Search Documents

By Hoberg H, Schnieder FU

The disposal of residues from coal preparation and processing will to an increasing extent require investigation and consideration of the environmental problems resulting as a consequence of this. Different authors (Diingelhoff and Plankert, 1983; Hasenpatt, 1985; Szczepanska and Twardowska, 1987) have concentrated primarily on the content and the mobilisation of inorganic contaminants such as chlorides, metals and heavy metals from spoil tips, while no publications have yet been found on the question of a possible emission of organic contaminants (PCB, PAH, HC HC) from processing residues. Here the flotation residues in particular are able to bind larger quantities of organic contaminants by physi-sorptive means because of their large specific surface and, after disposal, to be re-emitt than into the environment. The flotation agents used in coal flotation are mixtures of technical distillation products with a correspondingly fluctuating composition. As Hey, 1986 showed, they may contain, in addition to the main components (n-alkanes, alcohols, surfactants), over 50 individual trace substances. In conjunction with the structural-chemical similarity of the individual components, this complicates the quantitative analysis of individual components considerably. For the analysis of hydrocarbon content of flotation products by means of extraction with organic solvents in accordance with DIN 38408, H18, the difficulty arises, besides the insufficient sensitivity at low concentrations, that geogeonic hydrocarbons are extracted from the coal as. well and the analysis results are thus falsified. These problems were overcome by the application of the 14C radiotracer method where certain components of the flotation agents are marked with radioactive carbon (14C). By measurement of the radioactivity of solid and liquid samples, the concentration of the marked substance can be measured very sensitively and precisely, whereby the accumulative measurement of similar organic substances is ruled out. Thus the reaction path of certain substances in complex reagent mixtures such as flotation agents can be traced excellently and the conceivable environment burden resulting from flotation tailings disposal can be estimated. In this paper, the adsorption behaviour of typical components of coal flotation agents are investigated for different coals and types of gangue material, the reagent content of flotation concentrates and tailings, as well as the mobility of the reagents adsorbed onto solids. The knowledge of adsorption and desorption mechanisms of unpolar hydrocarbons emulsified in water to solids are also of particular interest for the understanding of processes of organic soil contamination and for the further development of washing processes for oil-contaminated soils.

Jan 1, 1993

Two ends of a longwall face are not only concentrated locations of equipment, but also provide ventilation and access. The roof strata stability here has an important influence on mining coal and safety. Based on field obser- vations in the gateways at Zaozhuang Colliery (Shandong Province) and model tests, the author developed a structural model of the overlying strata at the ends of the longwall face - the arc triangular cantilever plate - to which the elastic theory of plates can be applied. Factors influencing the stability of the cantilever plate and its breaking character- istics are discussed. Requirements and design parameters for supports at face ends are pro- posed, based on these factors.

Jan 1, 1986

By Tarrant GC

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

The copper deposits at Pernatty Lagoon are predominately djurleite-digenite bodies beneath the permanent water table, and chrysocolla-atacamite-malachite above the permanent water table. The minerals havebeen deposited as sheets, lobes, and pods in zones suggestive of permeability channels or permeability basius with respect to groundwater circulation.Pyrite is deposited in the form of framboids, which reflects its biogenic origin. Copper-iron sulphides deposit by replacement of pre-existent pyrite, and rarely by direct deposition. The latter mode of formation results in complex crustification bandings of chalcopyrite, bornite, sulphur rich bornites, digenite, and blue remaining covellites. The copper-iron sulphides appear to reequilibrate under constrained oxidation, resulting in an iron depletion and associated copper enrichment, the final product of which is a djurleite-digenite assemblage and associated with goethite. Where copper mineralization/ host rock relationships have rendered the rocks entirely impermeable to post ore groundwater movement, then the copper-iron sulphides are preserved as the ore assemblages.Minor and trace minerals observed include sphalerite, carrollite, galena, wittichenite, and possibly tetrahedrite in the primary ores. In the oxidized ores cllprite, tenorite, and trace brochantite have been found.

Jan 1, 1976

This paper reviews the role of fill in mining including consolidated fill both histor- ically and currently as determined by a recent survey of the Fill Subcommittee of the Canadian Advisory Committee on Rock Mechanics (CACRM). It covers the application of fill in modern min- ing methods including mechanized cut and fill, undercut and fill, post pillar cut and fill and longhole pillar recovery between stabilized fill. An automated fill preparation plant and recent developments in rotary drilling of hydraulic fill conducting holes are described briefly. The paper also summarizes the findings of some of the important laboratory and field work carried out on the behaviour of fill in Canada, the United States and Australia and again draws on current information obtained from the Fill Subcommittee of the CACRM. Space limitations and unavailability of suitable material prohi- bit the summary of similar information from other countries.

Jan 1, 1973

By Taylor R. K A, Berglin C. I K

The manganese ore deposits at Groote Eylandt are quite variable both in regard to grade and physical cond- ition. In order to treat a wider range of these ores and to increase production a new primary-crusher and' concentrator complex costing $8 million has been installed and commissioned to treat ore at the rate of 12,000 tonnes per day. The initial testwork carried out to determine the method of the ore treatment required, and on which the design of the concentrator was based, is detailed. The flowsheet and equipment used is discussed together with the operation of the plant. The production achieved and product qualities obtained are given.

Jan 1, 1973

By Tiu C, Sarmiento G, Uhlherr PHT

Fundamental rheological properties of slowly settling mineral slurries are reviewed. Slurry flow is discussed in terms of observed shear stress-shear rate behaviour. Particular emphasis is placed on establishing procedures for scale-up and design. Flow property measure- ments on red mud, a waste product from the Bayer alumina process, are presented and used to illustrate recommended design procedures.

Jan 1, 1978

The development of metallurgical training is briefly reviewed. The reasons for the current trend for Metallurgy Schools to become Schools of Materials Engineering or Materials Science are mentioned as is the role of Departments of Chemical Engineering in the teaching of extraction metallurgy. Some problems on academic staff recruit- ment are highlighted and predictions concerning future difficulties in industry getting adequately trained professional staff are made. The need for a special effort to attract and retain the best undergraduate students is put Forward.

Jan 1, 1987

With the continued drop in export coal prices (as measured in US$) delivered to the Pacific Rim market, and a fixed annual 12 per cent increase in overburden, Usibelli Coal Mine Inc was faced with the need to reduce mining costs substantially or else forfeit its foreign coal contractual commitment which amounted to about half of annual mine output. Management made a difficult and fortuitous decision to proceed with an engineered plan to switch from a two seam, extended bench dragline operation to a two seam, cast blast and spoil side operation. While down-sizing and cut-backs became the rule in all departments of the mine, the drilling and blasting budget was more than doubled. Most will agree that this is contrary to what usually happens when a mine is faced with down sizing. The more common scenario would have management target the drilling and blasting budget for decrease as a first priority to cutting cost, and then later witness a decrease in equipment performance leading to an increase in the production cost per tonne. Although Usibelli Coal Mine more than doubled its annual drilling an blasting budget three years ago, the overall stripping cost has be, reduced by more then 37 per cent.

Jan 1, 1995

In the last eight years inclined conveyor haulage systems have established themselves in the mainstream for hard rock underground mine haulage. This leaves the question; what else might be on the horizon for mine haulage and how do we address the process of selecting haulage systems for new mines? This paper considers the identification of viable haulage technologies for underground mines and explores an approach for assessing existing and potential technologies. The example of a large deep mine is considered here. The evaluation of existing haulage systems relies on precedence and the assessment of the system capacity to meet the haulage requirements envisaged for a particular mining project. The assessment of potential technologies for mine haulage relies on the capacity to deliver a viable production-scale system within the timeline envisaged for developing a mining project. The haulage technologies addressed in this paper include: shaft hoisting,conveyor haulage,truck haulage,vertical conveyors, andhydraulic hoisting. This paper does not consider rail haulage out of a mine. This is simply because Australian topography typically has insufficient relief to bring them into consideration. However, rail haulage is a widely used and effective haulage solution in situations where significant topographical relief is present. The assessment of haulage system capability focuses on the following fundamental questions: How reliable are they? What is the degree of technical risk in a business context?What levels of flexibility do they offer?How capital effective are they? What returns are indicated by the balance of capital and operating cost estimates?

Jan 1, 2008

By Scott A

The object of most blasting operations is to destroy the insitu structure of the rock mass so that mechanical equipment can efficiently excavate the rock fragments. In achieving this objective the blasting engineer is also concerned with minimising damage to the adjacent rock which forms the mine structure relied upon to provide support. Damage to this "structural" rock is undesirable but usually occurs as a result of two distinct processes: ò readjustment of stresses around the excavation as a result of the mining process itself ò impact of vibration and high pressure gases from blasting operations. Gross damage to mine structures from either cause is observed as visible alteration to the appearance of the rock structure in the form of cracking, slabbing, back or over break and visible displacement. Recent work at the Julius Kruttschnitt Mineral Research Centre (JKMRC) has shown that significant reduction in the strength of a rock mass can take place well before the onset of these obvious signs of damage. It has been demonstrated that the effect of blast damage on the behaviour of the rock mass can be many times more prominent than the effect of stress redistribution. This offers the blast design engineer the opportunity to significantly reduce blast induced damage to rock structure by modifying blasting practices. This paper introduces the current JKMRC postgraduate research projects investigating the evaluation and control of blast damage.

Jan 1, 1990

Robe River Mining manages a large open pit iron ore mine in the Pilbara region of the North-West of Australia. The mine is managed for various joint venture participants.In July 1986, Robe River Mining made various changes to its management philosophy, which were heavily publicised in the media at the time.As a result of those changes to its management philosophy, Robe River Mining has been able to dramatically increase its production output, productivity, and safety performance without having to resort to major capital outlays and without the benefit of restructuring of applicable industrial awards.

Jan 1, 1992

By G Steward

Gravity Leaching of high-grade gravity gold concentrates, such as Knelson Concentrates, with the ACACIA Reactor represents a new generation of concentrate treatment methods. The ACACIA Reactor is a complete packaged plant for the maximising of gold recoveries from gravity gold concentrates. This paper will introduce the process technology and provide process results from the Porgera ACACIA Reactor installation. The advantages of the ACACIA Reactor are many, and justification for installation has been varied. The typical advantages of the process include: increased recovery of gold from the Knelson Concentrate; no return of high-grade table tails, often grading several thousand g/t, into the mill circuit; reduction in tails grades of slow leaching gold; reduction in the requirement for operating staff by the removal of the manual tabling process and replacing with a fully automated treatment system; improved security by removing the tabling step where operating staff come into direct contact with visible gold; improved health and safety, by the removal of the treatment steps for the table concentrate, which often include operators handling corrosive chemicals and the production of sulphur and arsenic compound fumes; and improved metallurgical accounting, by allowing daily head grade calculations. The ACACIA Reactor was developed by Anglogold for Union ReefÆs Gold Plant and has been in production for over two years, and has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, there are now four full installations of the processing plant, including Anglogold Union ReefÆs, Anglogold Sunrise Dam, PACMIN Carosue Dam and Porgera Joint Venture.

Jan 1, 2002

Mining has long been an important activity for the people of Australia. The Aboriginals used rocks and minerals in their culture many thousand years before European settlement. It was not until 1840 that silver-lead ore was discovered in the Mount Lofty Ranges, and developed as Australia's first metalliferous mine.

Jan 1, 1995

The evaluation programme and procedures develop- ed for Saindak porphyry copper-gold-silver- molybdenum deposits located in an isolated area in an extremely and region of Baluchistan are described in detail. Due to its isol .ted location, far removed from supply centres, harsh climate, paucity of water and non-availability of even unskilled labour, Saindak presented problems for which no ready made solution exist- ed. It is hoped that this Paper may be of some value to those in the LDCs who may wish to undertake similar ventures.

Jan 1, 1988

Integrated chemical thermodynamic software and computerised databank systems have evolved over the last 15 years. The extent to which these systems have automated thermodynamic calculations relevant to extractive metallurgy is examined. The scope for further automation and the role of the expert consultant is discussed.

Jan 1, 1991

In July 1994 the Premier, John Fahey MP, announced that the New South Wales Government would make available a total of $40 million over six years in new funding for the Department of Mineral Resources. These funds are to be applied directly to the generation of regional geological and geophysical information. The Government's initiative known as `Discovery 2000', is aimed at providing a major boost to the exploration industry. The Government expects new discoveries to be made and new mines to be developed because of the initiative and, perhaps, the first ever commercial oil or gas production in New South Wales. The Government's return will come from increased economic activity, and from the increased royalty return from higher levels of production. Quality information is the key to successful exploration. In the highly competitive business of mineral and petroleum exploration high quality regional geological and geophysical information improve both the efficiency and effectiveness of the area selection or project generation process. Using the `needle in the hay stack' analogy, Discovery 2000 will vastly improve industry's chances of finding the haystacks. It is up to the mineral and petroleum industries to find their respective `needles'. Careful target area selection is probably the most critical factor in mineral exploration. The ability to select the most prospective areas, or to identify prospectivity that others have failed to recognise, can make all the difference between success and failure. Government geological surveys clearly have a crucial role to play in providing the geoscientific information infrastructure that companies must have if they are to make the discoveries this country needs to pay its way in the world. It is the regional information generated by Governments that sets the scene for efficient exploration. This regional information includes regional aeromagnetics and radiometrics and gravity, regional geological mapping and tectonic analysis, and geoscientific databases. The New South Wales Department of Mineral Resources (by various names) has been providing such information for over 100 years and has led the way in many aspects of the generation and dissemination of geological, geophysical and metallogenic Information.

Jan 1, 1995

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

By Denisov GA

Conventional processes for disintegration of ores are characterised by low selectivity and cause damage to the components of their structure. It affects their liberation and recovery which are connected also with the inevitable formation of extreme fines. In the world practice recently came into view 4 trend to grinding of materials within a thick layer (in a bed layer), which provides a substantial selectivity of liberation, for example, of kimberlite. The degree of diamond preservation in the final product is highly increased. However, this method causes a considerable overgrinding of material. A new method of intralayer vibro-impulse breaking of materials providing an easily adjusted force acting at the layer and timely removal of product size grains from the grinding chamber has been developed in Russia.

Jan 1, 1993

Environmental impact and rehabilitation on completion are primary considerations in obtaining approval for mine projects from government authorities.This paper focuses on the planning and commencement of rehabilitation during the mining of an open cut mine (Hedges Gold Mine) in an environmentally sensitive area in the southwest of Western Australia.

Jan 1, 1992