Search Documents

By Y. Mercadier, M. Ait-Ali, M. Dostie

"This paper presents the results of an analytical study to assist in the design of blast furnace tuyeres, including a prediction of the heat transfer process.IntroductionA blast furnace tuyere must be made of a material which must con serve its geometric and structural integrity in the environment of the fire-ball of the furnace. It must be cooled by a fluid forced through its internal cavities in such way as to keep its maximum temperature below the allowable limit. The prediction of the convective heat transfer coefficient inside the tuyere is of great importance in the design of new tuyeres with increased service life. We have developed a computer program which can predict the convective heat transfer coefficient for two-phase flow. This paper shows how the program work s and how it can be used for the numerical simulation of tuyeres.To simulate the h eat transfer conditions in water-cooled tuyeres, one has to predict:a) The heat flux (radiation and convection) generated by the combustion gases. This was evaluated using the single-zone gas-furnace model. This model yields results which are of the right order of magnitude. A more fundamental study of radiation heat transfer based on combustion and gas concentration s will be reported in a future publication.b) The local convective heat transfer coefficient at all points with in the tuyere.Prediction of the Convective Heat Transfer CoefficientTo calculate the convective heat transfer coefficient for refrigerant stream, semi-empirical correlations developed by the nuclear industry were adopted. These correlations permit us to analyze the entire range of the convective boiling range, as shown in Table 1. Our first attempt, with a single-phase flow correlation, has shown the need to take nucleate boiling into account."

Jan 1, 1982

By Eliodor Stoian

PRESSURE information has earned a place of recognition to almost everyone interested in oil and gas production. This interest is due chiefly to the multitude of uses to which it can be put. A sub-surface pressure test, conducted for as little as $60, may yield data worth many times its cost. To the uninformed, the testing techniques may seem complex. Fundamentally, however, they consist merely of the application of common sense. At one time, sub-surface pressure data were used only in identifying individual well problems and in finding appropriate solutions. Today, it is generally acknowledged that sub-surface pres-sure .data are essential for the proper evaluation and exploitation of oil and gas pools. The following is a review of significant applications of sub-surface data with regard to: (A).-Development (B) .-Completion and work-overs (C) .-Production (D) .-Reservoir engineering (E).-Proration (F) .Other applications of pressure data of a more general nature.

Jan 1, 1958

In April, 1961, a large pillar was removed by blasthole mining methods at Inco's Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By H. A. Steane

THIS PAPER describes the re-grind section in the 2,000-ton per day, lead-zinc flotation mill of Canadian Exploration Limited, near Salmo, B.C. There are two re-grind units in operation, one in the lead circuit, and one in the zinc circuit. In each unit, the rougher concentrate is re-ground ahead of the cleaning circuit. These re-grind units have made valuable improvements in the concentrate grade, and with no loss in recovery by over-grinding galena or sphalerite. Since the initial installation of this re-grind section, the plant throughput has been increased gradually from 1,600 tons to 2,000 tons per twenty-four hours, and, as shown by the screen analysis of mill tailing, a coarser overall grind has been accepted, from 55 per cent to 45 per ?cent minus 200 mesh. There has been no increase in grinding capacity, but two mills have been taken from the main grinding circuit and used for the re-grind circuit.

Jan 1, 1958

By P. Moreno

ABSTRACT: The Maras salt terraces, located between Cuzco and Urubamba in the Andes (southern Peru), are living examples of traditional Incan salt production, where present-day artisanal miners produce salt from shallow pans by solar evaporation. In these terraces, natural spring water, eight to nine times saltier than seawater, is used to produce the salt. The field observations and chemical analyses show that the poorly crystalline traditional salt is finer in particle size and contains impurities such as dolomite and gypsum. These differences are the result of shallow pond depth, contamination from wall erosion, and the nonsequential mode of salt crystallization.

Jan 1, 2011

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By D. M. Ramsey

HIGH-INTENSITY magnetic separation as now practised in the commercial treatment of a large variety of industrial minerals is a com-paratively recent development, having had its practical beginning about ten years ago when it became necessary to devise more effective methods for the purification of the electric furnace abrasives and refractories-silicon carbide and fused aluminium oxide. The fundamentals of magnetic separation are, of course, very well under-stood; bur while very, very old in principle, the process has, in recent years, been developed to a point of far greater usefulness than heretofore. In fact, until the development of the high-intensity process,. magnetic separation was limited largely to the removal of tramp iron? with magnetic pulleys and the removal of the very highly magnetic portions of industrial minerals by means of horizontal conveyor-belt-type separators. All magnetic separation processes depend for their success on the fact that various materials are kinetically influenced to a greater or lesser degree by the force that we speak of as 'magnetism'. We have now come to regard 'magnetic separation' and 'high-intensity magnetic separation' as two different and distinct methods. However, both depend upon the reaction of a particle when placed in a magnetic field. The common types of magnetic separators quite generally operate on the principle that a magnetic particle can be lifted by a powerful magnetic force from a stream of material moving on a belt or other type of conveyor. The application of the force removing magnetic material by this scheme is directly opposed to the force of gravity and is, therefore, limited to sub-stances of a relatively high order of magnetic susceptibility, such as metallic iron and magnetite. Until a few years ago, one very important principle was almost entirely overlooked. Practically every substance is susceptible to some extent, at least, to magnetic attraction, and by the application of a magnetic force great enough, and properly applied, separations of materials heretofore considered 'non-magnetic' can be accomplished.

Jan 1, 1937

By D. G. Crosby

This paper defines the Canadian offshore areas, comparing the juridical continental shelf with the physical one. The question of jurisdiction and ownership is dealt with, and the setting out of resource administration lines to divide areas of federal and provincial administration is explained and illustrated. Offshore activity is reviewed and prospective areas for future work are mentioned.

Jan 1, 1969

By H. Feldheiser

Acid resistant brick linings are state of the art for anti-corrosion linings in tanks for high pressure acid leaching (HPAL) treatment. The design of these brick linings has to take into account the almost non-elastic behaviour of the brick lining inside a relatively highly elastic steel vessel. There must be tools and data available to determine for the steel vessels the thermal growth plus the pressure expansion and for the brick lining the linear thermal expansion and the chemical swell. Thermal shocks and pressure drops are not regular operating events but their negative influence on the lifetime of a brick lining has to be a part of the engineering study. Finite Element (FE) models as well as a lot of research and development on brick lining materials is the only way to find a path through the complex engineering work for pressure vessels.

Jan 1, 2004

By Roberto Pena, Cristhian Morales, Darwin Morales, Veronica Cambiaso

"This article makes evident the shortcomings of the current operation of oxygen pipes as well as the damages they cause and why they cause them. When focusing on the causes and effects of these drawbacks, it was possible to develop a new family of thermal lances that could pierce a taphole with the precision of a drill but with the capacity to complete the whole operation. Although efforts have been made to replace oxygen pipes since they are annoying, dangerous and inefficient, nobody had worked to improve the way the traditional oxygen pipe taps/perforates the furnaces and reactors tapholes. In fact, developments made in drills and robotic arms, have failed to replace the oxygen pipe, which despite their negative side effects have been used for more than a century. Observation and theory were key to radically transform this humble tool into a dependable and efficient support in the operation. A good news that it is worthwhile to share for the benefit of all of us, passionate about the world of pyro metallurgy.INTRODUCTION Normally, reports and papers prepared for conventions, symposia or other technical events related to metallurgy aim to relevant topics in the operational field, probably because in them lay the scale economies every company pursues. We intend to give relevance to a matter normally disregarded in operations, but that unmistakably vital: if the furnace or reactor cannot be bled, the pyrometallurgical process will not be completed. Besides, if the tapping task is difficult or is long delayed, the availability of the furnace will be reduced. Consequently, there will be a waste of energy and workers will be exposed to dangerous levels of radiation as well as to work overload and physical injuries Apart from these basic effects, in tapping operations where oxygen pipes are used, we can see serious damages in the smelting furnace, especially in the taphole components such as refractory bricks, taphole jackets and water cooled plates. This paper intends to show that taking care of the tapping task can significantly upgrade not only to the tapping operation itself, but also the whole plant productivity."

Jan 1, 2017

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the ClM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposits. Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. UranitnlHeiated studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to D were presented in previous issues of the ClM Bulletin, abstracts related to themes E and F are presented in this issue. The remaining abstracts will be presented in a future issue."

Jan 1, 1994

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949

By N. Campbell

"The fault under consideration follows a northerly trend past the west; side of the original settlement of Yell ow knife; which is situated 600 miles; north of Edmonton and 400 miles from the Northern Alberta Railway; terminus at Waterways; Alberta. The mining properties chiefly concerned; include the southern part of the Giant claims; on the east side of the fault; and the Con-Rycon-Demelt claims; on the west side 3 1/2 miles to the south.; Geological data were also obtained from the eastern part of the A.Y.E.; property; which lies south of the Giant claims; and from the Negus; Meg; Yellorex; and Kam properties; which are south and southeast of the ConRycon-; Demelt claims (see Frontispiece; also Fig. 5).Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault, which appears to be the greatest, resulted from the work of A. W. Jolliffe (formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply dipping dislocations of the earth's crust.In the winter of 1939, a mineralized shear zone named the 'Creek vein' was found on the Giant property. It was noted that the space relationship between this shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acid flows lying north of the Con property. Coupling this relationship with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear zone.As geological information became more extensive, certain weaknesses in this concept became apparent, and when spectacular orebodies were discovered on the Giant property in 1944 the question of possible faulted extensions became an important consideration. Consequently, in the spring of 1944, an extended investigation was undertaken, the results of which are embodied in this paper."

Jan 1, 1954

By Jef M. van der Zel

The idea of veneering rich yellow gold alloys with a low-melting, high expansion porcelain, has been a driving force for metal-ceramic research in dentistry. Since 1990, with the advent of the Carrara System (1), a low firing temperature veneering ceramic allowed the use of gold alloys with a lower content of platinum and palladium than the traditional gold-platinum ceramic alloys and thus a richer yellow color. The earlier high gold-platinum ceramic alloys contained at least 12 percent platinum group metals to allow for dimensional stability when firing the relatively high melting traditional ceramics. This amount of platinum group metals gave the alloys a greyish tinge which made them unattractively steel colored and difficult to present as ?high gold alloys?. In the 90?s the new generation universal low-melting, high expansion gold alloys gained market share at a steady rate, starting in Germany, and have now for a great part replaced the traditional gold-platinum alloys (Fig. 1). The first alloys contained 75 wt-% gold and up to 9 wt-% platinum or palladium. They provided a metal-ceramic system in which a gold alloy having an aesthetic yellow colour is fired on with a dental porcelain tailored thereto. The tailoring is meant in respect of compatible coefficients of thermal expansion, and compatible melting or softening points of metal and porcelain. The major concerns in the beginning were with thermal stability during firing, the thermal expansion coefficient of the alloy against the porcelain (compatibility) and the yellow color. In a later stage, alloys with gold contents in the range of 50-60 wt-% gold were developed in analogy with the pale yellow gold-reduced alloys that were formerly used for crown & bridge work and the white gold-reduced alloys used for metal veneering where gold was substituted in part by palladium.

Oct 1, 2003

By J. M. Ortiz, J. P. Bertini

"In mineral resource and ore reserve estimation, several sources of information are generally available, such as diamond drillholes, reversed-circulation drillholes, and blastholes, and originate from one or more sampling campaigns and are analyzed by one or more laboratories. In such a situation, the grade measurements may not have the same precision and one should distinguish between hard and imprecise data.This work aims at studying the impact of data imprecision in resource/reserve evaluation through two case studies on simulated deposits: a porphyry copper deposit conditioned to real exploration and production data, and a gold deposit simulated without any conditioning data. Several geostatistical techniques are used to estimate the grades of selective mining units from exploration samples, including kriging, cokriging, lognormal and indicator kriging. Two types of imprecision are examined— measurements with multiplicative errors and measurements defined as intervals. The results are compared to the simulated grades of the selective mining units from a statistical and economic viewpoint.The study concludes that imprecise measurements should never be discarded because they help to improve the estimates, and that simple methods such as kriging are as efficient as more sophisticated ones for resource/reserve assessment. Finally, a few indications on how to diagnose and model the data imprecision are given."

Jan 1, 2005

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

Research, whether applied or fundamental, is a human endeavour which increases our understanding of nature. It is insufficient to simply observe, explore, record and classify. It i necessary, as well, to fit the observations into a satisfying theoretical scheme; that is, to synthesize. Two examples of successful research programs in physical metallurgy are di cussed from this point of view. A pessimistic view is taken of the prospects for rapid growth of research activities in the Canadian metallurgical industry. THE term "research" is used indiscriminately to describe any intellectual or experimental activity which leads to a change in society. Proponents of various activities, ex-tending all the way from alloy development to subliminal advertising, use the status of the term for special advantage. With the Canadian Government entering upon a project of support to industrial research, it might be well to determine what definition is most in the public interest. As an academic, I have a rather jealous attachment to the definition that research, whether applied or fundamental, is a human endeavour which increases our understanding of nature.

Jan 1, 1963

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By M. S. Badollet

"The study of the physical properties of asbestos minerals requires a careful isolation of the fiber from the wall rock and, at a later stage, a comparison of these physical properties with those of fibers that have passed through the milling and beneficiation processes.The effects of mineral impurities, loss of fiber length and the formation of extreme fines (asbestic and/or associated minerals) often show up in the formation of special asbestos products as well as in the commercial production of asbestos papers, mill-boards, asbestos cement products, plastics and insulation materials, and in the filtration of blood plasma and wines.Numerous test methods have been developed in Canada and in England for use in the asbestos industry. Special treatments of asbestos fibers have been used to improve their physical and chemical properties and to eliminate impurities.Numerous problems connected with the use of asbestos fibers are discussed, such as the effects of asbestos on filtration, surface area, surface treatments using organic or inorganic materials, the surface charge on the fiber, the presence of magnetite and air pollution elimination. Biological studies on finely ground asbestos, when dispersed in 0.9 per cent sodium chloride solution and then sterilized and injected into hamsters, show that by reducing the dose, the tissue damage can be largely avoided. In these experiments, Arizona asbestos fibers were carefully extracted from the wall rock, finely ground, and examined chemically and micros-copically for any mineral impurities that might be present so that any effect on the hamsters would be directly due to the presence of the asbestos. The harsh Arizona fiber induced more extensive tissue response than the soft fiber when tested in hamsters."

Jan 1, 1969