Search Documents

Real Time Monitoring of Cemented Paste Backfill Introduction Methods ?how to instrument a Long Hole stope Key Results from 2 case studies: barricade pressures and displacement, in-stope pressures Importance of Real Time Monitoring How binder, rise rate, cement content affect fence pressures

May 1, 2010

By Saikat Chatterjee, Xintong (Brett) Liu, Kinnor Chattopadhyay

Magnesia carbon bricks are commonly used in BOFs and are generally pre-heated before the BOF goes into service. Owing to very stringent emission regulations, the BOF pre-heating process need to be controlled and optimized so that, the emission standards are met. One of the major concerns in organic emissions are its stringent limits on emission rates and total volatile emissions. In the present work, an attempt has been made to integrate CFD and Thermodynamic models to predict the emission rate of volatile organics during the pre-heating process. A one dimensional heat transfer model was developed using visual basic and then integrated with thermodynamics calculations using FactSage 6.4. The parameters that affected organic emissions were the pre heating procedure, gas composition of the burner, heating rate and type of the burner. Typical composition of MgO-C bricks and binder materials were obtained from literature and vendor data sheets. Chemical reactions between organic materials, refractory and burner gasses were considered. The model predictions indicated that certain burner conditions could destroy all organics before it exits the vessel while other conditions needed the use of an after burner at the mouth of the vessel. The model was also able to predict the organic emission rates based on the chosen pre-heating profile. This kind of predictive model will be very useful for the steel industry and enable them to justify permit limit applications and stick to the limits by fine tuning their pre-heating process.

Jan 1, 2015

By K. B. Young

Possibly the most complex fatigue problem associated with the development of the axial-flow 'gas turbine is discussed in its broader aspects from the metallurgical viewpoint. Reference is made to nodal patterns, interference diagrams, etc. The use of such data in analysis of a turbine :blade failure is illustrated. Special attention is given to the influence of some metallurgical variables affecting fatigue strength and, in particular, heat treatment is shown to have a pronounced effect on .the relative fatigue and creep strength properties of a nickel-chromium-cobalt base alloy suitable for turbine blade applications.

Jan 1, 1958

By Chris Brothen

The introduction of new technology in mine operations has provided real opportunities for increased efficiencies and production gains which translate into enhanced profits. Computing and network technology usage has become integrated into surface mining operations and on average these investments in technology have proven beneficial for efficiency and productivity improvements. Embracing new technologies however, does not guarantee positive results. The expectations or improvements derived through the technology must be confirmed and clarified well before implementation. Tire Pressure and Temperature Monitoring Systems are an excellent example of an existing technology that can provide full time automated performance measurements of tires operating under harsh conditions and environments. Prompt warnings or alarms signaling when a tire has exceeded operating capacities will provide savings through lowered maintenance costs and increased productivity. To truly quantify the projected savings in tire life, fuel consumption, and increased levels of production, all costs associated with the technology, both direct and indirect must be considered. Apart from the initial cost of the system implementation, ongoing maintenance and support costs must be considered as well as the costs of system integration into existing mine operations

May 1, 2008

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952

By F. P. Agterberg

"IntroductionTHE KNOWLEDGE about the mineral resources in a region ranges from relatively precise ore-reserve estimates for known deposits to probabilistic estimates concerning the speculative resources which may be discovered in future at greater depths and in the less-explored parts of the region. Previously developed probabilistic methods for regional resource evaluation (1) are based on the following two assumptions.(1) The probability that a specific block of rock, or part of a region close to the topographic surface, contains undiscovered deposits can be estimate d by weighting selected geological, geophysical or geochemical parameters for that block. The weights are computed by considering similar environments which are known to contain deposits.(2) Some of the characteristics of the undiscovered deposits, such as ore tonnages and average grades of metals contained in the ore, can be evaluated by considering probability distributions f or known deposit data. These methods were initially applied to Precambrian deposits in the Abitibi Volcanic Belt of the Canadian Shield (1).Since 1972, statistical methods for quantitative resource evaluation have been applied to the occurrences of the mainly Paleozoic base metal deposits in t he Canadian Appalachian Region. The objectives of this project (Project Appalachia) have been discussed by Leech (2) in a paper that introduces 8 papers with results of the exploratory data analysis. Project Appalachia represents an effort to develop and apply methods of combining information and concepts from regional geology, metallogeny and geomathematics for computer- aided regional mineral resource evaluation."

Jan 1, 1977

By Dong-Hyeun Koh, Yun-Soo Lee, Min-Seok Kim, Hyoung-Wook Kim

High strength AA7068 (Al - 7.88 wt.% Zn - 2.68 wt.% Mg - 2.07 wt.% Cu) aluminum alloy strip was successfully fabricated by horizontal-type twin roll casting. A simulation technique was used to obtain the range of casting conditions for fabricating strip without defects. The cast strip with thickness of about 5 mm was hot rolled, intermediate annealed, cold rolled to final thickness and subsequently annealed at various temperatures. Tensile properties of annealed and the aged specimens were evaluated at ambient temperature. Tensile strength and elongation of the annealed sheet are about 365 MPa and 28%, respectively. Also, the tensile and yield strength after the aging at paint baking condition (180 °C x 0.5 h) are 586 MPa and 551 MPa, respectively. Therefore, it is expected to show good formability prior to press or stamping and also provide high dent resistance after paint baking treatment.

Jan 1, 2015

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By James B. Templeton

"IntroductionWith the steady rise of the cost of coal and freight, the time is now ripe for an investigation into the feasibility of using the heat pump for heating purposes in fairly remote industrial areas.The gold mines of northern Ontario seemed to be a most likely place for the application of the heat pump.It was decided that the first step in the investigation would be to determine what economic advantage was to be gained by using the heat pump and thereby determining whether a further and more detailed research programme was warranted.If we can use the heat pump with economic advantage, we can reduce our mining costs and make a worthwhile contribution to our national economy by reducing the import of U. S. coal.The investigation was conducted under the auspices of the Nipissing Fellowship and directed by Professor R. E. Barrett of the Department of Mining Engineering, University of Toronto.With the able guidance of Mr. C. S. Gibson, of the Mines Accident Prevention Association of Ontario, the author visited the following mines: Mcintyre-Porcupine, Delnite, Dome, Lake Shore, Wright-Hargreaves, Kirkland Lake, Macassa, and Kerr Adcliso11.In all cases, the management and technical personnel of these mines were most co-operative and helpful in supplying information and ideas.It should be emphasized at the outset that the design and operation of the heat pump itself is by no means complicated or even new. The reason we hear so much about it today is because there have been improvements in compressors, motors, and heat exchangers in the past few years, and because fuel and freight rates have risen to such a point that, in some cases, the heat pump now has an economic advantage over other methods of heating."

Jan 1, 1950

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company's share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company's working capital is approximately $1,500,000.

Jan 1, 1963

By L. Drisdelle, S. Gendron

"Survival in today's business climate requires participation of all employees in a Total Quality Management Program encompassing everything - ""safety, quality of products, quality ofet1ch and every job done, and of course production "". We all know what needs to be accomplished, but struggle with how to do it, especially in an industry which has not always experienced management/union cooperation, and mistrust is still present.This paper describes a process to improve team work and employee involvement in Inco's nickel carbonyl refinery at Copper Cliff The process involves facilitatorship training for all employees, and a system for reinforcing and accomplishing the required behavioural change. The system is described in detail and a number of examples are presented. At the refinery, the staff is starting to understand as Max DePree recently wrote ""Without Quality Behaviour, you cannot have Quality Product"". IntroductionThe Copper Cliff Nickel Refinery (CCNR) is Inco's largest and most modern nickel refinery, which celebrated its twentieth year of successful operation in April 1993.The heart of the refinery is the Inco pressure carbonyl (IPq plant which produces high purity nickel pellets and specialty powders by refining an approximate 80% nickel granule feed. The carbonyl plant is a modem chemical plant with very special and demanding requirements for safety and environmental protection due to the toxic nature of the refining gas.Since 1987, there has been an emphasis at CCNR on a comprehensive Total Quality Improvement (TQI) Program which was designed based on recognizing customers' needs for improved systems for quality management. This program is customer oriented and comprises such elements as team organizational concepts, customer audits, process assessment and internal quality auditing.A detailed review of progress was made in early 1991 and it became apparent that the ""ownership"" of the TQI program was not broad based. In fact, the program was very much a staff driven effort and fell far short of total employee involvement and relentless continuous improvement that are now considered essential to remain competitive and stay in business.Inco staff has now come to regard that early phase of our TQI program as ""the technical aspects of total quality improvement"".The safety experience was also puzzling. Even though the safety statistics were good with an average lost time frequency of 1.6 for the last five years, the perfonnance improvement had plateaued and remained pretty much the same. Clearly a new approach was required if significant progress and continuous improvement was to be made."

Jan 1, 1994

By Dorothy Walters

As an increase in the number of producers alters fact ors affecting supply, long-term prospects in traditional markets for many minerals weaken. At the same time, conflicts between national and international objectives undermine existing competitive elements in mineral markets and Canadian costs escalate. Such changes may dramatically alter the environment in which the mining industry operates.

Jan 1, 1979

By R. H. Fett

T HE APPROACH to maintenance must always be ?completely positive: there must be no question of putting off difficult problems until it is more convenient to tackle them. By this it is meant that a piece of machinery or equipment which, by experience, is known to be due for a check should not, merely because it appears to be operating satisfactorily, be left until it reaches a critical .condition and breaks down. The mentality of the Maintenance Manager must be completely orderly and methodical and he should, in fact, possess a ledger-book mind, having a debit and credit outlook. The debit side would be that applying to time out of service, cost in wages, material, personnel involved, etc., and the credit side that relating to continuous operational time of the locomotive and therefore to the ultimate benefit of the mine and the personnel who work there. The Maintenance Manager is not concerned with design problems, and although he and the personnel under his jurisdiction are not engaged in productive work, he and his staff do, nevertheless, add greatly to or detract from the overall efficiency of the organization. Provided the machinery placed in his care is good to start with, he must take the best steps he possibly can to keep it running. However, he may, on occasion, be forced to improvise and this is where the ingenuity of a clever man rises to the occasion.

Jan 1, 1956

By Y. Serres

In the past, conventional reflection seismic techniques were not very successful when applied to typical mining exploration: they lacked resolution in the shallow range or were not cost effective. By combining a light earth tamper source, special geophones and field procedures, a stacking process of the returning seismic events using a microprocessor system, and a sophisticated sequence of adapted digital data processing, Mini-Sosie achieves high resolution in the 100-ft to 4000-ft range. Additional advantages result from the very quiet nature of the source and flexibility of the system. Although Mini-Sosie might be used in the refraction mode, or for well velocity logging, it has found its main applications with the reflection technique.

Jan 1, 1978

By F. Nava-Alonso, E. Pérez-García, A. Uribe-Salas, J. C. Fuentes-Aceituno, A. A. González-Ibarra, E. N. Castillo-Ventureño

"Precious metals cannot easily be recovered from tellurides by the standard cyanidation process. This work assesses the cyanidation of synthetic samples of precious metals tellurides and explores some alternatives for the leaching of these species (i.e. cyanidation in presence of lead nitrate and thiosulfate leaching). For this purpose, three chemical systems were studied: (1) cyanidation of silver telluride and the effect of lead (II) nitrate addition, (2) cyanidation at high alkalinity and high cyanide concentration of a gold-gold telluride sample containing tellurium and tellurium dioxide, and (3) thiosulfate leaching of silver telluride employing cupric sulfate as oxidant and EDTA as complexing agent for copper. Results showed that standard cyanidation dissolves 10.5% of silver from silver telluride in six hours, while with the addition of 100 mg/L lead increased the silver dissolution up to 100% in the same time. The standard cyanidation of the gold-gold telluride sample dissolves only metallic gold in six hours, while when cyanide concentration and pH were increased, gold and gold telluride were simultaneously dissolved. Finally, thiosulfate leaching dissolves 43.1% of silver from silver telluride in six hours.INTRODUCTION Precious metals tellurides are classified as refractory ores due to the difficulties associated with processing them by the standard cyanidation method. The increasing presence of gold/silver tellurides in some deposits around the world, specifically in Sonora, Mexico, requires new approaches to the cyanidation process, or the development of new leaching techniques. Treatments have been proposed for the recovery of gold and silver from their tellurides, including roasting, preoxidation, cyanidation with lead nitrate, and the use of leaching agents other than cyanide (Zhang, et al., 2010; Ellis and Deschenes, 2016). This work presents preliminary results of three options to recover precious metals from pure tellurides: the cyanidation of gold telluride at high cyanide concentration and high alkalinity, the addition of lead nitrate to the standard cyanidation process, and the use of sodium thiosulfate as leaching reagent."

Jan 1, 2017

By Diego L. Romero, Joy P. Romero

"IntroductionThe purpose of this paper is to explain the theory and demonstrate the industrial applications of electrostatic separation. Wabush Mines' use of this type of processing for the concentration of iron ore is unique in the industry. Other minerals are concentrated electrostatically but the process is not widely used.Typical minerals separated by electrostatic separation techniques are:Non-ConductorsAnhydriteApatiteBariteBastnasiteBerylCalciteChrysotileCorundumDiamondEpidoteFeldsparsFluoriteGarnetGypsumHornblendeKyaniteAcmiteAugiteBrookiteCassiteriteChalcopyriteChromiteColumbiteCopperDaviditeEuxeniteFerberiteFrankliniteGalenaGoldGraphiteHematiteMica (Biotite)Mica (Muscovite)MonaziteOlivinePerovskiteQuartzScheeliteSideriteSillimaniteSpheneStauroliteSulphurTopazTourmalineXenotimeZirconConductorsIlmeniteIlmenite-( High Iron)IlvaiteKoppiteMagnetiteMarmatiteMolybdenitePyriteRutileSamarskiteSphaleriteTantaliteWolframiteWulfeniteThe limitations of this process are:1. There must be a difference in conductivity between the minerals being separated.2. The size range must not be very wide.3. The specific gravity of minerals being separated should be similar or the minerals to be pinned should be lighter. 4. The feed must be dry.5. The particle shape should be more or less uniform. 6. The feed must not be high in true middling particles."

Jan 1, 1989

Commercial SOFC systems will likely utilize hydrocarbons or hydrogen produced from hydrocarbon fuels and therefore will likely be exposed to sulfur impurities. Conducting-Atomic Force Microscopy (C-AFM) is a scanning probe microscopy technique which maps both sample topography and conductivity with tens of nanometers resolution. In Ni-YSZ, C-AFM measures the resistance of the metallic network at scanned locations, with the ability to differentiate between interconnected and isolated metallic particles. We have applied C-AFM to Ni-YSZ SOFC anode materials, with the goal of monitoring changes in the conductivity of the Ni anode network resulting from SOFC degradation processes, such as H2S poisoning.

Jan 1, 2005

By Mike D. Riley, Alan V. Bell, Ernest K. Yanful

Acid mine drainage (AMD) research under the MEND program has been ongoing since 1988 at the Heath Steele Mines waste rock piles including sulphide material, outside Newcastle, NB. In 1989 approximately 10,000 mt of waste rock was placed on a prepared sand base with an underlying impermeable membrane. The waste rock pile was heavily instrumented for measuring oxygen concentrations and temperatures. In September 1991, a composite soil cover designed for the Heath Steele climatic conditions, using local soils, was placed over the pile, creating a totally enclosed system. Moisture content and oxygen probes were installed within the composite soil cover to monitor changes within the soils over time, while two large-size lysimeters were installed below the cover to monitor the hydraulic conductivity of the cover. The waste rock site has been monitored on a monthly basis since installation of the cover, for performance of both cover and waste rock. The monitoring shows very clearly that the placement of the composite soil cover has had a major impact on the generation of AMD. Major reductions in temperature and oxygen concentrations within the waste rock pile indicate that the cover has significantly inhibited the oxidation reaction that generates the AMD. Performance data have shown that the cover has maintained its integrity under the climatic conditions of the area.

Jan 1, 1995

By A D. Turnbull

In Canada, although some research on extraction metallurgy is carried out by the universities and by government, the primary responsibility for the research necessary to the mining industry rests on the industry it-self. Automation is coming more slowly to the mining industry than to others, partly because of the problems of instrumentation. Operations research methods are, however, coming into use. Some new developments in the extraction of aluminum, in iron and steel, in pyrometallurgy and in pressure leaching of nickel, copper, zinc and lead are briefly outlined. Mention is made of uranium and the reactive metals. The importance of the by-product metals, notably antimony, bismuth, gallium, germanium, indium and tellurium, in the development of the electronics industry is also mentioned. The trend toward co-operative research by groups of producers, to develop markets for their products, is noted. In conclusion, there are a greater number of trained scientists, as well as larger amounts of scientific knowledge, available to the mineral industry than ever before, and, if properly used, this will result in great benefits to the industry and to Canada.

Jan 1, 1963