Search Documents

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Bevilacqua P, Preti U

The basic separation phenomena taking place in film concentration processes are studied through a kinetic-probabilistic approach. This approach is based on the fact that the particle velocity in the film separation phenomena is a random variable and may be defined by frequency distributions and probability laws. The approach requires: 1. development of probabilistic models for describing the behaviour of particles having different specific gravity and size along selected trajectories in the separating devices; 2. setting up an experimental procedure for determining the relevant frequency distribution curves at the exit of the separators for the particles mentioned above; 3. estimation of model parameters and model validation. In the paper, the model equations are given for the mass distribution of particles on the surface of separators, the mass distribution at the exits of shaking tables and the residence time distribution in channel type devices. The relation between residence time distribution and particle velocity distribution is derived. The test procedure has been defined and results are reported for the exit or residence time distribution in channels. A comparison between experimental and calculated frequency distributions is reported.

Jan 1, 1993

By Bragg R, McMahon B, Lenton R

In 1992 environmental audits were carried out at seven coal mines operated by Oakbridge Limited in the Hunter Valley and Lithgow areas of NSW. The audit reports recommended a course of action designed to improve the environmental management system already in operation at the mines. This program started with training in environmental awareness for the Board of Directors, and the development and authorisation of an environmental policy. On-going programs at each mine were expanded to include environmental awareness training for all 2000 employees at the mines, and the development of a 20-module environmental training program which included air, water, soil and noise management, oil and chemical handling, sampling and monitoring, rehabilitation techniques and many more. Environmental incident reporting was introduced, and a system of reporting from the coal face through individual mine site environmental committees, to a Corporate Environmental Committee and up to the Board Environmental Committee became an effective part of a due diligence program. The Board resolved to undertake external independent environmental audits every two years, with internal reviews in the alternate years. An Environmental Management Group was formed, consisting of four internal environmental personnel and Oakbridge's appointed environmental consultant, to effectively resolve many of the environmental issues facing the Group. This program is continuing to evolve as an industry leader in environmental management Practice.

Jan 1, 1995

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

Since the mid-1970s there has been increasing attention in the South Pacific area to the problems of disaster planning and management at various levels, mainly from regional through national to provincial levels. This concern has been expressed in a variety of ways. International aid donors have made their views known in commentaries or reports. Seminar discussions have been organised at the regional level (such as at Suva, 1976; Suva, 1979; Tonga, 1982 and Suva, 1983). In-country training workshops or meetings have been organised (such as the "Disaster Preparedness Workshops for Non-governmental Organisations" in Pacific countries, jointly run by the Australian Red Cross and the Australian Overseas Disaster Response Organisation and supported by AIDAB, in Vanuatu, 1985; Solomon Islands, 1985; Western Samoa, 1986; Fiji, 1987; Tonga, 1987; Lae and Port Moresby, Papua New Guinea, 1988) or held outside the area (ACDC at Macedon, 1981). Training and/or research institutions have been established such as the East-West Center, Honolulu, and the Asian Disaster Preparedness Center, Bangkok (more Asia oriented). As part of the East-West Center Pacific Islands Development Program's Disaster Preparedness Project, a detailed manual of disaster preparedness and response procedures and guidelines has been published (Carter, 1984).Table 1 and figure 1 show that the area with which this discussion deals is a highly fragmented island region, comprising many small, some minute, nations, both in land area and population. The social structure is predominantly rural, with the capital city often making up a small part of the total population and, in absolute terms, little more than a small town. Outside the administrative and governmental activities concentrated in the capitals, in most cases the indigenous inhabitants depend on subsistence agriculture or on usually a monocultural concentration on a cash crop, most frequently coconuts.

Jan 1, 1990

By R Lloyd

Coal Services (Health and Safety Trust) funded ARRB Transport Research Ltd to investigate fatigue and performance of truck drivers over consecutive shifts. The main questions were to assess: What is the most important contributor to acute fatigue in mining? Is it length of shift (eg eight hours versus 12 hours) or is it time of day (eg circadian effects)? What is the limit of successive day or night shifts before chronic fatigue affects operator performance in open cut mines? The project methodology included utilising ARRB Fatigue Monitoring Devices (forced-choice stimulus reaction) in eight haul trucks, testing 24 subjects over several weeks. Each subject filled in a Fatigue Risk Questionnaire on lifestyle and health. Operators worked a 14-night, one day off, 13-day roster of 12-hour shifts in a fly-in/fly-out operation with excellent opportunities for restorative sleep between shifts. A total of 3500 hours of real-time data was collected, representing the first set of objective, real-time driver performance data for Australian mining. The data showed that for a single night of driving haul trucks, there appears to be no effect on operator fatigue from the amount of time on task (for the 12 hours). In fact performance was worse through the first eight hours than the last four. The circadian influence had a stronger affect than working more than eight hours. Of the 14 nights worked at the site, nights 13, 14, seven and two respectively, were the worst. This presents a conundrum for policy makers who may like to place caps on working hours or rosters in the hope that it will alleviate the fatigue issue. It will not. The major finding within this study is the combined influence of circadian rhythms (human body clock) and individual variability on performance. The lifestyle habits and the health of individuals have a profound effect on operator performance as shown by the strong positive correlation between high fatigue risk scores from the Fatigue Risk Questionnaire and poor performance. An individualistic approach would appear to have the best chance of reducing high potential incidents due to fatigue through successive nightshifts.

Jan 1, 2005

By I Testrow, M Wiggin

Scrutiny of the whole explosives industry has increased as a result of the terrorist attacks on the World Trade Centre and the Pentagon on 11 September 2001 and the bombings in Indonesia, including the Bali bombings last year. This has been highlighted in specific press releases from governing bodies, like the Department of Mineral and Petroleum Resources û Western Australia, on the necessity of being in compliance with regulations for storage of explosives. As a result, audits by inspectors to assess compliance are to be expected. In a proactive move, DynoConsult has assisted several customers through benchmarking current practices, in order to identify any areas of non-compliance to the statutory requirements for explosive storage and security. This paper discusses the outcomes of supplier discussions and customer audits and highlights the implications for the industry.

Jan 1, 2003

Coal has been mined in New South Wales for nearly 200 years and prior to 1970 the vast majority of this coal was mined from underground mines using bord and pillar or similar systems.Since 1970 there have been two notable changes in coal production trends in New South Wales as can be seen from Figure 1.1. The steady growth in coal mined by open cut methods. Open cut output grew from about seven per cent of the State's output in 1970/71 to 43 per cent in 1990/91.2. The steady growth in coal mined by the longwall method. longwall output grew from negligible amounts in 1970/71 to 48 per cent of underground production in 1990/91. mines operating longwall units produced 61 per cent of underground production in 1990/91.

Jan 1, 1992

By F Grobler

Many projects fail because project performance in unfavourable economic conditions was not anticipated at the investment decision stage. This type of failure may have been avoided through the selection of a strategy that enables the project to perform well under a range of possible future economic conditions (a ærobustÆ strategy); rather than an æoptimalÆ strategy for expected future conditions that will never eventuate. This paper describes a method of rapidly generating mine plans for a number of project strategies, and then evaluating it against a representative range of equally likely economic conditions. The key performance indicators derived for each strategy are the mean value and the distribution of values (variance). A prudent investor will identify prospective strategies not only on the merit of highest mean values (as a proxy for economic reward), but also on the probability of not meeting specified investment hurdles (a proxy for risk). A robust strategy will achieve its financial objective even under adverse economic variations. This paper focuses on the effect of commodity price uncertainty; particularly around the choice of mining and processing capacity levels. Results from enumerating 2000 prices scenarios against 63 strategy combinations show how processing and mining capacity can be manipulated to manage the risk-reward trade-off.

Sep 26, 2011

The Operation of the LAROX PF-50 Pressure Filter at 'Ellatzite-Med' Flotation Plant, Bulgaria The implementation of Larox pressure belt filter, type Larox PF-50 provided within 6˜8% moisture content of the produced copper concentrate, which allowed good market realisation. The start-up of the pressure filter in 2009 reduced the electricity costs several times and had a positive impact on the technological regime of flotation. This article reveals the investigation results from the operation of the pressure filter according to different situations (density of the pulp, time for filtration, pressure of the material, pressure of the drying air, time for drying with air and other factors). The investment made in the pressure filter application is a guarantee for the successful operation of 'Ellatzite' flotation plant, Bulgaria in the coming years.

Sep 13, 2010

The authors are looking at the behaviour of the mineral processing circuits by means of the simulators operating under random disturbance. The present paper deals with the fuzzy control systems in comparison with PID controllers. A series of tests are conducted on simplified prototype processes with (1) dead time plus first-order lag model and (2) diffusive model. In the next series of tests the self-sustained process model was introduced to improve control against dead time. In both cases fuzzy and PID controllers are optimised by EVOP method. Particular attention is paid to the effect of observation noise to analyse for the problems which can be fatal to practical applications in mineral processing. Finally the methods developed are applied to a closed-circuit wet grinding system simulator operating under random disturbance.

Jan 1, 1993

By G Wood, B Lumsden

A statistical ærandomised block designÆ full plant trial of magnetic conditioning of flotation feed was undertaken at Rio TintoÆs Northparkes Mine in New South Wales. Magnetic conditioning of flotation feed has been shown to improve the flotation of 20 38 ¦m fraction for either metal. Approximately half the copper and gold losses at Northparkes are in the

Jan 1, 2007

By B E. Hall, D B. Kahler

"'Optimisation' has become a catchcry among many mining companies looking to tell the market how mining businesses will be improved and shareholder value increased. Consequently, the term 'optimisation' has been adopted by many service providers as they look to assist mining companies in achieving their objectives. But the explosion of services and products being offered with the label 'optimisation' has created some confusion. Mining companies ask for help in 'optimising' and service providers offer their assistance because they have a product that has the word 'optimisation' in its title. This is of course an over-simplification, but not by much! The authors' discussions in recent years with both mining companies and service providers have uncovered a number of very different definitions of optimisation.This paper provides a framework for identifying the scope and approach of different mining optimisation products and services, particularly the distinction between optimisation of components of the operation and the business as a whole. The different types of business optimisation are discussed, highlighting the failings of the mining industry's typical approach of strategy selection (as opposed to strategy optimisation). Mining business optimisation is discussed as a wicked problem, with the implication of this on how strategy optimisation models should be used and what the objectives of a business optimisation study should be.Case studies are also included to illustrate how fully flexible strategy optimisation models have been applied to assist decision-makers understand the impacts of changes in one part of the operation on the whole mining and treatment process, from geological models to the sale of product to customers.CITATION:Kahler, D B and Hall, B E, 2016. Strategic decision-making in mining – business optimisation using flexible evaluation models, in Proceedings Project Evaluation 2016, pp 215–225 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

The Musselwhite mine, located in northwestern Ontario, Canada, has been an underground narrow-vein gold producer since the spring of 1997. As an exploration project at the feasibility stage, much effort was undertaken to generate a geostatistical resource model that would integrate the orebodyÆs geological features, as well as the controls on mineralisation. Today as an operating mine producing over 200 000 ounces of gold per year, reconciliation studies of the tonnes and grades treated at the mill, with the feasibility model, for longer time periods, and with the grade control models, for shorter time periods, show results that are in good agreement. It was clearly demonstrated with the reconciliation to production, that the key to good reconciliation remains in the proper selection and application of the geological resource estimation method. The application of a grade interpolation technique capable of capturing threedimensionally pertinent geological features, as well as accounting for spatial grade continuity, proved to be successful in the predictability of tonnage and grade at the Musselwhite mine. Along with good mine practices, this approach, which was carried through to the operation, has produced excellent reconciliation results. The ongoing reconciliation studies at Musselwhite allow for a constant revision of the grade estimation strategy. In return, this optimisation process adds value by raising the accuracy level of production expectations. As this is an evolving practice at the mine site, further implementation developments are recommended to integrate these reconciliation procedures on a more regular basis.

Jan 1, 2002

This paper provides an overview of the future for underground thick seam coal mining in Australia. It reviews the available and anticipated mining systems and technologies which may be adopted to mine coal seams of greater than 4.5 m thickness, together with an assessment of the likely technological and operational risks and challenges involved. This overview of mining systems is presented in the context of both current and recently completed research projects funded through the Australian Coal Association Research Program (ACARP). The projects have been joint investigations between The University of New South Wales Mining Research Centre (UMRC) and the Centre for Mining Technology and Equipment (CMTE). Outcomes from the projects have included an appraisal and classification of underground thick seam reserves in Australia and their suitability for each mining method.

Jan 1, 2000