Search Documents

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

In submitting the accompanying sketch and description, the writer mentions that he has found this "gadget" a useful assay office adjunct.He believes that some millmen and assayers have been confronted, from time to time, with large samples of mill pulp for assay purposes and that although the commonly used method of coning and quartering dry sample is simple and effective, provided the samples are of reasonable proportion, the operator is frequently confronted with samples of pulp, sometimes up to 50 gallons. The writer stresses the advantage of being able to handle these samples. This fact inspired the design of the "gadget,"which was developed at the Kalgoorlie State Battery and has been found to give very reliable results. It has considerably eased the work of the assay office.Description. - A cone of suitable dimensions according to requirements (this one is about six gallons' capacity) is mounted on a light angle-iron frame and has a small hand-operated agitator paddle let into it far mixing purposes. The agitator and head frame are removable to facilitate cleaning. Four outlet pipes at the bottom at right angles to each other are controlled with one common plug, externally operated for discharging the pulp.Each operation of the machine delivers four equal parts; one or more of these can be used for further division as conditions require. Samples can thus be reduced to suitable assay room size in a few minutes.The dotted lines, enclosing the shaded portion, represent the four-bladed paddle.Each paddle is slotted with three parallel slots. Unshaded portions represent slots.

Jan 1, 1939

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

By Williams P. A

Tailings dams constructed by the upstream method have traditionally been built using the sand fraction of the tailings, which has automatically provided a relatively permeable embankment material, and helped provide the necessary drainage conditions which are a pre-requisite for safe and stable dam construction using this method. This paper discusses some recent trends which have resulted in proposals to use impermeable material in place of the sand fraction as the embankment material, both for the starter dam, and subsequent lifts. The consequences of these types of decisions on the overall stability of the dam are illustrated, and the need for continued monitoring of pore pressures in the tailings as the dam is raised is emphasised.

Jan 1, 1992

There are two mechanisms in the flo- tation process by which particles are transported from the pulp to the con- centrate: bubble-mineral aggregation and entrainment. It is the chemical processes which occur in the pulp which are critical to the success of flotation since they control the floatability of different min- erals and the selectivity which can be obtained. However, these chemical pro- cesses are so complex that metallurgists are still limited in their ability to predict the floatability of particles in industrial circuits by consideration of the minerals present and the chemical environment. The alternative approach to understand- ing flotation is to examine the behaviour of minerals in industrial flotation pro- cesses, to recognise similarities and differences, and to define the "laws" which appear to apply. Using this ap- proach it has been found that minerals float at a rate which is proportional to their concentration in the pulp, and that the rate of flotation of different min- erals is influenced by variables which' affect the pulp or the froth phase. The ultimate application of this approach is the use of models for circuit simulation purposes. It is this alternative approach which is the theme of this paper. One of the most important problems in understanding the technology of flotation has been in defining the characteristics of the particles being floated. Particles entering flotation vary widely in size and mineral composition, and different par- ticle types float at different rates. These rates do not change uniformly as operating variables change. It has been conventional practice to assess flotation performance in terms of the metal contents of total streams because no better method has been available, and this procedure has obscured important effects which occur in

Jan 1, 1984

By Whittaker B. N, Reddish D. J

This paper presents the physical modelling results of subsurface fracture development associated with Iongwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results haióbeen obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camels. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By J Manuel, R Muddle

The demand for iron ore has increased significantly in recent years, with new iron ore sources being mined to meet this demand. As the composition of sinter blends changes with the availability and cost of iron ore, so too does interest in the impact of new ore types on granulation and ultimately productivity. This paper describes a study into granulating characteristics of seven iron ore types, including various hematite and goethite ores. The effect of ore type on feed moisture requirements, green bed permeability, green bed strength and granule size distribution was examined for single ore blends containing coke, flux and returns. The ore size distribution was varied in these blends and its effect on granulating characteristics examined. It was found that the optimum moisture requirement of the ore was more dependent on ore type than ore size distribution, but ore size distribution (and specifically intermediate particle loading) had a greater effect on green bed permeability. The saturation moisture value for an ore was found useful in predicting both optimum granulation moisture and green bed permeability.

Jan 1, 2005

The Japanese Government promulgated the æLaw Concerning Special Measures Against DioxinsÆ on 16 July 1999 and it was enforced on 15 January 2000. This is a unique law specialised to protect the environment by the control of dioxin emissions from waste incinerators and several industrial processes. In this law, a few metallurgical processes other than waste incinerators are designated as æspecified facilitiesÆ emitting certain dioxins. Thus, emission standards for dioxins to the air were set for electric arc furnaces (EAF) for steelmaking, iron ore sintering, zinc recovery from EAF dust and aluminum recycle processes. In this paper, the inventory of dioxin emissions for Japan and the recent research and development to reduce emissions from those processes are introduced. Further, some details on the formation mechanism of dioxins and future subjects for effective control of their emissions are discussed.

Jan 1, 2002

By D Thornton

Geologists use large data sets and spend many hours and much computing time modelling the distribution of minerals throughout a rock mass. Significant investments in drilling, assaying and quality assurance and quality control (QA/QC) are made before sophisticated geostatistical techniques are applied to the collected data. A large amount of research has been done in this field such that the ore control model is a reasonably accurate reflection of the mineral that is actually in the ground. However, after all this effort, the mining engineers then work just as diligently to blast the in situ rock mass to a particle size that can be efficiently handled and further reduced by downstream comminution processes. In open cut mines, this invariably requires large amounts of explosive energy that displaces the ore boundaries from where the geologists originally defined them. Failure to accurately account for blast movement will result in misclassification, whether that is ore to waste; low grade to high grade; sulfide to oxide; or other contaminates û collectively referred to as ore loss and dilution. The financial consequence of getting this wrong is substantial and not well quantified. This diminishes all of the good geological QA/QC done in defining the ore. This paper discusses various technologies used to physically measure blast-induced orebody movement and the difficulties in modelling this with a purely theoretical approach. Rock mass structure, blast energy, design and timing contours all have significant and interrelated effects on blast movement vectors. Measured blast movement has a large variance due to the uncertainly of many of the controlling parameters û arguably dominated by the heterogeneous nature of the rock mass. Although there have been significant advances in blast movement modelling capability in recent years, this unpredictable blast movement limits their use in the context of production ore control. Certainly, without physical field measurements, accurate predictions of movement are near impossible.Limitations of traditional surface markers in determining three-dimensional (3D) blast movement within the orebody are also reviewed, and advancements in accurately measuring these vectors within blasted ore discussed

Sep 26, 2011

In line with mining operations throughout Australia, Western Mining Corporation Limiter' is striving to increase productivity by intro-ducing mechanized mining techniques wherever possible. Kambalda Nickel Operations' (K.N.O.) largest operating nickel mine, Long Shaft, is currently introducing mechanized cut and fill methods which must provide flexibility to cater for an orebody that variesconsiderably in width, both along the strike and up dip.This has resulted in modifications to the previous approach to primary level develop-ment, and intermediate stope development, and in the type of development and production equipment being employed. Electric-hydraulic diesel jumbos and diesel loaders have now been mated with conventional rail equipment and production airtrack machines are being utilized.The transition to mechanized methods is in its preliminary phase and is being monitored closely to ensure any productivity gains are not offset by a substantial drop in mine grade. The precise method ofmechanized mining has not been finalized and selective methods will be used, according to the ore width and ground conditions, which vary throughout the mine.

Jan 1, 1985

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982

By J Nantel

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

The Lennard Shelf is an Upper Devonian carbonate reef complex striking northwest for 350 km along the northeast margin of the Canning Basin. Numerous small Mississippi Valley type (MVT) Pb-Zn prospects occur within this belt, including the Wagon Pass prospect, located 105 km east of Derby in the Napier Range. At Wagon Pass, the base of the Upper Devonian sequence is a cobbly, dolomitic sandstone, the Van Emmerick Conglomerate. This is conformably overlain by the Frasnian to Famennian Pillara cycle Lower Napier Formation fore-reef deposits. These are characterized by red algal wackestones and terrigenous stylo- bedded packstones, with common dolomitization. The conformably overlying Famennian Nullara cycle contains a classic reefal assemblage, consisting of flat lying Nullara Limestone back-reef, fore-stepping massive Windjana Reef, and steep basinward dipping Upper Napier Formation marginal slope. The Nullara cycle is not dolomitized. The Wagon Pass mineralization is hosted by Lower Napier Formation dolomite. Mineral- ization consists of complex intergrowths and semi-massive assemblages of sphalerite and galena, with subordinate pyrite, marcasite, chalcopyrite, bornite, digenite, covellite and bravoite. Ore textures include granular and colloform. Gangue minerals are dolomite and very fine grained green chloritic clay. Although mineralization commonly occurs as reticulate fracture fillings, its overall distribution is stratabound. Ore paragenesis involved early "diagenetic" dolomitization, followed by breccia formation with chloritic and granular dolomite matrices. Main stage galena-sphalerite mineralization then occurred, accompanied by pervasive chloritization of silty units. Ore genesis was probably related to basin-derived "oil field" brines, with open space textures in the mineralization quite comparable to textures seen in Canning Basin dolomitic hydrocarbon reservoirs. Fluid inclusions in the host dolomite have typical MVT homogenization temperatures of 70-1150 C, and contain minor organic phases. The Van Emmerick Conglomerate, with its high porosity, dolomitization and weak Pb-Zn anomalism, was probably the aquifer for the mineralizing brines. Access of ore solutions to the Wagon

Jan 1, 1986

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

By Cox N

Fragmentation control is perhaps the most critical aspect of quarrying operations, potentially impacting on the costs of all down stream processes, and sometimes even on the economic viability of an operation. The focal points of studies to control fragmentation are generally the pattern of blastholes, the accuracy of drilling, and the most appropriate powder factor. Recent studies suggest that the performance, and consistency of performance, of explosive detonation in the blastholes may also be a significant factor impacting on blast performance in hard rock quarries. This paper presents the results of studies of bulk emulsion and watergel explosive performance, using blasthole velocity of detonation measurements, and its impact on fragmentation. Field studies show a strong correlation between blasthole VoD and blast fragmentation. Another aspect of explosive performance impacting on ease of excavation of blasted rock is muckpile displacement, from which estimates of effective heave energy have been made for different bulk slurry (emulsion and watergel) products.

Jan 1, 1995