Search Documents

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By F. H. Samuel, H. Tahiri, S. Valtierra, H. W. Doty, A. M. Samuel

L'affinage des grains dans les alliages d'aluminium consiste à augmenter le nombre de sites de cristallisation de la phase a-Al afin d'obtenir une structure fine. Les alliages mères de type Al-Ti-B sont largement utilisés comme raffineurs des grains. Cette étude a pour but d'établir des mécanismes convenables d'affinage des grains dans l'alliage A356 en utilisant cinq alliages mères et deux températures de coulée (750°C et 950°C). Les résultats montrent que la phase a-Al prend une forme selon l'alliage mère ajoute; les échantillons coules a haute température montrent une taille de grain plus grosse; les températures de germination et de croissance augmentent avec I' augmentation du Ti ou du B et la taille des grains diminue. L'alliage mère Al-4%B montre une puissance remarquable en comparaison d'autres alliages mères. Pour cet alliage mère, le titane résiduel dans l'alliage A356 réagit avec le bore pour former TiB2 qui, par la suite, agit comme un germe actif pour la phase a-Al.

Jan 1, 2006

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By L. R. P. de Andrade Lima, D. Hodouin

The paper presents a survey of the possibilities of the simulation techniques for improving the design and operation of gold processing plants. The procedure to construct kinetic models that are used in simulators is first reviewed, and examples are given for cyanide gold dissolution and gold adsorption on carbon. Then, an overview of the structures of the plant simulators is proposed, and the simulation equations formulated for a carbon-in-leach process. Finally, the potential of simulation methods is illustrated by four examples. The first one shows how it is possible to use a simulator to design a cascade of leaching tanks while optimizing an economic performance criterion. The second one illustrates the role of simulators for optimal tuning of the cyanide addition strategy in a leaching circuit. The third example focuses on the power of simulation to design carbon transfer strategies in a carbon-in-pulp process. Finally, the last example shows the role of on-line simulators for optimally supervising the automatic control of cyanide addition into leaching tanks.

Jan 1, 2005

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu.INTRODUCTIONnickel was discovered on canada’s east coast in the vicinity of Voisey’s Bay, northern labrador, by chislett and Verbiski (Higgins, 2011) while working for Diamond Fields resources in 1993. The ovoid deposit was subsequently delineated in the winter of 1994–1995. By the end of 1995, the ovoid had been well explored, and at that time was thought to have a reserve of at least 30 million tonnes (Mt), with an average grade of 2.83% ni and 2.0% cu (naldrett, singh, Krstic, & li, 2000). Drilling to the east of the ovoid indicated the presence of significant mineralization. in June 1995, inco limited bought a 25% share in the Voisey’s Bay nickel company (VBnc), which was a subsidiary holding company set up by Diamond Fields. inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBnc for 20 years as part of this agreement. in april 1996, inco bought Diamond Fields and acquired the remaining 75% of VBnc shares."

Jan 1, 2017

By D. C. Brady

"Within six months from award of a project management contract, Les Mines Dumagami Limitée, Cadillac, Quebec, was operating its new hoisting facility. This was accomplished with less than a six-week shutdown of mine production while still maintaining shaft access for underground maintenance.The work involved installing a refurbished /3.5 ft diameter double drum hoist, replacing a timber headframe with a newsteel headframe, increasing the ore bin capacity from 500tons to 1000 tons, constructing a new substation, and upgrading related facilities.This paper describes the work and methods used by various contractors, Les Mines Dumagami Limitée and J.S. Redpath Mining Consultants Limited to bring this project to a successful completion. It discusses the history of the project from proposal stage through to the design, procurement, scheduling, and construction management. The paper also comments on problems that were encountered and the methods used to overcome them.IntroductionThe Donald J. Laronde Mine of Les Mines Dumagami Limitée (Dumagarni), a gold and copper producer, is located in northwestern Quebec, approximately half way between Val d'Or and Rouyn. The mine started production in the spring of 1988 and the first gold bar was poured in June 1988.Following a request by Dumagami, on February 22, 1989, J.S. Redpath Mining Consultants Limited(Redpath) delivered a proposal to increase hoisting capabilities from 1500 tpd to a minimum of 2500tpd. Although various concepts were considered, Redpath proposed a new hoist house along the same shaft axis as the existing hoist, and located on the site of the existing substation. They would then provide a new substation, replace the headframe with a largersteel structure , gain extra storage capacities by increasing the bin heights, and raising the roof of the bin house accordingly.Although underground mining would have to be stopped for a month, the mill production would be maintained by feed from Dumagami's open pit.Figure 1 shows the original plant layout and Figure 2 represents the general arrangement after the project was completed . Table 1 compares the original hoisting facilities to the new facilities.On March 2, Dumagami awarded Redpath a contract that included preliminary engineering, detailed engineering, procurement and contract administration, and later added construction management. The preliminary engineering refined the initialconcept, selected major equipment, and prepared schedules and capital cost estimates for the total project."

Jan 1, 1991

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By M. Greyling, C. Panaou, M. Bellino

Commonly the most frequent method of calculating the overall mass balance of a multi mineral platinum-group metal (PGM) concentrator circuit in Southern Africa has been through the use of spreadsheets, typically Microsoft EXCEL®. While there are some advantages in using spreadsheet based mass balances during the conceptual design phase of the project, their use becomes limited in the detailed design phase of the project. This paper discusses the successful application of METSIM® for mass balancing of a PGM concentrator and highlights the benefits gained during the conceptual and design phase of the project.

Jan 1, 2005

By Robert D. McKellar, Luke Frawley, Richard Okrasa

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By Robert D. McKellar, Luke Frawley, Okrasa. Richard

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By J. N. Hilton, D. Moffett, E. Barnes

"A recent pilot-plant program carried out at Rio Algom's Quirke uranium mine at Elliot Lake, Ontario is described. The goal of the research was the production of tailings basin effluents which were low in total radium-226. The process tested involved precipitation of radium with barium chloride and sedimentation in plastic-lined settling ponds. Adjustment of the tailings basin overflow from its normal value of pH 9.5 by addition of sulphuric acid to about pH 7.5 was found to give approximately a five-fold improvement in total radium-226 removal. A five-month demonstration test resulted in an effluent with a mean total radium-226 activity of44 pCi/L after 2.5 days settling time and 29 pCi/L after 5 days. The results from the demonstration program are used to propose a schedule of achievable total radium-226 activities where precipitation and sedimentation are employed. The maximum suggested values for 5 days nominal settling time are: 30 pCi/L in an annual mean, 45 pCi/L in a monthly mean. 60pCiIL in a weekly mean and 80 pCi/L in any single grab sample.IntroductionRadium-226 has been removed from effluents at the Elliot Lake uranium mines since the introduction of the first barium chloride treatment system in 1965. Current practice, which has changed little over the years, consists of radium-barium sulphate precipitation by the addition of a low do se of barium chloride to the clear overflow from the tailings basin(l·2l. Provision is made for the precipitate to settle in large natural or constructed ponds and lagoons. The residence time in these ponds, which depends on the site, ranges from 3 to 35 days, with varying degrees of efficiency being achieved."

Jan 1, 1981

By G. G. Bowser

THE time has come when, as your President, 1 turn the helm over to my worthy successor. When 1 was reminded by our Secretary that 1 had to prepare an address for this meeting, 1 was at a loss for a subject. In the hope of inspiration 1 perused the records of our Society for some years past. 1 found in these records that many problems in need of solution relative to industry in Nova Scotia were discursively dealt with and that sound thought was given to the solution of these problems, with a natural leaning, of course, to problems pertaining to the mining industry. 1 found also that some of the reasoning was remarkably prophetie. Some of these subjects and problems were: The use of pulverized coal to generate power instead of hydro-electric power; rural electrification; the importance of youth training for an efficient place in industry; the proper marketing of coal; the fuels competing with coal; the need for better in-dustrial relations between employer and employee; better education for success in the social field as applied to industry; and Canadian unity. The issue of some of these copies has been forced upon us by war. For instance, there appears to be no marketing problem for coal, nor does there ? seem to be a marketing problem for anything just at present. The problem of the coal producer just now is supply and transportation. Also, at present, coal fe.ars no competitors, such as oil-and not even hardwood. Many large companies now have an industrial Relations or Personnel Manager and department. Furthermore, we have been compelled of necessity to train our young men, and women also, for both industry and war. However, war does not solve these problems and, with the return to normal times, we may be faced with the same troubles in even greater measure. My reason for mentioning these copies is to point out that, as mining men, we are aU desirous of progress in every industry, not only the mining industry; and that mining men are able to see clearly ahead. In normal times, especially in matters not directly affecting the mining industry, we are inclined to let matters take their own good rime, or let the government do it. We do not seem to realize that these necessary and desirable changes can be made in times of peace-instead of being forced upon us by war or other social upheavals-by the method of sound thought and action to the desired end.

Jan 1, 1943

By W. C. Whittaker

"This paper gives a brief resume of the changes in the market picture for Western coal since 1948. It then analyzes present markets and recent developments in Western Canada, the western United States and Japan, and forecasts future markets in these areas to 1975.INTRODUCTIONCOAL HAS BEEN MUCH IN THE NEWS OF LATE, both in the United States and in Canada. In the United States, this is because of the booming condition of the industry and because of the purchase of control of a number of America's largest coal producers by the integrated oil and metal producing companies seeking additional fossil fuel reserves and diversification. In this regard, it is interesting to note that ownership of America's largest strip coal producer was recently acquired by one of the world's largest copper mining companies. In Canada, the conclusion of several large-scale, long-term contracts for the sale of coal to the Japan Steel Group and the projected use of Canadian coal in steel mills in the western United States has focused much attention on the coal industry."

Jan 1, 1968

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984