Search Documents

Dr. F. L. Stillwell. Segnit's article puts forward the views that the rocks associated with the Broken Hill lode are simply highly metamorphosed sediments, tbat metasomatism on a large scale was not an important factor at Broken Hill and that the rocks and lode were contemporaneously metamorphosed.In particular, the garnet quartzite, the most abundant rock in the limited section of the mine examined by Segnit, is described by him as a simple, metamorphosed manganiferous sediment.These views, while consonant with those of H. F. King (1958), are drastically opposed to those of myself and others e.g. Gustafson et al. (1950, p. 1383) who state that the most extensive hydrothermal alteration in the district is in and close to the zinc lodes in the Zinc Corporation and New Broken Hill Consolidated Ltd. mines. Segnit's conclusions conflict with 1. the absence of any manganiferous sediment in the Broken Hill district except in close proximity to the lode,2. the clear cut metasomatism of the dolerite dykes which indicates that the ore is younger than the dykes and therefore post-metamorphism, and 3. the petrofabric study of den Tex (1958) which provided independent evidence that the ore in its present form post-dates all events of a diastrophic nature in the area.The original sediments of the district were mudstones and calcareous sandstones with 2 to 5 per cent CaO. These have been converted by high grade metamorphism into sillimanite gneisses and quartzites characterized by the presence ...

Jan 1, 1962

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

The structural pattern of Victoria shows the presence of EW, NW, NE as well as the more readily recognised NNW factors commonly associated with the goldfields. ENE and WNW trends are also present. This structural lattice affects all rocks of the State. Landsat imagery shows that the EW, NW and NE structural elements are closely related spatially to the distribution of Palaeozoic igneous intrusives, Cainozoic volcanic vents as well as all historically important gold mines. It is suggested that the EW, NW and NE structural grid visible on landsat imagery is a reflection of the structure of a mid-crustal layer situated between 3.5 and 17 kms below the surface. The points of intersection of the structural elements of the mid-crustal layer offer most favourable loci for the escape of energy in the form of heat. The correlation between the distribution of igneous plutons, volcanic vents and centres of mineralisation, all reliant on high levels of energy for their formation, indicates the stability of the structures of the mid-crustal layer since early Palaeozoic times. The deep level crustal structures are believed to be, related to the release of stresses placed on the crust since early Palaeozoic times by the rotation of the Earth. A geological model that accommodates the presence of a mid-crustal layer as well as the complexities of the recognised orogenic cycles of southeast Australia is suggested. All 1 000 kg Au reef and deep lead mines fall within 1.5 and 2.5 km respectively of strong linears associated intimately with plutons and volcanic vents. Future exploration of the State is more likely to meet with success if it too is confined to the evaluation of these and similar linears. The mode of mineralisation of any one centre will depend upon the temperature, pressure and geochemical gradients operating on the migrating mineralising fluids as well as the structures in the host rocks. These factors are likely to have varied considerably from one centre of mineralisation to the next and consistency of mineral isation form and depth should not be expected along the length of any single Linear.

Jan 1, 1986

By G Guy, J Summerville

Over the past five years in coalmine slope evaluation the application of 3D modelling has increased significantly as software has become more user friendly but also areas requiring evaluation have become increasingly complex. Often simplistic 2D Limit Equilibrium modelling and analysis has been poorly used to solve slope stability issues by back analysis and subsequent forward predictive analysis. A plane strain condition with slope movement perpendicular to the slope strike is assumed where in reality the problem is more complex. This often leads to a misinterpretation of the failure mechanism because the failure mechanism being modelled in 2D does not generally represent the actual failure mechanism observed in the pit, with 2D modelling often oversimplifying a slope. This paper presents a case study where the initial slope assessment and remedial design evaluation was undertaken as a 2D Limit Equilibrium model which led to an overly conservative and costly remedial solution being implemented. Subsequent modelling of the slope using both 3D Limit Equilibrium and Finite Element methods were able to provide a better understanding of the structural complexities associated and correlate well with slope monitoring data to create a more realistic outcome.

Nov 29, 2022

By K D. Tuckwell

The Treasurer, the Hon Wayne Swan, has nominated ‘maximising our advantages’ from ‘Mining Boom Mark II’ as the focus of the 2011/2012 Australian Budget. Australia therefore requires a bolder and better integrated economic reform agenda if it is to convert current strong demand for mineral commodities into lasting prosperity that benefits all Australians. Lasting prosperity, well past 2012, will only be achieved if Australia can effectively reverse a decade-long deterioration in the minerals industry productivity performance due largely to capacity constraints that inhibit growth. This requires improving the efficiency of energy networks, transport infrastructure, water markets, health and education services, access to skilled people and by streamlining costly, inefficient project approvals’ processes. The common thread that holds this economic fabric together is the importance of having the right people using the most appropriate technology within the correct policy framework.In December 2010, employment in the minerals sector stood at 187 200; 21 per cent higher than one year earlier, 15 per cent higher than the industry employment peak prior to the global financial crisis in 2008 and 14 per cent greater than anticipated by industry modelling published in 2008. Managers and professionals make up approximately 15 per cent of the total workforce, yet minerals-related higher education programs (mining engineering, metallurgy and geoscience) continue to be chronically underfunded, requiring direct industry subsidies of more than $25 M over the last decade. Also, the publicly-funded Vocational Education and Training (VET) sector continues to fail the industry in the delivery of quality training programs. Importantly, the industry is a key driver of economic activity in regional and remote Australia and is the largest source of private sector employment for Indigenous Australians who comprise up to a quarter of employees in certain locations.This presentation looks at what our industry and country need to achieve to ensure we have the right people for the challenges ahead. **This is an abstract only. No paper was provided for this abstract.**

Nov 22, 2011

By J Watson, C Zhang, I Canbulat, C Wei

Coal burst is defined as a dynamic release of energy within the rock or coal mass in underground coalmines that causes violent rock or coal ejection in the vicinity of mine excavations. It poses one of the highest safety and productivity risks in the mining industry as coal bursts have the potential to cause multiple fatalities. As Australian coalmines go deeper, the likelihood of coal burst increases. Thus, it is critical to assess the ground support requirements in coal burst-prone conditions. A previous study conducted by the authors (Wei et al, 2022) reviewed the support capacities of a wide range of ground support elements in laboratory tests. This study aims to examine the role and effects of the ground support elements and systems for Australian underground coalmines to minimise the damage caused by catastrophic dynamic failures (ie coal and rock burst) and enhance the safety of mine workers.

Nov 29, 2022

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

By Neville WE, Parkinson J

One of the earliest recorded risk management schemes was implemented by the boatmen of the Yangtze river some 4,000 years ago.. Between them they arranged for shipments to be split up in such a way that a load was divided five ways: if one was lost, then 80% of the shipment got through. Bottomry contracts were in vogue in Babylonian times with similar systems being used in India, in 60OBC and 4th century Greece. One of the first accepted mutual insurance ideas came in 1835 when a mill owner in America negotiated a lower insurance premium in return for installed fire safety measures. Approximately 20 years ago risk management as a philosophy was developed in the U.S.A., the philosophy followed to England and hence to Australia about 10 years ago. The business climate which induced the philosophy of risk management was that of "tight money". The definition of "assets" was then broadened to include earning capacity, skilled personnel and in a negative sense, a corporation's liabilities. In more affluent days losses were comfortably absorbed into the ongoing business expenses, the more prudent managers took out insurance which "covered everything" at a suitable premium. Statistics are available to indicate that a high percentage, (over 60%) of businesses which suffer massive plant damage due to fire, do not restart operations, or in the event of restarting have closed operations within the next 2 to 3 years - in spite of collecting an insurance payout.

Jan 1, 1986

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

In conjunction with a study on wear of drag bits the effect of clearance angle on penetration rate was studied.Increases in clearance angle from 24 1/2 up to 30° gave an increase in penetration rate. Thereafter the rate was apparently affected by partial clogging with cuttings.Analysis of results was by a linear regression model and the t-test was applied to assess the significance of parameters in the penetration equation.

Jan 1, 1969

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE AWARD TO ELLIOTT SYLVESTER TIMOTHY O'DRISCOLLTim O'Driscoll comes from a mixture of Irish and Scottish stock. His family on the paternal side settled on land in Western Australia in the middle of the last century. His family on the maternal side were part of the W.A. goldfields scenc, including places such as Kanowna, and the Great Fingal mine, near Cue, where his grandfather lies buried.The combination of land and mining environments may perhaps have contributed to an innate interest in geology shared by Tim and his two brothers, all of whom became geologists.Tim showed an early liking for mathematical and geometric subjects, and in his B.Sc. studies at the University of Western Australia he took a major in mathematics along with geology in 1940.His first job was on the Kalgoorlie Golden Mile, and then at Norseman. After serving as a flying boat navigator in the north and south Pacific theatres in World War II he returned to Kalgoorlie and thence to Broken Hill.

Jan 1, 1977

By L Dawson, S Carr-Cornish, N Boughen, K Moffat, S Masterson

The risk and consequences of community rejection and loss of a social licence to operate is well articulated (Moffat et al 2018), however, the means for systematically managing this risk are less established. At the local scale, a mining operation is said to have a social licence to operate (SLO) when it achieves ongoing acceptance or approval from the local community and other stakeholders who can affect its profitability (Graafland, 2002). Without this social acceptance, it is very difficult for a business to operate effectively or profitably. It is well understood that social (or community) acceptance of a mine and its associated operations is a reflection of the quality of the relationship a company has with their host community (Thomson & Boutilier, 2011; Lacey & Lamont, 2014; Parsons et al., 2014; Moffat et al., 2015). Community relations are an integral part of successful mining operations and where these interactions are effective, they tend to foster mutual understanding, trust and support between a company and the host community (Kemp et al., 2006; Holley & Mitcham, 2016). Research further demonstrates that where such interactions are perceived to be procedurally fair, the increased trust created in these company-community interactions tends to lead to higher levels of acceptance of mining operations (Moffat & Zhang, 2014; Lacey et al., 2017).The challenge, however, is how to listen systematically to communities that mining and associated operations; communities that are often located across vast geographic areas and with diverse demographics. To date, traditional methods deployed to both guide and evaluate community engagement and social investment activities have been challenged to reflect the nature of the phenomenon they seek to observe, the voice of community. For example, detailed baseline surveys of community attitudes every three years by companies, as is the requirement within the policy frameworks of most large miners, provide rich insights but do not reflect the dynamic, temporal nature of the relationships that underpins their SLO. These processes typically are largely opaque to communities and distinct from the company’s engagement activities. The CSIRO Local Voices project was developed with Rio Tinto to go some way towards meeting this challenge of how to listen to the voice of community systematically. CITATION:Moffat, K, Dawson, L, Carr-Cornish, S, Boughen, N and Masterson, S, 2018. Listening to Local Voices – a systematic approach for understanding what a social licence to operate means for Rio Tinto in the Pilbara, in Proceedings Life-of-Mine 2018, pp 8–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

As the oxide reserves in an oxide/sulphide deposit are exhausted transition to the treatment of sulphides should be investigated in detail and well before processing the sulphide ore commences. The investigation should be broad based to consider all treatment options and not restricted entirely by the existing process plant treatment method. These options may include cyanidation, flotation, roasting, bacterial leaching or gravity treatment and are chosen on the basis of various testwork responses. Experiences in laboratory testing of sulphides and treatment of sulphides at various operations are discussed. This includes the treatment of copper/gold sulphides, CIP treatment of sulphides and treatment of marcasite ore in a conventional CIP circuit.

Jan 1, 1989

MR JOHN S Foxall wrote: Mr Clayton in his paper on the above subject (Proceedings, N.S. No. 34) made an assertion which should not be allowed to remain unchallenged. On the top of page 10 appears the following statement;- "By viewing the box at adepression angle of 45°, all the dimensions are disclosed and the box may be projected on isometric co-ordinates" and lower down on the same page:- "An isometric plan, being virtually a projection on a plane inclined at 45°, the nearer the dip approaches this figure so is the outline of the stoping more truly shown." Those statements embody an inaccuracy which would be misleading were an isometric plan to be constructed to suit a special case, ie the case of a mine whose lode dipped at 45°, or approximately 45° and it would be found that in such a plan the outline of the stoping would not be truly shown. The reason for this is that the depression angle at which an object is viewed in order to...

Jan 1, 1920

The design of the grinding section is discussed and details are given of the equipment installed for the autogenous grinding of ores from the C.S.A. mine at Cobar.The first section of the concentrator commenced treating ore in June, 1965 and operating experience and maintenance requirements since that time are outlined.

Jan 1, 1969

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By V N. Rudashevsky, N S. Rudashevsky

Characterisation of platinum-group element (PGE) deposits and their process products has many challenges for the process or applied mineralogist. It is now well established that the PGE distribution for such samples is variably divided between submicroscopic concentrations of PGE in sulfides, tellurides and related minerals occurring as discrete platinum-group minerals (PGM), of which there are a large number of species, many with partial replacement between the PGE and between anions. Each PGE deposit type requires a targeted approach but fundamentally, there are two general methodologies in vogue. One way is to make a large number of polished or polished thin sections for detailed scanning electron microscopy (SEM)/optical examination to determine the PGM distribution and their associations and grain sizes. The other is to make concentrates of representative crushed or processed samples, thus having fewer subsamples to examine. Our method of choice is to use hydroseparation (HS) for concentration. HS provides representative concentrates of sizes down to ~10 ¦m, not possible by other techniques. Various microbeam methods have been used for analysis of trace quantities of PGE (EPMA, micro-PIXE, SIMS and LAM-ICPMS). We prefer LAM-ICPMS (laser ablation microprobe û inductively coupled mass spectrometry) because of the relatively large analytical volume sampled, the ability to measure all the PGE, monitor up to 20 elements, together with detection levels in the tens to a few hundreds of ppb. We provide typical results derived in studies of stratiform PGE ores and tailings, and a massive Ni-Cu sulfide ore.

Jan 1, 2008

Successful management is ultimately measured by return on shareholders' funds. This is the inescapable and inexorable discipline that ultimately rules every investment. Shareholders today are predominantly, and increasingly, the superannuation funds and insurance funds of almost all of us. We have already reached the situation in Australian investment history in which the best interests of employees can be very directly identified with the best interests of the owners of the capital invested.

Jan 1, 1992

By Ryan CG, Cousens DR, Suter GF, Griffin WL

A novel method utilizing PIXE with microbeams following fire-assay has been developed to determine PGE and Au at sub-ppm levels suitable for application in exploration. Analyses of the prills from the lead and silver fire-assay yield Pt, Pd and Au concentrations readily. NiS must be used as collector if the complete suite of PGE is required, but this method is not as Convenient.

Jan 1, 1989

An on-stream iron ore analyser has been developed in collaboration with Hamersley Iron Pty. Limited for determining the iron content of both lump (- 30 + 6 mm particle size) and fines (- 6 mm particle size) on conveyor belts. The analyser, which is called IRONSCAN, is based on pair production, and is now commercially available from Mineral Con- trol Instrumentation Limited (MCI) in Adelaide. It can be mounted under existing conveyor belts with minimal modifications to the conveyor struc- ture, and the presence of steel cables in the belt does not interfere once the analyser has been correctly calibrated. The analyser has been exten- sively tested on both lump and fines on the shiploading conveyor at Damp- ier, and typically the root mean square (r.m.s.) deviation between single IRONSCAN measurements and conventional chemical analyses is better than 0.5% Fe. It is currently being evaluated on - 150 mm ore from the primary crusher at Mount Tom Price, and initial results are encourag- ing. The principal advantage of IRONSCAN is that it provides rapid infor- mation on ore grades. But perhaps its greatest potential is at the primary crusher where conventional sampling and analysis is very expensive to Implement. at the University of Melbourne, and those of us who were his students had learnt of the application of physical chemistry to pyrometallurgical processing, pioneered by Chipman in the USA, Wagner in Germany, and Richardson in the UK. It was possible, by applying this theoretical insight to the equilibria between metal, speiss or Legierung, matte and slag phases, to find a practical and effective way to recover metal values in some residues which had been accumulating for many years at the NA, but which had defied all attempts to treat them to that date. There was also an opportunity to study the batch lead refining methods still in use at all lead refineries apart from Port Pirie, and to devise optimis- ing techniques which greatly improved the operations and effected considerable savings. Next the writer spent some six years alternating between the BHAS, Port Pirie, and Imperial Smelting at Avonmouth in the UK, concerned with lead or lead-zinc smelting, and the develop- ment of several further continuous lead refining processes, before returning to Australia as Section Leader, Process Development in the CSIRO Division of Chemical Engineering, Fisherman's Bend, Victoria. Metallurgical opportunities which arose during this last period included the problem of tin smelting which had developed over about a decade: the world's tin smelters had been accustomed to treating fairly high grade tin concentrates, con- sisting of almost pure cassiterite, with very little impurity-mostly quartz, limestone, iron oxides, and sundry other silicates. Most such concentrates had been produced from alluvial deposits, where nature had already done some of difficult part of the mineral processor's work-at who knows what recovery-so that he could now produce high grade concentrates at high recovery. The smelters were not really set up for the treatment of lower grade concentrates, such as could be made with reasonably high recoveries from rock mining. Thus they imposed such penalties on impurities and lower than desired tin grades, that whenever a mineral processor improved tin recovery at the expense of lower- ing grade, such an improvement entailed a lower financial return to the miner. There was clearly a need for improved understand- ing of tin smelting, (at that time shrouded in secrecy) and develop- ment of techniques better suited to the treatment of lower grade concentrates. As well as the practical development, a start was made with the computer modelling of the smelting process, with the obiect of optimising the process parameters.

Jan 1, 1988