Search Documents

By William A. Napier

The Mantaro Phosphate Property is located ~ 250 km east of Lima, Peru in the Andean altiplano near the city of Huancayo, Junin District. The Mantaro deposit is a mineralized zone of phosphatic rock currently defined by surface outcrops, trenches and drilling extending over a strike length of more than 30 km and a width of more than 5 km covering ~27,700 hectares. Mineralization is exposed as three roughly parallel exposures (?mantos?) trending in a northwest-southeast direction along the Mancaspico syncline. Estimated mineral resources1 contained in Manto 1 of the Property (4% P2O5 cut-off) as of February 21, 2010, are: Measured 5.548 million tonnes @ 10.8% P2O5 Indicated 33.975 million tonnes @ 9.9% P2O5 Measured + Indicated 39.523 million tonnes @ 10.0 % P2O5 Inferred² 376.265 million tonnes @ 9.0% P2O5 1Tonnes rounded to the nearest 1,000 and grade to 1 decimal place. 2Inferred material reported with no cut-off and an assumed grade. There is considerable potential to expand the resource base. Mantos 2 and 3 of the deposit have been geologically mapped and exhibit surface mineralization widths similar to Manto 1. Given that the deposit is of marine sedimentary origin, it is reasonable to infer that comparable grades and depth of mineralization are present within Mantos 2 and 3. Based on this assumption, the potential mineral deposits within Mantos 2 and 3 are estimated to be approximately: Manto 2 425-435 million tonnes @ 9% P2O5 Manto 3 280-290 million tonnes @ 9 % P2O5 These potential quantities and grade are conceptual in nature, there has been insufficient exploration to define a mineral resource and it is uncertain if further exploration will result in these targets being delineated as a mineral resource. However, should such conceptual resources be confirmed by trenching and drilling, the Mantaro Phosphate Property would rank as one of the most significant phosphate deposits in the world.

May 1, 2011

By Dale A. Walters

The thermal recovery of bitumen reservoirs by steam assisted gravity drainage (SAGD) is often designed to maximize the operating pressure. In general, the benefits of higher operating pressures are higher steam temperatures that maximize the reduction of oil viscosity, potential permeability enhancement associated with lower effective stress and shear dilation, and a larger pressure window to allow flexible control of the producer. This is especially important for shallow reservoirs where the pressure window for injection and production is smaller. Higher operating pressure can reduce thermal efficiency (due to heat losses), but the other benefits usually compensate. The limitation of the maximum operating pressure is then based on maintaining caprock integrity. Thus, shear and tensile failure mechanisms must be quantified and managed. This paper presents a geomechanical analysis of caprock integrity for SAGD operation. Both analytical and numerical approaches are used to investigate the modes of caprock failure. Main factors in the analysis are the knowledge of the initial stress state and proper representation of the complexity of the geomaterials. Typical initial stress states for northern Alberta are presented showing the potential for low initial minimum total stress and elevated initial shear stress levels. The stress-strain behavior for the sand and caprock materials is discussed focusing on the potential for shear dilation in the sand and shear strength behavior in the caprock. Elasto-plastic constitutive models used to represent the sand and caprock are presented and compared using numerical analysis. The increase in pressure and temperature alter the stress state and disturb the soil matrix. This disturbance results in shear dilation of the sand matrix creating regions of enhanced permeability and porosity. Also, the transfer of stress and strain to the caprock causes dynamic stress changes and, therefore, dynamic behavior of shear and tensile failure conditions. Calculations are presented showing the stress paths associated with SAGD operations, suggesting better design of lab testing programs and the implications for shear dilation in the sand and shear failure in the caprock.

Jun 1, 2012

By J. Boldy

This paper is an attempt to place Canadian Precambrian volcanogenic deposits in perspective, by examining and compiling data regarding certain neglected fundamentals of size, grade, value, frequency distribution and spatial density. The discovery roles played by various exploration methods are compared and contrasted, and. using empirical methods, the probabilities of discovery are discussed, combined with the use of an effective 'cost-per-target' program. From these basic observations, realistic exploration judgments may be made. Using similar methodology, this format may be applied to other types of deposits. Precambrian volcanogenic deposits occur in a natural geometric progression in size. They number 110, of which 70% are pre-producers, producers or past-producers. These deposits are bonanzas and generally have a 'net pre-smelter' value of between $43 and $62 per ton. The statistically typical deposit is that which occupies the modal position, has 400,000 tons of ore, a value of $20 million and occurs with a frequency of 40%. A median deposit has 1.4 million tons of ore, a value of $70 million and occurs with a frequency of 15%. An upper-decile deposit ha s 13.3 million tons of ore. a value of $750 million and occurs with a frequency of 6.5%. The major, mid-upper-decile deposits have a minimum of 50 million tons of ore, a value of $3 billion and occur with a frequency of 4%. Five major volcanogenic deposits occur in the Precambrian and account for 54% of production. This contrasts with 55 deposits (all below the median) which account for 3.9% of production.

Jan 1, 1977

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By A. Golabchi

Building Information Modeling (BIM) is an increasingly popular method for generating and managing facility information during the life cycle of a building, ranging from facility conceptualization, through design, construction and its operational life. Organizations involved in Facility Management (FM) have the opportunity to use BIM as a knowledge repository to document evolving facility information and to support decisions made by the facility managers during the operational life of a facility. This paper demonstrates the potential of using BIM to develop algorithms that automate decision making for FM applications. The potential of utilizing BIM as an analysis tool is demonstrated through the scenario of HVAC (Heating, Ventilation, and Air Conditioning) system failure in an operating facility. In case of a typical HVAC malfunction today, facility occupants record complaints in a ticketing database maintained by the FM organization. Upon receiving notification of HVAC system failure, facility inspectors visit the location to confirm the reported failure. Upon confirmation, facility managers review building plans and specifications to develop a detailed plan of action to repair any HVAC components suspected of damage. Based on the plan of action, inspectors visit the facility to inspect and, in case of damage, repair the appropriate HVAC system components. These FM practices ? as currently implemented across the industry ? are labor intensive, time consuming, and often rely on unreliable and outdated information. To address these shortcomings, the authors propose an alternative methodology of HVAC fault detection in operational buildings. The authors implement an algorithm that leverages complaint ticket data and automates BIM to determine potentially damaged HVAC system components. Based on the list of HVAC components suspected of damage, the algorithm develops a plan of action for the facility inspectors. Finally, the authors discuss the advantages of the proposed method as well as the challenges of implementing automated BIM-enabled decision making processes in the FM industry.

Aug 1, 2013

By J. S. Godard

The mining developments in western Quebec have shown the ores of this district to be more complex in character than was at first expected. When the initial discoveries were made it was thought that the ores would be similar in character to those of Kirkland Lake and Porcupine areas. Developments have since shown that although the ores along the southern margin of the belt are somewhat similar, those within the belt, constituting by far the greater proportion, are vastly different, being complex mixtures of base-metal sulphides carrying values in the precious metals. These mixtures of base-metal sulphides of copper, zinc, and iron, present several problems to the metallurgist, especially in their concentration into marketable products. For the purpose .of this paper the following classification may be made of the ores of the district. Group I. - Milling Ores: (a) Ores in which~ arsenopyrite is the predominating sulphide. In this class of ore the gold occurs in fractures in the quartz and is associated to a lesser extent with the arsenopyrite and pyrite. Examples of this class of ore are the Granada, south of Pelletier lake, and the O'Brien and the Thompson in Cadillac township. (b) Ores in which iron pyrite is the predominating sulphide and gold is the valuable constituent. This may also be classed as a concentrating ore-Group III.

Jan 1, 1928

Weekly Capacity ? Current Schedule Rate (198.5 tonnes / hour) X Skip Time (112.7 hours) X Effectiveness (85%) = Weekly Capacity (19,015 tonnes) Capacity Conclusions - Existing hoists optimized are best option for Fraser Morgan (>20M + schedule for other). - Peak will have to be managed. - Critical to have equipment & infrastructure in best possible condition to ensure reliability.

Feb 1, 2008

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By H. M. Lima, L. A. Gomiero, C. A. de Morais

ABSTRACT The Caetité-Brazil uranium facility produces approximately 400 tonnes U3O8 per year from an ore averaging 0.29% U3O8. The process steps are ore crushing, heap leaching with sulphuric acid, uranium separation and purification by solvent extraction (SX) with a tertiary amine, followed by stripping with a sodium chloride solution, precipitation as ammonium diuranate (ADU), and product drying. A change in the milling process is being evaluated to increase production and uranium recovery. Heap leaching will be replaced by conventional agitated tank leaching of the –590 µm ground ore slurry in a sulphuric acid medium. Replacement of the stripping reagent is also being considered.

Jan 1, 2012

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

Superconductivity, New Mexico and Mining? ? High Temperature Superconducting cables made from ?nickel tape? ? Testing on U.S. power grid ? 25 year time horizon Purpose Create awareness about the successful application of energy management systems at a Northern Ontario mine site.

May 1, 2008

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer's programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By R. D. Prettie

Wood preservation may be defined as the art of protecting wood from decay. In its broadest sense, however, it includes a much wider field. It might be more properly de-fined as the art of protecting wood from destructive agents, such as decay, insects, marine borers, mechanical wear, etc. The earliest data on record for the preservation of organic bodies is found in Egyptian manuscripts. The bodies which we call mummies were impregnated with antiseptics, of which the principal were natrum (sodium sesqui-carbonate), sodium chloride, and sodium sulphate. After being steeped in the solution, they were subjected to either a boiling or baking process in a bituminous preparation. The first attempts in Europe to preserve timber were made by the Greeks and Romans. They extracted essential oils from the juniper and cypress trees, and either rubbed these oils into the wood they wished to preserve, or bored thousands of small holes in the wood and poured the preservative oil into the holes. The famous statues of Jupiter and Diana were carved out of wood. The ceremony of pouring in the preservative oil by the High Priests was a religious pageant of great importance, of which there are many records.

Jan 1, 1926

By G. P. van Greunen

"The rehabilitation of underground excavations has been undertaken as long as mining has existed. The conventional methods have proven to be dangerous, time consuming and expensive. During the construction of Styldrift Mine at Royal Bafokeng Platinum several vertical and horizontal excavations had to be rehabilitated. With a zero tolerance attitude towards working in unsafe conditions, together with a non-negotiable timeline to construct and ramp up the mine, the project team could not rehabilitate these excavations using conventional methods. This paper details the approach used to rehabilitate excavations using remote methods and how it was adapted to suit varying operating conditions and requirements - ensuring that no person ever entered an unsafe excavation before it was fully rehabilitated and safe. INTRODUCTION Styldrift Mine is an expansion project of the Royal Bafokeng Platinum group. It is located in South Africa in the North West Province some 10 km south of the Sun City resort (Figure 1). The mine consists of a twin shaft system (Main Shaft and Services Shaft). Capital construction of the shaft and associated infrastructure started in 2009 and is projected to be completed during 2020. The designed steady state production capacity of the shaft is 230 ktpm of Merensky ore. Production ramp-up commenced in 2017 with steady state production set to be achieved 36 months later in the fourth quarter 2020.Merensky Reef was intersected at a depth of 600 m below surface and the shaft design has a mean mining depth of 630 m. The project was approved for execution in 2008 on the basis of a suitable mine design and bankable feasibility study. One of the main excavations that required rehabilitation was an underground reef silo, Silo 4. It is a key piece of infrastructure on the critical path to allow steady state production at Styldrift Mine to be achieved. During construction excessive scaling within the silo along its 64m length necessitated urgent rehabilitation to be able to meet the ramp-up schedule. The criticality and urgency of these excavations prompted the project team to reduce the risk of failure while ensuring safe and cost-effective rehabilitation. This paper will focus on the rehabilitation of Silo 4 while capturing the essence of the learnings of all the excavations that were rehabilitated remotely."

Jan 1, 2019