Search Documents

By M. Bourassa, R. del Villar, S. St. Arnaud, J. Valenzuela

"Autogenous grinding is used quite frequently for mineral comminution as a result of its lower capital and operating costs. However, it is more difficult to control than conventional grinding, particularly when the autogenous or semiautogenous mill is the only comminution stage (i.e. no secondary grinding is available). Analysis of the control strategy used then becomes extremely important, a task that is greatly simplified by the use of an empirical dynamic simulator:This paper presents the methodology used in the development and the calibration of such a simulator for the autogenous grinding circuit of an iron are concentrator: The various steps are described: industrial data acquisition, preliminary treatment of the gathered information. and empirical modelling of the process. Finally, both the actual and the proposed control strategies are compared using simulation results.This exercise has shown that the variability of some of the controlled variables could be reduced through a better handling of the water addition and the use of filters on some of the signals used for control purposes. The reduction in variability of critical variables, such as power draw, would allow their average value to be increased without the risk of exceeding their safety values. Some advanced control techniques were also tested, with interesting results."

Jan 1, 1995

By SeyedBijan Mahbaz

Development of Geomechanical Earth Models (GEM) is a prerequisite to reservoir management, involving issues such as stress path analysis, prediction of induced seismicity and sanding initiation, and coupled flow-stress modeling that leads to more realistic predictions of oil rates and rock response. Part of GEM development is the stipulation of the 3-D lithostratigraphic disposition (geometry) which is used to choose the geomechanical units. The digital geological model is then populated with quantitative and semi-quantitative data on rock properties, fluid properties, saturations, initial conditions (p, T, [_]) and other information. Both fluid and solid properties are needed this requires integration of geomechanics skills with geophysical and rock physics skills, and this article deals with a subset of this integration process, with an example from two wells in southwest Iran.Rock physics approaches are used to predict reservoir rock and fluid properties with wellbore and 3-D seismic data, which are also used to interpolate rock mechanics properties to the inter-well regions. The first step in a generic rock physics approach is diagnostic and involves the introduction of a suitable Rock Physics model.Acoustic impedance (AI), shear impedance (SI), and density (_) are the fundamental rock properties usually derived using AVO equations, and these parameters, along with attenuation coefficients, can then be correlated to static rock mechanics properties that define deformability and perhaps even strength. In this study, Poisson Impedance is introduced as a new seismic attribute used for lithology and fluid differentiation in the FahliyanFormation (reservoir rock) in two oil wells in the southwest of Iran. To do this, a novel rock physics model was developed for this naturally fractured carbonate reservoir.Currently, these data are also being used to correlate to a limited rock mechanics data base to develop a more extensive GEM to serve as input to more general geomechanical and reservoir modeling tasks.

Jun 1, 2012

By M. Normandin

The performance of various polymers and other macromolecules used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocity and turbidity level, The Jar Test is widely used in the mineral industry to determine the efficiency of solid-liquid separation processes, particularly for gravity settler of the Bayer process. However, a high level of variability is found in the data obtained by this methodology, In this study, different parameters of the cylinder test procedure are evaluated to determine their role in the overall variability of the method, As demonstrated by laboratory testing, the overall variability can be considerably reduced by good laboratory practices.

Jan 1, 2005

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By C. L. Reichardt

Pressure exerted on gold producers by regulators, project financiers and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ?cradle to grave? approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or the receiving environment, either during mine life or after closure. Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill, as are certain principles pertaining to aspects of operations, worker safety, emergency response, training and dialogue with stakeholders. For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce.

May 1, 2007

By A. J. Neale, B. C. Flintoff

"A review of the dynamic rod mill-ball mill grinding circuit simulator developed at the University of Alberta, highlighting the modular structure and open-ended design, demonstrates the ease with which classical feedback control strategies can be designed and implemented. Various open loop simulations are presented to demonstrate the highly interactive nature of the grinding circuit and to indicate where potential control problems may be encountered. Closed loop simulations are examined, beginning with the basic SISO classical feedback control of circuit product size. Further improvement in the grinding circuit performance in the presence of various disturbances is realized through the application of a classical MIMO feedback controller. As an example of advanced (multivariable) control, static decoupling is implemented and shown to provide additional improvement in overall circuit performance.INTRODUCTIONIt has long been recognized in the processing industries that a dynamic process simulator is an indispensable tool in the design and evaluation of automatic control schemes. In mineral processing the lack of these simulators is felt to have been a major hindrance to the widespread implementation of effective process control systems. In particular dynamic simulation is a necessary precursor to any study of modern (as opposed to classical) process control methods. This paper discusses the development of a dynamic simulator that can be used to study various feedback control strategies. The simulation software provides a powerful educational tool for those individuals interested in grinding circuit control."

Jan 1, 1988

By Michael Nicol

A quantitative description of hydrometallurgical operations depends primarily on an understanding of the kinetics of the chemical and physical processes that take place in such operations. This paper will review the current status of kinetics in hydrometallurgy in terms primarily of the author’s experience in diverse unit operations. A distinction will be made between the popular use of models based on limited kinetic data and mechanisms which reflect the actual elementary chemical or physical steps involved in an overall process. Several examples will be used to illustrate this distinction. The proliferation of published papers of declining quality has resulted in the bequest to later researchers of outdated and often incorrect conclusions by a process that is often difficult to reverse. Some examples of these mysterious concepts will be examined and hopefully reversed. Finally, several examples will be given that identify significant gaps in our understanding of the kinetics of important processes that remain unresolved.

Jan 1, 2014

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By R. Ichimura

This paper summarizes the results of a five-year project, which aimed at improving the current method to process the arsenic-bearing smelter dust of El Teniente. This project, which was started in 2001, was carried out jointly by JOGMEC (Japan Oil, Gas and Metals National Corporation) and CIMM (Centro de Investigación Minera y Metalurgica, Chile), and was financially supported by the Japanese and the Chilean governments. In the new process, the smelter dust is leached with sulfuric acid to dissolve arsenic, which is subsequently precipitated as crystalline ferric arsenate (scorodite) at ambient pressure by controlling the crystallization and crystal growing stage. As a result, a stable form of ferric arsenate is obtained, which passes the U.S. E.P.A. TCLP limit of 5 mg/L As. Copper and zinc are subsequently recovered from the arsenic-free solution. The copper product can be fed into the main copper production circuit at the Las Ventanas Smelter and Refinery, whereas zinc is recovered as a marketable product. A demonstration plant was installed and operated at CODELCO's Las Ventanas Smelter and Refinery. The basic and detailed engineering design was prepared by Mitsui Mining and Smelting Co. Ltd (MMS) on the basis of a joint study done by JOGMEC, CIMM and CODELCO's Las Ventanas Division.

Jan 1, 2007

By R. Noriega, M. Suazo, V. Murariu

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By R. B. Casault, J. D. Boyd, D. R. Bell

"Full-scale sections of three different types of Grade 483 line pipe have been evaluated extensively. The variations in chemical composition, optical microstructure, tensile properties, hardness and Charpy impact toughness with specimen orientation and location were determined. Significant variations in several properties, notably Charpy shelf energy, impact transition temperature, inclusion content and ferrite grain size, were observed for different locations in the pipes. The results indicate that current specifications call for test samples for the most conservative locations, except for impact tests. Minimum Charpy impact values generally occur at the II2-width location, which may be a more appropriate specified test location than the present I/4-width location. The anisotropy of impact toughness, and the importance of low sulphur content and inclusion shape control for adequate toughness in the transverse/rolling-direction orientation were demonstrated. The orientation of impact specimens is critical for spiral-weld pipe, and the current specification test is non-conservative in that it can give results which are two to three times higher than the minimum value for the steel.IntroductionThis report presents the results of an extensive metallurgical evaluation of three different Grade 483 line-pipe steels. The sample material came from full-scale sections of line pipe, which represented current commercial practice at the time of manufacture (1975-1977). Since then, significant improvements have been made in the manufacturers' procedures for producing skelp and pipe, and the line-pipe specifications have been revised. Hence, the information in this report is dated in terms of current design, but it is unique and significant in several respects:"

Jan 1, 1982

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By Somchet Vongpaisal

This paper presents the R&D results on the development of a new knowledge-based system for predicting stope instability and associated unplanned dilution in deep underground mining operations. A new prototype was developed based on databases generated from 3D non-linear elasto-plastic finite element stress analysis, heuristic rules, and case histories. This prototype aims to assist mine operators to make decisions on strategic mine planning and feasibility in a quick and efficient manner thereby minimizing risk on ground failure and optimizing mining costs.

Jun 1, 2012

By R. O. Grieve

"IntroductionCALEY (1945) and Evans (1950) pointed out that certain instances of convergence between Devonian and Silurian horizons, frequently evident in wells drilled for oil and gas in Ontario, appear to be related to local thinning of salt beds in the Salina formation and they suggested that leaching of the salt beds may have occurred. Exploratory drilling by Imperial Oil Limited since 1945 has brought to light several examples of structures similar to those discussed by Caley and Evans. The writer has had the opportunity to examine cuttings and data from wells which penetrated these structures and the attempt to interpret them in the light of the theory of leaching and subsidence proposed by Landes ( 1945a) to explain the marked brecciation and deformation of Upper Silurian and Middle Devonian sediments which crop out in the Mackinac Straits region of northern Michigan has led to the observations presented in this paper."

Jan 1, 1955

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

The NorthMet deposit of PolyMet Mining is located in northern Minnesota, adjacent to the Iron Range. The deposit is polymetallic with values of Cu, Ni, Co, Zn, Pt, Pd and Au. The processing route selected for extraction of these values utilizes bulk sulfide flotation followed by hydrometallurgical treatment. The hydrometallurgical process has been thoroughly tested on the bench and pilot plant scale at SGS Lakefield Research. The major steps in the process are; ? Chloride-assisted total pressure oxidation for extraction of base and precious metals ?Thickening/filtration/washing of the barren residue from total oxidation ? Reduction and precipitation of Au, Pt, Pd from the oxidation solution ? Partial neutralization of autoclave acid using limestone ? Copper SXlEW for production of copper cathode ? Treatment of a portion of the raffinate from Cu SX to recover NilCo/Zn as either a mixed Ni-Co-Zn hydroxide or as separate Ni hydroxide, Co hydroxide and a Zn sulfate solution. ? Recycling of the remaining raffinate to the autoclave as coolant The process flowsheet, chemistry and bench/pilot plant test results will be reported in this paper.

Jan 1, 2007

By MKS Vel, S. Mukhopadhyay, R. Mishra

Off late, the criteria of selecting the refractory have acquired a trend line aiming to a cleaner environment and the utmost importance is given to the eco-friendly approach. The stainless steel making furnaces normally use mag-chrome refractories for the obvious reasons of changing slag basicity from acidic to basic. Such refractories generate toxic fumes and compounds with hexavalent chrome, which is unhygienic if inhaled. The present paper describes the development of a chrome free alumina magnesia carbon refractory, it's different test properties, simulative testing and microstructures. The optimum quantity and distribution of carbon in the brick restricts the carbon pick-up by the steel. Bricks with the same composition were manufactured in the commercial scale and used in a stainless steel making furnaces in USA. The performance of same refractory in this furnace was quite encouraging and at present the same quality brick has become a normal practice in this furnace. Since no chromite is used in making this brick, so no toxic compounds are generated environment remains pollution free.

Jan 1, 2004

By G. Plascencia, A. Warczok, M. Zamalloa, T. Utigard, N. Behnood

The objective of this investigation was to investigate interactions between high-grade copper mattes and Rexal 60DB direct bonded basic bricks. The infiltration and attack of Rexal 60DB bricks by copper matte and continuous converter matte was investigated in laboratory tests at temperatures up to 1300 °C. The brick dissolution and infiltration tests did not show any significant difference between the 70% Cu and the 81% Cu mattes. More metallic copper was visible in the pores in the case of 81% Cu matte. An important mechanism for direct-bonded magnesia-chrome brick destruction is that oxysulphides start to infiltrate the brick, followed by slow oxidation of the matte producing metallic copper and cuprous oxide, which then react with MgO and Cr2O3, primarily attacking the direct bonds of the brick.

Jan 1, 2004

By P. W. Waggitt

ABSTRACT From approximately 1986 until 2000, uranium production was at a historic low. In 2003, uranium mineral exploration surged, despite the global financial crisis; however, the shortage and aging of qualified and experienced operators and regulators might soon become a constraint to this upsurge. This is true for all types of engineers, geologists, other scientists, tradespeople, and technicians. The situation raises questions about how the global mining industry in general and the uranium sector in particular will cope with future staffing needs. In this paper, the author examines the current situation and describes how some organizations are seeking possible solutions.

Jan 1, 2014