Search Documents

"The success or failure of coal mining operations in Western Canada may hinge on the ability to extract thick coal under a variety of geological and mining circumstances and conditions. The paper presents, in who-where, what- how pattern, the current status of undergrounud mining of thick coal seams based on a review of foreign technical literature. The underground production of coal from what are considered to be thick seams is over 300 million tons per year. Methods of mining have evolved, through years of trials and tribulations, capable of meeting the requirements of a modern mine: high bulk outputs from a limited number of mining faces by concentrating in the horizontal (mechanization) and in the vertical (increased working lift)."

Jan 1, 1972

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By Ginger Gibson

As an occupational culture, mining comes with its own set of rules, agendas and values. Yet mines often also operate in the traditional territories of indigenous communities, with whom specific agreements are negotiated that commit to respect culture, economy and environment. Mines in these locations employ extremely diverse workforces whose value systems often come into conflict in on-the-job relationships. Adaptation of individual worker attitudes and industrial operating culture thus both need to occur if there is to be the negotiation of a workable relationship. This paper will discuss ways that NWT diamond mines have adapted to their workforce, to ensure that rights and cultures of their diverse workforce can be respected. Historically, the concept of culture has been dealt with solely through the forum of ?cross-cultural? workshops. Gibson presents a model of a new type of ?cultural-engagement? workshop based on the top ten cross-cultural conflicts that actually arise at a remote mine-site. This model helps managers, team leaders, and workers to tackle in-mine conflicts that arise based on differing value systems of aboriginal and non-aboriginal workers and management. In addition, Gibson suggests that the concept of culture must be more rigorously applied throughout the mine structure and not discussed only in the forum of the cross-cultural workshop.

May 1, 2007

By F. G. Boehm, T. S. Golosinski, P. M. Tucker

"In an earlier paper(1) the visits to several European mines using the bucket-wheel excavator (BWE) technology were described. It was during this trip that information was gathered on some interesting developments related to this type of mining, taking place elsewhere. It was learned that an across-the-pit system (XPS) comprised of a BWE and stacker has been operating successfully in a Hungarian mine for some time. Also the use of stackers with 225 m long booms and draglines with 125 m booms and 125m3 buckets in Soviet mines was indicated. Such equipment could be of great value to some Canadian strip mines, in particular the equipment proven useful in severe climatic conditions of U.S.S.R., similar to those of the Canadian prairies.To follow up on this information a field trip to Hungary and the U.S.S.R. was organized by the Department of Mineral Engineering, University of Alberta, to study the applications and performance of the systems in question. Visited were the Thorez mine near Visonta, Hungary, U.S.S.R. Ministry of Coal Mining and Skotchinski Institute in Moscow, Karagandashakhstoi Institute (designers of Ekibastuz mines in the Kazakh Republic) and Kostenko mine in Karaganda, Vostsibgiproshakht Institute (designers of Irsha Borodinski, Kharanovski, Moguntski and Tugnuski mines in Siberia) and the eastern Siberian Unit of the U.S.S.R. Coal Mining Ministry in Irkutsk as well as Azeiski mine located some 250 km northwest of Irkutsk. The findings of this field trip are presented."

Jan 1, 1985

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation's business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By Wm. Snow, J. R. Wallace, E. P. Duchemin

"GeneralA NOT INCONSIDERABLE proportion of the Canadian economy is dependent on the coal mining industry. This is particularly true of the eastern portion of Canada and especially so of the ( authors') province of Nova Scotia. Much has been said about the trying economic straits of the coal industry in Nova Scotia ( 1), faced, as it is, with difficult mining problems, with considerable distance from large markets, and with •competition from other (and usually foreign) fuels. It is of particular interest, at this time, therefore, to discuss one of the larger outlets for coal -that of the production of metallurgical coke.Scope of PaperWhile the title of this paper indicates that it deals with Metallurgical Coke in Canada, the authors beg leave to treat the Canadian industry very briefly and to deal specifically with coal, •coke, and smelting problems with which they are familiar, namely, the operation of the Dominion Steel and Coal Corporation in the Sydney, N.S., area. No mention is made of metallurgical coke for use in the •many foundries in Canada or in the non-ferrons metallurgical industries.Coal and Coke StatisticsA few statistics of the total output of .Canadian coal, production of metallurgical coke, and similar figures for the Dosco holdings (Sydney area only) are shown in Table I."

Jan 1, 1955

By H. R. Taylor

The history and development of this property is more or less familiar to nearly everyone connected with the mining industry, so that only a brief outline of the more important facts will be given in this article. In 1916, a small pilot mill was constructed by the British Columbia Copper Company at Copper Mountain, and during 1916 and 1917 test work was conducted to determine the possibility of concentrating the ore and also to work out a suitable flow-sheet. In the spring of 1917, the location of a mill site at Allen by, which is about 8,% miles from Copper Mountain, and near the Similkameen river, was decided on, and the designing of a 2,000-ton plant was then worked out by Bradley, Bruff and Labarthe. Early in 1918, the actual construction of the concentrator began, and, after considerable labour difficulties, it was completed in 1920. During this period of construction, the West Kootenay Power Company ran a 60,000-volt power line over from Greenwood, a distance of 102 miles, and also built a sub-station at Allenby to take care of the mine and mill. The concentrator was started up on October 20th, 1920, and ran until December 11th, 1920, a total of 18,354 tons of ore being milled. The results of this short period of operation were encouraging, but, due to tlie prevailing low price of copper and high wages, it was necessary to shut down until a more favourable time. During the latter half of 1923, some work was done on remodelling the mill. This work continued until January 8th, 1924, when it was suspended.

Jan 1, 1929

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By Dawei Yu, Kinnor Chattopadhyay

In the nickel industry, molten slags produced from a Pierce-Smith converter contain significant amounts of valuable metals in the forms of oxides and physically entrained matte droplets. A slag cleaning step, which takes places in an electrical slag-cleaning furnace, is therefore required to recover the valuable metals as a common practice. Utilization of a waste material from aluminum industry (i.e. spent potlining) as a flux to improve the slag cleaning in terms of both the metal recovery and the operation efficiency was studied by simulation with FactSage program. Results show that the addition of SPL could substantially reduce the slag viscosity due to its fluoride values, thus accelerating the settling of matte droplets. The carbon value in the SPL could also help increase the metal recovery by reducing the valuable metal oxides followed by settling.

Jan 1, 2015

By P. E. Weidmark

"PART I - Published PapersBallivy, G., and Dupuis, M., ""Laboratory testing for the design of grouted rock anchors""; Proc 6th Pan Am Conf Soil Mech Found Eng; Lima; 1:277-291; 1979.Ballivy, G., Ladanyi, B., and Gill, D., ""The effects of moisture content on the strength of fissured rocks""; Proc 1// 1ntnl Congr 1.A.E.G.; Madrid; //:2:7-16; 1978.Baumgartner, P., and Stimpson, B., ""Development of a tiltable base friction frame for kinematic studies of caving at various depths""; Int J Rock Mech Min Sci Geomech Abstr; 16:4:265-267; 1979.Bawden, W.F., and Roegiers, J.-c., ""Discussion and interpretation of the mathematics governing radial flow in a single horizontal rock fracture""; ISBN 07727-7002-6; Dept Civil Engng publication 79-11; Univ Toronto: 134p;1979.Chatterji, P.K., Smith, L.B., and Insley, A.E., ""Construction of Saline Creek Tunnel in Athabasca oil sand""; Can Geotech J; 16:1:90-107: 1979.Coates, D.F., and Gyenge, M., ""A case history of pit slope design""; Proc 4th ISRM Congr; Montreux, Switzerland; Sept 1979; 1:Theme IV:591-596; 1979.Crawford, A.M., and Curran, J.H., ""A dynamic direct shear machine for determining the time-dependent behaviour of rock joints"": Dept Civil Engng publication 79-08; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A displacement discontinuity approach to modelling the creep behavior of rock and its discontinuities""; Dept Civil Engng publication 79-09; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A higher-order displacement discontinuity element""; Dept Civil Engng publication 79-10; Univ Toronto; 1979.Cruden, D.M., ""A computer-based system for rock mass description""; Proc 1// Intnl Congr I.A.E.G.; Madrid; //:2:155-159; 1978.Cruikshank, D.J., and Curran, J.H., ""A.B.LE. approach to modelling of fluid flow in fractured rock masses""; Proc 7th Cdn Congr Appl Mech; May 1979; Sherbrooke, Que; 887-888; 1979."

Jan 1, 1980

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By F. J. Gauthier, R. G. Gray

"The possibilities of expanding the production rate from the Copper Mountain Mine have been examined using computer programs for analysing a complete range of data, beginning with the diamond drill assays and embracing all steps up to the final rates of return.Programs have been developed to calculate the mineralization inventory file, a matrix of blocks containing the grade and the type of mineralization estimated for each block. Given the topography, prices of metals and costs, the pit limits are optimized using a three-dimensional technique. Within the pit, ore reserves at any cutoff can be calculated. Mining of the pit is then simulated using an interactive production scheduling program on a timesharing computer. The annual tonnage and grade figures from the production schedule are input to a financial analysis program, where the present value and the rate of return are calculated at various metal prices. The expansion possibilities can be run through the programs with their respective costs, and evaluated using the rate of return on the marginal cash flow compared to the additional capital expenditure."

Jan 1, 1971

By L. Shang

In conventional continuous hot rolling processes, metals are usually reheated to a temperature such that the workpiece will maintain appropriate hot working characteristics as it proceeds through the rolling mill, assuming that the temperature is continually decreasing. Metallurgically, reheating will reduce micro-segregation in the as-cast material, may increase the as-cast grain size and will affect any second phase particles present in the as-cast structure. All these changes can affect the hot working characteristics, and the final as-hot rolled microstructure. In order to study the effect of reheating on AZ31 magnesium alloy, a plate sample was cast in a water cooled copper mould and a series of compression tests was performed at a temperature of 350 °C, strain rate 0.01 5-1, and strains from 0.2 to 1.0, after different reheating schedules. It was found that there is no significant difference in flow behavior between the as-cast sample and all but one of the reheated ones. The reheat treatment of the 'anomalous' sample was a two stage heat treatment; it was first reheated to 450 °C, cooled to room temperature, then reheated to 350 °C. The effect on the flow curve was to increase the flow stress. This result may be related to changes in second phase particle characteristics.

Jan 1, 2006

"11.1. IntroductionThe recovery of platinum-group elements (POE) from ores is a subject which has received almost no mention in the literature. Edwards (1975) refers to the process used for refining of the POE, throughout the Western World, as a so-called ""conventional"" process .... ""not because of the simplicity or convenience of the operations, but more probably because of the inertia of established processes and the aura of secrecy with which the major platinum refiners have surrounded this process."" There is no doubt in this writer's mind that the latter is also applicable to the dearth of knowledge of the mineralogy, geochemistry and ore deposits of PGE and that the poor recoveries, mainly attributed to the mineral beneficiation stages of concentration, are also affected by this traditional secrecy. Fortunately, this attitude is changing, due no doubt to the advantages that accrue from more open research which may be critically assessed in the literature in the traditional manner. Examples of this more open approach to recoveries and recovery problems are represented by Newman (1973), who gave some typical recovery percentages for Merensky Reef ores, and the recent encouragement and cooperation on mill samples from the Sudbury area by lnco Metals Company (cf. Cabri, 1981a).In general, platinum-group elements are recovered from an ore by the use of a physical concentration method, such as gravity separation or flotation, followed by further upgrading using further physical, wet chemical or pyrometallurgical techniques. The final process of refining in which the individual platinum-group elements are produced in pure form is outside the scope of this chapter.Platinum-group element deposits naturally fall into different categories according to the recovery process best suited for them, viz. those amenable to gravity separation, those amenable to flotation, and those where platinum-group elements are by-products of base metal sulphide, chromite and miscellaneous other deposits."

Jan 1, 1979

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations regarding the use and testing of cage safety catches, including a brief history and evolution. Regulations are similar across provinces, with only slight variations. Currently, the “Ontario-type” safety dog is the most commonly used safety catch in Canada. Performance estimation of the compensation mechanism for different safety-dog shapes and tooth angles show this shape works well and has consistent braking results, but the best efficiency is obtained for initial tooth angles greater than 10°. Miner safety is questionable for lightly loaded cages, an issue that should be addressed technically and legislatively.RÉSUMÉ Le présent article compare les diverses réglementations de sécurité minière concernant les parachutes des cages dans les provinces canadiennes ainsi que les essais qu’ils doivent subir. Il semble que les réglementations soient semblables à travers les provinces avec quelques légères différences ou divergences. Un bref historique des parachutes et de leur évolution est présenté. De nos jours, le parachute de « type Ontario » est le plus fréquemment employé à travers le Canada et il présente des résultats de freinage uniformes. Une estimation de la performance du mécanisme de compensation pour les diverses formes de taquets de sécurité et les divers angles des dents montre que cette géométrie fonctionne bien; cependant, la meilleure efficacité est obtenue pour des angles de dents supérieurs à 10°. La sécurité des mineurs est mise en jeu pour des cages faiblement chargées et ce point devrait être traité du point de vue technique et du point de vue législatif."

Jan 1, 2016