Search Documents

By Denholm WT

The main objective of the experimental study was to investigate the dissolution kinetics of various forms of carbon under iron bath converting or smelting-reduction conditions, i.e., particulate, free moving carbon in contact with a turbulent iron melt. Iron/carbon melts were contained in cast magnesia-lined silicon carbide crucibles heated by a medium frequency induction furnace. The melts were stirred by injecting nitrogen through 2 mm I.D. alumina lances submerged to a depth of 50 mm in the 100 mm deep baths. Particulate carbon in the form of graphite, brown coal char and petroleum coke, were dropped directly onto the turbulent bath. The dissolution rates of the various carbon types were monitored by taking periodic bath samples for subsequent carbon analyses. The effect of carbon particle size (1-6.25 mm), the degree of bath turbulence (nitrogen stirring rates of 0-20 litres/min), and bath temperature (1300-1500¦C) were assessed. The analysis of the results was complicated by particle buoyancy effects, but it was established that the dissolution rates of the three carbon types investigated were similar, and increased linearly with increases in the gas stirring power inputs. Particle size had relatively little effect on the dissolution rates.

Jan 1, 1984

The Olympic Dam deposit is located some 600 km north of Adelaide in South Australia. It was discovered in 1975 by Western Mining Corporation and in 1979 a joint venture was formed with British Petroleum for the evaluation and development of the project. Studies were completed and construction started in 1986 with the plant being commissioned progressively between April and August of 1988. In 1993 Western Mining acquired BP's interest and are now owners of the whole deposit. The scale of the initial development was 1.5 Mtpa of ore for the production of 45 000 tpa of copper cathode, 900 tpa of uranium oxide and some gold and silver. Two expansion programs have occurred in 1992 and 1995 and current performance is at the rate of 3 Mtpa of ore for the production of 84 000 tpa of copper cathode, 1500 tpa of uranium oxide, 24 000 oz per year of confined gold and 380 000 oz per year of confined silver (Table 1). An aerial view of the plant is shown in Figure 1. The benefit of diversifying into the production of more than one product is undoubted and the flexibility of being able to produce variable quantities of copper and uranium also allows advantage to be taken of a change in market conditions.

Jan 1, 1996

Natural gas is a comparatively new fuel in Australia. It was first used in small quantities in Queensland in 1965, but it was not until 1969 that natural gas reached the capital cities Brisbane, Melbourne, and Adelaide in that order; then in 1971 it reached Perth. By the mid seventies, natural gas had secured a significant proportion of the energy markets in Queensland, Victoria, South Australia and Western Australia and in 1976 supply commenced in Sydney. In that year - 1976 - gas supplied about 12.5% of the total demand for primary energy in Australia excluding transport. In the current financial year - 1981/82 - natural gas is expected to supply nearly 19% of the market and forecasts for 1990 range up to 25%. From a starting point in the late 1960's when manufactured gas supplied a small but important proportion of the non-transport energy market - less than 3% - we have exper- ienced an average growth of nearly 24% per annum up to the present time.

Jan 1, 1982

By Smart RST C, Johnson NW, Ralston J, Griffin LF

At the Copper Concentrator of Mount Isa Mines, the largest diluent of the copper concentrate is liberated fine pyrite. Laboratory flotation tests carried out as a function of grind and flotation Eh in combination with surface analysis by X-ray photoelectron spectroscopy (XPS) have identified the major mechanisms of iron sulphide flotation. It was found that a significant proportion of the iron sulphide minerals had surface coverages of graphitic carbon, sufficient to impart moderate hydrophobicity in the absence of collector. A smaller, but economically significant proportion of chalcopyrite was also affected by the graphitic carbon coating. Two methods were tested to reduce the impact of the natural floatability of the iron sulphides on concentrate grades. 1. Depression through the use of organic depressants. 2. Preflotation to remove the "naturally hydrophobic" iron sulphides (flotation independant of Eh ) prior to chalcopyrite flotation. Preflotation was tested at the pilot plant scale. It was found that the amount of chalcopyrite reporting to the preflotation rougher concentrate could be minimised through flotation at a mildly reducing Eh by the use of nitrogen as the flotation gas to maintain the low Eh conditions resulting from grinding. The preflotation rougher concentrate was upgraded to an iron sulphide concentrate or a low grade copper concentrate.

Jan 1, 1991

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

In many metal mines in China,the 70B2 series of fans has been used for main fans for a long time.These fans generate higher static pressures than are required for the relatively high equivalent orifices of the ventilation systems of many of the mines. As a consequence, their running efficiency is common only around 30%. The loss of power is significant.

Jan 1, 1988

Computer programs for the storage, retrieval and use of basic thermodynamic and physical property data for chemical substances are described. Methods are presented for the collection, critical assessment and pre- processing of source data for files containing enthalpy, entropy and heat capacity data for 3000 compounds, enthalpy and excess entropy for 200 dilute solutions and critical propert- ies and vapour pressure for 600 compounds. Retrieval programs are discussed which allow the tabulation or plotting of many basic and derived thermodynamic properties for chemical substances or balanced reactions. Examples are given of the use of such data to infer the stability or corrosion resistance of materials and the feasibility, yield and heat release of reactions. A general purpose calculation program is discussed which allows the equilibrium compos- ition to be found for complex systems with many species and phases, using the method of Gibbs energy minimization. Methods of correction for non-ideal behaviour in these systems are discussed, as well as methods for fixing, maximizing or minimizing any desired property of the system. Examples are given of the simulation of various laboratory Experiments and industrial processes by this method.

Jan 1, 1977

Multi Torque Industries and Jadefoil have developed a safer, more efficient method of explosive protection, retention, placement, and constraint. In particular, this refers to advancements in airbag technology, where the system will offer an alternative to conventional gasbags and decking methods to provide a far more controlled and safer working environment. Airbags have provided operator control and reliability which has not until now been possible in this type of application. The benefits have been noted by current users and the advantages have provided an increase in productivity and significant savings in explosive waste. Obvious problems with gasbags lie in their instability in hot conditions where the danger is associated with gas canisters exploding with great force posing a significant risk to operators. Other problems associated with the decking systems currently on offer is the lack of versatility and operator control. The airbag systems give the operator full control to guarantee accurate placement, assured retention whilst boasting a quick operation of less than a few seconds for conventional void blocking, decking and plugging. One of the main advantages of the airbags is that the operator has full control over placement and retention force, therefore in wetter conditions where slippage can be a problem extra air can be added at the operatorÆs discretion to ensure a sufficient grip. Technical calculations coupled with experimental testing have demonstrated that an airbag will support the weight of a 30 m water column in an 89 mm hole at an initial bag pressure of 5 psig. Applications are increasingly growing whilst more customers embrace their use. Advancements such as the ability to deck in overhead holes, block voids in overhead holes at any depth, explosive retention in very wet conditions, longhole stabilisers to prevent hole closure and concertinaed liners reflect a dynamic potential for new technologies. All of these applications provide a decrease in explosive waste, an increase in operator safety, an increase in explosive protection, and an increase in productivity.

Jan 1, 2004

By T Kang, V Sahajwalla, L Lu

During devolatilisation, physical behaviour of coals was investigated in horizontal electrically heated furnace with an inert gas atmosphere, and gasification rates of four coal chars and coke were measured thermogravimetrically in a carbon dioxide atmosphere at temperatures in the range 1100oC - 1500oC. The volume change of chars was also measured in horizontal electrically heated furnace at various temperatures. Both reactivity and the activation energy for the gasification of coal chars were found to be strongly influenced by pore structure and the carbonisation conditions employed during preparation. CO2 reactivity of chars increases with increasing reaction temperature, and particularly increases more rapidly over 1300¦C. CO2 reactivity of coke is lower than that of non-coking coal chars in the range of 1100¦C to 1500¦C. CO2 reactivity of chars with smaller pore area and bigger pore diameter is less than that of chars with bigger pore area and smaller pore diameter. During gasification, the volume of chars did not change significantly at the lower temperatures of 1100¦C and 1200¦C, but at the high temperatures, 1300¦C to 1500¦C, the volume of chars quickly decreased due to ash softening and melting. The CO2 reactivities of the chars are controlled by the mixed control of chemical reaction and pore diffusion in the temperature range 1100¦C to 1300¦C, and by bulk diffusion in the temperature range 1400¦C to 1500¦C.

Jan 1, 2000

By Sen G

An amount of explosives, whether it be cylindrical, spherical, etc in configuration, with a hollow cavity in one face or end is known as a hollow or shaped charge. When this charge is initiated, a focussing of explosive energy will occur within this cavity. This focussing, or concentration of detonation products creates an intense localised force greater than just the simple detonation of a conventional explosive, (without a hollow cavity). If this hollow cavity explosive is directed against a target material this concentrated force is capable of creating a deeper penetration than the same amount of explosive without the hollow cavity. If a metallic liner material is used in the hollow cavity, upon detonation of the explosive this liner will form into a high velocity penetrating jet. Depending on the explosive type and the liner material's configuration the jet tip can travel up to 10 km/s. Linear shaped charges were developed using the abovementioned shaped charge concept but instead of being formed about an axis, they are elongated and constructed along the principal axis. Therefore instead of creating a narrow circular penetration jet, it forms a thicker planar cutting jet ideal for linear cutting purposes. Using Linear Shaped Charges (LSC) for pre-splitting is expected to result in more accurate directional fracture propagation, while minimising lateral micro fractures in the surrounding rock mass which is required to remain undamaged.

Jan 1, 1995

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

By Hosking IA, Mirkov P

Among the solutions currently being considered for improving traffic flow in Sydney are the construction of major road tunnels, principally the Eastern Distributor Tunnels, leading from the end of the Cahill Expressway to Drivers Triangle and South of Taylor Square and the Sydney Harbour Tunnel, which incorporates sections of driven tunnel at the northern and southern sides of the harbour. The Eastern Distributor Tunnels, known as Stages 2 and 3 of the Eastern Distributor Scheme comprise: Stage 2 - A south bound two lane tunnel from north of William Street to Driver's Triangle. The southern end includes two Y junctions (locally 3 to 4 lane widths) with exits into South Dowling Street, Anzac Parade and Moore Park Road. Stage 3 - A north bound, two lane tunnel from Taylor Square to Palmer Street just north of William Street. Further details of the Eastern Distributor Tunnels are given in the paper by Baxter, Chappel and Fishburn (1986) which is included in this conference.

Jan 1, 1987

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

By Canning RG, Uusna S, Goodheart BA

The paper outlines the development of"a process for removal of iron oxides from ilmenite, thereby upgrading the TiO2 content of Western Australian ilmenites, from 55 to approximately 90 per cent. In the first stage, the iron oxides are reduced with solid carbon (coal) to metallic iron. Experimental reduc- tions were carried out in crucibles,, a fluidised bed and a small pilot plant rotary kiln. The reduced'ilmenite is,then agitated in aerated water, in the presence of catalysts, so that the iron "rusts" away from the ilmenite'grains and the precipitated iron oxide is easily separable by decantation. The influence of variables on the rates. of reduction and oxidation are discussed, The oxidation rate was exam- ined for both - the' physical oxygen-transfer characteristics and electrochemically by reference to Peurbaix diagrams, which plot redox potential against solution 'PH, The upgraded ilmenite is expected to be an attractive material. for pigment -manufacture,, and the iron oxide has prospects of being a marketable by-product. The process may possibly be. applied, to .other..ores.

Jan 1, 1964

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

By Beattie T

For many years explosive sensitized explosives were assessed using the ballistic mortar. The standard test used lOg of explo- sive initiated with a detonator. Over the past 30 years many non- explosive sensitized explosives and blasting agents have been developed. Most of these new explosives and blasting agents cannot be tested in the ballistic mortar as they are not initiated by a detonator. It is also known that all explosives have a criti- cal diameter. When the cartridge diameter is less than the criti- cal diameter a stable detonation cannot be produced and the explosive fails to propagate. For many blasting agents the criti- cal diameters are greater than 50mm and such large diameters cannot be tested in the ballistic mortar. The underwater test allows explosives to be tested in diameters greater than the critical diameter and to be adequately initiated with suitable boosters. The effects of the explosive on the water are easy to measure and the test provides a safe, convenient and reproducible means of assessing explosive performance. The reaction products are allowed to expand to a low final pressure. The underwater test can therefore be used to give a measure of the total expansion work of explosives. The detonation of an explosive induces a shock wave in the surrounding water. The profile of the shock wave can be meas- ured 3-6m from the charge and the energy in the shock wave cal- culated. Measurements over a range of distances show that the shock wave is attenuated as it travels through the water and the attenuation is different for each explosive. This makes it difficult to estimate the energy dissipated in the water between the charge and a single gauge. The reaction products continue to expand and displace water. The bubble continues to expand until the kinetic energy of the water is zero. The gas pressure in the bubble is now lower than the hydrostatic pressure and the bubble radius is a maximum. The higher external hyrdostatic pressure causes the bubble to implode. The bubble energy is the work done displacing the maxi- mum bubble volume against the hydrostatic pressure and can befound from the bubble period. It is not always easy to find a large enough pond for the bubble to expand undisturbed by the water surface and the containing boundaries. This makes it difficult to determine the bubble energy accurately in shallow Ponds.

Jan 1, 1988

By G K. N Subasinghe

"In the design and operation of mineral processing plants, knowledge of the variability of ore properties and that of the expected metallurgical performance within the orebody is of great importance in order to avoid both production constraints due to inadequate design and less than expected metallurgical performance during operation. Of the many properties that determine the performance of downstream separation processes, such as flotation, gravity separation and leaching etc the liberation characteristics are of primary importance.Current methods of evaluating liberation characteristics of ores such as the use of Mineral Liberation Analyzer (MLA) and QEMSCAN techniques are expensive and suffer from the drawback that these tests are performed on comminuted particles at a given grind size and/or samples of product streams. This problem could be overcome by developing predictive models of liberation that can predict the grade distribution of comminuted products at any grind size based on texture of the parent rock. This paper discusses a procedure that has been developed to predict liberation using information obtained from a sample of the parent rock such as drill core, based on Barbery’s liberation models. The required characteristic statistical functions have been evaluated from image analysis techniques using scanning electron microscope (SEM) images of the parent rock and narrowly sized comminuted particles. Such information can then be used in a predictive model to predict or explain the variability of metallurgical performance at various grind sizes used in future operating plants. The model will predict not only the valuable mineral liberation but also gangue liberation, which will be useful to those who are looking to remove liberated gangue from comminution circuits.CITATION:Subasinghe, G K N, and Dunne, R, 2016. Predictive Model of Mineral Liberation for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 347–350 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Exploration requires substantial capital, and is an extremely risky business (only 1 in 100 prospects ever becomes a mine). The average lead time, that is the time between discovery and production, varies from around two years for a gold mine, to 15 years for a lead/zinc mine. Since it takes years to find, prove and develop most ore bodies, exploration must be carried out years ahead of the depletion of existing deposits. Investors in exploration are exposed to risk for long periods before knowing whether they will receive a return on the funds invested. The risk, high-cost, uncertainty and long lead times involved in exploration make it an aspect of commerce that most managers and investors find difficult to rationalise or understand. Nevertheless, it is a given that the long-term survival of the mining sector depends on discovery of new mineral deposits, however the immediacy of the need to find or acquire new mineral deposits in order to compete and prosper in the industry is less well understood. This paper examines the commercial realities which underlie exploration for new mineral deposits. The first and foremost reason for exploration is to maintain or increase depleting ore reserves which are the asset base of mining, but there are other compelling commercial reasons for exploring, and these are: to maintain return on investment, to achieve growth or create wealth through discoveries which lead tonew mining ventures, to remain competitive in the industry, to diversify, and to control raw material source for mineral processing and/ormarketing ventures. Exploration is necessary for survival of the industry, and also for survival of organisations competing in the industry. The organisations which discover the best orebodies are in the best position to compete, and mining organisations which fail to find or acquire new mineral deposits rapidly become uncompetitive and unable to maintain return on shareholdersÆ investment.

Jan 1, 1998