Search Documents

By R. Ramirez

Atlantic Copper Refinery (Huelva, Spain) has operated the ISA permanent cathode technology since 1995. The current production rates are 260,000 t/y cathodes and 730 t/y anode slimes. These slimes undergo an atmospheric leaching in which their copper content is reduced from an average value of 24 % to 16 %. In June 2005 an optimization study of the leaching conditions was carried out aimed at lowering the copper content in the slimes to less than 8%. At the same time, a new mixer (Outukumpu Technology GLS-mixer) was installed in one of the three leaching reactors. As a result of the improvement of the leaching performance and to prevent the return of tellurium to the tankhouse, a cementation plant was commissioned in July 2005 to ensure a Te content below 50 ppm in the Cu-rich leachate. This paper describes the results of the improvement of the leaching conditions and the operation of the new tellurium removal plant.

Jan 1, 2007

By B. T. Lu, J. L. Luo, T. Yu, C. W. Chen

In this paper, the synergism in erosion-corrosion process occurring in oil sand wastewater transportation caused by the interaction of mechanical and electrochemical factors was experimentally investigated. The erosion-corrosion tests were conducted with A1045 steel in synthetic slurries comprising tap water and silica sand. The material loss due to corrosion-enhanced erosion was assessed with the chemo-mechanical model developed by the authors recently. The results indicate that the material loss produced by corrosion-enhanced erosion at the open circuit potential can be formulated as a linear function of logarithm of corrosion current density. The wastage caused by the erosion-enhanced corrosion was analyzed based on the concept of non-equilibrium thermodynamics. The material loss induced by the erosion-enhanced corrosion is approximately a linear function of overall erosion rate measured in synthetic slurries, indicating that erosion-enhanced corrosion could be reduced by adopting surface strengthening techniques to improve the resistance to the plastic deformation in surface layer.

Jan 1, 2004

By Christopher W. N. Anderson

Induced hyperaccumulation of gold by plants was first reported in 1998 by researchers from Massey University in New Zealand who proposed the idea of mining gold using plants (phytomining). Since that time research has been conducted to understand the conditions under which plants can be made to take up economic amounts of the metal. One key focus has been on the geochemistry of gold-rich soils, leading to a diagnostic test that can predict how suitable a particular soil might be to gold phytomining. Field trials have been conducted at several locations around the world in collaboration with industry partners. A Decision Support System has been developed to assist in the design and management of phytomining operations, and economic modeling has been carried out to set targets levels for phytomining technology. Novel studies are now examining the form of gold in plants. Research suggests that plants may store gold as discrete metallic nanoparticles in leaf and stem tissues, an observation that may lead to new ways to recover the metal from harvested biomass.

Oct 1, 2003

By D. Runnels, A. Allaire, J. Fournier, Y. Sylvestre, F. Robichaud

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By Serge Vézina

Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of our modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/communication technologies, better educated populations, climate change, long range transport of toxics and the increasing influence of NGOs and multistakeholders. As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental Management Systems (EMSs) have emerged and have been introduced to meet not only the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO-14 001) is a common practice. Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities and a variety of government infrastructures to obtain a ?licence to operate?. This paper presents the structure of our EMS and how we have adapted its implementation to our operations in South America.

May 1, 2003

By Larry M. Southwick

Processing of ores to recover metals usually generates large amounts of waste materials, such as rejects from concentrating operations, tailings from leaching and slags from smelting. These wastes often contain substantial amounts of iron and other metals, recovery of which are often considered to be of commercial value. Earlier versions of this paper investigated a number of processes built to recover iron from a variety of copper processing residues. This paper will extend that coverage to residues from nickel/cobalt, aluminum, asbestos and oil shale processing and coal plant fly ash. Products of interest are iron, ferroalloys, magnesium and aluminum. While none of these processes achieved long-term commercial success, their efforts cover the gamut of problems that must be addressed in treating dirty and difficult materials to recover generally low-value products. An Adept is an alchemist who can create a Philosopher's Stone, which could transmute base metals into gold. In 1701 in Berlin one Johann-Freidrich Böttger, a nineteen year old apothecary's apprentice, told King Frederick I that he could discover how to make the Stone. He failed and fled Frederick's wrath to Poland. He failed again, and King Augustus II threw him in jail. Then, in 1709, he discovered instead the secret of making Dresden china, certainly a more practical search. His failures in alchemy led to the nickname Adeptus Ineptus.

Jan 1, 2004

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By Frederick Biery

Outline ? Project Challenges ? Results from 100 recent projects ? What factors are driving the best and worst projects ? A look at recent mining projects ? Conclusions

May 1, 2009

By Jennifer Young

Presentation Outline ? Introduction ? Aboriginal Inclusiveness ? Common interpretations, practices ? Aboriginal Community Expectations ? Lessons Learned ? Native Code of Conduct Introduction Jennifer Young ? Nestu'et (Mi'kmaq) means: becoming wiser, becoming more knowledgeable Aboriginal Inclusiveness ? Internal hiring strategies (affirmative action) ? Incorporating cultural awareness programs ? Approaches in governmental/organizational policy development Practices in negotiating economic development and fiscal sharing strategies

May 1, 2010

By Robert C. Lo

As tailings dams grow in physical size, their impact on public safety and the environment also increases in severity. Over the last three decades, tailings dam engineering has evolved from largely "trial-and-error" methods to a mature, multi-disciplinary engineering endeavour. This paper reviews the current practice of tailings disposal, and the evolution of tailings dam engineering. Key factors affecting dam integrity and examples of dam failures are then highlighted. Finally, the paper reviews some of the recent trends that lead to new challenges to the mining industry. These challenges include: coping with heightened public concern about dam safety; balancing potential conflict between seismic and environmental requirements; and addressing issues introduced by globalization of the mining industry. Institutional responses and technological tools available to meet these challenges are also outlined.

May 1, 2001

By Robert Bégin

Reconnue pour son expertise en formation minière, la Commission scolaire de l?Or-et-des-Bois, dans le cadre du projet MRN-ACDI en Bolivie, a reçu en 1999 le mandat d?implanter un programme de formation en santé et sécurité du travail dans les mines artisanales boliviennes. À la suite d?une mission préliminaire en Bolivie et de la venue à Val-d?Or d?une délégation bolivienne, il a été convenu de l?adaptabilité du modèle québécois du programme de «formation modulaire du travailleur minier» au contexte bolivien. Là-bas, les méthodes de travail sont essentiellement artisanales et la pauvreté extrême des mineurs les pousse à prendre des risques quotidiens. Les modules de formation priorisés sont : «Introduction à la santé et à la sécurité du travail», «Principes d?écaillage» et «Matériel de sautage et explosifs». Les universités Tomas Frias de Potosí et Siglo Veinte de Llallagua sont responsables de l?élaboration et de l?implantation du programme dans deux coopératives minières de leurs secteurs. Dans une phase ultérieure, le programme sera étendu à plus large échelle. Enfin, des missions de suivi et d?encadrement sont effectuées périodiquement par les représentants de la Commission scolaire de l?Or-et-des-Bois. La formation en santé et sécurité dans le milieu de travail constitue un nouveau défi pour les universités boliviennes et une source d?espoir pour les mineurs des coopératives minières.

May 1, 2001

By Michel Noël

Cet article présente une compilation partielle des mesures adoptées pour la fermeture des haldes de stériles pour des mines situées au Canada et en Alaska, et dont le climat comporte des hivers froids. L?article présente également le processus de sélection qui a été suivi pour certaines de ces mines. Les exploitations minières produisent habituellement des quantités de stériles qui peuvent être importantes. De plus, la nature du dépôt minier ainsi que la roche mère vont souvent entraîner des impacts sur l'environnement. Ces impacts doivent être gérés non seulement durant les opérations minières, mais souvent à très long terme après la cessation de l?exploitation minière. Les plans de fermeture de mine doivent par conséquent procurer des solutions à très long terme, voire même à perpétuité dans bien des cas. Le processus de sélection implique souvent l'évaluation des risques liés aux responsabilités environnementales et financières. Il doit considérer l?aspect scientifique, comporter une définition des objectifs, tout en incorporant une gestion des ressources et des plans de travail. La planification de fermeture est essentiellement un exercice de prise de décisions comportant des contraintes. Une matrice de classement basée sur la performance et le risque est souvent développée durant ce procédé pour identifier les options préférées. Les études de cas présentées dans cet article présentent quelques exemples. L?état des connaissances sur le drainage acide minier provenant des haldes de stériles a augmenté considérablement au cours des dernières décennies. Ceci n?a pas nécessairement augmenté le niveau de complexité des méthodes adoptées pour la fermeture. Une approche qui est fréquemment utilisée consiste à stabiliser les pentes des haldes de stériles en abaissant la pente des talus pour ensuite recouvrir les stériles d?une couche de sol pour soutenir la végétation. De telles couvertures empêchent les animaux d?avoir un contact direct avec les stériles, minimisent l'érosion et réduisent l'infiltration à divers degrés. L'inclusion d?un traitement des eaux dépend évidemment de la qualité de l'eau au point de déchargement.

Nov 1, 2008

Toronto 2013 Proceedings

May 1, 2013

By C. B. Webber

"Sherritt Gordon's experience with rubber mill liners began in 1964 at the Lynn Lake Farley Mine and continued at the Fox Mine in 1960, and the Ruttan Mine in 1973. This paper describes the history of the performance of rubber mill liners at the three mine operations.LYNN LAKE - FARLEY MINEThe Lynn Lake Farley Mine, which ceased production in 1976 due to exhausted ore reserves, was a 3500 T.P.D. copper-nickel operation; consisting of two parallel rod mills followed by three stages of ball mill grinding. A circuit modification in 1964 necessitated one of the tertiary ball mills to be used as a pyrrhotite regrind mill. This 8' x 5' Hardinge conical mill drawing 225 HP was initially installed with steel liners and lifters. After several months of operation a routine inspection revealed severe channeling and washing behind the liners which was threatening to erode the ball mill shell. It was thought that the highly acidic condition in the mill, due to grinding 100 º6 pyrrhotite, was accelerating the wear of the steel liners. At this time it was decided to reline the mill with rubber liners to see if the wear problem could be relieved, and in December 1964 a set of Skega rubber liners were installed."

Jan 1, 1981