Search Documents

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975

The non-metallic minerals, excluding the construc- tions and fuel materials have for long been the "poor relations" of the Mining Industry of New South Wales. The State is self-sufficient in only a few of the industrial minerals and is almost completely lacking in any of the essential fertilizers. The deficiencies must be met by imports from overseas and interstate and in fact New South Wales imports some quantity of every one of the non-metallics. For the year 1967 the value of non-metallic mineral production amounted to only $9,390,000 or less than 3.5% of the States total of $275,900,000 for all classes of mining and quarrying. In roughly the same period, the 1967-68 financial year, New South Wales imported non- metallic materials, valued at well in excess of $22,000,000 from overseas and over $2,000,000 from interstate sources.

Jan 1, 1969

By El-Ansary M

Estimation of in-situ resources and recoverable ore reserves for the Boddington Gold Mine feasibility study was done by applying an essentially "classical" ore reserve method. This relied completely on customized graphics-based computer software requiring close co-operation and interaction between geologists and mining engineers. All geological and mining outlines were interpreted and digitized manually. Classification of selectively mineable reserves into ore, marginal and waste categories was done using a method involving convolution, devised by Dr S Carras of the Systems Research Institute of Australia, and Mr R Hooper of Kinhill Stearns. The estimation process was complicated by the frequently conflicting requirements of the various joint venture partners. The resulting ore reserve figures therefore satisfied only the most general expectations of each partner.

Jan 1, 1987

Agitation leaching data has generally not been analysed to extract the maximum amount of information that is available. Analysis of heap leaching systems has been developing over the last five years to include the underlying rate determining process. This has been found to be diffusion control for all copper leaching; irrespective of whether they are oxide or sulfide minerals. Extension of the diffusion model has enabled better scale-up protocols to be developed. Acid consumption in copper heap leaching operations has been found to be a first-order chemical controlled system. The analysis of the data is relatively straightforward. However the interpretation and scale-up is not as direct as for agitation leaching. The differences in the residence time distributions (RTDs) are required to properly account for the scale-up between test columns and field. The leaching of oxide copper in agitated systems has also been found to be diffusion controlled. However, there are significant differences in the control mechanisms. Initially the leaching control is the supply of acid to the mineral surface. This is limited by the diffusion through the surface boundary layer and is thus subject to the level of agitation. Higher agitation provides thinner boundary layers and faster diffusion rates. Similarly, higher grade material creates a thicker concentration boundary layer and relatively slower leaching. Acid consumption in agitated leach systems is also a first-order system. However, the interpretation of the RTD is easier from batch testing to continuous multiple CSTR series plant operations. Altering the method of acid delivery can significantly reduce acid consumption rates. Predilution of the acid minimises the local acid concentration near the addition point and can reduce the consumption by up to 50 per cent. Modelling of the combined leach rate(s) and acid consumption rates in agitated systems allows comparison of various leaching strategies and selection of the most appropriate. Similarly, the model allows the identification of economic limits to leach recovery; where the cost of acid consumption is greater than the value of the copper recovered. From this analysis selection of residence times for agitation leaching can be determined. The modelling tools are useful in identifying optimum conditions for the leaching process.

Jan 1, 2005

Partnering has come to prominence in the Australian construction industry in a formal sense this decade. The high level of disputation in the building and civil construction industries in the 1980s drove its development in both Australia and North America. PartneringÆs use has been most prominent in the construction industry, particularly in the civil and construction sectors of the industry. It has found favour in some mining development projects, one of the most notable being BHP MineralÆs Cannington project in NW Queensland. This paper examines the requirements of successful partnering agreements and describes in detail the mine development partnering agreement at Cannington. In particular, the paper discusses the authorÆs experience and recommendations for partnering to avoid contractual problems and achieve win û win project outcomes for all parties to major mining projects.

Jan 1, 1999

By Hall S, Upton D

WMC Resources Ltd nickel operations have expanded significantly over the last three years. Production capacity has increased at mine/concentrate, smelting and refinery processes to such an extent that WMC now ranks within the top three or four producers of nickel metal in all forms. The stainless steel industry remains the dominant user of nickel. WMC's forecast is for stainless steel production to grow at 2.8 per cent per annum off of the 1995 peak, with much slower growth in the short-term as the stainless steel inventory overhang unwinds, followed by a return to higher trend growth rates. WMC's forecast for the long-term growth in demand for primary nickel is three per cent per annum off the 1995 peak; again, slower growth in the short-term before a return to higher long-term trend rates. This projection is towards the optimistic end of the range of industry experts. It equates to a requirement for new primary nickel of 25 000 to 30 000 tonnes of annual capacity each year.

Jan 1, 1996

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

By Pollard D. M

The effects of pH, temperature and the form of zinc used on the kinetics of cementation of cadmium from process liquors were investigated. Batch tests were conducted in stirred beakers, and the cementation reaction was found to be first order controlled. The rate controlling step was thought to be the diffusion of zinc ions from the zinc surface to the bulk solution. The pH was found to have a significant effect when using Prime Western zinc or zinc dust. High reaction rates were favoured at low pH levels and a minimum rate was observed at a pH level of approximately 5 to 5.5. The pH was found to have little effect when using high grade and cathode zinc. The reaction rates increased significantly with increasing temperature; a reaction temperature of 55¦C resulted in almost complete removal of zinc from solution. Effective cementation rates were only acheived with cathode zinc after pickling in acid. The nature and specification of zinc used determined the cementation rate of cadmium, resulting in the following order: 1. Zinc dust 2. Prime Western zinc at pH 3 3. High Grade zinc at pH 3 4. Pickled cathode zinc 5. Prime Western zinc at pH 3 6. High Grade zinc at pH 3 7. Cathode zinc "as received".

Jan 1, 1989

The Middleback Ranges are a series of parallel northsouth ridges on the eastern side of the Eyre Peninsula, South Australia, about 20 miles inland from the Spencer Gulf, as shown in Fig. 1. They extend for some 20 miles across the centre of the County of York. North of them, on the same line of strike, in, the County of Manchester, is a disconnected series of lesser which ends in the Iron Monarch-Iron Knob ridge, the principal iron ore locality. These ridges are referred to in the following pages as an integral part of the Middleback Ranges.The deposits of hematite which outcrop in these ranges (Fig. 1) form the most important group of iron ore bodies in Australia, and are exploited by the Broken Hill Proprietary Company. The largest of them is the Iron Monarch (Fig. 6) .H: The next largest are the Iron Duke, the Iron Prince and Iron Baron. The Iron Knob, Iron Duchess, the North and South Iron Knights, Iron Queen, and the small body south of it, the Kimba Lease, and the deposits in the Cook's and Ash Leases, are all smaller.Numerous small lens-like bodies of hematite occur throughout the ridges, but are not of sufficient size to be of commercial use. At present only the Iron Monarch and the Iron Prince bodies are being worked. The Iron Knob was quarried previously, but its remaining supply is held in reserve.*Published by permission of the Council for Scientific and Industrial Research.

Jan 1, 1936

By J Ralston, R Sedev, D Fornasiero

The foam behaviour of low molecular weight polypropylene glycols (PPG) was investigated as a function of concentration and molecular weight (190 - 2000 g mol-1). For each polypropylene glycol, foam stability increases with concentration and passes through a maximum, beyond which foamability is suppressed as the solubility limit of the glycol is exceeded and droplets of glycol form. Light scattering data as well as static and dynamic surface tension results provide the key information leading to these interpretations. A maximum in foamability was observed for the PPG molecules with increasing molecular weight (caused by a change in molecular conformation at the interface). This suppresses the Marangoni effect and leads to a decrease in foam stability.

Jan 1, 2005

Three major and two minor uranium deposits 'have been worked by open out mining since the discovery of ,the Rum Jungle field in 1949. Total production has been about 9679000 tons of uranium ore at 7;39 lb U308/ton and 4029000 tons of copper-uranium ore at 6.27 lb U308/ton and 2.7% Cu, with significant tonnages of base'metal ores. The deposits occur in or near black pyritic slates of the Lower Proterozoic Golden Dyke Formation, near the contact with the under- lying Coomalie Dolomite. The mineralization is probably younger than the grahite complexes in the area, and a structural-stratigraphic control of ore deposition is used as a basis for uranium exploration.\

Jan 1, 1968

By Lewis PC, Carr GR, Dean JA, Glen RA

The Lachlan Fold Belt (LFB) is a complex orogenic belt which developed in Early to Mid Palaeozoic time. A number of orogenies and more localised deformational events affected the region. A simplified classification scheme for the diverse gold deposit types is proposed, subdividing primary mineralizing processes into four categories: volcanism (epithermal and volcanogenic deposits), igneous intrusion (subvolcanic/porphyry style, skarn and magmatic deposits), metahydrothermal processes (deposits generated during metamorphism and regional deformation) and hydrothermal-distal processes (deposits generated by poorly understood, generally remote large scale hydrothermal processes). Major gold deposit associations include epithermal and porphyry style deposits in Ordovician-Early Silurian shoshonitic andesite sequences; volcanogenic base metal-gold deposits in Silurian rift or basin felsic sequences; vein deposits in Late Silurian and Early Devonian S and I-type granitoids; deposits in Early Devonian sedimentary rocks of the Cobar Basin probably generated by metahydrothermal processes during basin closure and cleavage formation; deposits associated with serpentinite; and metahydrothermal quartz vein deposits in folded sedimentary rocks.Studies of host rock geochemistry suggest a relationship between magma types, gold enrichment and mineralization particularly in shoshonitic sequences and Early Devonian granitoids of the Boggy Plain Supersuite. Structural studies indicate the importance of thrust type structures and detachment faults in generation and location of gold mineralization. Lead isotope initial ratios help define metallogenic associations and a number of distinctive isotope "signatures" have been established.

Jan 1, 1990

By Mackenzie J. M W

The mechanism of clay slime flocculation in coal washing circuits is considered and it is concluded that polymer flocculants are most suitable. It was found that the addition of sea water with a polymer flocculant improved flocculation and settling, and it was also found that dilution of a flocculated pulp increased floc size and hence settling rate.In predicting plant consumption of reagent it was found that cylinder tests, or even pilot plant tests, could give erroneous results, particularly on flocculated pulps. Different flocculants may, however, be compared in cylinder tests.For filtration, flocculation with Separan plus sea water was much more beneficial than flocculation with Separan alone.INTRODUCTIONDuring the mining of coal, and its subsequent beneficiation by washing, large quantities of minus 10 mesh material are produced. This fine material, which consists of broken down shales and fine coal, causes difficulties in water clarification circuits, in refuse disposal, and in filtration of fine coal.These difficulties can be largely overcome by flocculation, and this paper discusses the mechanism of flocculation, the methods by which a selection of flocculant may be made from the large number available, and the limitation of the prediction of plant performance from laboratory tests. This work applies particularly to the washeries of The Broken Hill Proprietary Co. Ltd. (B.H.P.) and Australian Iron and Steel Ltd. (A.I. & S.) .

Jan 1, 1962

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

The Australian mining industry has suffered from a decline in its public image during the past decade. This has occurred partly as a result of increased questioning of accepted social and economic values since the mid-1960s and the greater restrictions placed on industry since then, and partly ò from the industry's inability to effectively answer its critics. Public opinion surveys have shown the depth of the decline in the industry's community acceptability and highlighted those issues which people regard as disadvantages of mining. The industry's poor public image has contributed to the difficulties of attracting young people to take up professional careers in mining. All those involved in the industry have a responsibility to assist in activities designed to improve the industry community Acceptability.

Jan 1, 1981