Search Documents

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

The planning, design and construction of a service tunnel, under a major arterial road between two hospitals are described. The multiple uses of the tunnel combine to provide a favourable cost-benefit ratio for the tunnel as part of a rationalisation of services between hospitals. The driven tunnel provides economic, program and approval advantages over that of a cut and cover construction. The cross sectional shape of the tunnel was determined during feasibility studies by the degree of weathering of the Silurian mud- stones, the shallow cover and the proposed excavation equipment as well as the functional requirements. The site investigations covering geotechnical, building, noise and level surveys provided input to the design documentation and construction phases. Monitoring of settlement levels and primary support stresses during early construction stages confirmed the adequacy of the proposed tunnelling methods and support to be used adjacent to the major building foundations. The 140 metre long tunnel was success- fully completed in April 1980 at a cost of $650,000.

Jan 1, 1981

By T Soares, P Esteves, C Senna, V Souto, E Dias

Steinert provides a wide portfolio of Sensor Based Sorting (SBS) technologies, including the possibility to combine different sensor data in the development of the separation applications. This multi sensor approach provides a larger applicability and extensive flexibility for the technology. This effect is emphasized for mining applications, once every ore body presents its own features that can also comprise a large material variability. In this sense, every sorting application is customized and comprises a personalized solution. This means each project development includes a test work stage that approaches from the project discussion, test definition, up to test outcomes and processing development. In relation to very complex and large projects, a sorting pilot scale plant has become a crescent tendency. By having a pilot plant stage can represent a chance to test larger amounts of material from different mining areas, different mining projects, such as to consider different processing targets and application approaches. Based on that, a better understanding about the technology application can guide a more assertive development of large and complex ore sorting projects. The aim of this paper is to provide information about the applicability of the Steinert multi sensor technology at different pilot plants in South America. It consists in a compilation of laboratory test results, plant design and operational results. For that, a chromite, an IOCG deposit and a sulphide gold ore projects are presented. Additionally, the paper discusses the application of different sensor technologies combinations such as various processing targets, thus providing a wider understanding about sorting applications and flexibility.

Nov 10, 2020

By S Dykes, R J. McCarthy, B Klein

There is growing interest in the mining industry on the application of ore sorting. While many are familiar with particle sorting, including the limitations that technology presents (e.g. throughput), bulk sorting, with its higher throughput potential, is less understood. Despite the potential to sort at higher throughputs, few operations have adopted bulk sorting processes, certainly not at large scale. It is suggested that the inability to reliably predict outcomes from bulk sorting may be limiting its adoption in mining projects. Consequently, an evaluation approach for bulk ore sorting has been developed such that mass pulls and grade upgrades can be predicted in the context of a mining study. The approach allows for evaluation of drill core assays and application of the consequently derived heterogeneity relationships to the block model for estimation of sorting outcomes. These processes were applied to conveyor-based bulk sorting for the CuMo project in Idaho, USA and are described in this paper.

Nov 10, 2020

By J Player, G Sweby

The material properties and hence performance of saturated alluvial sediments slope can be incorrectly forecast if the water content is not preserved, and materials properties not correctly determined. The occurrence of saturated sediments in the Western Australia (WA) Goldfields, while not common, should be a significant investigation focus. Geotechnical engineers new to the area may be unaware of this and hence the importance of correct testing and determination of the material strength. Application of appropriate analysis to determine stable pit slopes to an acceptable level of risk, is not possible unless the appropriate strength and hydrogeological parameters have been established at the outset. A back analysis is presented of a pit that had extensive slope failures in alluvial clay-rich sediments with discussion on the approach adopted by the original design engineers to assess pit wall stability and consequent poor slope performance. Learnings from a full pit 3D back analysis are presented, with an approach to geotechnical and hydrogeological investigations and analysis for slopes in similar materials.

Jun 22, 2022

By Mingmin Dou

The behaviour and deportment of indium during the precipitation of sodium jarosite from Fe2(S04)3 - Na2SO4 solutions were investigated. Indium is readily precipitated with sodium jarosite, and the extent of In precipitation increases as the In concentration of the solution increases. It was shown that In 3+ substitutes for Fe 3+ in the jarosite structure to form a nearly ideal solid solution series. On a molar basis, the precipitation of Fe is slightly favoured over that of In, and the difference is reduced as the pH increases. Sodium jarosite precipitation becomes kinetically rapid at temperatures >70¦C, but increasing temperatures in the range 70 to 150¦C affect neither the relative precipitation of In and Fe nor the composition of the jarosite product. Low Na2SO4 concentrations result in reduced product yields and jarosite precipitates in which H3O' > Na+. The hydronium-rich precipitates have reduced In contents. Increasing the ZnSO4 concentration of the solution slightly increases the quantity of jarosite formed and results in the incorporation of -0.3 per cent Zn in the jarosite structure. Otherwise, the presence of ZnSO4 has no significant effect on the composition of the jarosite. Seeding accelerates the rate of jarosite precipitation but has a negligible influence on the deportment of In. The jarosite precipitation reaction at 98¦C is relatively rapid and near-steady state conditions are achieved in - 6 h even in the absence of seed. The initially precipitated jarosite is slightly enriched in In with respect to Fe. The ferric ion concentration of the solution has a significant influence on both the amount of jarosite formed and its composition. In particular, the jarosites precipitated from dilute Fe3+ media have significantly enhanced In contents. Hence, it may be possible to recover - 25 per cent of the dissolved In, at the 1000 mg/L level, in a jarosite precipitate assaying - ten per cent In by the controlled oxidation-precipitation of sodium jarosite from a ferrous sulphate processing solution.

Jan 1, 1993

By Forssberg KSE

The behaviour of cationic and anionic collector mixtures in the feldspar-quartz flotation system has been investigated througl conductivity, surface tension, zeta-potential and flotation studies. Tht results show the formation of molecular complexes between oppositel; charged collector ions through charge neutralisation. The molecular complexes are found to have a higher surface activity than the individua components. The mole ratio of the mixed composition is found to have, significant effect on flotation. Mole ratio less than unit} (anionic/cationic) of collector mixtures increases the flotation recoveries If the mole fraction of the anionic collector is greater than the moh fraction of cationic collector in a mixed composition, flotation ceases The flotation selectivity principally depends on the inherent differences it the surface charges of feldspar and quartz at the flotation pH values of

Jan 1, 1993

By R Burgess-Limerick, J Haight

A review of mining automation experiences was undertaken on behalf of the National Institute for Occupational Safety and Health (NIOSH). The research included a review of literature and guidance materials; analysis of automation related incidents and visits to surface and underground mines in Australia, Brazil, Chile, South Africa, Sweden and the USA.

Apr 16, 2024

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Field

Kimberlite pipes, as opposed to dykes, sill and secondary deposits, are the primary target for diamond exploration companies because they have simple geometries and can contain large volumes of potentially diamond-bearing ore. Once discovered, important decisions have to be made regarding the sampling of these geological entities to establish the total volume of ore present, and to define the internal geology, which can be complex in nature and controls the distribution of diamond grade. It is essential that as part of this process the uncertainty in constructed geological models are assessed. In this paper the Orapa AK1 kimberlite pipe in Botswana is used as a case study to explore a potential methodology for defining this uncertainty. The uncertainty of the rock volumes of different types can be characterised by a geostatistical approach. Geostatistical simulations, based upon a plausible representation of the geological bodies, provide different possible images of the orebody that can be considered as different realities. By testing different borehole layouts and drilling the orebody virtually on the computer, many different, but equi-probable realisations of the pipes can be produced. It is then possible to estimate the rocksÆ volumes and compare them with the actual ones. A statistical analysis of the relationship between estimation error and the number of boreholes can then be used to optimise the next sampling campaign. The rock volumes are obtained from a two-step simulation process. Firstly, the pipe geometry is simulated by means of introducing variations around the geological block model, by an original method called centre point simulation (CPS), which has been developed for this purpose. Secondly, the internal geology is then simulated within the pipe. The methodology for simulating the internal geological zones has to be adapted to the level of information and to the geological structure itself. The upper portion at Orapa AK1 is filled with sedimentary crater facies. Here plurigaussian simulation techniques can be applied that are adapted to the simulation of sedimentary facies. The central zones of the pipe are typically subvertically-oriented massive volcaniclastic deposits and breccias and the lower regions comprise a complex root zone. CPS is appropriate for these zones.

Jan 1, 2006

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of >6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By F Flitti, M Haest, O Dominguez, D Mittrup, G Hird

The automated geology interpretation (AGI) tool has been developed in BHP Billiton to automate stratigraphy logging of drill holes, using any available quantitative data sets. At present, AGI is set-up to utilise geochemistry and mineralogy from infrared spectroscopic data to predict stratigraphy. Once the AGI tool is calibrated, results show that the tool is capable of automatically defining stratigraphy across all of the deposit types, encountered by BHP Billiton Iron Ore in the north-west of Western Australia. Accuracy of AGI at predicting stratigraphy is on average better than 75 per cent, with average accuracies exceeding 85 per cent for some deposit types. The AGI tool can deliver fast, accurate, consistent and objective geological interpretations.AGI is currently being implemented in BHP Billiton Iron Ore Exploration to streamline the drill hole logging process and allow geologists to spend less time defining stratigraphy at the drill hole level and more time investigating stratigraphy in 3D. This will deliver improved geology models, with significant downstream benefits in terms of better resource models, more accurate mine plans, higher plant efficiencies and more consistent ore products, driving productivity in BHP Billiton Iron Ore over the next decade.CITATION:Mittrup, D, Flitti, F, Hird, G, Haest, M and Dominguez, O, 2015. Semi-automated geological interpretation using assay and infrared spectroscopic sensing parameters towards improvements in geological modelling, in Proceedings Iron Ore 2015, pp 313–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A G. L Pratt, J R. Grant

Mining companies face the ongoing challenge of sustaining and growing production. This paper outlines business investment concepts to grow reliable returns on investment from a portfolio of choices by:improved visualisation, diagnosis and tune up of the investment pipeline (pipeline management); good corporate decision making (governance) to select the right project mix, risks and sequence; and delivery strategies to enhance and reliably execute projects.

Jan 1, 2006

By T Martin, M Martin

Mining of sulfide-based ore deposits typically creates a potential for release sulfate and acid to groundwater, and many operating mines are thus predicted to require long-term post-closure treatment of groundwater. Toward the goal of selecting an optimal treatment, this paper compares costs of four demonstrated technologies for long-term treatment of sulfate-contaminated groundwater: in situ biological reduction (ISR), in situ permeable reactive barrier (PRB) composed of compost and zero-valent iron (ZVI), and two ex situ æpump-and-treatÆ technologies ù ex situ biological reduction, and ex situ nanofiltration with lime precipitation. Costs for each technology are estimated for treatment of a model aquifer system containing sulfate-contaminated groundwater, with the goal of treating 1 m3/min of groundwater from 1500 mg/L sulfate to a target level of 500 mg/L. (Metal removal is typically achieved by these technologies, and thus excluded from this analysis.) Costs are estimated for each technology as a function of treatment duration (ten to 60 years) and, for PRB and ISR, required replacement frequency (ten to 60 years). Estimated costs include capital and operation and maintenance, using a seven per cent net discount rate. Results indicate that ex situ technologies (biological reduction and nanofiltration with lime precipitation) are the most expensive. In situ technologies may be much less expensive, with PRBs having by far the lowest potential cost, followed by ISR as the next least expensive. However, actual costs for the in situ technologies are very sensitive to poorly constrained parameters, particularly the ZVI content of the PRB, and the effective life of PRB and ISR systems. This large cost uncertainty supports delaying remedial actions where viable, and suggests that feasibility analyses are generally warranted for specific applications to focus on these sources of uncertainty.

Jan 1, 2003

By J S. Simmons, J G. Skousen

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalised according to construction cost, projected service life and kilograms of acid load treated. Results were dimensioned as $/kg of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

Coal losses and dilution are among a coal mine operators everyday problems. These losses and unwelcome additions are generated primar- ily by the stripping operation and secondly by the coal mining opera- tion. Losses in yield due to preparation plant efficiency are a separate issue although they may be related to the coal mining operation. The losses and dilution can be traced to the following operations: (A) Overburden or Interburden Removal (1) Removal of coal edge by blasting operations. (2) Removal of top of seam by drilling/blasting. (3) Removal of top of seam by stripping equipment. (4) Removal of coal edges by stripping equipment. (5) Dilution due to stripping equipment. (B) Coal Mining (for the case where seams are ripped rather than shot) (1) Coal rib losses. (2) Coal rib dilution. (3) Coal left in floor. (4) Coal left in fault areas. (5) Floor material picked up whilst loading. (6) Spoil material picked up. (7) Spoil material from poor surface clean up. (8) Top of coal losses from final clean up. (9) Dilution from ripping too deep, i.e. into floor below seam. (10) Dilution from interseam parting. The losses apply to both the single seam and multi seam oper- ations although they are more pronounced in the multi seam mines than in a single seam mine due to the position of the coal which is lost. For example in the multi seam case the top seam coal edge loss is final. There is little chance of recovery with the subsequent pass even if the extra rehandle is done. However conversely the lower seam is relatively easy to locate as it has nowhere to go being contained by the lowwall bench.

Jan 1, 1988

Porphyry type mineralization of Lower Cretaceous age in eastern Queensland has been recognized only from the easternmost part of the northern New England Orogen (Day, Murray and Whitaker, 1978), within the northern Yarrol Province (Horton,1982). Recent work about the Mt. Suthers (Pb, Zn, Ag, Cu, Au), Lug-e-nor (Cu, Pb, Zn, Ag, Au, Mo), and German Tully (Cu, Au, Bi) prospects suggest that there has been a phase of porphyry type mineralization within the Gympie Province, of Lower Cretaceous age, overprinting earlier Permo-Triassic phases. About the Mt. Suthers Prospect surface samples of shallow, medium to heavy textured soils derived from marine sedimentary rocks of Permian age, and extrusive and intrusive igneous rocks of intermediate composition and Triassic age, were analysed for Cu, Zn, Pb, Co, Cr, Ni, Fe, V, Mn and Ag. Whereas strong iithological control determined the distribu- tion of Cu (diorite) and of Cr, Ni, Fe and V ,sedimentary rocks), the distribution of Pb, Zn, Ag and of Cu, were determined by mineralization of faults by a cavity fill hydrothermal process. Gold is associated with the Pb, Zn, Ag mineralization. Co and Mn showed distributions independent of lithology and structure. The fault controlled style of mineraliz- ation at Mt. Suthers is repeated at other localities to the south; Calgoa, Marodian, and German Gully. Relative dating of structural features and isotopic dating of nornblende porphyrites (134-135 m.y.) near and related to those mineralized at German c;ully suggest a previously unrecognized phase of porphyry copper style mineralization in south-east Queensland of Lower Cretaceous age (Fig. 1).

Jan 1, 1987

By A Castleden, G Cavanough, M Kochanek, J Cunningham

ROES« is a proposed new mining system for underground hard rock mines. Ore is accessed from within a shaft, which is located close to or within the stope, and pitched either vertical or within approximately 20 degrees of vertical. The shaft is designed to exclude personnel entry so production drilling and explosive placement is done using remotely controlled or automated machines. Routine remotely controlled survey of the shaft, stope back and broken rock within the stope is typically done following each blast. The survey may include excavation geometry, rock fragmentation and geotechnical characteristics. Blastholes are surveyed before placement of explosives. This provides mine operators and engineers with real-time data, allowing them to monitor production performance and risk factors so that they can make rapid changes as required. ROES« is designed to apply to open stoping or sublevel caving situations either in disseminated, geologically defined, thick tabular or narrow vein orebodies. The technologies developed for ROES« will also have potential applications to block caving operations to reduce the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES« will reduce the amount of stope-associated development by about half and therefore will allow ore to be brought on-stream sooner and at significantly reduced cost. Other savings are expected to flow from the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity. CSIRO and Orica Mining Services are developing the required technology and AMIRA is seeking sponsorship for a project to trial the mining method. This paper details the ROES« method, expected benefits and applications and includes typical stope and mining block designs and design requirements.

Jan 1, 2008

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985

By D Henderson, M Germain

The beneficiation of iron ore deposits to yield haematite and magnetite concentrates for steel making processes typically require the use of one or a combination of wet processing techniques based on gravity, magnetic or froth flotation processes. With the need for more cost-effective technologies with a lower water demand, a re-examination of dry processing techniques has been initiated. For example, a dry processing capability may offer an advantage where suitable quality and quantity of process water hinders the development of a particular resource. This paper describes recent laboratory test work for the production of high grade concentrates using dry electrostatic techniques for -300 ¦m haematite and magnetite ores and compares them with magnetic separation techniques.

Jan 1, 2009