Search Documents

By Marcel Vallée

"This text consists of two parts, comments on "Classification and Reporting of Mineral Resources for High-Nugget Effect Gold Vein Deposits," by S.C. Dominy, P.R. Stephenson and A.E. Annels, Volume 10, No. 3, pp. 215-233, and related comments on some features of the JORC Code.This paper is, in many respects, a very elaborate and valuable account of the problems encountered in the estimation and classification of high-nugget gold deposits. However, in some key areas, it appears to fall short of its objective to help "resolve satisfactorily most issues" and "contribute to improved estimation and classification" (abstract). One must realize that high-nugget effect gold deposits constitute a very narrow field, despite the occasional bonanzas. This is a field of mostly smaller sized deposits, where limited success and a significantly higher rate of failure occur relative to larger deposits of mostly lower grade. This is shown by the six deposits described in the paper. Thanks for contributing to greater understanding of these complex and nevertheless challenging deposits."

Jan 1, 2002

By M. Fainerman-Melnikova

The use of strong base ion exchange resins for the extraction of uranium was pioneered in the 1950?s. Ion exchange technology is applicable to dilute leach solutions such as those obtained from in-situ, heap leaching or in-plant processing of low grade ores. A further advantage of ion exchange processes is that fluidised bed technology allows for treatment of solutions with a relatively high concentration of suspended solids and resin-in-pulp technology can treat leach slurries. However, the extraction of uranium with strong base resins is severely affected by the presence of chloride ions in solution. In areas where high quality water is not readily available, the use of saline water as process water would extend the potential application for ion exchange in uranium processing. Our research program has studied the effectiveness of a wide range of commercially available ion exchangers in uranium extraction from saline solutions. In the present work, we examine the impact of salinity (ranging from chloride concentrations found in groundwater to those present in sea water), on the uranium extraction with weak base anionic resins (WBA). The effect of pH and the presence of the competing impurities are also discussed.

Aug 1, 2010

By Pierre Choquet

"The whole work carried out both in situ and in laboratory by a research group of the West German collieries is presented. This work has led to a design method of steel arch supports for gate roadways that gives full satisfaction in this particular coalfield. The method accounts for mining depth, the mining system (advancing or retreating), thickness of the coal seam and other parameters.Full statistics are then given on gate roadway supports of the ECCS (European Community for Coal and Steel) coalfields. They were collected by the author in order to show that the West German method can be applied to other coalfields as the long wall systems which are generally being used are very similar. Design calculations are conducted for each coalfield's case. They show that the method would have been able to predict in most cases the support actually used.Utilization of the design method is recommended to the Cape Breton Development Corporation 's mine operators because mining conditions, even though different from European ones, present a number of similarities which make it possible to apply the design method to their particular case.This procedure might be profitable in mines facing support problems in their levels and for any planning of future projects"

Jan 1, 1986

By A. B. Isaeva, A. Yu. Lein, A. A. Karpenko, V. V. Serova, A. P. Lisitzin, V. Yu. Rusakov, V. N. Lukashin

Abstract - The flux of sediment matter was determined using sediment traps near a black smoker ("Saracen’s Head," Broken Spur hydrothermal field) and the mineral and chemical compositions of the settled matter were examined. The metallic minerals are represented by Fe sulfides (pyrite and pyrrhotite), and Cu and Zn sulfides are also found in small and equal quantities. The hydrothermal suspended matter contains abiogenic calcite in amounts comparable to that in Ca sulfates. The content of silica and, specifically, of amorphous Si is unusually low. Such correlations between chemical elements and minerals, together with the isotopic compositions of S and C, are characteristic of a relatively young and active stage in the evolution of a hydrothermal system. Sediment traps within and under neutrally buoyant hydrothermal plumes collected biogenic material in addition to hydrothermal components. Microbial chemosynthetic production of organic carbon near the hydrothermal vent is comparable to primary production in the euphotic layer. Fe, Zn, Ca, Si, Ba and P are enriched in particulate matter in comparison to the background. A vast compound plume containing the discharge of multiple hydrothermal vents was found to the south of the Broken Spur hydrothermal field.

Jan 1, 1999

By Robert B. Parsons

"Next month will mark the anniversary of the release of an important federal study on a mineral policy for Canada. The study, entitled ""Mineral Policy-A Discussion Paper"", provides well-researched coverage of a broad range of issues that are of interest to the mining industry. Unfortunately, there is a real possibility that the discussion paper will wither and die on the vine, unless the federal and provincial governments, and the private sector, collectively ensure that some of the key considerations which are raised by the paper are acted upon.IntroductionAlmost one year ago, on March 8, 1982, Federal Mines Minister July Erola released an important study entitled ""Mineral Policy-A Discussion Paper"". The discussion paper, which presents the government's assessment of the opportunities and constraints facing the Canadian mineral industry in the 1980s, was prepared within the context o f three principal objectives-strengthening the resource base on which the industry rests, ensuring the adequacy of research activities needed to support development of the resource, and furthering the development of markets for the resource It is clear that, in today's economic climate, not even the most generous incentives would turn the industry around: what is needed is a sound base for future development, when this is possible. In this regard, the discussion paper is an excellent stepping stone, in that it reviews a wide range o f fundamental policy issues which touch on all facets o f the mining industry."

Jan 1, 1983

By C. W. Chao, M. Melashvili, F. Hilário

The processing of a bulk concentrate containing copper as chalcocite, enargite, bornite and chalcopyrite along with pyrite and precious metals of silver and gold was studied. A leaching study was undertaken to examine the application of the atmospheric acid leaching process to a bulk copper concentrate for copper recovery followed by cyanidation or thiosulfate leaching for gold and silver recovery. The extraction of copper exceeded 90% under some conditions and the recovery of gold and silver reached a maximum of 44 and 45%, respectively. A sample of bulk concentrate was roasted in air to oxidize the sulfides with release of sulfur dioxide followed by acid leaching of the roaster calcine and cyanidation of the acid leach solution. The copper extraction reached over 92% and the gold extraction exceeded 88%. The sulfur dioxide may be captured for acid production. INTRODUCTION The processing of a large primary copper deposit in Indonesia is under investigation. One of the possible routes for processing involves flotation of a bulk copper-gold concentrate followed by treatment by an atmospheric leach/SX-EW process for copper recovery. The atmospheric leach residue would then be leached for recovery of gold and silver. A second route involves roasting of the concentrate followed by acid leaching and SX-EW for copper recovery. The leach residue from the roaster calcine would then be leached for recovery of gold and silver. The roaster off-gases could be used for sulfuric acid manufacture, enabling the production of a valuable by-product. The Cobre Las Cruces (CLC) process (Munoz, Garcia, & Delgado, 2017) was designed to treat a resource of copper discovered close to Seville, Spain. The process was developed by Outotec with MK Gold (original project owner). INMET Mining subsequently purchased the deposit from MK Gold and built the copper processing facility. The CLC process is similar to the Mt. Gordon Copper process; except that OKTOP reactors have been installed instead of a low temperature, low pressure autoclave process. The plant was designed to treat 1.3 mtpa of ore at a grade of 6.2% Cu to produce 72,000 tpa of cathode copper over a 15 year project life. The main gangue mineral at Cobre Las Cruces was pyrite. The Cobre Las Cruces ore is therefore similar to a rougher flotation concentrate containing copper minerals and pyrite. The roasting of a rougher flotation concentrate can be designed to produce hematite, basic copper oxides and sulfur dioxide off gas. The acid leaching of the basic copper oxides may produce soluble copper for SX-EW recovery of copper. The sulfur dioxide off-gas may be used to make sulfuric acid.

Jan 1, 2019

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By A. Bhowmik

Uranium Refining is the process in which undesirable neutron absorbing elements such as Boron (B), Gadolinium (Gd), Cadmium (Cd), Europium (Eu), Samarium (Sm) and other heavy metals (Fe, Ni, Co, Ca, Mg etc.) are removed to make it nuclear pure. At present, Uranium refining is carried out by solvent extraction process by using organic based solvent e, g. TBP diluted with Kerosene. The above process generates lot of nitrate bearing liquid waste and degraded organic. In order to eliminate use of hazardous organic and ammonia for Uranium refining altogether, a new process has been developed. In the new process, Yellow Cake is dissolved in nitric acid and uranium peroxide hydrate is precipitated selectively from the solution leaving all the impurities in the solution by using commercial grade hydrogen peroxide at a pre-defined pH, U conc., temperature and stoichiometric quantity of hydrogen peroxide under mild agitation. The precipitate is filtered and washed with DM water to obtain nuclear pure product meeting purity standard as per ASTM C ? 753-99.The product is spray dried and calcined to obtain uranium oxide. The process eliminates use of organic, flammable, toxic chemicals, consumes less quantity of nitric acid and uses environfriendly chemical hydrogen peroxide. The process is simple and can be integrated in the mill. A patent application is entering national phase in several countries including CANADA and abstract/full paper is available in WIPO publication no: WO/2009/013759.

Aug 1, 2010

By T. G. Carter

"During the early part of the 1980s, four new surface coal mines commenced operation in the Province of British Columbia. Each represented a major investment in both persons and materials in order to protect this investment in one significant area-the fixed portion of the surface coal handling system-a substantial amount of work was undertaken to ensure that the system was well protected from an outbreak of fire. A great deal of effort in this field had already been made by those coal mines which had been in operation for a number of years and experience gained at these operations was utilized in determining the level and extent of fire protection for the new mines.This paper summarizes the major problems, and suggests some of the methods of solution, in providing an adequate degree of fire protection for surface coal handling systems. It will also discuss the potential for gas and dust explosions together with ways to minimize this potential.The Fixed Coal Handling SystemNote: The word ""fixed"" has been used in its present context to denote that part of the coal handling system where the coal is moved via fixed installations such as a conveyor. It differentiates from that part of the system where coal is moved by mobile equipment.The raw coal delivered to the truck dump will undergo two major processes on its way to the rail load out. The first will be at the coal preparation plant where coal of specified quality will be extracted from the raw feed to the plant. If this coal is of metallurgical quality, and sometimes if it is of thermal quality, it will pass through a thermal dryer where part of the moisture acquired during coal preparation will be removed, i.e. the second process. As the complexity of both the coal preparation plant and the thermal dryer is such as to warrant separate considerations they will not form part of this paper. Each of the processes, however, is generally, housed in its own building, thus, containment of any hazards is usually more attainable than those existing or caused in the rest of the system."

Jan 1, 1988

By Brian McIntrye, Bo Trygg

"The need for grinding mills of ever increasing capacity and greater feed openings has tended toward mill trunnion diameters being beyond the size limits for roller bearings.Hydrodynamic plain bearings need to be wide enough to achieve the necessary bearing pressure in order to obtain an oil film with sufficient carrying capacity at low rotational speeds. This greater width increases edge loading resulting from the deflection of the mill under load.Because of the high surf ace pressure involved, the life of support rollers and girth rings is often inadequate-fatigue leads to flaking on the contact surfaces. Heat treatment of the girth rings also has its problems.The hydrostatic shoe bearing permits unlimited trunnion diameter and a high carrying capacity. The self-aligning shoes compensate automatically for radial deviations and large deformations can be tolerated at the girth ring.The sliding surfaces are completely separated by oil under pressure, enabling negligible starting torque and good damping capacity to be achieved together with low rotational speeds.IntroductionHydrostatic bearings have been known within machine technology since 1865, when the Frenchman Girard received a patent for such a bearing. During the following 75 years, these types of bearings were used sporadically for thrust bearings, primarily in water turbines. The first usable radial bearing was not designed until 1938. Since the 1950s, when hydrostatic bearings started to come into use within the field of machine tools, extensive research and development work has been carried out at various institutions and research centres throughout the world. Many support problems are now solved by means of hydrostatic plain bearings and the primary factor in deciding to use them is their unique characteristics:• ability to carry high loadings• no starting torque• large damping capacity• no wear• large running accuracyThe hydrostatic shoe bearing has been developed specially for use in the heavy machine industry, with the requirements for high loadings and large support diameters which this market demands."

Jan 1, 1982

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By James Tuer, John R. Goode, Jim Cambon

"Hudson Resources Inc. (Hudson) has defined a major resource of high purity anorthosite (calcium feldspar) assaying about 30% Al2O3 at the White Mountain (Naajat) deposit in Western Greenland. Extensive beneficiation and evaluation testwork has shown that the material can be simply beneficiated to produce a feed material ideal for the production of low-alkali E-glass used for making glass fibre. An offtake agreement is in place with a major US fibreglass manufacturer and, subject to the mine construction schedule, shipments are scheduled for late 2016 or early 2017. In parallel with the E-glass program, Hudson has completed an initial program of metallurgical testwork which shows that the White Mountain anorthosite can be processed by hydro- and pyro-metallurgical processes to yield either smelter-grade alumina (SGA), suitable for conversion to aluminium metal, or a high purity, chemical/specialty-grade alpha-alumina (CGA) commanding a premium price. The process includes dissolution of the anorthosite in hydrochloric acid, HCl sparging to precipitate aluminium chloride hexahydrate (ACH), recycle of the ACH filtrate to leaching with a bleed stream processed for HCl regeneration from CaCl2, and two-stage calcination of the ACH to regenerate HCl and produce SGA and/or CGA. Calcium silicate and amorphous silica are marketable by-products. This paper discusses the White Mountain anorthosite deposit; the process testwork completed to develop production processes for SGA and CGA; production plans, and indicative economics.INTRODUCTIONHudson Resources Inc. (Hudson) holds a 100% interest in the Naajat Exploitation Licence in Western Greenland that cover the White Mountain high-calcic anorthosite deposit. Anorthosite is a calcium aluminosilicate of slightly variable composition but generally containing about 30% Al2O3. The alumina content is similar to that in bauxite and anorthosite has long been studied as a feedstock for the production of alumina. Other potential uses include feedstock for the high-end fiberglass (E-glass) industry and as a filler for use in paint and plastics."

Jan 1, 2016

The control of carbon concentration in a counter current carbon absorption circuit is critical to optimise gold recovery. MINTEK has developed a carbon movement controller to address this potentially problematic area in gold extraction. This controller reduces operator interaction by automating carbon movement. Elution schedules are entered into the control system, which then moves the carbon through the circuit into the first adsorption tank until enough carbon is available for elution. This is done while maintaining the specified carbon profile within the circuit. MINTEK has also developed an online-carbonconcentration- meter to measure carbon concentration in pulp. The meter uses an ultrasonic measurement technique. Long term testing has shown the measurement to be robust and require minimal maintenance. Results from a gold mine in South Africa’s well known Witwatersrand gold producing area has shown a decrease in soluble gold loss between 30 - 50% when the controller was used.

Jan 1, 2014

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By Donald S. Cameron

By dispersing gold in high surface area form supported on metal oxides, its inert character can be transformed to make economical, effective catalysts. Gold has already been demonstrated in a number of fuel cell applications such as gas phase catalysts, electro-catalysts, and electrical connectors. In this paper, the various types of fuel cell systems are reviewed, and several opportunities for gold identified. Low temperature fuel cells, including alkaline and solid polymer electrolyte types rely on high surface area platinum group metal catalysts which are highly susceptible to poisoning by low concentrations of carbon monoxide in the fuel supply. Hydrogen is frequently obtained by steam reforming hydrocarbons, followed by the water gas shift (WGS) reaction. A promising initial use for supported gold catalysts is in catalysing this WGS reaction. Research has shown that gold supported on iron oxide (Au/a-Fe2O3 ) WGS catalysts are more active than the current commercial copper oxide / zinc oxide catalysts, and effective at temperatures as low as 120oC. Products from reformer/ water gas shift reactors can be further purified by removing traces of carbon monoxide. If a small proportion of oxygen is introduced into the fuel gas stream, carbon monoxide can be preferentially oxidized to carbon dioxide even in the presence of hydrogen. Gold nanoparticle catalysts on iron oxide support (Au/a-Fe2O3 ) have exhibited higher activity than commercially available platinum on alumina (Pt/?- Al2O3 ) preferential oxidation catalysts. The low temperature of this reaction may make it feasible to incorporate these catalysts within the fuel cell itself. Proton exchange fuel cells provide several possible applications for catalytically active gold and its alloys. Carbon supported platinum group metals would benefit greatly from improved electrical conductivity if gold replaced some or all of the carbon support material. As electrode current densities are raised, electrical resistance constitutes an increasing proportion of voltage losses within the fuel cell. Dramatic reductions in cell stack voltage losses have already been demonstrated by reducing inter-cell contact resistance using gold plating. The low temperature oxidation properties of gold catalysts have been investigated in controlling gaseous emissions from direct methanol fuel cells, and gold also provides essential catalysis in building direct borohydride oxidation fuel cells. The prospect of a range of other applications for gold in fuel cells to contribute useful improvements in corrosion resistance and conductivity is assessed. Globally, fuel cells have been developed for a wide range of applications including stationary generators, cars and buses, industrial vehicles and small portable power supplies, each of which represents a substantial market. Hence there are likely to be many and varied opportunities for gold catalysts to contribute to the performance and economics of the systems being commercialized.

Oct 1, 2003

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019