Search Documents

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By M. L. Smith

"In the Phosporia formation of SE Idaho, ore quality varies by depth, seam and distance along strike; phosphorus recovery is sensitive to these variations. Plant ore feed can be blended over time to minimize this fluctuation by using a combination of mine production and inventory stockpile scheduling. Mixed-integer and goal programming has been used to optimize short-term mine production, but the seasonal nature of mine haulage requires the use of stockpiles both at the mill and the mine. The contents of the stockpiles can also be optimized as part of the production scheduling problem, but introducing inventory control introduces a nonlinear term into the formulation. A solution using a piecewise linear formulation is modelled and solved using AMPL/Cplex, and solution strategies are discussed for similar large-scale problems. IntroductionIdaho’s minable deposits of phosphate rock are found in the Meade Peak member of the Phosphoria Formation; two separate zones of this formation are mined with a combined thickness of 30 ft to 60 ft. A generalized stratigraphic section of the Phosphoria section is shown in Figure 1, illustrating the degree of complexity encountered when scheduling mine production. Alteration of the formation results in higher grade ore zones near the surface and variable in P2O5 levels between seams and along strike. This variability is seen as well in other quality characteristics critical to the production of acid and elemental phosphorus. Further, plant recovery and nodule quality are sensitive to variations in ore feed; variability in SiO2, carbonates, moisture, organics (carbon), P2O5 and other constituents of the ore can strongly affect plant recovery. Because ore quality characteristics can vary as a function of the alteration zone (or seam) being mined as well as the depth and distance along the strike of the formation, scheduling of mine production can have a highly significant effect on recovery in the plant. As illustrated in Figure 1, there are nine seams containing 20% to 35% P2O5. Phosphoric acid and elemental phosphorus production requires an ore content of 30% and 25% P2O5, respectively. Variability between numerous beds that are mined and quality variation within a seam due to alteration greatly complicates production scheduling with the result that erratic mill feed characteristics greatly decrease recovery."

Jan 1, 1999

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

A Joint Venture between Hope Bay Gold Corporation and Miramar Mining Corporation recently acquired the Hope Bay project in Nunavut, which represents the first discovery of a major new Archean greenstone gold belt in Canada since the discovery of Hemlo in 1982 and the Yellowknife belt in 1938. Located some 685 km North of Yellowknife, the Hope Bay Belt is geologically comparable to the other major gold producing regions of Canada. The initial discovery of gold mineralization in 1992 led BHP to acquire virtually all of the Hope Bay belt. Over the subsequent 6 years, BHP expended C$85 million on exploration, including 180,000 meters of drilling, 2.3km of underground workings and a 27,000 tonne bulk sample, as well as extensive environmental and economic studies. Hope Bay Gold and Miramar acquired the Hope Bay property in December 1999 for a cost of C$27 million, considerably less than the C$85 million spent by BHP in exploring the property. They both hold 50% of the project, and share expenses equally. Hope Bay Gold is the manager of all exploration phases and Miramar will manage feasibility, construction and operations. The Hope Bay Joint Venture controls 1,117 sq. km., covering virtually the entire 80 km long Hope Bay and adjacent Elu greenstone belts. We believe that Hope Bay is one of the best-undeveloped gold projects in Canada. Work to date has defined a global resource in excess of three million ounces of gold in three principal deposits, each of which is open to extension along strike and to depth. A C$17 million work program for year 2000 focused on advancing a significant portion of the gold resource to a measured and indicated category. This will provide the basis for initiation of a feasibility study in 2001. The 2000 drill program was one of the largest undertaken in Canada last year, and is a clear indication of our confidence that Hope Bay will develop into a major gold producing district. The majority of the potential mineable areas known to date lie within 350m of surface and would be accessed through a combination of open pit and declines. Currently, development of a 1,800 to 2,000 tpd gold mine producing in excess of 300,000 ounces of gold per year at cash costs below $US200 per ounce is envisioned. In addition, the exploration potential on the 80 km gold belt at Hope Bay is clearly tremendous.

May 1, 2001

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

By M. R. KEYS

"The property is about 120 miles north of Red Lake in the Favourable Lake area, district of Kenora ( Patricia part) , Ontario. The original discovery was staked by K. Murray in December, 1927. The first development work was done by the Favourable Lake Mining and Exploration Company. In 1936 Newmont Mining Corporation acquired control of the property and developed it to production by September, 1939. Production to the end of 1945 had a value of $7,534,656 from 441,457 tons of ore, an average value of $17.04 a ton . This production was mainly from gold and silver, with lead and zinc of subordinate importance.The rocks in the vicinity of the mine trend in a north-south direction. From east to west the sequence is: (1) A dark-coloured, massive rock, presumably a flow, composed mainly of quartz and biotite. ( 2) A buff- coloured, scricitized rock locally containing quartz phenocrysts and black hornblende. This is an alteration product of the dark variety and is later than the folding. It occurs mainly within the dark rock. (3) A series of sediments comprising thin beds of greywacke, grit, quartzite, conglomerate, and iron formation. ( 4) A gabbro sill, now largely altered to amphibolite.With the exception of the buff type, these rocks dip 80°E. The buff rock has a very irregular outline in comparison with the other rocks and appears to dip somewhat more flatly east. Felsite and diorite dykes are also present. These have a general strike of S.60°E. and dip 65°S .W. A post-ore diorite dyke trending N.15°E. occurs about 2,000 feet east of the mine area."

Jan 1, 1954

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By T. Lu

Microwaves have considerable potential as an energy source in both mineral processing and metals extraction. In this research, the utilization of microwave radiation for the heating of a gibbsite type bauxite ore was investigated. Firstly, thermogravimetric studies were performed in order to characterize the dewatering processes of the ore. Secondly, both the real and the imaginary permittivities, which are the fundamental properties that determine the interaction of microwaves with any given material, were measured for the bauxite ore as a function of temperature. The changes in the permittivities were shown to be related to the dewatering processes. Subsequently, the effects of operating variables such as processing time, sample mass, particle size, microwave power, sample bulk density and carbon and magnetite additions on the sample temperature in a microwave field were studied. The results showed that under suitable conditions the bauxite ore could be readily heated. Therefore, there is considerable potential for the application of microwaves for the heating of bauxite ores.

Jan 1, 2007

By K. Sun

The exothermic behavior of the intermetallic reactions inside an Al-Mn metallic powder compact and its assimilation fundamentals in molten aluminum were examined. In this study cylindrical compacts were manufactured and tested. The experimental work involved simultaneous temperature measurements of three thermocouples as well as detection of the apparent weight of the cylindrical specimen during its assimilation in liquid aluminum. The details of the intermetallic reactions prior to the compact complete disintegration were investigated by microscopically studying the morphology and local composition in a partially reacted compact. The variation of manganese concentration in the melt was determined by chemically analyzing the samples taken from the molten aluminum at specific time intervals. The exothermic reaction increases the compact's temperature above that of the liquid aluminum. In tandem with this exothermic reaction, the compact is suffering a swelling action. This swelling action disintegrates the cylindrical specimen, which is assimilated into the liquid aluminum. The intermetallic reactions proceed in a stepwise manner. Both the bath temperature and the compact composition impact on the exothermicity of the intermetallic reactions. However, when the amount of Mn in the compact is greater than 75-wt%, the maximum centerline temperature rise is slightly reduced as Mn amount increases.

Jan 1, 2004

By G. E. Joe

"This is a panel discussion on the milling experience with large volume flotation machines in Canada. Over the past ten years, the Canadian milling industry has been characterized by treatment of ever increasing tonnages of lower grade ores. In order to treat these ores efficiently, mineral processors have been employing increasingly larger volume flotation machines. In older established mills, standard flotation cells have been replaced by the larger volume models with very apparent savings in mill floor space as noted in the Opemiska copper mill.We are pleased to hear from four mill operators with extensive experience on large volume flotation machines. They are:1. I. E. Wahn, metallurgist with Falconbridge-Manibridge, who will describe their mill experiences with the Tank cell and the Maxwell cell.2. G. M. Hughes, mill superintendent of Sherritt Gordon-Ruttan, will detail recent experience with the Agitair cell.3. J. R. Maxwell, mill superintendent of Opemiska Copper, will report on their Maxwell cell installation and operation.4. A. H. Winckers, superintendent of Development and Technical Control, Sullivan Mill, will present a paper written by H. J. Chalmers describing Cominco's past experiences with large volume flotation machine installations including Denvers, Wemcos and Maxwells."

Jan 1, 1974

By W. Qin

The nucleation of d hydride in Zircaloy-4 has been studied using electron backscatter diffraction. Hydrides prefer to nucleate at intergranular rather than intragranular sites. (0001) a -Zr//(111) d -ZrHx is the most common crystallographic relationship. The hydride platelets are generally interlinked each other and form a chain-like configuration. Based on thermodynamic model, the formation mechanisms of the hydrides at different sites and the interlinked structure were analyzed. We found that the misorientation of two adjacent grains has a crucial effect on hydride nucleation sites, and the tensile stress near the tips of hydride platelets is a key factor affecting the appearance of interlinked structure.

Aug 1, 2010

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By M. K. Walter

"The underground operations of Kidd Creek Mines uses an average of 450 U.S. gpm water during regular operations, and discharges an average of 800 U.S. gpm through consecutive staged pumping lifts of 1200f t.Water is used as a flushing medium for the drilling operations and as a dust suppressant for drawpoint mucking. The water retains an average of 5% suspended solids by weight which is removed underground before being pumped to the surface. This paper outlines the treatment of the mine water for the removal of suspended solids which are chemically treated to settle out as a sludge product of 60% solids by weight. This process reduces the sludge handling operation by 50%. The sludge is systematically disposed into the ore passes.IntroductionThe Kidd Creek minesite, located 27 km north of Timmins, Ontario, produces 4.5 million tonne s of copper, lead, zinc and silver ores annually from its No. I and No.2 underground mining operations. Both mines use a sublevel blasthole stoping method of extraction.Water from the underground operation passes through a series of surface settling ponds, where it is treated to remove heavy metal ions from solution. A blend of the pond effluent with fresh water from Kidd Creek, supply the underground with water at an average rate of 450 U.S. gpm. Water flows from the production zones through coarse sumps and into a main pumping station. There are five main pumping stations underground, three in No. I Mine and two in the No.2 Mine.The No. 2 Mine pumping stations are located on the 4800 level and the 3600 level. All water below the 3600 level to the shaft bottom is controlled from the 4800 pumping station. The water from the 4800 pumping section is combined with water from the remaining levels of the No.2 Mine at the 3600 pumping station. Water from the 3600 pumping station is pumped to the 2400 pumping station in No. I Mine.The No. I Mine pumping stations are located on 2800, 2400, and 1200 levels. All water below the 2400 level to the shaft bottom is controlled through the 2800 pumping station. This water is pumped to the 2400 pumping station. The 2400 pumping station also controls the water below 1600level to 2400 level."

Jan 1, 1988

By M. Mohan Rao

A Sievert ' technique was used. The few determinations made on 10 per cent and 20 per cent V alloys did not show any deviations from Sieverts' law up to I>N2 = 1 atmosphere. The same held true for alloys of 0.2 per cent Ti. Nitrogen absorptions in Fe-Ti alloys, containing from 0.50 to 0.77 per cent Ti at 1,600°C, follow Sieverts' law at low PN2 values, but, due to the formation of a delta titanium nitride phase, deviate from this law beyond critical values of PN2? There is evidence that this phase is Ti1.1N. The behavior observed can be described by the followmg equations: Ti,.,N(o) = 1.7Ti + N K = (fT; ? % Ti)1?7 (f;;.? %~_) = 0.0020 K = fN. %~ = 0.042 '\)-:>N 2 I NTRODUCTJON Nitrogen's solubility in liquid iron-vanadium alloys was investi-gated briefly by Brick and Creevy ( 1), and more extensively by Kash-yap and Parlee (2) and by Pahlke and Elliott (7). Nitrogen's solubility in liquid iron-titanium alloys

Jan 1, 1963

By Anthony McDonald, Dominic Verhelst

"Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) started up a zinc plant and smelter in late 1930, employing technology of that period. The zinc plant has since converted from a roast/leach operation to a two stage pressure leach operation to eliminate sulphur dioxide emissioms. The smelter, however, is still continuing with much of the original roaster/reverberatory furnace technology. This paper reviews the process flow of the copper smelter, with some comments on past and recent changes.Smelter FlowsheetPrior to July 1993, the HBM&S smelter operation consisted of seven areas, namely feed preparation, roasters, reverberatory furnace, converters, anode casting, fuming plant, and dust collection. A simplified smelter flowsheet is shown in Figure 1. The data for tonnage of materials moving through the circuit are presented in Tables I to 4, and are representative of the time period from July 1992 to June 1993. A change in the zinc plant technology in 1993 resulted in the elimination of a zinc-bearing sulphide leach residue from the smelter feed blend, thereby greatly reducing the zinc content of slag produced in the smelter. Consequently the fuming plant and ancillary equipment, such as the drying plant, were shut down. These areas will, however, be described. With the closure of the zinc fuming furnaces all the slag from the reverberatory furnace is now discarded to stockpile.The over-all smelter metal recoveries are 96% for Cu and rn.5010 for Au and Ag. Figures 2 and 4 indicate historical production numbers of copper, silver and gold, respectively. A review of the minor element distribution in the smelter can be found elsewhere."

Jan 1, 1994

By Seungwoo Park, Whuisu Shim, Roe-Hoan Yoon, Kaiwu Huang

"A comprehensive froth model has been derived from first principles. It is based on predicting the kinetics of film thinning in the presence of particles of varying sizes and surface hydrophobicity. According to the Reynolds lubrication theory, the thinning of a horizontal film is driven by the excess film pressure (p), which is determined by the capillary pressure (pc) and the disjoining pressure (II). In the presence of particles, macroscopic capillary pressure (pc) is affected by the local capillary pressure (pc,local) in the vicinity of a particle and the number of particles in the film (N1,film), which in turn vary with the hydrophobicity and size of the particles. The Reynolds equation corrected for pc,local and N1,film is then used to predict the time (or froth height) at which a film is thinned to a critical rupture thickness (hcr), which in turn can be predicted using the Vrij’s capillary wave model (1966) after a modification to incorporate the contributions from hydrophobic disjoining pressure (IIhp). The model can predict bubble coarsening represented by the bubble size ratio between the top (d2,t) and bottom (d2,b) of a froth as functions of particle size and hydrophobicity, ? -potentials, frother dosages, froth height, gas flow rate, salt concentration, etc. The model predictions have been verified in experiments.INTRODUCTIONFroth flotation is regarded the best available technology today for upgrading minerals and coal fines. In the pulp phase of a flotation cell, air bubbles collect hydrophobic particles dispersed in it and rise to enter the froth phase on the top. Once in a froth phase, the bubbles coalesce with each other and become larger, resulting in a decreased bubble surface area. Under conditions of limited surface area, less hydrophobic particles drop off the bubble surface and return to the pulp phase. Thus, bubble coarsening provides a useful mechanism of increasing product grades. On the other hand, uncontrolled coarsening results in a decrease in bubble carrying capacity and hence throughput."

Jan 1, 2016

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By M. Barati

A collaborative research between University of Toronto and Hatch was conducted to understand and optimize the process conditions pertaining to a novel steelmaking technology. In this technology, known as CRISP, direct reduced iron is continuously melted and refined in a stationary electric arc furnace. The major challenge against continuous operation of the electric furnace was identified to be minimizing the corrosion of the refractory in order to achieve uninterrupted operation for a minimum of one year. Theoretical analysis and bench scale experiments together with two pilot runs resulted in defining an operating window for slag chemistry that would minimize chemical attack to the refractory while satisfying the oxidizing conditions required for sufficient decarburization. An analysis of the process in terms of energy consumption and emission of greenhouse gases revealed that it is superior to the current batch DRI-based steelmaking technologies.

Jan 1, 2011