Search Documents

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these" materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the" dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000°C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

The earth is a planet limited in size and limited in total resources. For the forseeable future, it is the only available habitat for mankind. Therefore, it follows that the more we know about our planet the better we can utilize its space and its resources for our well-being now and in the future. But, to accomplish this, we need reliable basic information. Geosciences provide such information. Recently, Dr. M. King Hubbert took note of the important effect of the geosciences on society, on how we think, and how we live. In the first century of modern geology, 1780- 1880, the influence of geology was primarily on how we think, i.e. changing our concept of the earth from one with a short catastrophic history to one that developed gradually over enormous spans of time. In the second century, 1880-1980, the emphasis was on how we live, on expanding the knowledge base so that we could more easily find and utilize the earth's resources. Now, in the third century, i.e. from 1980 towards the year 2000 and beyond, we should concentrate on both how we think and how we live; i.e. how we can better estimate potential global' resources and how we can manage these resources for maximum benefit to mankind. Like other sciences, the geosciences build upon what has already been done. Progress is achieved by using the thoughts, measurements, and observations of past workers, adding to these the insights from new experiments and from new concepts. Geology has its own methodology and approaches; but more than most sciences, it calls also upon the tools of physics, chemistry, mathematics, engineering, and biology to help solve its problems. Today's increasing population, increasing industrialization, and increasing complexity of modern society demand more detailed geoscience information so as to better use the land, reduce geological hazards, provide an inventory of resources, facilitate waste disposal, and prepare for long-term effects such as changes in climate and sea level.

Jan 1, 1986

The thick coal seams of the South Maitland field are the only ones in New South Wales which have been worked extensively to heights beyond 3.8 m (nominal "thin" seam height). Under shallow cover only minor difficulties were experienced in developing first workings but later the widespread occurrence of incidents of spontaneous combustion and the growth of "creeps" extending over large areas gave the field its own peculiar problems. As the mines have driven under deeper cover extreme difficulties in forming development roadways have been experi- enced. Various methods have been adopted in an attempt to overcome the problems of the field.

Jan 1, 1976

By Johnston R. F

The factors which influence the reduction of chromite are investigated with special reference to Coobina chromite. This was compared with a South African chromite ore. The reduction characteristics are outlined and the reduction kinetics studied Temperature has the most significant effect, followed by particle size, silica addition and type of coal.Electron microprobe analysis of the products indicates that iron in the chromite is first reduced at temperatures above 1100°C, followed by chromium at around 1200°C. At temperatures greater than 1200°C metallic iron and chromium are formed simultaneously and subsequently give an iron-chromium-carbon alloy. It was observed that the metallic carbide contains a small amount of silicon. The decomposition of the chromite spinel was observed to pass through the FeO.Cr2O3, MgO.Cr2O3 and MgO.AI2O3 forms before slag formation. It is concluded that Coobina chromite is suitable for the production of ferrochrome if direct prereduction followed by intensive bath smelting is used.

Jan 1, 1994

By C Sylvestre

Leaders have invested heavily in traditional safety management to improve safety performance over the years. This primarily involved: • fixing the environment (eliminating the hazard) • improving the system (more/less rules, procedures etc) • making safety more conscious (more/better interactions about the importance of safety). These approaches have helped improve safety performance significantly during the last 50 years and will continue to play a role in the future. Although these approaches may be part of an overall solution, they are not enough to prevent many incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

By T E. Jeffries, M Zentilli, J STguel, C C. Wilkinson, B G. Rusk, V H. Vry

Laser ablation Inductively Coupled Plasma Mass Spectrometry (ICPMS) analysis of fluid inclusions trapping mineralising solutions in major porphyry-copper deposits indicates that copper concentrations can reach 103 - 104 ppm in both dilute, CO2-bearing fluids and in high salinity brines. Non-Cl transport of Cu is implicated. Au has been determined at 0.2 - 0.4 ppm in the low salinity fluids and may be co-transported with Cu. In contrast, high concentrations of Fe, Mn, Zn and Pb are only attained in brines and correlate strongly with Cl-indicating chloride transport. Physical and/or temporal separation of these fluid types can therefore producemetal fractionation within porphyry systems. Evidence concerning the behaviour of Mo is less clear but brine transport appears to be favoured; phase separation is one mechanism that may account for the fractionation of Mo from Cu and the formation of quartz-molybdenite veins. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D Mather

The Resources Boom of the 1960s in Australia provided a strong foundation for AustraliaÆs economic prosperity for the remainder of the twentieth century. In combination with sound economic management, our world-class minerals and energy sector has played a key role in the nationÆs competitiveness, and it has been the major source of our exports since the early 1970s. Even with the emergence since 1990 of major mineral provinces in Latin America and elsewhere, Australia has increased its percentage of world production of several minerals. Between 1990 and 2002, our share of iron ore production rose from 13 per cent to 20 per cent, nickel mine production from eight per cent to 17 per cent, copper mine production from four per cent to seven per cent and zinc mine production from 13 per cent to 17 per cent. Whether this situation will continue during the coming decades motivates the discussion of this reflective paper. The approach is to consider fundamental supply-side and demand-side issues in arriving at a view about the state of the world, the world minerals sector and the Australian resources sector in the coming decades. The argument draws from the experiences of other mature mineral producing countries such as Canada and the United States. In such nations, efficient producers have often sustained competitiveness for extended periods, despite falling grades and other challenging operating conditions. Yet several forces are changing the economic geography of the minerals industry in significant ways. These include the re-emergence of major global mining corporations, the revision of mineral policy in over 100 nations since 1985, the mobility of technology and more efficient transport both for mineral productions and mining professionals. Given these trends the paper argues that the Australian mining industry must continue to change and evolve significantly in the foreseeable future. Its leaders will need to be even more internationally focused if it is to maintain its strong competitive position.

Jan 1, 2006

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

The Tregoora Gold Project is centred around the old Mitchell River Antimony Field located 100 kilometres west-northwest of Cairns, North Queensland. The project is currently the subject of a joint venture between Strategic Minerals Corporation N.L. and Hawk Investments Limited.Historical BackgroundThe Tregoora area was first prospected for antimony and gold around 1890. During the periods 1905 to 1914 and 1937 and 1944 approximately 100 tonnes of antimony and an unknown quantity of gold were won from a number of small mines the principal one being the "Retina". A strong increase in the demand for antimony in the early 1970's resulted in renewed exploration activity in the region and the re-development of the Retina Mine. Despite the intermittent interest in the region for antimony it was not until 1984 that the potential of the area for hosting gold resources was realised with the delineation by Strategic Minerals Corporation N.L. of a significant gold deposit now referred to as the Black Knight.

Jan 1, 1986

Analysis of the topography associated with large vertical strains measured in the upper crust in the Basin and Range and elsewhere in the US Cordillera shows that it varies systematically with upper crustal strain such that it decreases where tectonism has resulted in relative thinning. The magnitude of topographic deflection suggests that the amount of thickening or thinning of the upper crust cannot also be reflected in vertical motions of the Moho discontinuity, nor can the vertical strain be isostatically accommodated by inflow or outflow of asthenosphere, mantle lithosphere or mafic lower crust. Simple isostatic calculations show that the compensating medium had a density probably within 100-200 kg/m of average upper continental crust, thus indicating that the compensating medium lies within the crust and is probably in large part quartzose. This conclusion is in accord with laboratory experiments on the strengths of rocks, and with reflection seismograms in deformed regions which suggest that the Moho is generally flat beneath regions of extreme gradients in upper crustal vertical strain. The upper crust floats on a quartzose layer in the mid-crust which, under orogenic conditions, is apparently so weak that it behaves as a relatively inviscid fluid at geologic timescales (> 10,000 a) and subcontinental lengthscales (100-1000 km).

Jan 1, 1990

Kumba Iron OreÆs Sishen Mine is one of the worldÆs largest iron ore mining operations situated in the Northern Cape, South Africa. It produces 29 million tonnes of iron ore products per annum using a dense medium separation (DMS) beneficiation process. Kumba is currently commissioning the Sishen Expansion Project (SEP) which will produce a further 13 Mtpa product through a jigging beneficiation process. The products from the Sishen Mine are highly sought after and consumed by domestic and various European and Asian customers. During beneficiation iron ore slimes are generated and discarded as waste material to the slimes dams. A study was initiated in 2005 to investigate processes to beneficiate these slimes to saleable products û prompted by the current high demand for iron ore products and the high grade in the Sishen slimes thickener underflow of approximately 54 per cent Fe. Initial laboratory scale test work indicated that a 66.5 per cent Fe iron ore concentrate could be produced from the Sishen slimes thickener underflow through a process of classification, two stage wet high intensity magnetic separation (WHIMS) and five stage flotation. This process, however, did not produce the desired results during pilot plant testing and numerous alternative process routes were investigated. The process that did achieve the desired product grade of 66.5 per cent Fe at economically feasible product yields consisted of two stage WHIMS using SLON magnetic separators. Results achieved indicate that the thickener underflow slimes can be upgraded from 54 per cent Fe to 66.5 per cent Fe at a product yield of ca. 40 per cent. Product yield could be increased through the further beneficiation of the SLON tails. The Sishen slimes thickener underflow production rate is ca. 3 Mtpa û resulting in a potential concentrate production of ca. 1.2 Mtpa. The slimes concentrate will be fed to a pelletising plant that will produce 66 per cent Fe pellets destined for domestic and or export markets.

Jan 1, 2008

By E du Plessis, J Kapusta, J L. Mauk

The world-class Bulyanhulu gold deposit (375 t Au) is in the Sukumaland greenstone belt, Northwestern Tanzania. The main mineralised quartz vein structure, termed Reef one, occurs at the contact of felsic metavolcanic rocks on the hanging wall and mafic metavolcanic rocks on the footwall. Reef one is dominated by massive quartz together with pyrite, pyrrhotite and minor chalcopyrite. Alteration in the footwall basalt is characterised by extensive chloritisation, calcification and silicification, which is strongest near the vein. Sericitisation also locally occurs adjacent to the vein. Metamorphic hornblende and plagioclase (albite) increase in abundance at a distance of 120 m from the vein and reflect the gradation into less altered rocks. The increasing abundance of chlorite, calcite, quartz and local sericite near Reef one, coupled by replacement textures suggests that most of these footwall minerals are the product of hydrothermal alteration, rather than regional metamorphism. Geochemical data shows slight enrichment in Ca, Fe and As towards the vein, whereas Zn in several drill holes becomes enriched away from Reef one. The Bulyanhulu gold deposit is a quartz-pyrite-chalcopyrite shear controlled vein with an adjacent extensive chlorite-quartz-calcite hydrothermal alteration zone (and a limited local sericite alteration zone) that passes to a hornblende-albite metamorphic assemblage further into the footwall.

Jan 1, 2002

Natural Gas has been available in New Zealand for twenty years. During that time the gas share of the energy market has grown and now natural gas forms a significant part of New Zealand's energy scene, helping consumers to achieve a higher standard of living, and reducing dependence upon imported oil.Natural gas is now used for petrochemical manufacture and power generation in addition to direct supply to consumers.As concern for the environment continues to build, natural gas will have an increasingly important role to fill in these markets. This paper sets out the background to the development of natural gas in New Zealand and identifies the current markets. It then looks at those matters which are likely to influence the role of natural gas in the 1990s.

Jan 1, 1990

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By T Mizuta, H Satoh, M Ogasawara, M Miyata, M Fukuyama

The Miocene Chichibu granitoids associated with the Chichibu skarn deposit are divided into North Body, South Body and Daikoku altered stock. Orebodies of the Chichibu skarn deposit are mainly distributed in the north-western part of the North Body and Daikoku altered stock. The North Body consists of magnetite-series granitoids ranging from tonalite to granodiorite and to monzogranite from the margins to the centre of the intrusion. The South Body consists of tonalite and granodiorite, and most of these rocks are also classified as magnetite-series granitoids. The Daikoku altered stock consists of a quartz diorite porphyry. The SiO2 contents of the granitic rocks of the North Body and South Body range from 61.6 to 70.7 wt per cent. During magmatic differentiation, Cu, As and Zn contents in fresh granitic rocks of the North Body and South Body increase with SiO2 content up to 63 wt per cent SiO2, and then progressively decrease with increasing SiO2 contents as SiO2 exceeds 65 wt per cent. Estimated pressure for the emplacement of the granitoids is about 0.5 kbars. Cathodoluminescence studies on quartz from those granitic rocks show that vapour rich two-phase fluid inclusions tend to occur in the core of quartz crystals, while halite-bearing poly-phase fluid inclusions occur in the margins of quartz crystals. The distribution of fluid inclusions suggests that fluid composition changed from low to high salinities during the growth of magmatic quartz crystals. Texture showing quartz crystals with an oval shape enclosed by radial aggregates of a mixture of fine-grained quartz, plagioclase and K-feldspar composing the groundmass of the monzogranite also suggests a pressure decrease during solidification of North Body. These findings show that high salinity fluids were present during magmatic differentiation and that Fe-Cu-Pb-Zn-Au-Ag skarn mineralisation of the Chichibu deposit was possibly associated with these high salinity fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By N F. Glenn, S Thiruchittampalam, B P. Banerjee, S Raval

The determination of shear strength parameters for the spoil material plays a crucial role in the assessment of a dump’s stability; nevertheless, their evaluation necessitates laborious laboratory experiments. In order to address this issue, Simmons and McManus (2004) formulated a framework that serves as a foundation for categorising spoils according to their distinctive shear strength parameters based on observable and tactile characteristics. This framework, previously identified as the ‘BHP Mitsubishi Alliance Coal (BMAC) Spoil Shear Strength Framework’, is now recognised as the ‘CoalSpoil’ framework. The spoil characterisation provided by the CoalSpoil framework offers benefits but is not without limitations. The examination of these attributes in the field is a time-consuming task that demands expertise. Subjectivity arises in the spoil characterisation when attributes straddle the line between two categories, such as delineating matrix-supported and framework-supported fabric structures. To enhance consistency in the spoil characterisation process, minimising human intervention is crucial to mitigate bias, classification errors, and safety risks. This study seeks to achieve this aim by introducing image-assisted and automated methods for spoil characterisation.

Sep 1, 2024

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

Modelling of Synergistic Effect of Cyanex 302 and D2EHPA in Zinc Solvent Extraction A comprehensive model is presented to predict the synergistic effect of D2EHPA and Cyanex 302 on co-extraction of zinc and manganese. The experimental results indicated that pH, temperature and the extractants ratio have strong effects on the extraction process. Correlations were proposed to predict the distribution coefficient of zinc and manganese between two phases at different conditions by multiple linear regression. The correlations were simplified by eliminating less important terms by analysis of variance. Optimum conditions (ie pH, temperature, extractants ratio and aqueous to oil phase volumetric ratio) for obtaining maximum separation of zinc from manganese at different zinc concentrations and number of extraction stages were determined. For finding the optimum condition genetic algorithm was used. Comparison the model estimations and the experimental data show that the presented model has good ability to predict the behaviours of zinc extraction system over Cyanex 302 and D2EHPA.

Sep 13, 2010

Cleaner Production stands for a proactive and preventive approach to industrial environmental management and aims for process- and/or product-integrated solutions that are both ecologically and economically efficient (æeco-efficiencyÆ). Pioneers in the field were large manufacturing and processing industries in the USA (since the late-1970s), but it took until the early-1990s before Cleaner Production was generally recognised as a valuable approach for large and medium sized enterprises. The application of Cleaner Production in mining and minerals, metals and energy production appears to lag behind other sectors, such as manufacturing and processing. This paper starts with a discussion of the Cleaner Production concept and provides examples of its application from a few selected Australian mining and minerals processing industries. This evidences that Cleaner Production can achieve significant reductions in environmental impact, in terms of reduced waste and emission generation and in terms of conservation of materials, energy and water, while simultaneously reducing operating costs. The paper then investigates a number of key issues pertaining to the implementation of Cleaner Production; ie organisation and management of Cleaner Production activities, effective tools for mastering the Cleaner Production concept as a way of life, and performance measurement.

Jan 1, 2002