms west of Gladstone. Current requirements of the open cut operation are to drill and blast 25 million cubic metres of overburden per year, consuming some 12,000 tonnes of explosive in order to meet the requirements of the mine's four operating draglines and one overburden shovel. By early 1985 it had become obvious that the existing drill and blast equipment and technology could not cope with the long-term needs of the open cut mining operation. Three 61R drills were in need of rebuilding or replacement. Bulk ANFO trucks working two shifts per day were unable to match the requirements of the four draglines dne to long travel distances, slow discharge rates and their inability to load water-resistant products into the increasing number of wet holes. This paper outlines the significant steps taken to introduce new equipment and technology and the resulting improvements in the mine's productivity and economics.

Jan 1, 1986

By H Mischo, G Barakos, J Gutzmer

The continuously growing demand for rare earth elements (REEs), in combination with the crisis of 2009 and the price spike of 2011, has initiated a treasure hunt for rare earth deposits all over the world in recent years. Since then, commodity prices have declined and are now quite stable, yet the world is still dependent on China’s dominance of the market and its export policies. Exploration is unremitting and numerous resources of potential interest have already been revealed in many countries; however, proceeding to mining operations is not that simple, especially when it comes to the exploitation of rare earth deposits. Evaluating the feasibility of a mining project is always a unique, sensitive and rather complex process that depends on multiple criteria.This paper focuses on clarifying the present and future global situation in the development of respective deposits and on identifying rare earth-specific criteria that influence the overall feasibility assessments of any potential (especially underground) mining projects. Environmental impacts, legislation issues and the presence of radioactive pollutants are some of the notable boundary conditions that govern rare earth mining operations and need to be taken into consideration. Furthermore, the balance problem between the supply and demand of the different REEs can determine decisively whether a deposit of specific REEs is economically exploitable. For this reason, evaluations are made regarding the future strategies to be enacted in order for the rest of the world to detach itself from this situation. The ultimate goal of these evaluations is for them to be incorporated in an overall assessment tool for rare earth underground mining procedures that will be implemented in real case studies to determine their sustainability.CITATION:Barakos, G, Mischo, H and Gutzmer, J, 2015. Status quo and future evaluations of global rare earth mining (with respect to special rare earth element-industry criteria), in Proceedings Third International Future Mining Conference, pp 21–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By H Ş. Duzgun

It is expected that the future of mines will heavily adopt autonomy. However, problems with leveraging workforce transition, meeting Sustainable Development Goals, SDG’s (poverty, reduced inequalities), managing uncertainties (geologic, operational, economic), cybersecurity (connectivity, cyber-physical infrastructure) and innovation (transformative processes, real-time decision-making etc) are required to be solved for the intended autonomy. These problems also impact the safety of the future mine environment. The AI technologies provide a broad range of opportunities for enhancing mine safety. However, development of an accurate AI model for mine safety requires a large number of data, which may not be readily available to overcome the associated uncertainties in the mine environment.

May 5, 2022

By W F. Bawden, J T. Paynter

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopes.

Jan 1, 1998

By S Matos Camacho, K G. van den Boogaart, R Tolosana Delgado, U Mueller

"The precise formulation of a geometallurgical optimisation problem is by necessity a simplification of reality. It includes implicit choices such as data availability or mining block geometry. Additional data can be orebody data, production data or market data. Often these choices are predetermined by the software, the workflow or the corporate culture, and as such are not even queried. There are several aspects that might play a role in the optimisation. They include not only the spatial model on which the selection of mining blocks and the potential mining sequence are based, but also the complexity of the processing model, the way in which uncertainty is treated, the scope of responsibility and the complexity of the model. In addition the timing of the optimisation and the availability (or lack thereof) of information will influence the outcome of any optimisation.We show that different modelling choices and different model formulations for the same mine can lead to very different processing choices, substantially different net present values (NPV), opposite investment decisions and so to overall different values for the entire operation. The selection of adequate simplifications and corresponding formulations for the optimisation problem is thus an important task in itself.For this purpose we introduce a method for quantifying the impact of certain simplifications prior to the optimisation. For example, the effect of mining block choices depends mainly on the spatial structure and the structure of the processing gain function. Both can be quantified beforehand. Based on the outcome, appropriate simplifications can be selected for the geometallurgical optimisation.CITATION:van den Boogaart, K G, Tolosana Delgado, R, Mueller, U and Matos Camacho, S, 2016. How Details of the Geometallurgical Optimisation Influence Overall Value, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C D. Strickland

Western Australia (WA) has been a significant world producer of titanium minerals (rutile, ilmenite and leucoxene) and zircon for over 55 years. In 2010, despite global difficulties, WA accounted for 12 per cent of world production for zircon, ten per cent for ilmenite, and eight per cent for rutile. With downstream processing, titanium minerals (ilmenite, rutile, leucoxene) and zircon exports for 2010 were valued at $511 M (Department of Mines and Petroleum, 2010).Production is dominated by two areas of the Perth Basin, namely the Eneabba and the Bunbury-Capel regions, which are located 240 km north and 200 km south of Perth respectively. Mineralisation is within Cenozoic beach or near shore dune deposits at three broad altitudes related to the present coastline, and two older higher sea-level still-stands. The titanium-zircon minerals presumably were derived from the underlying Mesozoic sediments of the Perth Basin. Contrary to expectations, age dating suggests that the ultimate source of most of this mineralisation was not the adjacent Yilgarn Craton. With the cooperation of industry, the Geological Survey of Western Australia has mapped all known significant titanium-zircon mineralisation within the Perth Basin. This mapping has identified ‘strategic mineral resource protection areas’ that should be set aside for future mining, ‘sterilised’ and ‘mined’ areas that generally do not restrict land use options, and ‘possible strategic resource areas’ which have exploration potential for hosting titanium-zircon mineral deposits.The Perth Basin is currently undergoing rapid residential and industrial development. By informing all stakeholders of the locations of potential mining areas, the titanium-zircon mapping has the ability to reduce future land use conflicts, and facilitate sequential land use planning. Appropriate planning measures are being implemented to ensure that the Western Australia’s titanium-zircon minerals industry remains strong and viable in the future.

Oct 5, 2011

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

By Miller RJ, Eager DT, Lama RD

For safe and efficient mining operations, it is essential that environment and equipment status be monitored. A system that gives quick access to status at any given time, and also permits quick analysis of their history, is required. Such a computer based monitoring system has been installed at West Cliff Colliery.The system is based on 2 super mini computers. Three major sub-systems monitor conditions in the longwall operations, environmental conditions in the intake and return roadways, status of the underground and surface installations, and mining and transport equipment.

Jan 1, 1985

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium.One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives. Controversy can always be achieved by producing a best of list; it can be guaranteed that everyone will disagree with at least one of the nominations. On this occasion, the best contributions by individuals or groups in a number of areas of mine fill technology, over the last 25 years, will be the basis for the nominal awards. The controversy can be increased by posing a number of questions that, hopefully, some of the authors will address during their presentations. I imagine the social functions will be busy enough, but the questions may just add to the cut and thrust of the debate.

Jan 1, 1998

By Jagger N. D

Lead residue from the Zinc Leach Plant at Pasminco's Port Pirie Lead Smelter was previously filtered on a vacuum drum filter and further dried in a gas fired rotary kiln prior to stockpiling and transport to the Sinter Plant. This process involved several materials handling stages, recycled significant amounts of zinc and often resulted in poor environmental conditions. These problems have been overcome by pumping the thickened leach residue approximately 450m to the Sinter Plant where it is filtered in a Larox Automatic Pressure Filter. The filter cake is discharged onto a conveyor belt, held in a storage hopper and then fed directly to the main sinter plant feed stream. Filtrate is returned to the process for additional zinc recovery. The laboratory and pilot plant filtration results are briefly discussed and compared with the operating plant data. The filter installation and ancillaries are described in detail along with the commissioning, operating and maintenance experience over the past 4 years. This installation has overcome the environmental and materials handling problems and resulted in annual savings of approximately $1 million.

Jan 1, 1989

By A Stasi, B Brice

Water is a limited and precious resource in Australia. Because of the increasing demand for water from all sectors of the economy and the variability in supply, efficient management of water resources is of vital importance. The national water reform agenda has provided a strong impetus to all states and territories to progressively move towards more efficient and sustainable water management. The Queensland Water Act 2000 is the legislative framework for providing water for the environment and for planning for the security of supply to water users. The comprehensive water planning process prescribed in the Act results in new tradeable water allocations that are separate from land. These water allocations are well specified and can be traded on a permanent or temporary basis. Trading of water allows it to move to its highest value use, thereby encouraging the most efficient distribution of this limited resource. In addition to transferring ownership of water allocations, it is also possible to change the attributes of the allocation, such as the location from which water may be taken. Changes to water allocations are subject to approval from the resource manager. Pre-testing allows for certain changes to be approved very quickly, making the trading process more streamlined and cost effective. Temporary trades, or seasonal water assignments, currently account for the majority of water trades in Queensland. However, permanent trading activity is expanding steadily as old water entitlements are converted to tradeable water allocations and as the market matures. The permanent trading market provides significant opportunities to the mining sector. It allows mining companies to buy water allocations at market prices without compromising environmental outcomes or causing third party impacts.

Jan 1, 2006

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

By G Barla

In Europe, a major interest in the infrastructure and tunnelling fields is in the new crossings of Alps in the form of base tunnels, which are important components of the high-speed (for passengers)/high-capacity (for freight) Trans European railway corridors. These tunnels cross the mountain belt at the elevation of the main cities and basins located all around the Alps and are longer (up to 57 km) and deeper (up to 2500 m) than all tunnels constructed in the centuries before. The excavation of the first Alpine railway and road traffi c tunnels could in general be carried out successfully by conventional excavation methods. With the great lengths of the new base tunnels, mechanised excavation by using tunnel boring machines (TBMs) is imperative as it contributes significantly to savings in construction time and costs. Questions are however posed on the adoption of such a systematic tunnel construction method given the severe ground conditions which are some time anticipated along the tunnel alignment, with possible major geological hazards such as water inflow in heterogeneous fractured or karstifi ed rock masses, stress-induced tensile failure of hard rocks, and plastic shear failure and squeezing of weak rocks, etc. This lecture is to briefly review the current state-of-the-art in the understanding and modelling of two such critical hazards as spalling/bursting and squeezing ground behaviour. With the present interest in the design of mechanised tunnelling with TBMs in such conditions, the complex interaction between the rock mass, the tunnel machine and its system components, and the tunnel support is studied in detail by numerical modelling. The research and development efforts presently underway with the intention to provide the designer with a novel three-dimensional (3D) simulator of mechanised tunnel excavation are presented. Case examples are discussed with reference to the Lyon-Turin Base Tunnel design.

Mar 8, 2011

The explosion at Appin Colliery on July 24th, 1979, demonstrated the need for a large scale facility to simulate an underground type explosion and study its effects. The effects of an explosion cannot be established quantitat- ively using small scale models. A gallery was constructed for this purpose at Londonderry Centre and commissioned in Feb- ruary, 1980. It is 50 metres long, 2.7 metres in diameter, capable of withstanding an internal pressure of 210 kPa and is the only facility available for this purpose in Australia. The gallery has provided valuable inform- ation on blast effects of explosions in tunnels and is to be used for testing the performance of explosion arresting devices, further invest- igation of explosion effects, research into basic explosion phenomena and instrumentation development. Additionally, it will provide a demonstration facility for training purposes.

Jan 1, 1981

By Sale M, Clarke R, Parker M

The Mount Gibson goidmine is located at the southern end of the Retaliation greenstone belt within the Murchison Province, approximately 300 km northeast of Perth, Western Australia. Economic gold mineralization occurs in the upper part of a Tertiary lateritic surface; its ultimate source presumably being Archaean greenstones. Gold is present in the laterite profile over a distance of 4 km in four separate prospects, from north to south, Mount Gibson Well, Midway, Orion and Tobias Find, the two last constituting the Mount Gibson mine. The area has'low relief. A low ridge to the west of the mineralized zone is formed mainly of rubble with minor outcrops of mafic volcanic and intrusive rocks. The terrain slopes gently to the northeast, and the maximum relief, in the vicinity of the mineralization, is about 20 m. The weathering profile comprises, from the surface: (i) soil, windblown sand or colluvium (thin), (ii) laterite; hardcap (including ferricrete and lesser silcrete and calcrete) is overlain by loose nodules and pisolites, and passes downwards into a mottled zone of variably ferruginized clay, (iii) clay; mainly pale brown, cream or yellow in colour, but in places contains relic quartz veins or dark ferruginous zones, (iv) clay with fragments of altered rock; normally grey to pale green in colour but sometimes includes an oxidized iron-rich horizon just above the weathered/fresh rock interface, (v) bedrock. The complete profile varies from 10-100 m thick, averaging 20 m. Zone (ii) is commonly 3-5 m thick. Loose pisolites of this zone fill cavities in the massive ironstone left by former tree roots, and cover irregular depressions which may represent former stream courses. Samples, representing 3 m intervals down the holes, have been collected from cuttings taken from rotary drill-holes along each of four traverses; one traverse at each-of the northern prospects and two traverses in the Orion part of the mine area. These samples have been submitted for X-ray diffraction analysis and for chemical analysis for a wide range of elements. Bedrock lithologies have been determined from microscope studies of bottom-of-hole chips.

Jan 1, 1988

By C Hertle, B Goebel, R Fabre

The mining industry maintains a ælove-hateÆ relationship with water. Dewatering, aquifer, water disposal, irrigation, process water, tailings water, run-off water, seepage, leachate and sumps are all terms that are used on a daily basis in the mining industry, highlighting the numerous water usages on site and their associated quality. According to the Australian Bureau of Statistics (2001), each year the mining industry consumes over 530 000 ML of water. The increasing recognition of water as a limited and valuable commodity, and the associated environmental concerns with the management of water disposal to the environment has led the industry into improving on-site water management. Progressively, water balance models and water reuse strategies are being developed, incorporating more sophisticated water treatment processes. By way of example, membrane technologies, once restricted to industries such as the pharmaceutical industry or the drinking water industry, are now entering the mining world with the aim of producing clean water of suitable quality for ore processing or for advanced treatment prior to release to the environment. This paper will provide a review of the threats and opportunities linked to water use and recovery/reuse in the mining industry in Australia. It will open with an overview of current water usage and associated quality for various mineral industries and continue with identifying the threats and limitations associated with the quality of available water. It will then present how newly developed water treatment technologies and assessment tools can be incorporated into the system to enhance the recovery and reuse of water on site, reduce the risks associated with securing long-term water supply and further improve production, environment and safety (health risk control).

Jan 1, 2006