Search Documents

By J. Ling, J. Xiao, A. R. Laplante

"The most challenging gold gravity separations occur when gangue has a high s.g., gold is fine, or a combination thereof This paper examines such separations, and evaluates the performance of a 3-in Knelson Concentrator at various rotation speeds, a 4-in SuperBowl, and a laboratory Mozley Multi-Gravity Separator (MGS). Synthetic feeds, primary cyclone underflows and flash flotation concentrates are tested.It is concluded that higher rotation speed are mostly useful for very fine (< 3 7 µm) gold recovery, with potential loss of recovery in the 37-212 µm range. This problem is traced to the collapse of the flowing film at higher Gs, which hinders the percolation of particles of intermediate size. Increasing fluidization water flow can alleviate this problem, but the recovery of very fine particle then drops. The MGS does not operate with the same principles, and can achieve good to very good recoveries of very fine to fine gold particles, but the unit has a high cost to capacity ratio, and there is no evidence yet that it can yield smeltable concentrate grade or a concentrate that can be upgraded with a shaking table.IntroductionThis presentation is a sequel to similar CMP presentations of the past eight years; all focused on practical aspects of gold recovery. The first hard rock application of the Knelson Concentrator (Laplante et al, 1990), studies of the grinding and classification behaviour of gold and other malleable metals (Banisi et al, 1991; Laplante et al, 1995), the development of a 3-in Knelson based methodology to study gold gravity circuits (Laplante and Shu, 1992), a comparison of the Knelson and Falcon (Laplante, Laplante et al, 1993), the presentation of a test to determine the amount of gravity recoverable gold, or GRG (Laplante et al, 1996), and the use of synthetic materials, in particular tungsten, to mimic gold (Laplante et al, 1995) were presented. A summary of many practical implication of the McGill research was presented in 1994 (Laplante). Whereas gold gravity recovery was less popular and largely jig-based (in North America) at the beginning of the eighties, many gold plants now incorporate a gravity circuit, and the Knelson Concentrator is the most commonly used unit."

Jan 1, 1998

By Piotr Litwa

The paper focuses on actions aiming at improvement of work safety in mines, particularly in those extracting hard coal, taking into account the characteristics of natural hazards in Polish underground mining and the reasons of mining disasters connected with those hazards. It refers to conclusions addressed to scientific and research centres, drawn during last decade by Commissions appointed by the President of the State Mining Authority in order to investigate reasons and circumstances of incidents, which till now, could not have been accomplished because of financial reasons. Furthermore, the paper presents basic assumptions of the Strategic Research Project Improvement of work safety in mines, announced by the National Centre for Research and Development at State Mining Authority?s President request.

Aug 1, 2013

By C. R. Edwards

"Since the first commercial extraction of uranium in the early 1940s, the range of feasible process alternatives has greatly increased. This paper reviews process options to reduce extraction costs, improve efficiencies, effect safer operations, and lessen environmental impacts. Equipment and processes used in the past, in use now, and that could be considered for future use are described.BackgroundTwo billion years ago life on earth consisted solely of single celled creatures of the simplest design (Gould 1989). Incredible as it may seem, uranium fission reactors were operating then also. In what is now western Africa, a series of natural reactors were fueled by rich uranium deposits in contact with underground rivers. Water from the rivers provided the moderator necessary to sustain the nuclear fission chain reaction. These primordial reactors ran down after about 600 000 years (Ontario Hydro 1989).Because it is ubiquitous in the earth&apos;s crust, humans have always been in contact with uranium. Mining of uranium, albeit not intentional, is ancient ; uranium minerals were embedded in ore veins mined for metals such as silver and copper.Uranium was discovered in 1789 in Berlin by an apothecary, Martin Heinrich Klaproth, who named the element after the recently discovered planet Uranus. The metallic element uranium, as opposed to its compounds, was extracted in 1841 by the French chemist Eugene-Melchior Peligot. The atomic mass of uranium was calculated to be 120, but the Russian genius Dmitri Ivanovich Mendeleev (famous and welcome everywhere except in Russia, where his liberal politics were detested by the Tsar), found this did not fit into his periodic table, and submitted a value of 240. Mendeleev was close; the exact atomic mass is 238.029.Henri Becquerel&apos;s detection of the radioactivity of uranium in 1896excited scientific study of the metal, but virtually no practical use was found for uranium outside of a minimal consumption as a colouring agent for glass and ceramics. Scientific interest intensified in the 19305. In 1933 Leo Szilard patented the concept of the nuclear chain reaction. While walking to work on a fine fall London morning and mulling over the problem of how to release atomic energy, he was stopped by a red light. He stood in thought and conceived the notion of the neutron-activated chain reaction before the light turned green. The patent was filed in 1934, and Szilard assigned it to the British Admiralty in order to keep it secret, in an honourable but ultimately futile effort to prevent the misuse of science (Bronowski 1973)."

Jan 1, 1992

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949

By E. C. Goodhue, R. D. Coleman, I. E. Puddington, A. F. Sirianni

Iron ore samples containing apatite are fractionated to acceptable products by spherical agglomeration methods. The phosphorus is upgraded by a factor of 10 at an elevated pH. High-grade iron products are obtained in good yields from the tailings in a second step of the operation. The grade of the phosphorus separated appears to reach a maximum at about pH = 10; recovery of iron decreases below about pH = 4. Both the recovery and grade of iron are found to be reduced sharply above about pH = 8.

Jan 1, 1968

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

The Beloziminskoe deposit in Siberia is a large, potentially productive deposit of rare metals contained in ochreous apatite pyrochlore ores formed by weathering of a carbonatite. The ores are composed of pyrochlore, columbitized pyrochlore, monazite, apatite, magnetite, ferric and manganese hydroxide, titanic iron ore, zircon, hydromica, quartz, feldspar, and carbonates. A gravity-flotation enrichment flowsheet with application of cationic and anionic collectors has been developed. This flowsheet allows for obtaining a pyrochlore concentrate containing 44.3% Nb2O5 and 1.89% P2O5 with recovery of 55.83% Nb2O5 as well as an apatite concentrate containing 39.2% P2O5 and 1.05% TR2O3 with recovery of 62% P2O5 and 43.23% TR2O3 from ores containing 0.92% Nb2O5, 16.9% P2O5 and 0.6% TR2O3. Rare-earth concentrate containing 40% TR2O3 with recovery of approximately 10% TR2O3 was obtained at the same time. Major losses of valuable elements are related to slimes, which make up more than 50% of the ground ore. The niobium concentrate does not meet the phosphorus and radionuclide concentrations needed for the production of ferro-niobium. Acid leaching and sulfatization provided a high level of phosphorous and radionuclide removal. Conditions include hydrochloric acid pre-leaching at 75- 80°C with an 18% HCl solution for four hours and low-temperature sulfatization of acid-leached concentrate at 160-180°C for one hour followed by water leaching of the residue. The apatite concentrate could potentially be processed using nitric acid leaching. This technology is based on decomposition of apatite concentrate with 55-57% strength nitric acid with transfer of rare-earth metals into solution in the form of ammonium phosphate. This technology recovers a rare-earth concentrate containing 95% TR2O3 with extraction of 86%, and highly concentrated polynutrient fertilizer (ammophos) with phosphorus extraction of 95%. The completed research shows how complex multicomponent ores of residual soil may be processed for the extraction of niobium, phosphorus, and rare-earth products.

Jan 1, 2016

By Donald MacFadgen

Since 1950, a total of 164 miles of levels and rooms have been roof-bolted in the collieries of the Dominion Coal Company. Roof bolting is an efficient and economic method of sup-port where heavy timber sets or steel booms are necessary for temporary roof support, or where conventional methods of support interfere with the passage of mechanical mining equipment. This paper discusses present roof bolting practices and special bolting applications. THE practice of roof bolting in be collieries of the Dominion Coal Company dates from 1950, when preliminary studies and experiments were carried out in a mechanized room and pillar section of Dominion No. 20 Colliery. These studies were made in close liaison with members of the United States Bureau of Mines who were conducting similar studies. Following the successful application of roof bolting in No. 20 Colliery, this method of roof support was introduced into other collieries

Jan 1, 1963

By M. Drozd, M. Somppi, Z. F. Yamak

"Activated carbon is used to recover gold in solution from various gold circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes; however, the characteristics and durability of the activated carbon can vary. Handling this medium poses challenges when fine carbon losses occur in the CIP, CIC, and CIL circuit discharge. Additionally, adsorbed gold on carbon fines can be lost to the discharge. The studies in this paper aim to standardize laboratory methods for testing activated carbon qualities specific to the gold industry. The investigation focused on size distribution, platelet content, wet attrition resistance, gold kinetics, and gold loading. The results demonstrate that a 96 h attrition test and a gold loading test form a basis for ranking carbon samples based on expected economic performance of the plant. ¦ KEYWORDS Activated carbon, Carbon attrition, Carbon ball-pan hardness, Carbon evaluation, Carbon fines loss, Carbon turnover RÉSUMÉ Le charbon actif sert à récupérer l’or en solution dans diverses conceptions de circuits de broyage d’or, notamment les procédés de charbon en pulpe (CIP, de l’anglais carbon-in-pulp), de charbon en colonnes (CIC, de l’anglais carbon-in-column) et de lixiviation au carbone, ou charbon au lixiviat (CIL, de l’anglais carbon-in-leach). Toutefois, les caractéristiques et la durabilité du charbon actif varient. La manipulation de ce milieu pose des problèmes dès lors que se produisent des pertes de carbone à grain fin dans la décharge des circuits CIP, CIC et CIL. Par ailleurs, l’or adsorbé sur les fines de charbon peut se perdre durant la décharge. Les études réalisées dans le cadre de cet article visent à normaliser les méthodes de laboratoire pour tester les qualités du charbon actif spécifiques au secteur de l’exploitation aurifère. L’étude portait sur la composition granulométrique, la teneur des plaquettes, la résistance au frottement humide, la cinétique de l’or et l’adsorption de l’or, à savoir la capacité du charbon actif à adsorber l’or sur une période spécifique. Les résultats ont montré qu’un test de frottement de 96 heures et un test d’adsorption de l’or constituaient le fondement d’un classement des échantillons de carbone du point de vue économique en vue de trouver l’échantillon générant le meilleur rendement des usines. ¦ MOTS CLÉS charbon actif, dureté de la batée des billes de carbone, évaluation du carbone, perte de fines de charbon, renouvellement du carbone, résistance au carbone INTRODUCTION The use of activated carbon for gold extraction is among the most common processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on reducing gold loss to tailings. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes. Granular activated carbon (Figure 1) is widely used for gold extraction from slurries containing gold-cyanide complexes. This activated carbon—produced from charred coconut shells—is well suited because of its adsorption kinetics, gold-loading capacity, attrition resistance, and ability to be reactivated. The extraction process using activated carbon technology involves adsorbing gold from an aqueous leachate; the gold is dissolved using a cyanide salt and consequently a dicyanoaurate(I) ion (Au(CN)2–) is formed, as noted in equation 1."

Jan 1, 2019

By Y. Mitani, H. Ikemi, K. Kitamura, H. Honda

"Instead of carbon capture and geological storage (CCS) that does not rely on structural aquifers, injecting carbon dioxide into sedimentary rock deep underground has been considered. For advection velocity of the fluid is slow, the permeability of sedimentary rock deep underground is low. In order to perform the CCS on the low permeable sedimentary rock, it is necessary to clarify the behavior of long term storage properties of carbon dioxide (CO2).In this study, the permeability and storativity of CO2 injected into low permeable rock has been evaluated. The injection of supercritical CO2 has been conducted on the specimen of Ainoura sandstone (unit weight: 2.39 g/cm3, porosity: 11.9 %) saturated with water by using flow pump method. The experiment has been set up to reproduce the similar condition of deep underground reservoir under 20 MPa confining pressure, 10 MPa pore pressure, 35°C temperature and 3 µl/min CO2 injection rate. In order to prevent an increase in pore pressure, the boundary condition on the outlet side of specimen has been kept a constant pressure.As a result, it has been possible to observe step by step the change of the differential pressure between both ends of specimen. Furthermore, the relative permeability and specific storage of rock under supercritical CO2 injection has been examined by the theoretical analysis of flow pump permeability test incorporating Darcy’s law for two-phase flow. It is observed that CO2 has been transmitted gradually while CO2 stored in the rock. It is also clarified that residual water has existed in specimen after showing the constant differential pressure in the end of the experiment. Using the results of the experiment, 3D core-scale flow-simulation by using TOUGH2 has been conducted due to confirm the flow of fluid and CO2 distribution in the specimen. From the experimental results and analytical solution to them, permeability and storativity are identified, and simulation results support the validity of the experimental results."

Jan 1, 2015

By CRO CRO

Elk Valley Coal?s Cheviot Project is located in the Alberta foothills south of the town of Hinton. The mine has been in operation now for the 3 years. The start up and subsequent operation of the Cheviot project has been directly influenced by the Cardinal River Mine. As the Cardinal River Mine was winding down due to reserve depletion in 2004, the price of seaborne traded metallurgical coal jumped to record levels and customers began aggressively seeking new sources of supply. Several months later, the owners of Elk Valley Coal decided to begin mining at the Cheviot mining area, extending the life of the area?s operations by over 25 years. The Cheviot Project had been delayed by low coal prices, ownership changes and a complicated and lengthy regulatory process fueled in large measure by stiff opposition from a number of major environmental organizations. Chief to the startup of the project was the construction of a 23-kilometer-long haul road that would connect the new coal measures to the existing Cardinal River processing and rail facilities. Construction of this road was completed with the first coal truck making its first trip in October 2004. This paper will look at some of original assumptions, the actual mining experiences and the lessons that were learned while moving from the drawing board to the current development as it exists today.

May 1, 2007

By G. Armand, A. Noiret, D. Seyedi, J. Morel

"Clay formations in their natural state exhibit very favorable confining conditions for repository of radioactive waste because they generally have a very low hydraulic conductivity, small molecular diffusion and significant retention capacity for radionuclides. Nevertheless, one concern regarding the hydromechanical behavior around drifts in such claystone is the associated pore pressure field disturbance during excavation works. In the short term, the very low permeability leads to an almost “undrained” condition, meaning that the stress change due to face advance will create volumetric strains leading to an increase or decrease of pore pressure. If the effective stresses reach the failure level, the induced damage around these excavations might change the favorable properties of such formations. To demonstrate the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW) in the Callovo-Oxfordian claystone (COX) formation, the French national radioactive waste management agency (Andra) started in 2000 to build the Meuse Haute-Marne underground research laboratory (M/HM URL). The present paper illustrates observed pore pressure changes during excavation of drifts (˜5 m diameter), of micro tunnels (˜0.7 m diameter) and a borehole (˜0.15 m diameter). All these openings are parallel to the major horizontal stress at the main level of the M/HM URL. In drifts parallel to the major stress (i.e., when the initial stress field in the drift section is quasi-isotropic) an important increase followed by a drop of pore pressure is observed in the horizontal plane at the drift wall. These observations emphasize the impact of the in situ stress state and rate of excavation on the pore pressure and provide important insight of the hydro mechanical behavior of the COX claystone and the relationship between pore pressure and excavation induced fractures zone."

Jan 1, 2015

By Paul J. Beck

The impact of mining development on the environment can be minimized through comp careful construction and accurate monitoring. Key to meeting these objectives is t information at all stages of design, development, operation and decommissioning. This paper will describe cost-effective means of gathering and managing reliable fiel groundwater flow and surface water regime within and surrounding the mine site, as localized contaminant plumes associated with mine operations, and monitoring ground quality. Recent research has led to the development of inexpensive, easy to install syst sampling/monitoring from different zones within a single borehole. Advances in elect developed small diameter probes and pumps for measuring water levels and taking wat continuous monitoring stations in remote areas can be colldeacttaeldo gaguetrosm aatnidc adlolwyn luosaidnegd from a central facility using telemetry systems powered by direct, battery or solar radio frequency, landline or cellular telephones, and satellite. Two case studies will illustrate the use of datalolgagregres sacnadl et eblaesmient rwyi dien mao nitoring sc and the use of multilevel samplers for managing a contaminant plume.

May 1, 2004

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By Ch. Enkhbold

Underground mining of minerals is becoming an increasingly complicated technological and ecological problem. It can be explained both by worsening of geological conditions of mining and by a specific character of mining industry, which, in contrast to processing branches of industry, intrudes into one of principal components of the nature ? the Earth&apos;s interior. At a traditional organization of mining industry, the entire volume of the produced rock mass is brought to the Earth&apos;s surface, where valuable components are extracted. This entails not only power over expenditure for long-distance transfer (especially in the vertical direction) of the waste rock forming a part of the original mineral, but also the formation of huge volumes of worked-out spaces. The latter leads (nature cannot stand emptiness!) to an irreversible development of geomechanical processes of shifting of overlying rock masses resulting in an irreparable damage of all surface structures located on the territory undermined by deep mining. Owing to their high productivity combined with low power consumption and instrumental compactness, novel bifunctional technological processes of minerals dressing successfully solve the problem of rock mass processing in underground conditions with subsequent operative disposal of final tailings of such underground dressing in the worked-out space. Besides, an integration of two processes into one is achieved, for example, a decrease in the rock mass coarseness with a simultaneous precise separation of valuable and waste components.

Aug 1, 2013

By Rodrigo Madariaga, Tracy T. Morris

The practice of stripping copper starter sheets from titanium blanks to be used in a conventional electrolytic tankhouse has been around since the advent of Electrometallurgy. Historically it has been done manually, utilizing many people to produce in some cases thousands of starter sheets per day. Some other conventional tankhouses have successfully converted to using mechanical means to strip starter sheets or have made the switch to permanent cathodes and although robotics have been around for quite some time they have not been used to strip starter sheets until recently. The Amarillo Copper Refinery began using robotics to strip several years ago and the details to how this came about and how the robots work will be described. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By Ralph J. Holmes

"An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and sold commercially is crucial to resource definition, effective resource utilisation, plant design, process control, metallurgical accounting and finally quality control to ensure that contract specifications are met and equitable payment is received for product sales. However, the responsibility for sampling is often entrusted to personnel who do not fully appreciate the significance and importance of collecting fully representative samples for analysis, and they seem satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. There is really little point in accurately analysing samples if they are not representative in the first place, because the resultant analyses can be seriously biased and the effort taken to carefully analyse such samples is largely a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts and significant revenue losses due to poor sampling practices at the point of sale. Consequently, it is critical that sampling is given the attention it deserves as the first important step in the quality measurement chain. The golden rule for correct sampling is that all parts of the ore, concentrate, slurry or other material being sampled must have an equal opportunity of being collected and becoming part of the final sample for analysis."

Jan 1, 2016

By S. Papanakli, Th. Rondoyanni, N. Sabatakakis, K. Kavoura, G. Tsiambaos

"A representative composite fault-related landslide of the Corinth Gulf graben named “Panagopoula” is reported that considered to be one of the most prone to slope instability sites along the main motorway and railway connecting Athens with the city of Patras. The presence of tectonically highly sheared and weathered geological formations, including Alpine basement (mainly flysch) contributes to the site instability, triggered/reactivated by seismic activity and heavy rainfalls. Although a series of remedial measures have been already constructed, the inclinometer readings during the last twenty years time period show a continuous very slow movement which indicates that the landslide is still ""active"". This fact has resulted to divert the axes of the new motorway and railway through twin tunnels which are under construction. INTRODUCTIONThe spatial and temporal evolution of landslides in the case of structurally complex slopes is lithologically and often structurally controlled while their type and frequency are mainly related to tectonic and lithological anisotropy (Baron et al. 2005; Hradecky et al. 2007). The triggering mechanisms mainly include: (a) excessive rainfall generating high pore pressure and (b) strong earthquakes resulting in dynamic loading conditions at the failure surface. Data such as past earthquakes or the precipitation records are useful to be gathered when a landslide model is examined since they could act as a landslide triggering mechanism. Recording of the movement through surface and inclinometer measurements as well as combination of the above information with historical records of failure could lead to a more accurate estimation of the location of the failure surface and understanding of the landslide mechanism.Slope instability in the southern segment of the Gulf of Corinth, Northern Peloponnesus, Greece, is ubiquitous and ranges from deep-seated bedrock failure to secondary earth flows in recent deposits. In this part of Greece, the periodically induced landslide events triggered by heavy rainfall, earthquake and anthropogenic activity are closely related to active fault tectonics. The Gulf of Corinth is considered as a typical example of a relatively simple asymmetric half-graben with major border faults to the south and a flexure of the northern shore. Panagopoula landslide is located along the trace of a WNW trending normal fault (dipping northwards) (Figure 1). The area is considered to be one of those most prone to slope instability along the E95 motorway and railway connecting Athens with the city of Patras."

Jan 1, 2015

By Antoine Fournier, Karen St. Seymour

"Responding to market developments, interest in locating deposits of wollastonite has grown significantly. The many occurrences in the Grenville marbles of Quebec can be grouped into disseminated type and discordant vein-type deposits. Disseminated-type wollastonite occurrences have the disadvantages of lower grade, the need for more elaborate mineral separation, and failure to meet ""long grain"" technical specifications. Vein-type deposits have better grades and technical characteristics; exploration should be focussed on these and in the contact-metamorphic aureoles of fluid-rich intrusions. SOMMAIREEn réactions aux nouveaux de bouches, l&apos;interet pour les gîtes de wollastonite a crû de façon marquée. Les nombreux indices sis dans la province de Grenville au Québec peuvent être regroupes en deux catégories soit: les indices dissémines et les indices en veines discordantes. Les indices dissémines ont le désavantage d&apos;être moins enrichis, de requérir une séparation minéralogique plus complexe, et leur wollastonite ne possède pas le degré d&apos;acicularité voulu. Les indices en veines sont plus enrichis en plus de rencontrer les critêres techniques; les efforts d&apos;exploration devraient se porter vers ce type de gites et aussi, sur les auréoles métamorphiques de contact d’intrusions riches en fluides."

Jan 1, 1992