Search Documents

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

The only functional underground Coal Mine in Nigeria is located in Enugu in Anambra State. For some years now the mine has been beset with a perenial problem of flooding. This has hampered produc- tion and some time ago the mine was abandoned. Recently money and equipment were made available to reactivate the mine. Attempts are now made to increase production as it is very much below demand. However, there are problems as the mine is below the water table under some major rivers and any advance exposes men and equipment to water surge. The paper traces the different attempts made to dewater the mine and the problems encountered in producing coal in this mine.

Jan 1, 1988

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By Lawrence M. J

It must be stressed that the following comments are offered only to assist mineral industry professionals in understanding the issues involved in personal liability. The information and views expressed herein are not intended to be a comprehensive guide or definitive statement of the law and they should not be regarded as a substitute for specific advice for individual situations. Readers should consult their own legal and other professional advisers before applying the content of this paper to their own particular circumstances. It is hardly news that work in the mining industry is governed by a complex regulatory and legal system which is constantly changing, but few realise just how directly they can be affected and become personally liable for any breaches. These may result in civil or criminal proceedings and personal assets are at risk. Owners, company directors, managers and now employees are at risk, together with consultants, contractors and suppliers of equipment or consumables, as well as government inspectors. They are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control. This paper identifies the areas where such individuals in the open pit mining industry in Australia face the risk of personal liability and measures which can be used to minimise the risk or which can be used to make out a defence to legal action which could arise. There have always been a myriad of Commonwealth, State and Local Government laws and regulations with which to comply, and now international protocols are being used as a basis to impose greater obligations on all people. Once, the `corporate veil' gave some protection to the individual, but today there is negligible protection from the full force of the law. Not only are there various types of law enforcement officers, but public interest groups, shareholders, customers, suppliers, creditors etc may litigate. This paper is not intended to be an exhaustive discussion of the provisions of all the legislation or case law where individuals can be held) personally liable. These areas would include environmental, pollution and heritage law (including Aboriginal sacred sites); occupational health and safety (including workers' compensation) law; trade practices and fair trading law; contract law; corporations law (including the requirements of the Australian Stock Exchange [ASX] and Australian Securities Commission [ASC]); industrial relations law; anti-discrimination and sexual harassment law; taxation (including superannuation trustee) law; and the Common Law. The focus is on the following areas of regulation, which are outside the usual experience of those in the open pit mining industry (the Mining Acts and Regulations are specifically not dealt with here): ò Environment Law; ò Trade Practices Law; ò Occupational Health and Safety Law; and ò Corporations Law.

Jan 1, 1994

By A Scott

Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data û especially with semi-automated data acquisition by instrumented mine equipment. However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model. An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc not only have many areas of interest but also have very different conceptual models by which they evaluate performance. It is too ambitious to attempt to bring all of these cultures together û in a single step. However, the success of the Mine to MillTM project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from orebody model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is strongly focused on the technical requirements û not on the business model. This paper considers how to define at least some of the key decision points in terms of some case studies. Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning.

Jan 1, 2002

By O N. Antzutkin, A V. Ivanov, W Forsl

Polycrystalline and surface complexes (at synthetic sphalerite, ZnS, and galena, PbS) of zinc(II) and lead(II) ions with eight different O,OÆ-dialkyldithiophosphate (Dtph) substances have been prepared and comparatively studied by means of 31P CP/MAS NMR spectroscopy. The 31P resonances have been assigned to dithiophosphate groups with terminal S,SÆ-chelating or bridging coordinations in the mono-, bi-, tetra- and polynuclear complexes respectively. The bridging coordination of two neighbouring zinc(II) ions by O,OÆ-dialkyldithio-phosphate ligands was established at the surface of synthetic sphalerite.The adsorption mechanism of dialkyldithiophosphate on synthetic galena includes formation of a surface complex as well as surface precipitation. Principally different coordination modes of the reagent were discovered at the surfaces of galena and sphalerite (ie terminal S,SÆ-chelating coordination to the lead atom).Derivatives of monothiophosphoric and phosphoric acids were displayed as hydrolysis products of dialkyldithiophosphates at synthetic PbS.

Jan 1, 2005

P.IISTRACTThe Pacific Rim is advantaged by the uniqueness and diversity of its geological features. Why then is geology given so little regard in the education systems of the countries of this region? Not that these countries differ greatly from those in other parts of the world. Papers presented during the Precollege Geoscience Education session at the 28th International Geological Congress (28th IGC) held in Washington, July, 1989, indicated strongly that the problem is universal. There is a marked decline in interest in the Earth sciences and many nations are looking towards methods that might change this trend. Problems affecting geological education include the lack of purpose and direction, its obsolete curricula and the difficulty in attracting gifted students.The world-wide plight of geology comes at the very time when it should be fundamental to a public understanding of the global effect of human population pressure. There is a universal awareness of "the environment" but very little awareness of the science that has supplied most of the data. Geology, as the science of the Earth, is of paramount importance to an understanding of our life on this planet, particularly in its role as the source of our every need.

Jan 1, 1990

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

We all live in professional silos û comfort zones, where we talk to like-minded people with the same training, experience and view of the world. We note in passing the existence of other disciplines, but they are tolerated rather than embraced. To the geologist, the metallurgist is a mad scientist conjuring gold out of some foul solution about which the less said the better. To the metallurgist, the geologist is a bearded, self-appointed sage who guesses what is under our feet by sniffing the air, and drives a Land Rover badly. As to the view of mining engineers held by both geologists and metallurgists, this is best left to the imagination. And of course we are all confused by the term æmetallurgistÆ. I am called a metallurgist though my skills are in mineral processing not metal processing, but I canÆt be called a mineralogist because that definition is already taken. *Please note that this is available as an extended abstract only*

Jan 1, 2005

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

The Nelson province was chosen as the prime area for rhenium sampling, based on its mineral associations. Sample preparation involved benefication by grinding and flotation A modification of published procedures for rhenium analysis was developed and the results compared with those obtained for molybdenum on the same samples using atomic absorption spectroscopy. The results of the analysis for both metals is discussed and the relationships between rhenium and the molybdenum mineralisa- tion of this region is commented on. A metal- 1ngenic province is defined for molybdenum and r'.ienium and the tectonic setting for this is discussed. Some consideration has been given to rhenium possibilities in Fiordland and the Coromandel Range.

Jan 1, 1980

By Hanes J

More than 200 bursts in coal occurred at Leichhardt Colliery prior to December 1978 during mine development in the 6 m thick Gemini seam at depths approximating 400 m. Three large bursts each displaced more than 300 tonnes of coal and stone. Two of these which occurred in continuous miner developments, are described and compared. Geological settings, mining strains including induced cleavage and roof failures associated with bursts are described. A shotfiring technique replaced mechanised mining following a major incident at the colliery. Present mining procedures, the apparent improvement in stability of workings and ongoing geotechnical monitoring programme are discussed.

Jan 1, 1980

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

By Tonks E. E

The earliest discovery and mining of coal in the northern area of the Greta Coal Measures at Anvil Creek in 1862 was by William Farthing, however, some official records attribute the discovery to Thomas Frost in 1864. Frost's discovery was examined by William Keen, government examiner of coalfields, and further prospecting was carried out. This was followed by the pioneering work of C S Wilkinson, government geologist in 1884. Subsequently in 1886 C S Wilkinson entrusted a detailed survey of the coalfield to the then geological surveyor, T W Edgeworth David.The outcrop of the Greta Coal Measures around the Lochinvar dome was mapped by Edgeworth David and as soon as he reported his discovery, the Department of Mines reserved in the interests of coal mining an area of 23700 acres, which extended between what became the South Greta and Abermain No I Collieries.

Jan 1, 1993

By L M. Lobato, J C. S Seoane, F J. Baars

The Carajßs Province presents several volcano-sedimentary sequences that comprise the Itacai·nas Supergroup. The rocks represent bimodal volcanism, and clastic and chemical sedimentation in relatively unstable basins subject to recurrent structural events with subsidence and volcanism. The Grpo Parß Group represents one of these sequences with mafic volcanic rocks that enclose discontinuous jaspilite lenses, with development of large high-grade orebodies (Fe >65 per cent). This unit is named the Carajßs Formation and presents peculiar characteristics compared to other iron districts in the world, thereby departing from the classic Lake Superior or Algoma iron formation types. Owing to the dense vegetation, lack of outcrops and harsh landscape, the structural analysis of the district can only be accomplished by combination of regional field work, detailed structural work on the open pits, and remotely sensed image interpretation, in this case Landsat ETM7, JERS-1 images and the SRTM digital terrane model. The regional trend of the several sequences of the area is approximately N-S and the structure is dominated by a flattened flexural fold system with axes moderately dipping WNW, intersected by several strike-slip faults subparallel to their axial plane. The Serra dos Carajßs represents an s-shaped synform-antiform pair, herein named the Carajßs Fold. This regional structure is partially disrupted by the Carajßs Shear Zone that divides it in the northern (Serra Norte) and the southern (Serra Sul) Ranges and also probably prepared the terrane with the development of pathways for mineralising hydrothermal fluids forming large high-grade massive iron bodies. Syntectonic granitic bodies played an important role in the structural evolution of the area as well. They caused localised ductile flattening deformation and thermal contact metamorphism in surrounding terranes. The Estrela pluton, for instance, was responsible for the discontinuity of the regional trend between the Serras do Rabo and Leste. The Carajßs Province is regionally the upper crustal product of a very shallowly eroded dome-and-keel geometry of Neo-Archaean volcano- sedimentary units intruded by syntectonic calc-alkaline intrusives and overlying pre-existing infracrustal rocks. The lithostructural data suggest continental-margin back-arc basin development and closure in an oblique collision belt, with N-S shallow crustal shortening, parallel to the inferred pre-existing strike of the stratigraphy.

Jan 1, 2005

By J Palaci, M MelTndez, F Parra, I Rojas

At the Huasco Pellet Plant of Compa±fa de Aceros del Pacffico, Chile, the production of iron concentrate suitable for pellet feed from a low-grade iron ore was technically evaluated. In this study, three treating schemes including comminution, magnetic concentration and flotation in pneumatic cells were tested. The best results were obtained at the laboratory scale by flotation technique using Lilaflot D 817 M as the collector without using any depressant. The operational parameters were determined including pneumatic flotation, and three circuits, two including magnetic pre-concentration, with the low-grade iron ore. The best results were obtained by size reduction at 80 per cent under 325 Tyler mesh, three steps of magnetic concentration and three steps of flotation in pneumatic cells. The magnetic concentrate contained 63.02 per cent of iron and 6.6 per cent of silica, and after the pneumatic flotation the iron content increased up to 70.18 per cent and silica decreases to 1.07 per cent with 78.78 per cent of iron recovery at a weight recovery of 31.89 per cent. Therefore, it is possible to use low-grade iron ore to produce pellet feed from magnetic concentrates by using reverse iron flotation in pneumatic cells.

Jan 1, 2005

The New England Fold Belt forms the easternmost and youngest section of the Tasman Fold Belt System of eastern Australia. From middle Palaeozoic to Early Cretaceous time it was the site of extensive episodic calc-alkaline magmatism related to W-dipping subduction. The oldest rocks may have formed at least partly in a volcanic island arc, but from the Late Devonian, the fold belt developed as a convergent Pacific-type continental margin. For Late Devonian-Carboniferous time, parallel belts representing continental margin volcanic arc, forearc basin and subduction complex assemblages can be recognised. Major dextral transform faulting may have offset parts of the fold belt in the Late Carboniferous. In addition, some structural blocks which appear to be out of place in the overall palaeogeographic setting are possible exotic or suspect terranes. A great variety of lode deposits ranging in age from middle Palaeozoic to Early Cretaceous is present in the New England Fold Belt. The vast majority of these are related to emplacement of extensive granite plutons and eruption of continental silicic volcanics in Late Permian-Late Triassic time. However, volcanogenic massive sulphides and volcanic hosted epithermal gold-silver deposits in older rock sequences include one major orebody (Mount Morgan) and several important ones (Mount Chalmers, Cracow, Silver Spur, Cangai and Halls Peak). Some problematical deposits are best classified as metamorphic-hydrothermal. These include gold-bearing quartz reefs and stockworks in sedimentary host rocks, the most important of which are at Gympie, and antimony-gold- tungsten mineralisation in the New England area, mainly at Hillgrove.

Jan 1, 1987

By Just G. D

The results of a geostatistical analysis of geochemical data obtained from field measurements are described in the paper. Q values derived from seismic signal rise times for different travel paths in the rock masses were used in the study. Cross-hole seismic measurements made at surface and underground sites formed the basis for the work. Geostatistical estimation of average l/Q values for area of the rock were compared with geological interpretions of rock type distributions. Reasonable correlations were obtained between the two methods of rock quality estimation.

Jan 1, 1988

By J Centofanti, D Conti, R Riske, C Morley, A Cook

Why is it so difficult? Why are there differences throughout the resources industry in how reconciliation factors are reported and calculated? Why is there no standard formula to use? These are common questions asked when mining companies try to compare reconciliation results across operations or attempt to undertake internal or corporate governance reporting processes. For many mining companies the calculation of reconciliation factors is often a very time and resource intensive part of mandatory reconciliation reporting. Some major mining companies, that move millions of tonnes of material per annum, dedicate full time resources to the calculation of reconciliation factors. The willingness of these companies to set aside resources demonstrates the value that operations place on good reconciliation reporting. Reconciliation is about measuring the variance between two like measures at different points along the mining sequence. It can be undertaken between predictive models, forecast plans and actual measured performance. Calculations are used to derive a variance between two sections within the mining sequence, with the result being commonly known in the resources industry as a æfactorÆ. Mining companies use the calculation of reconciliation factors as key performance indices (KPIs) to provide a æhealth checkÆ of their operation, with variances often pointing to issues either with the accuracy of the original estimate or the quality of the measurement being used in the comparison. There are many reconciliation factors that can be calculated and reported. This paper will set out, clarify and provide a recommended standard means of calculating each specific factor that, where adopted by a company, will ensure compliance with the international reporting codes, such as JORC. Using case studies from Rio Tinto Group (Rio Tinto) and BHP Billiton Mitsubishi Alliance (æBMAÆ), and the authors experience across a wide range of mine sites, the outline of a generic solution for tracking a parcel of material from the pit through to the port along with appropriate reconciliation factors is provided. The intention of proposing standardised reconciliation factor terminology and methodology is to provide the foundations of a system to enable communication and comparison across different commodities, companies and mines sites.

Jan 1, 2009

The efficient design of carbon-in-pulp (C.I.P.) plants involves the integration of both process engineering and design engineering.Many recently constructed plants have not recognised the above interrelationship, and as such have incurred higher capital and operating costs than were in reality necessary. This has been compounded in some cases by slavishly following the design of plants where process conditions are different for the ore characteristics in question, thus perpetuating design errors that finally become industry "accepted practice".In the paper that is to be presented the unit operations of crushing, grinding, classification, leaching, adsorption, desorption and electrowinning in C.I.P. plants will be discussed with reference to the integration of process and design engineering.

Jan 1, 1986