Search Documents

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

This growing dependence of Canada upon foreign mineral commodities, just referred to, applies particularly in the direction of the United States. There is, in fact, no more significant feature of Canada's mineral trade than the manner in which it affects the Dominion's commercial standing with that country. Our heavy adverse balance of trade with the United States is perhaps not a matter of such wide concern or frequent comment as was the case two or three years ago. It is, of course, a well-known fact that the Dominion each year buys from the States a volume of goods to a value enormously in excess of our sales to that country. And it has come to be accepted as a ?normal, though not altogether satisfactory, feature of our international commerce that a huge portion of the bill incurred by our American purchases must be met, not by our American sales, but by the proceeds of our sales to other countries, not-ably Great Britain. It is a three-cornered situation in which our trading deficit with the United States is covered largely by our trading surplus with the United Kingdom. In this situation the mineral trade plays a remarkable part. If one delves into the details of our transactions with the United States it will be found that, in one sense, the mineral trade is entirely responsible for the huge annual balance against the Dominion. In fact, Canada gets decidedly better than an even break on Canadian American trade, if one leaves out of account the three mineral groups, "iron and steel", "non- metallic minerals", and "non-ferrous metals".

Jan 1, 1924

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By J. Stiksma, J. Dennett, R. Kalanchey, J. Ji, M. Collins, T. Chan, R. Berezowsky

A pilot plant campaign has been conducted by Sherritt Technologies in support of Eldorado Gold Corporation’s evaluation of pressure oxidation technology for the treatment of refractory gold concentrates from the Certej deposit in Romania. Four separate concentrates, containing 3.5 to 5.4 g/t Au, 13.0 to 14.5% S2- and 12.0 to 32.5 g/t Ag, were tested in the eight-day campaign. The major gold-bearing mineral was pyrite. Preliminary batch tests indicated that gold extraction from the oxidized concentrates in subsequent cyanide leaching was adversely affected by the presence of organic carbon in the pressure oxidation feed when chloride in solution was at an elevated level. As such, the process conditions that were tested during the pilot plant operation were selected to either counteract the negative impact of the organic carbon, or to deactivate it during pressure oxidation. Both process routes proved feasible, yielding gold extraction of 95 to 98% in cyanide leaching of the oxidized concentrates. Silver extraction was typically in the range of 80 to 90%, provided that the oxidized concentrates were also processed in a lime boil step prior to cyanide leaching.

Jan 1, 2014

By J. P. Harrison, N. Bozorgzadeh, M. Dolowy-Busch

"It is common in rock engineering practice to characterize the triaxial strength of intact rock by using only data samples of small size. Practical guidelines such as ASTM support such sample sizes. In this paper, we investigate the reliability of the Hoek-Brown strength criterion estimated from such samples. For this purpose, we use an unusually large published set of triaxial strength data to randomly select a large number of data samples of small size to simulate the situation that frequently encounters in practice. The samples are generated with different arrangements with regards to the confining pressure. We fit the Hoek-Brown criterion to each of these samples, obtain estimates of strength parameters and compare them to those obtained from the complete data set. Our analysis suggests that estimates based on small samples are not reliable and can lead to both over- and under-estimation of strength.Additionally, we use these small samples to investigate the statistical methods for obtaining design values of strength as suggested by limit state design standards such as Eurocode 7. We show that, if used in conjunction with small samples, these methods do not guarantee a safe estimate of strength and in many cases lead to highly over-conservative estimates.We present a potential solution to this problem by augmenting the small data sets with Bayesian informative priors to give much more reliable estimates of strength. We conclude with suggestions for the development of informative prior distributions."

Jan 1, 2015

By N. Gharib, F. Hassani, P. Nekoovaght

"Novel rock breakage techniques are becoming more viable and attractive to industry. Microwave energy, as a thermal energy capable of inducing micro cracks through differential heating (therefore expansion) is a technology gaining considerable attention in mineral processing and ore comminution applications. Recently, the use of microwave radiation has been evaluated as a possible avenue for terrestrial and extra-terrestrial drilling applications as well as full face tunneling or rock breaking machines. As part of an overall research on use of microwave in rock breaking systems, the influence of microwave energy on the mechanical properties of common hard rock types as basalt has been investigated. The results revealed that microwave energy irradiation imposes micro and macro cracks to the surface of the rock being irradiated. In explosive free tunneling applications using TBM, jointed and cracked surface of rock eases the cutting process and increases penetration rate. The experimental setups have been simulated with the help of a multi-physics numerical modeling and the results have been compared with practical experiment. The wave propagation of microwave has been simulated and the distances where the power intensity is higher are identified. Experimental and simulation results underlined the potential impact of the use of microwave energy in underground or surface excavation applications such as mining and tunneling. This will also contribute economically when mine-to-mill operation is fully considered to improve the efficiency of rock crusher stages. INTRODUCTIONDuring hard rock breakage (i.e., separation of a piece of a rock from its parent deposit) in mining and civil applications, the performance of mechanical equipment such as tunnel boring machines (TBMs) is limited by high levels of bit wear and maintenance. Preweakening natural rock prior to breaking it by machine is one approach to lower bit wear and maintenance costs. Some preweakening methods apply heat directly or indirectly. For example, flame torch-assisted TBMs (Lauriello et al., 1974; Resource Technology, 1984) have been deemed economical in terms of equipment, but their feasibility is limited by high fuel consumption. Microwave energy could offer several advantages over the flame torch method: it does not produce emissions or increase fuel consumption (electricity source is available on the machine), and is easy to control (quick power on and off)."

Jan 1, 2015

By V. V. Severov, Z. Lafhaj

The flotation separation of salt type calcium minerals is problematic, due to the similarities in their formation properties and the same active Ca2+ related site for interaction with anionic collectors and similar physicochemical characteristics such as solubility, point of zero charge, surface speciation, Ca-site density. The work was performed to achieve effective and selective separation of the calcium-minerals using pure minerals samples: four calcite, two fluorite, and two apatite samples. The effect of pure and mixing anionic collectors such as oleic and linoleic acid to different ratio (2:1; 1:1; 1:2) as well as the role of nonionic collectors on the selective separation of Ca minerals were studied. All flotation tests were performed in self-aspirated flotation cell. The results obtained with the blend of anionic collectors with the molar ratio of 2:1 show a separation between apatite and calcite at pH 5 and a ratio 1:2 at pH 9. The enhancing of separation contrast using the sodium silicate as a depressant for calcite and apatite is also examined as a function of oleate/linoleate ratio. Additionally, this paper discusses the enhancing of the selective separation of Ca minerals when anionic collectors were blended with nonionic reagents. The surface reactions in aqueous mineral suspensions and the adsorption of anionic collectors blended with nonionic reagents were studied by FTIR spectroscopy. An unexpected synergistic effect was observed for some ratios between anionic and nonionic reagents. The mixture of fatty acids and nonionic reagent showed very high flotation efficiency in comparison with fatty acid alone for the flotation of an igneous low-grade phosphate ore.

Jan 1, 2016

By F. E. Goodwin

Since the last CIM Zinc and Lead Conference ten years ago, significant technical and market forces have influenced how these metals are used, and the geographic distribution of their uses. Unprecedented price fluctuations have opened competitiveness issues, while the rapid growth of the Chinese market has created challenges both inside and outside China. Recent technical developments in battery energy storage, coatings, castings and chemical applications of lead and zinc will be reviewed together with the influence of these trends on end use markets.

Jan 1, 2008

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012

By J. E. Dutrizac, Alba Sunyer

The factors affecting the precipitation of arsenic-free alunite (KAl3(SO4)2(OH)6) were investigated in a series of laboratory experiments. Although the amount of alunite precipitated increased with increasing retention time, temperature, solution pH and the concentrations of Al(SO4)1.5 or K2SO4, the composition of the products remained nearly constant. The preferred conditions identified for the precipitation of arsenic-free alunite were then used to assess the behaviour As(III) and As(V) during alunite precipitation at 98°C. Increasing additions of As(III), as NaAsO2 or As2O3, resulted in a slight increase in the amount of precipitate formed at pH 2.80. However, X-ray diffraction analysis showed all the precipitates to be alunite, and <0.2% As(III) was detected in the products. In contrast, increasing additions of As(V), as KH2AsO4 or As2O5, resulted in significant increases in the amount of precipitate formed at pH 2.80 or 3.00. Furthermore, the arsenate (AsO43-) contents of the precipitates increased up to 15%, and the sulphate contents decreased, as the As(V) concentration of the synthesis solution increased from 0 to 9 g/L. X-ray diffraction analysis of the products detected only alunite, but there was a progressive expansion of the alunite cell with increasing arsenate content. The implication is that arsenate substitutes for sulphate in the alunite structure. Preliminary observations on the environmental stability of the arsenate-bearing alunite using the TCLP protocol gave solubilities <0.4 mg/L from a precipitate containing 8.5% AsO4 and 7.8 mg/L from a product containing 19.5% AsO4. Thus, it appears that alunites containing less than -10% AsO4 would be an acceptable vehicle for the disposal of arsenic from hydrometallurgical processing solutions.

Jan 1, 2011

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD&apos;s , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By K. Adham, C. Lee

The demand for nickel is continuing to exceed inventories, and producers are working vigorously to increase capacity. Many nickel processes utilize the fluidized bed technology for its fast heat and mass transfer, excellent temperature control and low maintenance. The following four nickel applications of the fluidized bed technology have been commercialized: I) Sulfide ore roasting; II) Nickel sulfide (matte) roasting; III) Nickel oxide reduction; IV) Nickel chloride pyrohydrolysis. This paper examines the issues surrounding the application of fluidization technology to the above processes, from the stand point of the engineer modeling the process and designing the key equipment, based on the historical success stories and the fundamental principles of flow sheet synthesis. Using the available data in open literature, typical flow diagrams (with convenient bases of 1 t/h feed or product) are developed to illustrate the relative flow rates and to highlight the key features of each application. In addition, some historical background information is provided for each process with supplemental notes with regards to our company&apos;s involvements.

Jan 1, 2005

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By H. Kim

"IntroductionThe Hat Creek coal field contains low-grade coal deposits which are the thickest in the world. The diamond drilling and geophysical surveys conducted by B.C. Hydro over the last six years have indicated in excess of 2 billion tonnes of sub-bituminous to lignitic coal. The coal field is in the Interior Plateau Dry Belt, about 240 km northeast of Vancouver, and contains two explored, nearsurface coal deposits amenable to surface mining (Fig. I). The No. I deposit contains approximately 740 million tonnes of coal at 17.71 MJ / kg, or 7,600 Btu/lb, at 34.82% ash and 24% moisture. The No. 2 deposit to the south contains appreciably more coal resources at somewhat lower grade, but it has not been explored so extensively because of its higher stripping ratio. Therefore most of the exploration activities to date have been directed toward the development of the No. I deposit. The No . I coal deposit has been selected as the source of fuel for a proposed thermal powerplant to be built about 5 km east of the deposit. The purpose of this paper is to summarize the data obtained from the diamond drilling and the geophysical logging in the No. I deposit between 1974 and 1979. An attempt is made to explain the depositional environment of the Hat Creek coal measures. Because the understanding of the depositional environment in.a particular basin is essentially an evaluation of all the geologic properties of the area, the available geological information in the No. I deposit has been compiled on the basis of consistent criteria. This includes data on the lithology of the coal measures, thickness and areal distribution of the elastic sediments, and on the changes in the megascopic stratigraphic profile based on geophysical correlation. The palynopetrographic relationship and detailed sedimentological aspects are not examined in this paper. Such studies should provide important information relating the causal vegetal and chemical responses of the coals to -environmental changes. Extensive deposition of surficial materials during de-glaciation left most of the area of the Upper Hat Creek Valley devoid of bedrock exposures. Structural and stratigraphic features are hidden beneath glacial deposits and/or post-Eocene volcanics. As a result, the geological interpretation of the Hat Creek coal basin has been based primarily on drilling and geophysical data. Because of this, any explanation of the depositional environment details is tentative until the deposits are stripped for development."

Jan 1, 1985

By Zhong Zhang, Xijia Wu, Prakash C. Patnaik

"The integrated vehicle health management (IVHM) aims to provide life cycle management decisions for military platforms and their propulsion systems with reduced life cycle cost and increased operational readiness and safety. Among all the issues of IVHM, understanding the physics of failure and predicting lifetimes of the critical components are at the core: the decision makers have to know when and how components may fail in order to plan ahead. The difficulties to tackle failure problems lie in determining the material response to cyclic and dwell loading in a hot and/or corrosive environment, which all combined to induce multiple deformation and damage mechanisms, resulting in mix-mode failures. Decisions on component replacement (material substitution) and mission planning must be based on quantitative knowledge of the failure physics to mitigating the risk. This paper addresses the critical failure issues including creep, low cycle fatigue (LCF), thermomechanical fatigue (TMF); and presents a mechanism-based approach to life prediction. The mechanism-based approach, by its physics, is widely applicable over the entire operational spectrum of both structures and engines, and therefore is suitable for IVHM purposes."

Jan 1, 2015

By M. Noaparast, N. Nickoletopoulos, André R. Laplante

"This paper presents an application of the use of synthetic ores to study gold recovery by gravity. Three case studies are presented: the first focuses on the use of tungsten to study applications of Knelson Concentrators for upgrading gravity concentrates; the second on tungsten again, in this case to study the performance of a 86 Falcon Concentrator; and the third on lead to mimic gold's grinding behaviour.It is shown that the use of synthetic ores with metallic substitute for gold is not only expedient, but it can also lead to an increased understanding of separation and grinding mechanisms, because of the more accurate results and controlled particle shapes. The case studies highlight the problems associated with gold particle flakiness and gangue density. The grinding behaviour of malleable materials is shown to be complex, as particles can migrate to coarser size classes by flattening and cold welding, and to finer size classes by folding and actual breakage.IntroductionThe title of this contribution is not entirely misleading. Mineral processing has much to do with philosophy, rather Philosophy, as described by Georgius Agricola:""Furthermore, there are many arts and sciences of which the miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. ""1"

Jan 1, 1995

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986